Windows Vista 32 on Netbook MSI, I plug in the power adapter and a few minutes later get blue screen and restarts of netbook.

Similar Questions

• HP Pavilion G6 computer 1093SA laptop does not charge when I plug in the power adapter

  HP Pavilion G6 computer 1093SA laptop does not charge when I plug in the power adapter

  The battery is dead. When I try to turn on the laptop by plugging the AC adapter does not charge or led power LED does not turn on. But when I press the power button, the power, the indicator flashes and turns off (when power adapter connected).

  (1) I tried the press and holding the power button for 30 seconds after removing the battery & AC adapter / CC.

  (2) I tried to change the power adapter too.

  The problem is that it is.

  Your advice is very much appreciated.

  Thank you best regards &,.

  Zia

  Dear customer,

  Welcome and thanks for posting your question on the Forum of Support HP

  It seems that you are not able to turn on the laptop and tried to solve the problem

  Please perform steps listed to find out if it is a hardware or software problem below:

  1. remove all cables and devices, disconnect them and try to turn on the device

  2. check the LED light situation and ensure the action of the spring button / stop is normal

  3 Exchange with a well known power cord and the AC adapter

  4 Pack no adapters are available, check if the power adaptor is slightly warm

  Note: This will give us an indication that the power adapter could be good

  5. do you know if the laptop was in battery or power adapter when you used the last time

  Note: Make sure that there is no spill of liquid or cutting

  6. check if the Port of the AC adaptor is loose/broken

  Note: If the laptop is not on even with a power adapter well known, this confirms the hardware failure with the system board or power DC Circuit

  Hope this helps for other queries to answer the post and feel free to join us again

  * Click on the star of CONGRATULATIONS on the left to say thank you *.

  Make it easier for others to find solutions by checking a response "Accept as Solution" if it solves your problem.

  Thank you

  K N R K

  I work on behalf of HP

• Light remains off after plugging in the power adapter.

  I recently bought a replacement battery for my Toshiba Satellite running Windows XP. I started the new charge battery and removed the computer AC adapter to make sure that the battery was functional. However, when I plug the AC adapter in, the backlight is out.  If I restart Windows, the backlight turns on, but if I disconnect/reconnect the AC adapter, the backlight is turned off again. So, the backlight works, but for some reason, she turns to disconnect the AC adapter.

  Hello Pmorawski,

  Thank you for your message.  It is a Toshiba hardware problem and your question would be better suited for Toshiba.
  See you soon

  Engineer Jason Microsoft Support answers visit our Microsoft answers feedback Forum and let us know what you think.

• HP Pavilion 6500 goes out when the power adapter plugged

  My Pavilion 6500 (specifically dv6623cl) turns off when I plug in the power adapter. If I plug it in, then turn on the laptop, it automaticly turns off before loading windows. If the laptop is already started, and I can plug the power adapter, it immediately turns off. I can charge the battery without any problem, also while the laptop is turned off, but as soon as I turn it on with the adapter plugged it stops, I checked the battery through HP battery check and he said its good, he is holder of a charge very well and everything, the only change made to the laptop hardware wise was an upgrade memory I had no such problems until the upgrade of memory, but I do not see how it would affect the power on the aspect, in order to make a system restore, if ever, I need, the poweradapter must be plugged and theres other system functions that require the adapter complete, it is a question that must be corrected

  any ideads what the problem would be?

  any help is much appreciate

  Thank you, rayandmaura

  Talk to a jury of uselles / forum, do those who seek info on how to reset / bypass the bios password on their (or anyone elses) computer or something as it gets 20 pages of answers, but asking a power / card issue and your luck if you get a response at all,

  I'll just give up to deal with this useless community and just buy 3 extra batteries and remind all of the accused

• I recently our old Windows Vista out of storage, I'm helping with the implementation?

  In fact, I have a series of questions keeping to that, but at the moment my highest priority is to find how to get it all together to the top.

  We had it for 9 years, and during that time my mother was barely used and the only time I ever to remember being able to use would be in 2008 and 2012, but in those moments I was pretty young and I caused internet several related problems. After 2012, you don't really mess with it then, but now that I'm starting to regret buying a mac I recently just to set up our vista.

  I got everything plugged. There is this blue connector Jack (which I assume is the monitor cord) and I connected on the screen where it belongs. There is another string (which I assume is the power cord) and it is plugged, so far, there are only two outlets in the monitor. The computer itself has a cord of black power, the mouse + keyboard cable and the cable from the monitor. Everything is plugged in and well, but after turning the computer and then proceed to turn on the monitor, I get a message that says 'No detected Signal' with three blocks under it, red, blue and green. Am I missing a cord?

  One of the main reasons why I'm doing a switch from my mac to my old windows is due to PaintTool SAI, is available for Vista? And wacom is compatible with vista? It seems to be that some plug-ins to the back of the computer so that it could work. Also, would I be able to upgrade our computer to Windows 7 after setting up?

  If it's a desktop pc, & 9 years old, then you must replace the battery in MB, it controls CMOS (plug & play).

  Simply turn pc off, remove the battery, wait 10 min.replace with the new. Once the pc boot, enter the BIOS, reset

  DateTime, the value for the add-on equipment, set the boot priority, save and exit. Also, read the owner's manual, + all ports

  must have an icon engraved, showing what sound for... A year 9 old pc wouldn't be good, or compatible

  Win 7 run microsofts Win 7 compatibility...

• I want to upgrade to a newer Windows operating system Windows Vista Home Pro 64-bit. What is the recommended procedure?

  * Original title: upgrade

  I want to upgrade to a newer Windows operating system Windows Vista Home Pro 64-bit. What is the recommended procedure? I see that Windows 7 or 8, a free update to Windows 10 is offered. Should I buy 7 or 8 then you spend 10 or just buy 10?

  Thank you

  Jim

  Hello

  Depends on hardware configuration required on later operating systems, and also find out if the manufacturer of the laptop computer is supported and provides drivers for operating systems later as to whether it is possible or feasible to upgrade or not.

  There is no free upgrade Vista to 7, 8.1, or 10.

  Follow these steps before you buy Windows 7.

  Microsoft sells more than 7; Try Amazon.com.

  Go to your computer / computer laptop manufacturer Web site and see if Windows 7 drivers are available for your make and model computer / laptop.

  If this is not available, Windows 7 will not properly work for you.

  Run the "Windows 7 Upgrade Advisor.

  http://www.Microsoft.com/en-US/Download/details.aspx?ID=20

  Check if your specifications are compatible for Windows 7:

  "Windows 7 system requirements"

  http://Windows.Microsoft.com/en-us/Windows7/products/system-requirements

  "Windows 7 Compatibility Center" for software and hardware:

  http://www.Microsoft.com/Windows/compatibility/Windows-7/en-us/default.aspx

  Windows 7 upgrade paths:

  http://TechNet.Microsoft.com/en-us/library/dd772579 (v = ws.10) .aspx

  «Installation and reinstallation of Windows 7»

  http://Windows.Microsoft.com/en-us/Windows7/installing-and-reinstalling-Windows-7

  @@@@@@@@@@@@@@@@@@@@@@@@

  Follow these steps before buy you and upgrade (new installation) of Windows 8.1.

  Microsoft sells more than 8/8.1.

  Try Amazon.com, etc.

  Check if the manufacturer of your computer/laptop has Windows 8.1 drivers available for your model.

  If this is not available, Windows 8.1 not install and work properly for you.

  There is a lot of information in this first link from Microsoft:

  Download and run the Windows Upgrade Assistant 8.1 of to see if your machine is compatible Windows 8.1 and read the update for Windows 8.1: FAQ here

  "Update to Windows 8.1: FAQ".

  http://Windows.Microsoft.com/en-us/Windows-8/upgrade-to-Windows-8

  "8.1 for Windows system requirements.

  http://Windows.Microsoft.com/en-us/Windows-8/system-requirements

  @@@@@@@@@@@@@@@@@@@@@@@

  How to buy Windows 10:

  http://www.microsoftstore.com/store/msusa/en_US/cat/Windows/CategoryID.70036700

  But first make sure that you have the correct configuration and your computer manufacturer provides the right drivers for 10.

  https://www.Microsoft.com/en-us/Windows/Windows-10-specifications#sysreqs

  " System requirements Windows 10"

  https://www.Thurrott.com/Windows/Windows-10/3884/Windows-10-system-requirements

  Microsoft deploys Windows 10 available as free upgrade to Windows 7 features, Windows and Windows Phone 8.1 8.1 qualified. It will be available from July 29, 2015

  "FAQ Windows 10.

  http://www.Microsoft.com/en-us/Windows/Windows-10-FAQ

  See you soon.

• Windows vista 683 gb hard drive full of only the dates, how can I clean it? Fixed thanks

  Windows vista 683 gb hard drive full of only the dates, how can I clean it? I have 9 GB of free space. PC still allows me to watch Netflixs. Cool

  You are welcome.

  See you soon.

• Windows Vista Home Premium SP2 32-bit not updated, the error code 80070005.

  Windows Vista Home Premium SP2 32-bit not updated, the error code 80070005.  Have tried little about everything without success. AV is Microsoft Security Essentials, Norton has preloaded, ran Norton total clean. Don't know the last updated time to race day, I re-load of updates (right term?) who cleaned the logs.  Have the free version of Malwarebytes, run regularly, nothing comes.

  Fixed, had run as before, but didn't save Subinacl desktop instead of folder mentioned in fix

• I have 2 versions of windows vista running on my computer. One is before it crashed and it took all the RAM (Ram)

  I can't clean the discs because I can't load any programs because the memory has faded.  So I can not put a page of my computer desktop or download programs, I need to get my images that I have on the other program running.  I can't open one of these programs because I don't have the authorization even if I was always the user and administrator.  What I would do.  Can I add more memory Ram?  Can I remove the old stuff that I can't open anyway.  DLLs etc.  I downloaded vista 2pr, but it does not work.

  Hello

  Here is the information from your other question here about it:

  "I can't collect any information of my system information page."  When I connect I get redirected to a page that asks me what version of vista I want to open.  One is Microsoft vista and the other is windows vista.  The Microsoft is the only one that works. The other takes me a blank page. »

  "I have 2 versions of windows vista running on my computer. One is before it crashed and it took all the RAM (Ram).

  I suggest that you save your data and reinstall the operating system properly.

  There are several methods to reinstall Vista.

  See what methos works for you.

  There is no Windows Vista downloads available from Microsoft.

  You can contact your computer manufacturer and ask them to send you a set of recovery disks.

  They should do this for a small fee.

  To reinstall Vista using their recovery disk/s, you start from the 1st recovery disk they provide and follow the manufacturer's instructions to reinstall:

  You need to change the Boot order to make the DVD/CD drive 1st in the boot order:

  How to change the Boot order in BIOS:

  http://pcsupport.about.com/od/fixtheproblem/SS/bootorderchange.htm

  "How to replace Microsoft software or hardware, order service packs and replace product manuals.

  http://support.Microsoft.com/kb/326246

  And if you have never received a recovery disk when you bought your computer, there should be a recovery Partition on the hard drive to reinstall Vista on how you purchased your computer.

  The recovery process can be started by pressing a particular combination of the key or keys at startup. (Power on / start)

  Maybe it's F10, F11, Alt + F10, etc., depending on the manufacturer.

  Ask them to the proper key sequence.

  And if you do not score a manufacturer of recovery on your hard drive, you should be able to make your own recovery from her disks to reinstall the operating system.

  Go to programs > name of the manufacturer of your computer > then their system or recovery tools software topics for them, depending on how it is formulated.

  If you can't find any reference to it, contact the manufacturer for advice on how to make these recovery disks.

  Some manufacturers have more available Vista recovery disks.

  If this happens, you may need to try this instead:

  You can also borrow and use a Microsoft Vista DVD, which contains the files for the different editions of Vista (Home Basic, Home Premium, Business and Ultimate) must be installed. The product key on your computer / Laptop box determines what Edition is installed.

  Other manufacturers recovery DVDs are should not be used for this purpose.

  And you need to know the version of 'bit' for Vista, as 32-bit and 64-bit editions come on different DVDs

  Here's how to do a clean install of Vista using a DVD of Vista from Microsoft:

  "How to do a clean install and configure with a full Version of Vista '

  http://www.Vistax64.com/tutorials/117366-clean-install-full-version-Vista.html

  And once the operating system is installed, go to your computer manufacturer's website and get the latest drivers for your particular model or laptop computer.

  And phone Activation may be necessary when you use the above installation method.

  "How to activate Vista normally and by Activation of the phone '

  http://www.Vistax64.com/tutorials/84488-activate-Vista-phone.html

  See you soon.

• Update Windows Vista error code A 8024, 000 after replacing the HARD drive

  Hello

  I had to replace the failed hard drive on my laptop (I replaced it with the same brand and size).

  After that I used the recovery CD, Windows Update gives me error code A 8024, 000.

  I tried the solution provided in this thread, but did not work for me:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_other-windows_update/Windows-Update-error-code-8024a000/562845f3-78d5-42A0-bed5-e3fd39f01df7?page=1&TM=1337378075490

  I also tried to load the Microsoft Fixit utility, which has not installed, I tried to update the installer but it gave me an error as well. Also the installation of SP2 crashed with an error (8000ffff if I remember correctly)

  Any help is appreciated.

  Thank you.

  Eugen

  Hello

  1. which utility Microsoft Fixit did you tried to load?
  2. what happened when you tried to load the Microsoft Fixit utility?
  3. what was the error message when you try to update the installer?
  
   
  Method 1: Try running the fix - it of the article mentioned below, if you not him have not yet tried.
  The problem with Microsoft Windows Update is not working:
  http://support.Microsoft.com/mats/windows_update/
  Method 2: run SFC scan. Analysis (sfc) System File Checker will Windows replace corrupted or missing system files on your computer.

  Scan sfc enforcement procedure:
  a. Click Start, click principally made programs, accessories, right-click on command prompt and select run as administrator.
  b. click on continue or provide administrator credentials if prompted.
  c. in the type in the following command prompt window and press ENTER:

  sfc/scannow
  Refer to this article for more information:
  http://support.Microsoft.com/kb/929833
   
  Method 3:
  
  0x80000FFFF error code when you download updates on a computer running Windows Vista by using Windows Update or Microsoft Update:
  http://support.Microsoft.com/kb/946414
  Important: this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
  http://support.Microsoft.com/kb/322756/
  Download Windows Vista Service pack from here:
  How to obtain the latest Windows Vista service pack
  http://support.Microsoft.com/kb/935791
  Reference:
  The problems with the installation of the updates:
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-with-installing-updates

• I am trying to upgrade Windows Vista Home Premium. When I click on the UPGRADE button then it will display a window in Turkish. I need the window in English.

  Upgrade in an incorrect language window

  I am trying to upgrade Windows Vista Home Premium. When I click on the UPGRADE button then it will display a window in Turkish.  I need the window in English.  Can you please help?

  Thank you!!

  Hello

   
   
  1. You bought a Turkish version of upgrade CD?
  2. How you are trying to upgrade? (To CD using, every time that the update)
  3. What version you are trying to upgrade? Is - this Windows 7?

  Make sure you have the operating system to install a correct language.

  You can visit these links and check:

  http://Windows.Microsoft.com/en-us/Windows-Vista/products/anytime-upgrade

  http://Windows.Microsoft.com/en-us/Windows-Vista/how-do-I-get-additional-language-files

  Response so that we can better help you.

• Windows Vista Home Premium Service Pack 2 upgrade of the Atheros AR5007EG wireless network adapter

  I just bought a new device Sierra Wireless mobile hotspot, the Pro of the Sprint Overdrive.  The wifi connection works very well in my PC with the exception of a PC set that I am running Windows Vista Home Premium Service Pack two.  I am told that the problem is with Vista and the Atheros AR5007EG wireless network adapter.  The current version is 7.6.0.164 and it tells me the device Overdrive only with version 9.1.0.328 or higher will.  What I can, and if I can, how to move the driver to the required version?

  Hello

  You can try to update the latest drivers for the network adapter and check if it helps:

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  It will be useful.

• The desktop ICONS: I use window Vista Basic in my laptop icon changes little icon real player and it is not editable by the option in their original form.

  I use window Vista Basic in my laptop icon changes little icon real player and it is not editable by the option in their original form.

  What can I do there is no virus I have AVG anti virus

  Try to rebuild the icon cache using the following: http://www.vistax64.com/tutorials/117229-icon-cache-rebuild.html.

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Windows 7 on my laptop, when I plug my apple Ipod classic to a USB port, I get a message that says: I need an Apple mobile device USB driver

  I have windows 7 on my laptop, when I plug my apple Ipod classic to a USB port, I get a message that says: I need an Apple mobile device USB driver. When windows search the driver it says failure of driver to install, I need something mobile apple USB driver. Can someone tell me where to find this driver. I installed Myapple and Itunes.

  Hello

  I recommend that ask you this question on the following support forums.

  iPod: Apple support communities: https://discussions.apple.com/community/ipod

  The experts, it should be able to help.

  Concerning

• Notebook15-r110na Energy Saver: my laptop screen has suddenly started to go black when I need to plug the power adapter

  Laptop screen has just started to go black when I need to plug the power adapter to recharge, if I get screen back to normal.  I have not downloaded anything new recently.  I have download the free 10 Windows but that was months ago.  Any help would be appreciated, but please not too technical as I'm not an expert on computers.

  Maybe the powerplan battery is changed or not properly configured. You can see the current powerplan thanks the battery status bar icon.
  Please check if the powerplan options are correct.
  More specific:
  Brightness updates when it is plugged into the charger OK?
  
  Also: If the screen goes black, can still use you the shortcut keyboard keys to adjust the brightness?