Windows folder disappears after redirection to another drive

Similar Questions

• Windows XP hangs after installing the new drive hard & software

  My 20 GB hard drive was almost full and the computer (Dell GX240) has been slow, I installed a new 160 GB drive. After loading Windows XP, Linksys, McAfee, MS Office and MS Windows updates would crash randomly. Restart the system would allow him to run for a few minutes and then hang again.
  I reformatted the drive and partitioned to 80 GB and then reloaded all programs above with the same results.
  I reformatted back to 20 GB, loaded XP and Linksys and the same problem occurred.
  It seems that the internet has something to do with the problem.
  Any suggestions?

  "Wingnut555" wrote in message News: 6aac2f2a-ffb6-4a22-98e1-67417709eb6b...

  The drive of 20 GB that I removed to install the largest capacity disk has been reinstalled after the failure of a larger. I am currently running on the same pc and the old drive. I have another drive of 20 GB that had XP installed on it earlier. Thinking that I might try that one that I started to load some of my other programs operating and when I installed Office 2007 for household use and selected updates online blocked system shortly after. The problem is therefore not only on new facilities. The reader that I use currently a Office 2007 is installed and it works fine.

  What is the largest disk that will handle XP? I heard it's 137 GB, is it true? If I can make it work how would you recommend I have partition the drive of 160 GB?

  Thank you

  XP can handle drives of 1 TB to NTFS without problem - it's the motherboard on computers more elders who may have problems, that it is not compatible LBA.
  There is really no need to partition the disk, but I would tend to opt for about 60 GB for the operating system and 100 GB of data and then move the folder My Documents (using the option in its properties) of the data partition. This allows to separate the data and programs and means a lot less work if a reinstall is needed.
  
  --

  Noel Paton | Nil Carborundum Illegitemi | CrashFixPC | The lazy three fingers

• Windows store disappeared after trying to download Windows 8.1

  My Windows store disappeared afater trying to download Windows 8.1! Then it is!  Since I have to go to download the free Windows 8.1 where do I find

  As I continued to try to download and install Windows 8.1 I finally received this message: "you're running a business or volume license of Windows 8 and cannot be updated using Windows Store.»  Contact your system administrator for more information on how you [date of your PC to the Windows 8.1

  I also had another message that he does not meet the minimum requirements and I really don't think that's true.  It is a fairly new Toshiba laptop running Windows 8 with 6 GB of memory and a 500 GB hard drive, which, as well as other info should accommodate 8.1.

  And I can't really the absence of Windows store, as I used it.

  Help, help, help!

  Hi Pauline,

  Thanks for posting your query on the Microsoft Community.

  I understand that you are facing problems trying to upgrade to 8.1 Windows in your system.

  To solve your problem better, kindly provide us with more details

  1. You use Windows 8 Enterprise version or Volume license key in your system?

  I suggest you follow the below methods of troubleshooting for Windows App Store in your system:

  Method 1: you can try to reset the application cache.

  1. Press the Windows key + R to open the run window.
  2. Type wsreset.exe.
  3. Press OK.

  Method 2:

  If the problem persists, run DISM.

  Corruption of Windows errors can prevent service packs and updates for Windows Installer. For example, an update can not install if a system file is damaged. The DISM tool / system update can help you to correct certain errors of corruption of Windows.

  Follow the steps in the link below to run TELLM:

  https://support.Microsoft.com/en-us/KB/947821

  Answer with the information needed to help you solve the problem. I'll be happy to help you.

  Thank you.

• Of Mini Windows taskbar disappear after closing one - boring!

  When I have several emails open outlook and I want to quickly close a whole bunch of them I want to be able to close the mini window.  However after the closure of each of them by clicking on the red x, the set of mini windows disappears and I have to move the mouse down to the button of the taskbar for the mini windows reappear and then I can close one that follows and then repeat again and again.  It is very annoying when you have a dozen or so open emails.   How can I make other minis windows stay on the screen, so I can just click each red x one by one, without returning to the task between the two bar button?  It would be so much faster.

  Thank you

  Hello

  ·         What is this happens only with windows Outlook?

  Step 1:

  Open multiple Internet Explorer Windows, and then try to close them by using Windows Ridge previews.

  Step 2:

  Try restarting in a clean boot to see if you are able to close previews without collapsing the list every time.

  http://support.Microsoft.com/kb/929135/en-us

  Note: When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  Click Start, type msconfig.exe in the start search box and press ENTER.

  If you are prompted for an administrator password or for confirmation, type your password, or click on continue. On the general tab, click the Normal startup option, and then click OK.

  When you are prompted to restart the computer, click on restart.

• Windows apps disappear after update 8.1 automatic windows and keyboard do not work on the internet

  I've had my Toshiba Satellite for 2 months, but after the automatic update of the Windows apps disappear and the keyboard does not work when I go online (I can type when I connect as a guest, but I can't type as an administrator).

  Can someone help me, in steps (I'm not a computer wizzard).

  Alexander of Amsterdam

  Hi Alexander,.

  Thanks for posting your query on the Microsoft Community.

  Thank you for details on the issue. That your applications Windows disappears, I suggest you follow the methods below:

  Method 1: Troubleshooting applications.

  The apps store can automatically detect and fix any incorrect settings or errors that could cause problems with applications.

  Refer to the article below and try the steps in it.

  http://Windows.Microsoft.com/en-us/Windows-8/what-troubleshoot-problems-app

  If the issue still persist, then follow the method below.

  Method 2: I suggest you to check if the applications have been successfully updated. See the procedure to check the updates below:

  a. press Windows + C keys in the app store for Windows.

  b. click on settings and then click App updates.

  c. click Check for updates and install available updates.

  If the issue still persist, then follow the method below.

  Method 3: Follow the steps below to give permissions to All THE APPLICATION PACKAGES.

  a. go to Program Files (make sure that "hidden files and folders is on").

  b. right-click on WindowsApps and go to Properties > Security tab > Advanced.

  c. click on continue to display object permissions.

  d. for the owner, it will show TrustedInstaller, click on change.

  e. a new window will open to certain Types of objects > select groups , and then click Ok.

  f. in the text box below to type All THE APPLICATION PACKAGES.

  g. press Ok and restart your system.

  Hope this information is useful. Let us know if you need more help, we will be happy to help you.

  Thank you.

• Windows 8 license after replacing the HARD drive

  Original title: change of equipment (HARD drive)

  Good night, I have a computer laptop windows 8 and I fear that the HARD drive (malfunction) he'll need replacement.

  My question is, what will happen to my windows 8 license, once my current HARD drive stop working (because the key is encrypted in the bios)?  
  Please note that in the country where I live customer support is, at best, ineffective, so personal attention is not an option.
  Thank you before hand.
  Send you my best regards.

  Hi, Caesar,

  Activation pairs your product key in your hardware configuration and helps to verify that your copy of Windows is not been used on more computers than to allow the 3668Microsoft Software License Terms.

  If you change the hardware on your PC, you must contact support to activate Windows by phone.

  As you have decided to replace the hard drive, you could face an activation/Windows not genuine error.  You can follow these steps to make a phone activation.

  a. press Windows key + X , then click run, then type: slui.exe 4

  b. press the ENTER key

  c. Select your country from the list.

  d. choose telephone activation .

  e. stay on the phone (do not select/press all options) and wait for a person to help you with the activation.

  f. explain your problem to the support person

  See the article:
  How to activate a Microsoft product using Microsoft Product Activation Center

  http://support.Microsoft.com/kb/950929/en-us

  In addition, refer to this topic:
  http://answers.Microsoft.com/en-us/Windows/Forum/windows_8-windows_install/hardware-changes-no-more-activations-available/ed283ad6-D462-478f-a1a0-8922226ce82b

  Hope this information helps.  If you have any other questions, we would be happy to help you.

• Partition Windows 10 disappeared after the installation of El Capitan

  @Loner T - seems you have helped others on this question and hope you can help me through it too.  I have a MBP early in 2013 with a 500 GB SSD.  I allowed the upgrade to El Capitan, and like others, this is the boot camp partition disappear.   Holding the option key pressed when starting displays only the ability to boot into OS X.  Here's what I've done so far:

  -SIP is disabled.  Confirmed after restarting normally by typing csrutil status

  -Tried to do the other bootable partition using your instructions on

  -fdisk/dev/disk0-e

  -Pei

  -setpid 4

  -07

  -Pavilion 4

  -Pei

  -w

  -y

  After resigning, I restarted and press option.  Windows now appears when I press and hold option, but when selecting it I get the error "Missing Operating System".

  Here is the result of all other orders:

  diskutil list gives:

  / dev/disk0 (internal, physical):

  #: NAME SIZE TYPE IDENTIFIER

  0: GUID_partition_scheme * GB 500,3 disk0

  1: disk0s1 EFI EFI 209.7 MB

  2: Apple_CoreStorage Macintosh HD 300.0 GB disk0s2

  3: disk0s3 Apple_Boot Recovery 650.0 MB HD

  4: Microsoft database 101,0 GB disk0s4

  / dev/disk1 (internal, virtual):

  #: NAME SIZE TYPE IDENTIFIER

  0: Apple_HFS Macintosh HD GB + 299,6 disk1

  Logical volume on disk0s2

  DAED883D-1E3E-48A7-A986-A2C2E5483BE7

  Unencrypted

  CS-diskutil list displays

  

  TPG - vv - r see the/dev/disk0 poster:

  

  sudo fdisk/dev/disk0 gives:

  
  

  
  

  I think all this means I have a lost partition as you described to others.  I downloaded Testdisk and gdisk.  Output of TestDisk:

  

  Run a quick scan on drive Test and see these unrecoverable partitions (stupid question this mean that they are lost for good or they are good and that they need not be recovered?) 。

  

  Prosecutor:

  

  Product selection P here:

  

  These are the values that I can use in steps 7 and 8 in this post?

  
  

  Step 7-587618304

  Step 8- + 388564992

  In the first series of markets Gdisk. The second set of rebuild MBR is the same for a standard installation of BC.

• Files in a folder disappeared after the installation of the software for Word color card.

  I have files in a folder that has disappeared from my office, I think it happened after the installation, I think it happened after the installation of the software for wordcard

  OT: I keep files in a folder that has disappeared from my office, I think it happened after the installation, I think it happened after the installation of the software for wordcard color

  Hello

  The problem occurs only with files on the desktop?

  Method 1
  I suggest you try the following steps:

  a. open the Recycle Bin on the desktop.
  b. If you find the folder you need, do a right-click on the file you need and click on restore.

  Method 2
  I suggest you try looking for the missing folder.

  Find a file or folder
  http://Windows.Microsoft.com/en-us/Windows7/find-a-file-or-folder

  Method 3
  I suggest you try the steps from the following link:

  Recover lost or deleted files
  http://Windows.Microsoft.com/en-us/Windows7/recover-lost-or-deleted-files

• Problems with folder permissions after replacing the hard drive

  Hello

  Recently, I replaced the hard drive on my mac.  Already before the replacement, I got the files that I had locked.  Now I'm unable to open the file.  I get the error "the folder 'nom_de_dossier' can not be opened because you don't have permission to see its content".  I looked at the permissions for the folder and everything he says is fetch.  I ran a command in the Terminal and for one of the records in question, that's what I see-

  drwxr-x - 13 501 501 442 5 July 2013 MG

  Any help would be greatly appreciated!

  Running OS X El Capitan

  10.11.4 version

  Try this first:

  Start the mac all holding the SHIFT key, it is slow, connection, and then select Restart from the Apple menu.

  When this does not help:

  Reset password utility in the recovery Partition:

  1. Restart your computer from the recovery partition.
  2. Open disk utility and run a repair permissions on your boot volume (in ElCapitan click the first aid tab). Once this completed, close disk utility. We do this for good measure.
  3. Open a Terminal from the Utilities menu. Type in resetpassword and select your user (NOT administrator system/root) account in the menu drop-down.
  4. Click on the Reset button at the bottom of the window ACL section and Reset the folder permissions.
  5. Exit the utility password and return to the main recovery menu.
  6. On your keyboard, press ⌘ + Q and restart your computer. It is very important that you don't hold down the power button to exit the recovery session, or the ACL Reset to occur.

• Can not recover the Windows 7 desktop after replacing the hard drive

  I bought a new HP Pavillion Elite (HPE-240f) in August 2010. A week ago my hard drive has no SMART short self-test during systematic hardware diagnostics. I installed a new hard drive of the same size - 1 TB and could never make it work properly. I tried the following (in that order).

  1. using a system repair disc, I got the system from a previous image (which I did shortly after the purchase, install my own software and configuration of all). It worked, but then I noticed that Windows Update was not working. I ran various Microsoft diagnostic tools and discovered that some (unspecified) system files have been damaged or missing. All the fixes I tried didn't work. I ran hardware diagnostics extended, but no problem not found.

  2. I tried to restore the system to the default settings by using the original image on the D partition. At first it seemed to work, but at the last moment when the system started, I saw a message on the screen that Setup is starting services and then got a warning saying that services failed because of (unspecified) problems with hardware.

  3. I tried to restore the system from the system recovery discs and a message "system recovery disks do not support this computer."

  4. I found this Cyberlink utility on the HP website, dealing with precisely this issue. I created a CD tried and it didn't work.

  5. I found this document on the HP Web site, saying that if you are replacing a hard drive with sectors of 512 bytes with a new advanced Format (AF) drive (with areas of 4 096 bytes) and your system was manufactured before October 2010 (as mine was), you must get the new HP recovery disks. I thought I finally found the root of my problems (since the new drive is indeed AF and the old man is not) and ordered HP recovery discs.

  6. the disks arrived today, and I noticed that the version number of the software (for Windows 7 version) is almost the same as on the computer, except that the last digit is 9 on disks and 6 on the computer - I guess it's an update to deal with the problem hard drive AF. However, I get 'system recovery disks do not support this computer' error, if I use the utility from CyberLink recovery disks or not. To be on the safe side, I even used a new hard disc (new 1 TB) right out of the box (never partioned and installed previously) and connected the original keyboard supplied with the computer (I also unplugged everything except the monitor, keyboard and mouse). However, I get the same message. Just out of curiosity I tried to put back the original hard drive (certainly not in best shape, even if the system always starts with him) and still could not recover the system.

  What else can I try?

  Any help will be greatly appreciated.

  An alternative to try. > If you can read the Microsoft Windows 7 of 25-character license key attached to the Tower, you can download a Windows 7 ISO file to burn to a DVD. The version must match that on the sticker COST Microsoft. for example Home Premium

   

• Update Windows 10 lost after renewal of HARD drive

  Hi all. I have this laptop V7 482 PG, who has been properly updated for Windows 8.1 W 10 and worked ok until the HARD drive crashed last week. Warranty Acer has worked flawlessly and they quickly returned my laptop with the new HARD drive. So far so good.

  My question is, the operating system is up to 8.1 original after renewal of the HARD drive. Now, when you try to upgrade to W10, MS asks for $299 /-because the free upgrade time.

  What is the solution to this? Buy or Acer this covers too?

  It's free to re - install windows.  Given that you have activated Windows 10, you can evolve again for free using the tool of creation of media.  See the instructions provided by Microsoft.

  https://www.Microsoft.com/en-us/software-download/Windows10/

  

• Taskbar and icons on Windows Vista disappearing after a certain period of time. Why!

  I noticed that if I leave my PC running for an hour or more unattended (even with my screensaver on and the monitor off), that the icons in the taskbar and the desktop will disappear off the screen when I go back and try to use it.  The only thing I can do is to move my mouse and open some things by right-clicking the mouse, but what is it.  I have no other choice than to make a difficult stop (hold the power button until the PC turns off).  If it helps, my PC is a Dell Inspiron 531 that runs on Windows Vista Home Premium 32 - Bit.  At first, I thought it was a problem caused by Internet Explorer 9 (that I have long eliminated from my PC and thankfully returned IE8), but I was wrong.  In addition, my antivirus program is Norton 360, and I run almost religiously to combat ill will on my PC.  If anyone can help me, I would really appreciate it.

  ADD: Also, after the desktop and the taskbar icons disappear when I try to bring up the Task Manager by pressing Ctrl + Alt + Del, the screen goes black and I can just press ESC to return to the white (except for my desktop wallpaper) desktop computer.  Again, any help will be appreciated.

  Hello

  1 did you changes to the software to the computer before the show?

  Start the computer in safe mode and check if the problem is solved or not. If the problem persists not perform the clean boot.

  Was: start the computer in safe mode.

  Safe mode starts Windows with a limited set of files and drivers. Startup programs do not work in safe mode, and only the basic drivers needed to start Windows are installed.

  Start your computer in SafeMode (Windows Vista)

  B: Perform the clean boot

  To help resolve the error and other messages, you can start Windows Vista or Windows 7 by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  Note: perform step 7 to reset the computer to start as usual after the boot process.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  Hope that helps.

• Reinstall Windows Media Center under Windows 7 Ultimate after the new hard drive, installed using Microsft Windows 7 disc

  I had the misfortune I had to replace my hard drive on my Toshiba laptop after reinstalling my Windows 7 Ultimate disc, I find that I am unable

  load the Windows Media Center software. When I click on the location of the file, some files are visible, but it does not load.

  Can I use the disk window to replace or repair the Windows Media Center files without causing other problems?

  Don Winston Hills NSW Australia

  Open your Start menu by pressing the Windows key and type FEATURES in the search box. Select 'Windows turn features on or off ". When the Panel opens, expand the category "Media Features" and place a check in the box "Windows Media Center". You may need to restart after Windows reconfigures itself.

• Unlock windows box disappears after windows automatically locks the screen

  Hello

  I have a professional Windows XP Tablet from Lenovo X 200 ongoing execution machine. This problem does not occur * too * often, but enough to be annoying.

  After 15 minutes of inactiviy, windows is the standard screen saver routine by locking the desktop computer. Meanwhile, the white box that says click on Ctrl-alt-del to enter your password is visible. There is also the virtual keyboard on the screen.

  From time to time, I go back to my computer to see that white box unlock is missing! There is no way for me to go back to windows! I have literally remove the battery and restart. During this time, I lost all my unsaved data... not to mention that I keep not the most graceful way.

  This happened to someone? What in the world could be the cause?

  Thanks for the comments.

  Hi Jim_B_NJ,

  1. you have value to request password on Resume on the computer?

  I suggest that scan you SFC on the computer that would be a system file corrupt on the computer search and replace.

  The analysis may take some time, so be patient. Windows allows to fix corrupt or missing files it finds. If the information of the installation CD is required to fix the problem, you may be asked to insert your Windows XP installation CD.

  For more information please visit the link below.

  Description of Windows XP and Windows Server 2003 System File Checker (Sfc.exe)

  http://support.Microsoft.com/kb/310747

  If you don't want to try windows to ask for the password after the recovery step turn it off below.

  (a) make a right-click on an empty area on the desktop

  (b) select Properties in the context menu that will open

  (c) click the screensaver tab

  (d) uncheck the box that says on Resume, password protect to disable.

  (e) click OK

  If you don't want the window Ctrl + Alt + Del on the logon screen, try the steps below.

  (a) click Start, click run, type Control Userpasswords2, and then press ENTER.
  Note The following dialog box may appear:
  You must be a member of the Administrators group on this computer to open user accounts. You are logged in as username, and this account is not a member of the Administrators group.
  In this condition, you must type the user name and password when you are prompted with the dialog box to type the user name and password of the administrator of the computer.

  (b) click the Advanced tab.

  (c) in the Secure logon section, click to clear the checkbox user must press Ctrl + Alt + Delete if you want to disable the CTRL + ALT + DELETE sequence

  How to enable or disable the CTRL + ALT + DELETE sequence for logging on Windows XP and Windows Vista, Windows 7

  http://support.Microsoft.com/kb/308226

  I hope this helps!

  Halima S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Not able to print the message after redirection to another page of pag current

  Hi Experts,
  
  I'll call you a procedure (who accepts 4 parameters IN) page of the OAF by pressing a button.
  
  My page contains: 4 elements of text Message and the other present button.
  
  I enter values in the 4 message text of introduction of the elements; After clicking on the button submit, he calls with success the procedure.*After by clicking on the button submit, after the call to procedure, I would like to pass on the same page with the values parameter zero and display confirmation message *.
  
  But I am not able to make the parameter null values in the page.
  
  
  I have the code in my page controller below.
  
  REQUEST FORM PROCESS:
  
  OAApplicationModule oa = pageContext.getApplicationModule (webBean);
  
  
  {if (PageContext.GetParameter ("Submit")! = null)}
  CallableStatement call_proc = null;
  try {}
  call_proc = OA.getOADBTransaction () .createCallableStatement ("start oaf_test_tbl_insert_proc(:1,:2,:3,:4,:5); end; ", 5) ;
  call_proc. SetString (1, PageContext.GetParameter ("empno"));
  call_proc. SetString (2, PageContext.GetParameter ("Ename"));
  call_proc. SetString (3, PageContext.GetParameter ('Work'));
  call_proc. SetString (4, PageContext.GetParameter ("Salary"));
  call_proc.registerOutParameter(5,types.varchar);
  call_proc. Execute();
  oa.getOADBTransaction () .commit ();
  
  String message = call_proc.getString (5); out parameter (5) will return a message
  
  
  OAException message = new OAException (message, OAException.CONFIRMATION);
  pageContext.putDialogMessage (message);
  
  pageContext.forwardImmediately ("OA.jsp?page=/practice_test_prc1/oracle/apps/mfg/simplepg/webui/oaf_test_tbl_calling_proc"
  null
  OAWebBeanConstants.KEEP_MENU_CONTEXT
  null
  null
  true
  (null);
  
  } catch (SQLException e) {}
  call_proc. Close();
  }
  
  }
  
  
  Kindly help me, how to print the confirmation message and send to the same page by making the param to null values.

  Hello

  On the successful return of the procedure, you must set a session Variable * (pageContext.putSessionValue ("WFFullListPage") *.)

  Then call it.
  

  pageContext.forwardImmediately ("OA.jsp?page=/practice_test_prc1/oracle/apps/mfg/simplepg/webui/oaf_test_tbl_calling_proc"
  null
  OAWebBeanConstants.KEEP_MENU_CONTEXT
  null
  null
  true
  (null);

  Next, you need to check this condition on the PR of the CO and show the message as required.

  Extract the same value to the controller, as * (pageContext.getSessionValue ("WFFullListPage") *)

  Kind regards
  GYAN