Windows could not parse or process unattend answer file

Similar Questions

• PC with Windows Vista does not restart after installing updates, "Windows could not start...". "File:\Windows\system\winload.exe status: Oxcoooooof.

  Last night, I installed Windows updates on my HP Pavilion dv6227cl and now Windows will not boot.  I get the message "cannot start Windows.  A recent hardware or software change might be the cause.  File:\Windows\system\winload.exe status: Oxcoooooof Info: the selected entry could not be loaded because the application is missing or damaged.  I DO NOT have the Windows Setup disc.

  Hello

  I suggest you borrow the CD of windows vista to your friends

  Method 1:

  Step 1:

  I suggest you check in safe mode.

  Start your computer in safe mode

  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  Step 2:

  If you be able to start your computer in safe mode, I'd say make clean boot and check.

  Place the computer in a clean boot state, then check if it helps. You can start Windows by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: After troubleshooting, make sure the computer to start as usual as mentioned in step 7 in the above article.

  Method 2:

  I also suggest you to see link and check.

  Error: Windows could not start. A recent hardware or software change might have caused the problem after installing Windows updates

  http://support.Microsoft.com/kb/2674065

• Windows could not start. Status: 0xc000225. File: \Boot\BCD

  Pavilion dv7 - 6187cl Entertainment PC

  Hello

  The following assumes that you are using Windows 7

  If you do not, use another PC to create a Windows 7 recovery CD.  Download the ISO relevant among the links below.

  Windows 7 32 bit

  Windows 7 64 bit

  You must use an app like ImgBurn to burn the ISO to a CD - a guide on the use of ImgBurn to write an ISO on a disc is here.  One time created, or if you already have this, insert the CD into the laptop and restart at the start of it.  Select repair your computer and choose the command prompt.  When this charge, enter the following commands and press on enter after everyone – including spaces as shown.

  Bootrec.exe

  bcdedit/export C:\BCD_Backup

  c:

  Boot CD

  BCD attrib s h - r

  Ren c:\boot\bcd BCD.old

  Bootrec /RebuildBcd

  Bootrec /fixmbr

  Bootrec /fixboot

  Remove the rescue CD and try to restart the laptop.

  Kind regards

  DP - K

• Windows could not start the service audio windows on the local computer. Error 1067: The process is completed in an unexpected way!

  Please help me! ....
  Audio service does not
  I tried Services.msc and tried starting windows Audio...
  The following error has come!
  Windows could not start the service audio windows on the local computer. Error 1067: The process is completed in an unexpected way!
  There is a sign of X in the audio icon...
  and when I click on this audio icon... TROUBLESHOOTER OPENS...
  all this happened all of a sudden!
  Please help me!
  Thank you.
  Nischal Sp

  Please provide the error screenshot more better assitance. Also, try this:

  Try to copy and merge the audio from another Windows 8 or better service.

  You can do this by going to the Registry Editor (make sure that the other computer is also a 32-bit system)

  Go to HKLM/system/current control set/services/audiosrv click audiosrv and then on the file menu, select export and save the file to a USB key or drive.

  While copy on your machine and merge. Then restart your system.

  Otherwise reset Windows 8:

  http://www.kapilarya.com/how-to-reset-Windows-8

  Good luck once again :)

• "Windows could not complete the installation", Y510P

  Hello

  Just got my new Y510P and realized it's impossible to start Windows.

  Initially it displays error "Windows cannot parse or process Unattend...» [... \unattend.xml] [oobeSystem] pass... »

  After reboot he start to display a different message - "Windows could not complete installation, restart the installation.

  The operating system is Windows 8.1.

  Looks like I'm not the only person having this problem. System recovery does not help, of course (as well as the graceful Lenovo tech support).

  I think that the problem caused by the incorrect unattend.xml file that fails to install any software because of this error and unnesessary blocking Windows to complete the installation.

  I see no other way rather than installing Windows from another source. I don't want to pay for another Windows license and instead return the Lenovo laptop, but perhaps there is another way?

  Problem solved.

  I contacted Lenovo support and they offered me to send recovery discs I received a few days later. I installed the cleaning system of records and have not experienced any problems since.

  I'm still not fully satisfied because I cannot reset the laptop to the factory settings without these discs, but I think I can live with that.

• Windows could not find a certificate to log on the network

  So I try to connect to the network that appears, and then trying to connect but it with "Windows could not find a certificate to log on the network. Now, I tried unchecking security in the properties box and also to uncheck it to 'use windows to configure my wireless network.

  NONE OF THESE WORK FOR ME!
  Also attempted to fix the network, but he says that "windows could not finish repairing the problem because it is impossible to perform the following action: connect to the wireless network '"
  I am currently under SP2, but in the process of installing SP3.
  Help!

  This error usually occurs because you have specified a connection protocol 802. 1 x.  You must configure your properties to uncheck this box.  See the following article:

  "Windows could not find a certificate to log on the network.

  <>http://answers.Microsoft.com/en-us/Windows/Forum/windows_xp-Networking/window-was-unable-to-finad-a-certificate-to-log/f68d2ea6-51c4-4B86-a5de-da4d06afb50a >

  HTH,
  JW

• Backup files Vista - "Windows could not find any backup sets [file path]."

  I have a Vista computer.  The hard drive broke so until I replaced it I backed up all the files on the computer to another computer running Windows 7. I did it in the backup and Restore Center.  I made a backup of files, not a full backup of the system (I've seen the full backup of the system mentioned in other posts, but that was not an option... maybe which is only available on Vista Premium).  In any case, I replaced the hard drive and then try to restore the files, but I get the message "Windows could not find any backup sets [file path]."  Anyone have any ideas?  Thank you.

  Here is an article on the restore procedure:http://www.vista4beginners.com/How-to-restore-files to make sure you do this right.  It's a selective restore of a full or selective backup (not a full restore from a full backup) - but since you did a full backup, it matches your process more closely than would a full restore.

  Here is an article on the advanced use of restoration (during normal restore does not work):http://www.mayankraichura.com/post/2009/08/06/Avdvanced-Restore-via-Windows-Vista-Backup-and-Restore-Center.aspx.

  Restore files from a backup
  http://Windows.Microsoft.com/en-us/Windows-Vista/restore-files-from-a-backup

  Back up and restore: frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows-Vista/back-up-and-restore-frequently-asked-questions

  I also found the following (but don't know if it of true or not):

  1. after the start of "backup and Restore Center."

  2. I chose "Advanced Restore"

  3. I was did not an administrator password... maybe because my account is an administrator account.

  4 choose "files from a backup made on a different computer.

  5. in the dialog box indicating "Select the location of the backup to restore", select "hard drive, CD or DVD...". »

  6. under the drop-down list box, select your drive/partition and continue

  7. If all the backups on your drive, it will show a list of them.

  8. in my case, he showed a backup, but in the backup location, it will show "backup location is not available."

  9. I was frustrated, but then I somehow just select this backup (Yes... even if he said that thebackup location is not available " ")

  10. and you press "next".

  11 guess what... no error!

  12. a window appeared asking me if I wanted to do a full restore, or I want to select specific folders or files.

  13. I selected the folders I wanted to restore and bingo... it their restored smoothly.

  14. so that the next time see a mistake, try to continue with him... ;)

  I don't know if this will help, but it does not provide much information about the process (when it works).  I hope you find any error or discrepancy in your procedure and it will clear up and allow you to restore.

  I hope this helps.

  Good luck!
  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Windows could not start on Satellite L510

  HI :)

  I'm not very tech savvy, I've only had my laptop a month. And yesterday, when I turned it back on I got this message...

  Windows could not start. A recent hardware or software change might be the cause. To solve the problem: Insert your windows installation disc, and then restart your computer
  If you do not have the disk, contact your manufacturer computer or system administration.

  file: \boot\bcd
  status: 0x000000f
  Info: an error occurred trying to read the boot configuration

  I have been all over these forums and the internet looking for a solution, but no luck. It's the weekend, so I can not communicate with the service line.
  I would appreciate a process step by step what it is, that I need to download or reset. I do not have the windows installation disc, because it did not come with my laptop.

  I really appreciate your help in advance ;)

  Hello

  Well, the error message says everything to me. Insert the Windows disk * or * contact manufacturing (Toshiba). ;)

  By the way: it would be interesting to know if you can boot into safe mode. Check it!
  If so, you may start the HARD drive recovery. Therefore, select Repair my computer in the Advanced Start menu and follow the instructions on the screen.

  Yes, with the laptop didn't come a disc, but you can create one!
  Please read the operating manual always first.

  Now it s too late to create such a floppy, but you can order directly into a new Toshiba:
  https://backupmedia.Toshiba.EU/landing.aspx

• error on Windows 2008 server std edition "Windows could not update the Configuration to start the computer. Installation cannot continue. "

  I try to install windows 2008 server std edition on HP DL 380 G5 server, I am getting error while installing "Windows could not update the Configuration to start the computer. Installation cannot continue. ", please suggest?

  I tried also with HP smartstart CD, but failed.

  Thanks guys, I found the answer to my question, I used the last HP smart Start CD (V8.70B for windows 2008 server X 64) for DL380g5 for windows 2008 server STD, and it worked fine.

  For the Smart Start CD list visit: http://h20000.www2.hp.com/bizsupport/TechSupport/DriverDownload.jsp?prodNameId=344318&lang=en&cc=nl&taskId=135&prodTypeId=18964&prodSeriesId=345557
  Thank you...

• Windows could not search for new updates. Code 80072EE2

  First, some background...

  I am running Windows Server 2008 / Hyper-V

  I have a Vista OS guest I have loaded from a base image (vhd)

  I also have a Server 2008 guest OS also loaded from a base image

  These images have not been created on this machine.

  I had guest OS installed since the XP CD but since she departed.

  The machine on which it is all performed has a 2.93 GHz Intel Core 2 X 6800 processor.

  8 GB DDR2 RAM

  I've had this problem for several weeks now.  At the beginning I could not the host OS to run updates, it would fail with an error 80072EFE code. This is for several weeks. Finally, while researching this problem I came across an entry mentioning only the BITS required to run so double I checked it. Of course, it was off. I started the service and that fixed the problem with the host operating system and apparently the problems she was having with other sites.

  So I think big is issues with the Vista and the comments of 2008 operating system. No luck, these systems still will not run updates.  The 2008 operating system returns an error "Windows could not search for updates" with a code error 80072EE2

  I tried several solutions to this problem, and at least twice have reloaded the base images because I mucked in the system so much that I lost track of all the changes I had made to the OS.

  I ran these commands...

  regsvr32 /s c:\windows\system32\wuapi.dll
  regsvr32 /s wuaueng1.dll
  regsvr32 /s c:\windows\system32\wuaueng.dll
  regsvr32 /s c:\windows\system32\dllcache\wucltui.dll
  regsvr32 /s wups2.dll
  regsvr32 /s c:\windows\system32\wups.dll
  regsvr32 /s wuweb.dll

  I also tried the procedure found here...

  http://social.answers.Microsoft.com/forums/en-SG/vistawu/thread/6511a332-7de3-4F10-B823-49b6dae86b9c

  Which loads a new "TrustedInstaller.exe" in the folder "C:\windows\Servicing\".

  And on the Vista operating system I also tried this...

  http://support.Microsoft.com/kb/971058

  By clicking on the "Fix It" link.

  It still does not.

  Oddly if that I'm typing this I had rebooted the OS Vista and restart it it notafied me that he was installing updates 1 of 3. However when it finished I tried to check the updates and it gives me the same error "Windows can not find updates" with a code error 80072EE2.

  Someone at - he found an answer to this question. I ask because I'm looking for what I see many people with the same issue.

  You may encounter temporary connection errors [e.g., 80072EE2] when you use Windows Update or Microsoft Update to install updates
  http://support.Microsoft.com/kb/836941 ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• Having a problem with the update of the window. He said that windows could not search for new updates. It's the found error 80245003 code

  Having a problem with the update of the window. He said that windows could not search for new updates. It's the found error 80245003 code

  Take a look at this article as it addresses this error code. Mike - Engineer Support Microsoft Answers
  Visit our Microsoft answers feedback Forum and let us know what you think.

• I have error #1053 windows could not start the printer spooler. Help

  Windows could not start the printer spooler. I received the error #1053.
  whatever it is sent to the printer never finished loading and crashes to the top
  my computer, so I have to re - start.

  This forum is for posting comments on the web site of Microsoft Answers, is not for technical questions.  Ask your questions to http://answers.microsoft.com/en-us/windows/forum/hardware, making sure that you specify your Windows version in the drop-down lists at the top.

• error message: "windows could not find a certificate to connect to the network.

  My NetGear wireless icon shows this error message "windows could not find a certificate to connect to the network.

  Hello

  Did you change your computer before this problem?

  You can follow the procedure in the article.

  Unable to connect to the network: Validation and certificate in Windows XP and Vista errors

  http://KB.NETGEAR.com/app/answers/detail/A_ID/7334/~/unable-to-connect-to-network%3A-validation-and-certificate-errors-in-Windows-XP

  Alternatively, you can contact Netgear support to improve assistance in this regard.

  Welcome to the NETGEAR support

  http://support.NETGEAR.com/

• update of Windows, "Windows could not search for new updates", "mistake Found; WindowsUpdate_80080005 ".

  I try to run windows update and continue to receive the same message:

  "Windows could not search for new updates", "mistake Found; WindowsUpdate_80080005 ".

  When I try to display the windows Explorer update history shows only a white screen with an 'OK' button at the bottom right

  When I click 'OK' the screens of pointer, the computer works, but the screen remains blank until I have completed the task in the Task Manager.  I've updated from windows to the request automatically to the daily updates.  I get the same update for my Kodak printer, which is also a place for the wrong model.  This leads me to believe it was not working properly.

  any suggestions?

  I am running Kapersky "Antivirus 2009"

  OS: Windows Vista Home Basic

  My notes.

  0 x 80080005 implies that Microsoft Installer is not configured correctly or it may have malfunctioned.

  Run the Startup Repair tool by using the Windows Vista installation disc

  1. Insert the installation disc.
  Note: The computer must be configured to start from a CD or a DVD. For more information on the configuration of the computer to start from a CD or a DVD, see the documentation provided with your computer.

  2 restart the computer. To do this, click Start, click the arrow next to the lock button, and then click restart.
  Note: If you cannot restart the computer by using this method, use the power button to turn off the computer. Then, turn the computer back on.

  3. set your preferred language and then click Next.
  Note: In most cases, the Startup Repair process starts automatically, and you do not have to select in the System Recovery Options menu.

  4. click on repair your computer.

  5. in the System Recovery Options dialog box, click the operating system you want to repair, and then click Next.

  6. in the System Recovery Options menu, click Startup Repair to start the repair process.

  7. when the repair process is complete, click Finish.

  To run the Startup Repair tool if the computer has preinstalled recovery options

  Note: In most cases, the Startup Repair process starts automatically. Follow these steps only if the Startup Repair tool does not start automatically.

  8. remove all floppy disks, CDs and DVDs from the computer and restart the computer.

  9. follow one of these steps:

  (a) if the computer has a single operating system installed, press and hold the F8 key in restarting the computer. You must press the F8 key before the Windows logo appears. If the Windows logo appears, you must restart and try again.

  (b) if the computer has more than one operating system, use the arrow keys to select the operating system you want to repair. Then, press and hold F8.

  10. in the Advanced Startup Options, use the arrow keys to select repair your computerand press ENTER.

  11. click on a layout of keyboard in the list and then click Next.

  12. click on a user name in the list, enter the password and then click OK.

  13. in the System Recovery Options menu, click Startup Repair.

  14. when the repair process is completed, click Finish.

  TaurArian [MVP] 2005-2010 - Update Services

• Windows Vista - after the RESTORE partition HARD drive: WINDOWS COULD NOT COMPLETE the INSTALLATION. TO INSTALL WINDOWS ON THIS COMPUTER, RESTART THE INSTALLATION

  Hello

  I have WINDOWS VISTA and just tried to reinstall my laptop of restoration on a HARD disk partition.

  The restore went through, but then I got the error: WINDOWS COULD NOT COMPLETE the INSTALLATION. TO INSTALL WINDOWS ON THIS COMPUTER, RESTART THE INSTALLATION

  When I press 'OK' (which is the only option), it tries to start again, until I get the same error through the black screen.

  How can I get out of this loop please?

  Thank you.

  Lucie

  Hello

  For any problem with the help of the recovery Partition that has been copied to the hard disk by the computer manufacturer, you must contact them.

  This recovery process is the manufacturer, not Microsoft.

  ________________________________________________

  You never told us why you wanted to do a restore. If you had serious errors and the recovery process does not work, you will have hardware problems. BUT we're only guessing at this stage due to lack of information to help you.

  See you soon.