Will not re-start

Similar Questions

• Satellite U400 will not usually start upward

  Hi all

  I have a Toshiba Satellite U400-217 (PSU44E) running Windows 8.

  Worked fine until a week ago. Now, when I turn it on, the lights are, there is a memory hard drive spin (1 second) - and then nothing. Above the keyboard lights stay on, but the screen remains black.

  I read a use Reset where you take the battery and the power cable on and press and hold power for 30 seconds, then plug the power cable in, starting at the top, stop, reinsert the battery and start again.

  However, the machine still primer not after 30 seconds the hold button. I always get just the lights and nothing else.

  However, the machine will start usually fine on an attempt to out all 30 or more.

  It's boring - ideas or suggestions very welcome.

  Thank you very much

  KaiBosh

  > However, the machine will start usually fine on an attempt to out every 30 or more.

  In my opinion, you should first check the HARD drive
  A friend of mine installed Win 8 on the new computer laptop from another manufacturer
  After a while that the laptop will not start I thought its something wrong with the card mother, but in the end it was just a HARD drive failure

  To be honest I n don't know if his only problem disk HARD but in my opinion, the HARD drive is one of the first pieces that need to be checked
  OK, in the worst case, it could be possible that dysfunction of this mobo.

• Thing strange keyboard, ESXi will not finish starting up until I hit a button on the "Vmkernel loaded successfully."

  During installation and during boot after installation, the yellow, both initialization screen installation and startup stops at "Vmkernel loaded successfully" and will not go ahead until what I hit any key on the keyboard. Once you press a button, everything is moving along well. I even tried to start after installation without a keyboard in and it stops at the same place. Once the keyboard is plugged in, it starts right. It is a PS2 Keyboard. Will try and low rev bios once and try a USB keyboard, but was curious if anyone had seen this before? Thank you!

  If you search the forum for the keyboard, you will find similar issues like this - http://communities.vmware.com/message/1113079#1113079.

• Spool print will not be started.

  My spool print will not run.  I went and restarted and it won't stay running.  I try to add a printer, and he says he can't because spool it printing stops again.  Would it be useful to reinstall windows?

  My spool print will not run.  I went and restarted and it won't stay running.  I try to add a printer, and he says he can't because spool it printing stops again.  Would it be useful to reinstall windows?

  It would probably help if you reinstalled Windows, but this is a drastic measure and almost certainly useless to take in response to this error.

  When you restart the print spooler, it immediately turning off or only when you try to print?

  Assuming that you have an up-to-date antivirus application and have recently scanned withMalwareBytes Antimalware and SUPERAntiSpyware as you are reasonably confident that your computer is free of malware, the most likely reasons for the print spooler not running are a corrupt print job stuck in the queue or a damaged printer driver.

  Follow the directions here: http://www.coribright.com/windows/Article_One.htm

  If you had or have a Lexmark printer, check out these instructions: http://members.shaw.ca/bsanders/CleanPrinterDrivers.htm

• Vista Service Pack 2 will not ' cold' start

  I have a Dell Studio 1737 I bought last week. Windows Vista Service Pack 2 update offered. I selected it and ran through the upgrade. He completed all 3 steps and rebooted. Seems to work very well. I turned off the laptop and went to bed.

  This morning, the laptop complete the power on self test and went to boot Vista. Nothing for 20 minutes then a warning to the blue screen. He himself deleted before that I could read what caused the BSOD and then tried a reboot. Black screen for 20 minutes with no hard disk activity. Manually, I forced a stop down and loaded the boot menu. Choose the Startup Repair. After 30 minutes, advised by the screen to try a restore to an earlier version running. It took another hour, but it worked.

  Update Windows SP2 offered again. Thinking that it may have been an installation failed, tried again. Downloaded and installed SP2, these three steps successfully completed. Yet once computer rebooted (hot start) and did fine. Shut down the system and restarted (cold boot). Same results! MESSAGE completed and handed over to Vista SP2 and then black screen. Took me another 90 minutes, but I restored it to Vista SP1, now it works well.

  So I can run Vista Home Premium 64 bit SP1 without problem but SP2 does not work?

  Update looking for a 64-bit SP2 or just blindly offer software?

  I think that Microsoft is using me as a Guinea pig.

  I'm supposed to receive a DVD of Windows 7 from Dell, in an upgrade. I am wary to install it now since SP2 does not work yet. I was so angry, I jumped out early without digging further, but now I think I might very well be better to stay with SP1 and jump more "updates" unless someone can tell me what is happening here.

  How SP1 can be compatible, but SP2 is not?

  And if all you can afford is a response of canned paste, boiler, don't waste your time. All it will do is make me madder.

  Apparently, offered to customers by Windows Update SP2 update is NOT a complete or is not 64-bit capable.
  

  UH - huh...

  1. What is the full name of your application or the installed antivirus security suite and when (date about) because your current subscription expires?  What (other than Defender) anti-spyware applications are installed?  What third-party firewall (if applicable)?

  1B. were ALL of those applications that run in the background when you initially tried install SP2?

  2. do you have a free trial Norton, or a test of free McAfee [a] come preinstalled on the computer when you bought it? (No matter if you have never used or activated).

• Computer Vista will not complete start up once the updates have been installed

  Office worked well on 20 January, until the update when you restart it should start going to black screen with cursor. I tried to fix it, but it does not work. I tried the system restore to an earlier date but gives the error. Does anyone have ideas, which is false.

  Thank you

  Lisa,
  At this point if you have a way to back up your data, I suggest that do you so as soon as possible.  Start the XP that you have installed.  Then copy all your data from the original Windows folder to an external drive or a DVD.

  Then, to try to make this repair, boot from the XP disc and select the recovery option.  This will start you in the recovery console prompt.  From there, you can then run the commands to replace the sam file.  Mike - Engineer Support Microsoft Answers
  Visit our Microsoft answers feedback Forum and let us know what you think.

• HP dv6000 will not perform start up

  OK I turned off laptop went to bed got up to 6 hours went to turn on the unit, but all what he would do is lights come on cd-rom made a noise, lights flash system turns off. Sometimes it is just blinks and turns off. but no matter which it does, the cd-rom will make the noise like when you do not start, and then sometimes it will turn on cd-rom makes noise, opens the cd drawer and flashes then Stern out of battery tested is well below receiver power am the connection of 120 volts and its wide, this unit is equipped with vista with the latest service pack , max 2gig memory and worked fine 6 hours earlier.   a business tech just a want to say that it could be the power supply? So how much is it to replace. I have high mechanical capacities and have built several computers desktop from scratch. Please help as I need for my business and sales on ebay. Thank you jay

  HOW TO FIX YOUR DV6000/DV9000/DV2000

  All the problems described in the previous posts are graphics related...
  Defective Nvidia chip... Intel and AMD based motherboards... Although it is most common on the AMD...

  The symptoms of the computer laptop turn on/off and cutting repeatedly... Or... Turn on/off and having no video... Or... Power strip lights, beeps, stops... Or... No power at all... Or... Intermittent Wireless and video Goes in and Out/Touchpad loss slows and freezes...

  To resolve this problem, you must redistribute the graphics chip.

  I explain in Full detail regarding the good method below.

  Video chip reflow instructions HP DV2000/DV6000/DV9000 Compaq v2000

  First step is full of parts and components dismantling...
  Remove RAM, CPU remove, of course remove radiator and fan.

  Next step is isolating the motherboard... You need for area protect the processor, RAM, hood no port of Cap plastic.

  Try to leave the area of 1/4 inch around the edge of the chip without insulation.

  To isolate the Council... I use thick pieces of Tin/aluminium, you can bend aluminum foil (tin foil) on 4 thick folds...

  Now that you have your motherboard isolated... Do nothing flammable or flammable below the motherboard there course... it will get very warm below.

  You will need a heat gun... You can get them at your Local home improvement store, they cost about $15 - $30... You will use ONLY the LOW setting... I REPEAT... USE ONLY THE LOW SETTING...

  You must then some coins... Yes the coins...
  8 quarters and Nickels 2... Putting Nickels on the bottom 2 and quarter-stack on top...
  Place the stack of 2 Nickels and 8 quarters on top of the graphics chip...

  The reason to use parts: parts serves a few purposes...
  (1) it helps transfers heat slowly in the chip more evenly.
  (2) it helps maintain the heat over a long time/Then helps cool more slow
  (3) give the right amount of weight and should be supported on the chip

  One thing to pay attention to the...

  Hewlett Packard is nutorious for the use of epoxy RED around the edge of the graphics chip... This epoxy coating is used to help secure the chip on the motherboard...
  It is a process that is made in-house by hand... And some boards will have only a little amount of this, some will be have a lot of it... And some are only made on the corner of edges...

  If there is a lot of this on your chip, you could end Up requiring to carefully (REAL CAREFULLY) remove as much of the epoxy as capable of... You can use a razor blade to lightly scrape this Off... NOT TO BE MISSED AND SCRATCH THE MOTHERBOARD! Go SLOWLY...

  Now comes the chip heating...

  Start with the heat gun about 6 inches from the top of the stack of quarter... You want to be holding the gun at a 45% angle... Aiming heat at the edge of the chip, you will start turning around the chip - around the outer edge of the chip... then use circles more tight focusing on the battery of the watch, and then after about 30-40 seconds, slowly move closer to the chip...
  Never move the Heat Gun more near the top edge of the battery of your room... Then he pull back and repeat slowly. The chip must become hot enough to melt the solder balls on the underside of the graphics chip down the pads of Contact on the motherboard... and it takes quite a lot of heating to... Do not OVERHEAT the chip... It's better for her Underheat and have to redo... than to the overheating... This will cause the weld to break towards the low and even crack/split... the original failure forever...
  This process will take about 3 minutes total. Once you cut your heat gun... Leave the pieces on the chip stack and let sit for another 5 minutes...

  Now remove the corners (carefull, they might still be hot)
  Remove all insulation... Reinstall the RAM, CPU, heatsink and fan (and of course heat Pads or stick...) Note:. If the dough is used... It takes the dough of money...

  Now you can connect the power button bar / video cable and the DC Jack cable... And taken AC adapter... You are now ready to Test the video and solid food...

• Windows Vista will not complete start up

  Help

  me

  cant

  beginning

  Hello

  1st thing to try is a restoration of the system in safe mode

  http://www.windowsvistauserguide.com/system_restore.htm

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode option with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

  If that does not read this information

  the link below is how to download and get a vista disk startup repair, which you can start from the

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  Here's how to use startup repair system restore command prompt, etc. to bleepingcomputers link below

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  to boot from the dvd drive to be able to you will see a way to get into the bios Setup at the bottom of the screen or command menu start

  It would be F2 or delete etc to enter the BIOS or F12 etc. for the start menu

  Change boot order it do dvd drive 1st in the boot order

  http://helpdeskgeek.com/how-to/change-boot-order-XP-Vista/

  and if all else fails and you need to reinstall vista are the normal methods for computers preinstalled vista portable

  Contact the computer manufacturer and ask them to send vista recovery discs

  they do it for a nominal cost of $

  also ask them if you have a recovery partition on your hard drive to get back to the way you bought

  you would normally press F10 or F11 or Alt + F10, 0 at startup to start the recovery process according to the manufacturer

  Ask them of the exact key sequence

• runtime error will not firefox start

  I have Firefox 3.6
  Whenever I try to open the browser, I get an error message that says: Runtime Error!
  Program: C:\Program Files (x 86) \Mozilla Firefox\firefox.exe

  This application has requested the execution to terminate in an unusual way. For more information, contact the application support tema.

  Is it possible that you can help me with this situation?

  Start Firefox in Firefox to solve the issues in Safe Mode to check if one of the Add-ons is the cause of the problem (switch to the DEFAULT theme: Tools > Modules > themes).

  • Makes no changes on the start safe mode window.

  See:

  • Troubleshoot extensions, themes, and issues of hardware acceleration to resolve common problems of Firefox
  • Solve problems with plugins like Flash or Java to solve the common problems of Firefox

  If this does not work in mode without failure, then disable all extensions and then try to find out who is the cause by allowing both the problem reappears.

  • Choose "Disable all add-ons" on issues to troubleshoot Firefox in Safe Mode to set window to disable all extensions.
  • Close and restart Firefox after each change through "file > exit ' (Mac: ' Firefox > leave";) Linux: "file > exit ')

• II-think ME214 will not go start page and surveys through the process on when I touch the screen, but used to progress beyond this point

  I have a ME214 ii - think she returned to Chinese writing it starts and get to first page once I touch screen that it queries through the start-up process each time. Also when I connect to the computer it not of resistances that it is a device on the computer. He information in the manual that there is a reset on the side button but I can't find a someone out there could provide some answers please

  Hi Stanley_50,

  ·         He has already worked?

  ·         Did you do changes on the computer before the show?

  ·         What is the exact make and model of the unit?

  Run the fixit of the article.

  Hardware devices do not work or are not detected in Windows

  You can contact the manufacturer of the device to reset the key.

• LR6 will not automatically start when the memory card is inserted

  Hello

  Recently upgraded to LR6 from LR 5.7.1. When LR 5.7.1 was installed, it would automatically start when the memory card is inserted. With only LR6 installed it does not open when the memory card has been inserted.

  I "see the import dialog when a memory card is detected."

  I have LR installed 6.0.1.

  When the memory card is inserted, you receive the following error message:

  

  If I right click on the disk memory and select Auto Open play, a list of programs appear particularly LR. The program is highlighted is

  

  If I click on LR in the list above, I encounter error "Application not found".

  When I manually start LR6, it works and I can manually import from memory card.

  What can I do to fix this?

  Thank you

  Stu

  Yes, Autoplay is still trying to run LR5.

  There is a previous thread with notes on how to edit the Windows registry to resolve this problem, if you are comfortable doing.

• Print Spooler service will not be "started."

  Running WinXP Pro with all the latest updates.  The Print Spooler Service continues to stop on its own.  Ran a repair twice installation and that seems to fix the problem for a while.  But the print spooler service continues to shut down.  Do not know why.

  Run the hp print diagnostic utility to fix it to the top.
  http://h10025.www1.HP.com/ewfrf/wc/document?DocName=c02072599&LC=en&cc=us&DLC=en

• Update for Windows XP (KB2509553) security will not install starts but will not end

  Update for Windows XP (KB2509553) security is not installed

  Hi RogerGreene,

  1. Did you the latest changes on the computer?
  2. You are able to install some other updates on the computer?
  3. You have security software installed on the computer?
  4. You receive an error message when you try to install the update?

  Method 1

  I suggest that you manually download and install the update, check if it installs properly.

  Update security for Windows XP (KB2509553)

  http://www.Microsoft.com/download/en/details.aspx?displaylang=en&ID=16350

  Method 2

  If the previous step fails then I would suggest that reset you the Windows Update components by default and then try to install the update.

  How to reset the Windows Update components?

  http://support.Microsoft.com/kb/971058

• When I put a cd in the drive it will not automatically start and if I type in what he tells me sub run an always pop error and I can't to start

  Whent to repair it for me and it did not help

  Please click on the link below and follow the steps on the page:

  http://www.WikiHow.com/configure-CD-and-DVD-AutoPlay-in-Windows-XP

  MD MOEEN AJAZ KHAN - MCP, N +, A +.

• Will not cross 'Start Sync' with creative cloud?

  I am trying to sync my creative cloud with my computer, but it doesn't load for some time and then is to say 'Start Sync '. I rebooted everything and yes I have the desktop version of CC. What should I do? I want my creative cloud like a folder on my computer (macbook pro).

  Ah, I managed to make it work by uninstalling the desktop app and install again. For those who have the same problem.