wireless users

Similar Questions

• How have use ACS supported wireless users and the VPN user?

  I'm new to ACS and configure the following requirement:

  (1) ACS to authenticate users wireless with window AD.

  (2) once connected successfully to the radio, the user must use VPN for remote access with the ASA.

  (3) the end-user will have only 1 common username but different password.

  for example:

  username: password: cisco: cisco wireless.

  username: cisco password: 1234 for VPN.

  ACS support can this, if yes how can we do? Do I need 2 sets of ACS?

  Yes, acs should work properly according to your need.

  ACS, we have a feature called NAP "network access profile" where we can define the condition based on ip source or attributes which allow to say if the request comes from wireless device acs will forward to AD and if the request is of the acs VPN will forward to this diff of database.

  Basically, we need to use two acs database.

  http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_server_for_windows/4.1/user/NAPs.html

  Kind regards

  ~ JG

  Note the useful messages

• Test command of the AAA for EAP - TLS authentication for wireless users

  Hi all

  Can anyone suggest me the test command to verify the eap - tls authentication for the Cisco WAP's wireless.

  If it's an authetication jump we can use the command to test the connection below

  Radius of group aaa Testwap-01 #test [email protected] / * / o4 & yJ) NoL$ new-code %0
  Trying to authenticate with the server radius group
  User successfully authenticated

  But eap - tls is not delivered with the password. He insists that for the user name.

  We strive for remote location then test remotely before production.

  If someone help pls in that if we have a command to test or debug command to test this authentication.

  EAP - TLS requires a client certificate. How can you have a simple command that analysis without loading any certificate on the router/switch? It does not exist. This is why eap - tls is not considered an easy to deploy eap method: because it can go wrong on several levels.

  The aaa command test performs a PAP authentication, therefore, it tests the connectivity of the base RADIUS and name of user and password.

  If it works, the only thing that can break for eap - tls are certificates, as well as the radius server will be able to tell if something worng.

• Wireless user is unable to connect to Server 2008 r2

  I just migrated to Server 2003 r2 to Server 2008 r2 in my company. I have a pretty good work for all users of wired & wireless on Server 2003 r2, but once I upgraded to the counter and Server 2008 r2 user wireless can not connect to the server but Wired user works very well.

  I realize that if the user wireless connect the wireless name is showing field name... Yes, I can connect to the server. But, if the wireless name showing SSID then failed to connect to the same server not ping IP of the server also no response. I tried manually inside the server IP in favorite DNS server also failed.

  Help, please!

  Hello

  I suggest you to ask your question in the following TechNet Forum for better support.

  Windows Server 2008 R2 network.

  http://social.technet.Microsoft.com/forums/en-us/windowsserver2008r2networking/threads

  I hope this helps.

• How many concurrent wireless users the WRT54GR can support

  recently I started having problems with my WRT54GR.  my sons phone keeps disconneting and it will service own phone to get data from the internet. I was wondering if it has a limit to how many users simultaneous wifi?

  32 if I remember correctly.

• LAN network is working, wireless users isn't getting an IP address

  HY,

  I buy a CISCO 861W two days ago and I am trying to build my own wireless network at home but unfortunetly I do not get any IP address from the DHCP server via the wireless network. LAN my computers get IP addresses and I have an internet connection. The problem is when I go to wireless technology and I don't know what's wrong. I admit that I was not worked up to now with cisco wireless devices, I know how to build networks in the world connected Cisco. I have attached two configurations. Please, someone tell me where is the error. Thanks in advance.

  PS: I changed the dns and address wan with a few addresses randomly.

  Service contract number is the number of contract... If you know the serial number of the FRAME then you can call toll-free Cisco TAC toll free number and then to raise the case with us... Here is the link...

  http://www.Cisco.com/en/us/support/tsd_cisco_worldwide_contacts.html

  Concerning
  Surendra

• Windows 7 slow login / delay authentication question user wireless via ACS 5.8

  Just set up a new ACS 5.8 farm (only 2 servers) here and which I hope someone here can shed light on the difficulties.

  The new ACS server is set up to correctly authenticate administration network device and I am currently working on the definition of profiles for our wireless users authentication and business laptops.

  Being new to this version of ACS (we will migrate manually ACS 4) I followed an excellent example of this task described in a video on this site: http://www.labminutes.com/sec0044_ise_1_1_wireless_dot1x_machine_auth_peap

  I managed to have a Windows XP sp3 client authenticate properly, first with the authentication of the computer, then the authentication of users... and the domain logon process takes place in a short period of time< 1min="" and="" the="" user="" gets="" all="" their="" networked="" drives="" via="" the="" domain="" login="">

  However, I'm fighting to get our Windows 7 clients to authenticate properly.  It seems that the machine authentication does not work as expected (I can ping the laptop test from another machine on the network while the test machine is sitting at the login screen; and I see Authentication host recorded in the papers of authentication Radius ACS).  But, when a domain user logs in with his credentials, the connection process takes 4-5 minutes before an event to authenticate the user is entered in the register authentication Radius ACS, after which the login process completes, except that the domain logon script does not work and the user does not receive the drive mappings.

  Can someone point me in the right direction here?  I would be grateful any entry on this.

  Thanks in advance,

  John

  I had a similar problem with Wireless 802.1 x Win 7 clients unable to connect unless they had cached credentials of the AD.  Authenticate in the machine, but the user would take a lot of time if the Windows credentials have been cached.

  I could solve the problem by expanding the ACL of the air space used during the user authentication to include all DC in the environment.

• Users in Virtual Mode of Inband L2 wireless

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-marge-top : 0 ; mso-para-marge-droit : 0 ; mso-para-marge-bas : 10.0pt ; mso-para-marge-left : 0 ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}

  Hello

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-marge-top : 0 ; mso-para-marge-droit : 0 ; mso-para-marge-bas : 10.0pt ; mso-para-marge-left : 0 ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-marge-top : 0 ; mso-para-marge-droit : 0 ; mso-para-marge-bas : 10.0pt ; mso-para-marge-left : 0 ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}

  At present the access point are just plugged access ports in vlan 10 and configured with vlan 10 SSID on the access point for wireless users users access the network very well without any problems. I have setup a CNA in L2 inband virtual mode it works fine when I tested for WIRED users.

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-marge-top : 0 ; mso-para-marge-droit : 0 ; mso-para-marge-bas : 10.0pt ; mso-para-marge-left : 0 ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;} To apply the evaluation of posture on wireless users, I just change the access switch ports vlan for authentication VLAN where the access point is connected to present and change the SSID vlan 10 to authentication vlan. As I m using only 1 vlan so I don't have to create a trunk switch port where the access point is connected? Anything else I should do? Correct me if I m wrong

  Answers?

  Hi Michael,

  These conclusions should be correct.

  Just to be 100% sure, we are in phase on your first conclusion.
  The switchport where the access point is connected must be configured as an access port on vlan 20, in the case where the AP and wireless clients are connected on vlan 20.
  However, be very careful that in such a situation, your AP traffic can also affect the CASE (being on the same vlan unreliable with regard to regular customers).

  Then you can consider keeping your AP on a BVI interface vlan separate in what concerns the vlan of the customer, otherwise you can end up breaking the AP traffic, because it is placed on the same vlan not reliable as your wireless clients. An alternative could be to add a filter for the AP in cam, but it is perhaps not as scalable that separate the traffic of the client subnet IVB of the AP wireless.

  Kind regards

  Fede

  --
  If this helps you or answers to your question if it you please mark it as 'responded' or write it down, if other users can easily find it.

• My PC is connected to the wireless network, but it is impossible to open any internet page. I went through the diagnosis of Internet Explorer, see below.

  Diagnosis of last run time: 28/01/12 10:16:32 Gateway diagnosis

  Entry door

  Info the following proxy configuration is used by IE: automatically detect settings: enabled Automatic Configuration Script: Proxy Server: Proxy bypass list:

  info could not get the proxy settings via the Proxy Automatic Configuration mechanism

  Info this computer has the following (s) default gateway: 0.0.0.0

  warn that there is no default gateway entry

  repair automatic action: reset the network connection

  action to disable the network card

  activation of the card network action

  successfully activated information network adapter

  Info this computer has the following (s) default gateway: 0.0.0.0

  warn that there is no default gateway entry

  user redirection of information in support of the appeal

  IP layer diagnostic

  Corrupted IP routing table

  prevent the default route is missing or not valid

  Invalid entries in the ARP cache

  action cache ARP has been emptied

  Diagnosis of IP Configuration

  Invalid IP address

  detected info valid IP address: 192.168.0.1

  Wireless diagnosis

  Wireless - Service disabled

  Wireless - user SSID

  required user input action: specify the name of the network or the SSID

  Wireless - first installation

  Info the name of the wireless network (SSID) to which the user wants to connect is IrinaLaptop-router.

  Wireless - Radio

  detected info valid IP address: 192.168.0.1

  Wireless - off limits

  Wireless - hardware problem

  Wireless - Novice user

  Wireless - network Ad - hoc

  Wireless - less preferred

  Wireless - 802. 1 active x

  Wireless - Configuration mismatch

  Wireless - low SNR

  WinSock diagnostic

  WinSock status

  info all base service provider entries are present in the Winsock Catalog.

  channels of information the Winsock Service provider are valid.

  Info entry provider MSAFD Tcpip [TCP/IP] passed the loopback communication test.

  Info entry provider MSAFD Tcpip [UDP/IP] passed the loopback communication test.

  Info entry RSVP UDP Service Provider provider passed the loopback communication test.

  Info entry RSVP TCP Service Provider provider passed the loopback communication test.

  Info connectivity is valid for all Winsock service providers.

  Diagnosis of network adapter

  Network location detection

  Info to help home Internet connection

  Identification of network adapter

  Info network connection: name = connection to the LAN, device = Broadcom 440 x 10/100 Integrated Controller, MediaType = LAN, type = LAN

  Info network connection: name = wireless network connection, Device = Intel (R) PRO/Wireless 3945ABG Network Connection, MediaType = LAN, type = Wireless

  Info network connection: name = 1394 connection, device = 1394 Net Adapter, MediaType = LAN, type = 1394

  Info network connection: name = connection high speed, device = Miniport WAN (PPPOE), MediaType = PPPOE, type = NONE

  Info network connection: name = blank, peripheral = Miniport WAN (PPPOE), MediaType = PPPOE, type = NONE

  Info both Ethernet connections and wireless available, ask the user for selection

  required user input action: select network connection

  Info Wireless connection selected

  State of the network adapter

  Info network connection status: connected

  HTTP, HTTPS, FTP Diagnostic

  HTTP, HTTPS, FTP connectivity

  warn HTTP: error 12007 connecting to www.microsoft.com: the server name or address cannot be resolved

  warn HTTP: error 12007 connecting to www.hotmail.com: the server name or address cannot be resolved

  WARN HTTPS: error 12007 connecting to www.microsoft.com: the server name or address cannot be resolved

  WARN HTTPS: error 12007 connecting to www.passport.net: the server name or address cannot be resolved

  WARN FTP (passive): error 12007 connecting to FTP.Microsoft.com: the server name or address cannot be resolved

  WARN FTP (active): error 12007 connecting to FTP.Microsoft.com: the server name or address cannot be resolved

  error could not make an HTTP connection.

  error could not make an HTTPS connection.

  error could not make an FTP connection.

  I did not want to do this (restore point). However, I found a solution. It comes: http://forums.techguy.org/networking/1029348-network-connection-status-media-disconnected.html

  Where there are two crucial steps (do not know if the two were needed) RUN command (1) netsh int ip reset reset.log and (2) netsh winsock reset catalog
  
  
  After a restart, hey presto my wireless connection was repaired. This seems useful, but not essential (shows wireless performance but not the solution): http://wpc.475a.edgecastcdn.net/0047...etup.1.2.0.exe which is run Xirrus Wi-Fi Inspector 
  Thanks for your time!
  Good bye

• New HD and in HD windows XP now I can not find my USER auto

  I installed a new HD and format of operating system XP and everything works, but today, I bought a new iphone and tried to find my network and I can't find it on the iphone or another phone!

  All laptop computers work but I can't find my wireless user name when searching to add an iphone wireless to this topic

  That's happened?  I tried another phone and it does not find this router

  I foregot my user name and password to get in beat him! I think I had that on the hard drive I removed

  Default user name sorry is empty, password "admin".

• Wireless router E4200 and share a printer on the subnet

  Hi all

  Now I've been tinkering for 4 days trying to resolve a problem with this, but I couldn't understand it, so I'm hoping to find someone who can help.

  My question is sharing a printer on my main network and the wireless,.

  the description of the parameter:

  I have my main network 10.1.1.0/24 (RV082)

  I plugged the E4200 router in an IP 10.1.1.82 and the wireless network is 192.168.1.0/24

  Set up a printer/scanner with an IP 192.168.1.72 to share on both networks.

  Now everyone on the 192.168.1.0 network is able to access and print but none on 10.1.1.0

  I put a static route on the RV082 to direct applications of the printer be redirect to 10.1.1.82 but without success.

  The E4200 is configured by default out of the box, I had to just put the static IP address, gateway and DNS and, of course, the key to wireless security, nothing else.

  the NAT is enabled on the E4200 and RIP is disabled, I tested the connection by disabling NAT and allowing the RIP, during which I was able to connect to the printer, but Internet went down for wireless users all (192.168.1.0 network)

  So I need help to solve this problem please.

  1. I would recommend to connect the printer to the main network. He two subnets can access the printer regardless of the configuration on the E4200.

  2. If you want to only an extension of your existing network wireless, I would recommend using the bridge mode on the E4200. In this way, wired and wireless networks are in the same IP subnet and everything is much easier.

  3. with NAT on (default), the LAN is inaccessible from the side WAN. This is why your RV protects your local network from the internet. And that is why the printer is not accessible from the RV subnet unless you configure the port forwarding on the E4200.

  4. it is thus with active NAT, you must send the necessary ports for printing on the E4200 and you must configure computers on 10.1.1.0/24 to use 10.1.1.82 to print the wireless network uses 192.168.1.72.

  4. with disabled NAT, you must configure a static route on the RV to route 192.168.1.0/24 to 10.1.1.82.

  5. with disabled NAT wireless clients have no internet because the RV does not NAT the 192.168.1.0/24 subnet. The RV is that NAT because it is own LAN IP subnet 10.1.1.0/24 but not for 192.168.1.0/24. This means that the RV will forward packets 192.168.1. * unmodified in the internet where they are rejected. You must configure the RV to NAT for example 192.168.1.0/24. You must apply to the Cisco Small Business community, whether or not this is supported on the RV.

  So in summary, I recommend to use Bridge on the E4200 mode and function as a single IP subnet. That would solve all your problems.

• SonicWALL TZ300W and wireless

  TZ300W wireless can be configured without guessing wireless, just a simple sentence of WPA2?

  I want to check if they have no internet or not DNS.

  Try ping 8.8.8.8. If you can then you have internet access, but cannot resolve DNS.

  Are you distributing internal DNS to wireless users? If so, I would suggest distributing public DNS. Unless you have a need for users wireless invited resolve internal DNS names.

  Kevin

• Do not allow users to auth for FW/RTR CSACS

  We use our CSACS server to authenticate wireless users. I find thoguh I can't add users to the user group's wireless and allow them to authenticate via access points without them also have access to our infrastructure network (routers, switches, firewalls).

  How to stop a group/user to authenticate devices? I just want to authenticate if the request comes from the APs.

  Thank you

  Use the access network (OAN) section under the Group of ACS, particularly the section "by group NAR. You put all your users wireless in a specific group to the ACS, and then you add in your wireless AP in as 'Authorized the calling Points' under "IP set access restrictions", which means that users are allowed to authenticate to them, but not anything else. Put a * in the values of Port and an address, you care to those, only the fact that the authentication request is from the AP.

  If you go into the Configuration Interface - options advanced and enabled groups of network (NDG) devices, you can also put NDG under one of your AP and then just set this NDG in as a Point of Appeal allowed

• RV220W wireless access management

  Is it possible to disable management of the wireless router? My point is that anyone (being a user wireless or someone else) could hack the password of the exterior of the building and change the settings of the router via a wireless connection. I know that the lower range of Linksys offers this feature, but I can't find it for the RV220W. I actually want to make sure that only one Ethernet device allows to manage the router. That will add to the security that I currently have full control over these computers.

  Daniel,

  The RV220W doesn't have a function to block the web administration for wireless users along with some of our existing products. Please do not forget to use a strong password.

  Edit: You can add a second VIRTUAL LAN to wireless users and disable device under Table membership management VLAN.

  -Marty

• Pull wireless

  Hi gays! I want my application to install on wireless (user-initiated) sweater
  I want to post applications compiled on a public web site. Device users can visit the website to download applications on the wireless network using the browser on their BlackBerry devices (guests browser users to install the application, then the application downloads via the wireless network and is installed on the BlackBerry smartphone)

  But how can I install only for specified devices? For example: my request for 4.2 devices and user have 4.1 device. If the user installs my request, it will not work... ((How is it possible to avoid this situation?

  The ALX file only works to distribute an application from a computer...

  Help, please!

  Thanks in advance!

  When you receive the blackberry browser application, you can check the user agent and let your web server to act based on the information received.

  Click here for more information.

  http://www.BlackBerry.com/knowledgecenterpublic/livelink.exe/fetch/2000/348583/800878/800733/How_To _...