Why not wmc7, like vista allow you to browse the internet on your TV for xbox 360

Similar Questions

• Allowing internal users browse the internet

  Hello

  I have a PIX 515E with IOS 6.2. I am currently using ISA server as a proxy server to browse the internet. I would like to change this and allow users to browse the internet through the PIX firewall. This wud give me an additional IP address on the ISA server computer.

  Can you tell me what commands do I need.

  Hello

  Using the ACL (named in this case) you do the following:

  > access inside permit tcp host XXXX list any eq www

  > access inside tcp list deny any any eq www

  > ip-list access to the Interior for a whole

  .. now configure the ACL inside with a statement of the Group of access interface that is

  > group-access to the Interior in the interface inside

  (NOTE. IN THE FIRST ACL ABOVE XXXX IS YOUR IP OF ISA)

  In addition, after you set up the ACL make sure to a wr m (write to memory)

  Hope this helps-

• RV180 VPN connects and allows you to browse the files, but falls when opening a file.

  Last week, we received our 300Mbps fiber connection. We bought the RV180 due to its high performance, and he manages the speed perfectly.

  However, when you set up VPN, I encountered a strange problem.

  Establishing a QuickVpn or PPTP is simple and connection is no problem. But I'll be fine. I can communicate with QuickVpn or PPTP and find a NAS or PC directory structure, but when I try to open a file the VPC connection drops.

  I activate the remote management.
  I can ping google.com f-l 1472 without fragmentation, so a WAN MTU of 1500 should be ok.
  I have tried disabling attack prevention firewall.

  I have install the following experience: the firmware update (1.0.2.6), restore the default settings.

  Set up the RV180 as follows:

  IPv4 WAN (Internet)

  ------------------------------------------------------------------

  Internet connection type: Automatic Configuration - DHCP

  DNS Server Source: Get dynamically for ISP

  MAC address of the router: use the default address

  IPv4 LAN (local area network)

  ------------------------------------------------------------------

  Host name: RV180

  IP address: 192.168.75.1

  Subnet mask: 255.255.255.0

  Mode DHCP: DHCP Server

  Domain name: LCDVT

  From the IP address: 192.168.75.100

  End IP address: 192.168.75.254

  Rental time: 24

  DNS Proxy: enable

  Preventing attacks

  ------------------------------------------------------------------

  WAN (Internet) security controls

  Meet Ping on WAN (Internet): disabled

  Stealth mode: disabled

  Floods: disabled

  LAN (local area network) security controls

  Block UDP Flood: disabled

  Parameters of the ICSA

  Block the anonymous ICMP Messages: disabled

  Block fragmented packets: disabled

  Block multicast packets: disabled

  VPN users

  ------------------------------------------------------------------

  PPTP server: enabled

  From the IP address: 192.168.75.50

  End IP address: 192.168.75.99

  Table setting VPN Client:

  ---------------------------

  No: 1

  Enabled: enabled

  Username: lcdvt

  Password: *.

  Allow the user to change the password: NA

  Protocol: PPTP

  Web access

  ------------------------------------------------------------------

  Access on the LAN of HTTPS Web Interface: enabled

  Remote management: enabled

  Type of access: IP range

  Start of range: 192.168.75.1

  End of series: 192.168.75.254

  Port number: 443

  Remote SNMP: disabled

  The rest of the menu options are, except for logging policies where I have everything turned on by default.

  In this experiment, I connect from a remote location, start navigating among directories of the drive without any problems and then open a file, after which the VPN connection falls (or some process breaks down). After the transfer of a few 100 KB blocks the VPN connection.

  Error logs

  ------------------------------------------------------------------

  Thu Mar 20 00:39:18 2013(GMT+0100) [rv180] nimfNetIfaceTblHandler [System] [NIMF]: could not get LedPinId

  Thu Mar 20 00:39:25 2013(GMT+0100) [rv180] [System] [PROGRAM] IP: 62.45.238.236

  Thu Mar 20 00:39:25 2013(GMT+0100) [rv180] [System] [PROGRAM] BCAST: 62.45.239.255

  Thu Mar 20 00:39:25 2013(GMT+0100) [rv180] [System] [PROGRAM] subnet: 255.255.254.0

  Thu Mar 20 00:39:25 2013(GMT+0100) [rv180] [System] [PROGRAM] GW: 62.45.238.1

  Thu Mar 20 00:39:25 2013(GMT+0100) [rv180] [System] [PROGRAM] DNS1: 62.45.45.45

  Thu Mar 20 00:39:25 2013(GMT+0100) [rv180] [System] [PROGRAM] DNS2: 62.45.46.46

  Thu Mar 20 00:39:25 2013 (GMT + 0100) [rv180] [System] [PROGRAM] Interface: eth1

  Thu Mar 20 00:39:32 2013(GMT+0100) [rv180] nimfNetIfaceTblHandler [System] [NIMF]: could not get LedPinId

  Thu Mar 20 00:40:58 2013(GMT+0100) [rv180] nimfNetIfaceTblHandler [System] [NIMF]: could not get LedPinId

  Thu Mar 20 00:41:10 2013(GMT+0100) [rv180] [System] [PROGRAM] IP: 62.45.238.236

  Thu Mar 20 00:41:10 2013(GMT+0100) [rv180] [System] [PROGRAM] BCAST: 62.45.239.255

  Thu Mar 20 00:41:10 2013(GMT+0100) [rv180] [System] [PROGRAM] subnet: 255.255.254.0

  Thu Mar 20 00:41:10 2013(GMT+0100) [rv180] [System] [PROGRAM] GW: 62.45.238.1

  Thu Mar 20 00:41:10 2013(GMT+0100) [rv180] [System] [PROGRAM] DNS1: 62.45.45.45

  Thu Mar 20 00:41:10 2013(GMT+0100) [rv180] [System] [PROGRAM] DNS2: 62.45.46.46

  Thu Mar 20 00:41:10 2013 (GMT + 0100) [rv180] [System] [PROGRAM] Interface: eth1

  Thu Mar 20 00:41:19 2013(GMT+0100) [rv180] nimfNetIfaceTblHandler [System] [NIMF]: could not get LedPinId

  Warning logs

  ------------------------------------------------------------------

  Thu Mar 20 00:39:13 2013(GMT+0100) [rv180] [System] [DHCPC] dhcpcDisable: removed dhclient.leases

  Thu Mar 20 00:40:54 2013(GMT+0100) [rv180] [System] [DHCPC] dhcpcDisable: removed dhclient.leases

  Sat 1 Jan 01:02:43 2011 (GMT + 0100) [rv180] [Kernel] [KERNEL] [23.090000] /home/aruns/rv180w/updated_dec19_final/beta-v1/rv180w-common/comps/gpl/ipset/src/ipset/kernel/ip_set.c: ip_set_create: no type set 'nethash', 'setPublicNet' has not created value

  What I am doing wrong? Or the device?

  I am interested in what the solution to these problems.  Research on get a rv180...

  First car of Huntsville and bike e-magazine: www.huntsvillecarscene.com

• The product key you entered will not work with this edition of Windows Vista. You must run the Windows Vista Setup program or enter a Windows Vista business product key

  Product key bad for the wrong version?

  Hello

  Recently the computer in business inherited from a friend, very fast and very good. Regardless of the operating system no - geniue, is with Vista Business, while the thumbnail of authentication is Vista Ultimate. I took a screenshot of what it says when I put Vista Ultimate product key: (it does not appear if you are unable to use it: P)

  http://S13.PostImage.org/57nfn5pqv/vistareg.jpg

  He said: "the product key you entered will not work with this edition of Windows Vista. You must run the Windows Vista Setup program or enter a Windows Vista Business product key."

  How would the installation of Windows Vista? My files would still be there when you need him? My drivers would still exist? No matter what to get deleted or become unusable? He would return to SP1? Any response is welcome.

  You can order form of the manufacturer's recovery media.

  The reason why the system as non-authentique shows currently is using a license in Volume KMS - these licenses must be re-activated at least every 6 months by connecting to the KMS user license activation server.

  It will require a reformat and reinstall whatever you do, unless you can connect to the KMS - Volume media server cannot be upgraded under normal conditions.

• What happened to the button on the address bar which allow you to see the pages you had been so that you don't have to click the back button several times? I use it all the time and it is not on FF4.

  What happened to the button on the left end of the address bar which allow you to see the pages you had been so that you don't have to click the back button several times? You can look at the drop down window of pages and just choose whatever you want. I use it all the time and it is not on FF4. I want to go back to the old FF.

  If you right click on your back button, or click and hold down the mouse button, it will display the list. (I prefer a click-right, because sometimes my fingers slide when I try to click and hold)

• "The product key you entered will not work with this edition of windows vista. You must run the windows vista Setup program or enter a windows vista product key. »

  I bought a laptop HP three years ago in Dubai, now I am in India, my family problem does not activate windows vista and also use it now, I try to use but asked the system to activate product key not found the product key at the bottom of my laptop I enter the product key but the system says "the product key you entered will not work with this edition of windows vista.»  You must run the windows vista Setup program or enter a windows vista product key. "In my company sticker a HP laptop, it says" Windows Vista Home Premium, also found in computer ownership 'Windows Vista Ultimate' and as low property said: you must activate today and return their product ID: 89580-014-0000025-71152, but in my laptop near the product key, wrote a different number which is "89580-014-0000025." what is the problem and how to solve that advice me please. ""

  Hello

  You can use this Recovery Partition to reinstall Vista to his new condition with the right edition of Vista.

  This recovery partition was photographed on your hard drive by HP during the manufacturing of the factory.

  You press F11 on startup to start the process of recovering back to factory settings.

  Here is the information about HP.

  http://h10025.www1.HP.com/ewfrf/wc/document?DocName=c00809678&LC=en&DLC=en&cc=us&product=18703

  If the recovery partition is damaged, you can buy HP's Vista recovery discs for a small fee.

  If HP's Vista recovery disks, you may need to try this instead:

  You can also borrow and use a Microsoft Vista DVD, which contains the files for the different editions of Vista (Home Basic, Home Premium, Business and Ultimate) must be installed. The product key on your computer / Laptop box determines what Edition is installed.

  Other manufacturers recovery DVDs are should not be used for this purpose.

  And you need to know the version of 'bit' for Vista, as 32-bit and 64-bit editions come on different DVDs

  Here's how to do a clean install of Vista using a DVD of Vista from Microsoft:

  "How to do a clean install and configure with a full Version of Vista '

  http://www.Vistax64.com/tutorials/117366-clean-install-full-version-Vista.html

  And phone Activation may be necessary when you use the above installation method.

  "How to activate Vista normally and by Activation of the phone '

  http://www.Vistax64.com/tutorials/84488-activate-Vista-phone.html

  See you soon

• Send Adobe allows you to choose how many days your files can be downloaded - as with Adobe send now? Also, why don't I see the antivirus message more with 'Send' versus 'Send now'?

  Send Adobe allows you to choose how many days your files can be downloaded - as with Adobe send now? Also, why don't I see the antivirus message more with 'Send' versus 'Send now'?

  There is no automatic expiry of sent files coming. If you want to prevent to be downloaded, you can cancel them at any time.

  All files uploaded to our servers * are * virus research. I don't know why we are is no longer displayed the message while scanning is in progress. I can ask the team if you want me to.

• Qosimo F20: WLan adapter forget window allows you to configure the settings

  I recently changed a linksys wireless router to bt home hub but white since doing so I have been informed of bt, the wireless network adapter (intel (R) PRO/Wireless 2200BG Network adapter)

  I use keep forgetting window allows you to configure the settings. so every now and again I have to right-click on the icon in the lower right, choose View available wireless networks, click on change advanced configuration, and then click on the tab and then wireless networks check use windows to configure the box at the top left.

  I'm very novice all help would be appreciated.

  Post edited by: johnsmith3131

  Hello John

  As you know all configurations can be specific and depend on the used material. Believe me on this path it is not easy to say something concrete, because the BT home hub white is unknown to me and can I just suggest that you carefully read the user manuals which must be detailed explain how to connect external devices to the hub.

  By the way: you have something like this http://digital-lifestyles.info/display_page.asp?section=distribution&id=3404?

• Why not Time Capsule shows under "other devices" in the Finder?

  Why not Time Capsule shows under "other devices" in the Finder on my MAC?

  "Devices" are connected directly to a Mac and would include things like USB hard drive, FireWire drive and Thunderbolt drive, etc.

  The Capsule is a "network" connected to a network drive... If the operating system on your Mac behave, Time Capsule will appear in the Shared section.

  If you have added a NAS (Network Attached Storage) disk, this product would also appear in the Shared section.

  A wireless printer can also appear under shared.

• When I am browsing the internet using Safari and I'm looking for something like a plumber he gives met with responses from an area not my own.  How can I change this?

  When I'm surfing the internet using Safari looking for a product (like a plumber) all my suggestions come from the vicinity of Tyler, Texas.  I live much closer to Dallas.  How can I change that.  Thank you!

  You have location services? Are you allowing access from Safari to your location? You must check in the settings > privacy > Location Services > Safari Web sites. If she knows exactly where you are, then you can get these errors.

  I'm sorry, I just realized that you were referring to the Mac computer. My answer was for an iPhone. I can't help you with the Mac.

• NH-1005 ver 2.2 hub allows you to restore the default settings

  OK, I have a worm hub 2.2 NH 1005 that I used a little more than six months, and I need your advice on restoring the default settings.

  the web-based configuration page can be accessed through 192.168.2.1 on IE, but my step son was trying to fix the nat definition for its xbox 360 (not so hard to do...) and changed the settings under remote management to turn off. now, it is not possible to connect to access based on the Internet web page.

  is there another way? Is there a restore defaults button in the web page, but no button or other basis on the hub itself. any advice, other than to get rid of it and replace?

  So in this case you should check the settings of your DSL modem. Like most of the DSL modem has a built-in DHCP server. Then maybe you lose connectivity to your modem DSL itself.

  As your HUB is a dumm device and it dosent have any parameters, or you can reset your HUB. Only, you can make a normal feeding cycle and which will not solve the problem.

• Enter CC allows you to send regular photos to your libraries?

  The only option that I understand for sending photos to Capture CC is the look section. When I create a new library, I'm not able to add these photos in my Photoshop document. She LOOK photos can go first and sequelae.

  This App allows you to send photos to your libraries? Thank you very much for your help!

  Hello! I try to understand what is happening here.

  So you use adobe screenshot. Adobe Capture gives you 4 applications that you can use:

  Color

  -Color lets you create palettes. You can create palettes using existing images or score you camera directly to what is in front of you. If the purpose of color creates for example Illustrator or Photoshop color palettes. They will disembark in your libraries

  GLANCE

  -look almost the same as color, but what you get is a search for color you can use successfully in e.g. sequelae. Your eyes will land in your library

  FORM

  -form transforms photos into vectors. You can use your existing or new photos. Once you have created a form, which is a vector of the apps created a photo, you can save it in your library and use it in your client application. As for the color and appearance, your silhouette will be in the library

  BRUSH

  -brush is an application that allows you to create brushes for other mobile applications or desktop applications. As in all others, you can take a photo or an existing photo allows you to create a new brush. The coals can be saved and appear in your library.

  For all applications allow you to open pictures from your mobile or tablet or take new and use them for the purposes of the application itself.

  If your goal is to work on an image and the image that is sent to a desktop app, maybe you should check Photoshop Fix or Photoshop Mix. They too are Adobe apps, but are not available for all mobile phones and phones yet.

  Let me know if I am clarifying the right thing here

• What version of Adobe allows you to change the page on some pages orientaion and save the document with just a few of the tours pages?

  What version of Adobe allows you to change the orientation of the page on some pages and save the document (PDF) with only a few of the tours pages?

  Adobe is the name of the company, not the software as many people say. Since you want to know the exact software, it is important to know that.

  Any version of Acrobat Standard or Acrobat Pro to do this. These are commercial software (a cool weather or subscription).  The free Adobe Reader or Acrobat Reader cannot do this.

  Tip: there are two ways to turn the pages; alone will save him.

• DDoes iCloud keeps the deleted content to your iPhone (thus allowing you to free up space on your phone, but keep the content)?

  DDoes iCloud keeps the deleted content to your iPhone (thus allowing you to free up space on your phone, but keep the content)?

  N ° once you delete data from iCloud, it is deleted from your phone.

• Several times after that I opened Google it does not connect to the internet. Has worked for a long time, and now it will not. Sometimes it opens if you "Refresh" sometimes not. Please help.

  Several times after that I opened Google it does not connect to the internet. Has worked for a long time, and now it will not. Sometimes it opens if you "Refresh" sometimes not.  Help, please. It has been stable over the years and now it will not work. I get no help when I diagnoise of problems, but I never. It has been checked and rechecked. PitStop does not even recognize a problem. I could change the homepage, but I prefer to use Google if it works. Frustrating.

  You may need to update your toolbar, google has made some changes just about everything and possibly that the page is not where it used to be.