With regard to the Epson V300 scanner. I installed the current version software driver successfully. It works fine until I turned off the computer. After the reboot, the scanner is not recognized and driver not found.

Similar Questions

• Pavilion dv6-6135dx: spread juice on laptop and worked fine until I turned off and tried to turn it back on.

  Not a lot of common juice but apparently enough hurt my laptop. He flipped on the upper right of the keyboard and I immediately wiped them all and the laptop seemed fine. I turned it off and when I went to use it, it not light. He also made a noise of sizzle on the top of the right side. Help!

  The sizzle is probably the sound of your motherboard short-circuit (die). The juice is probably infiltrated gradually down inside and when you applied the still-zap power.

  For what it's worth now no matter what time pours on a laptop, it must immediately be put out voltage, battery & power cord removed and the laptop placed upside down for at least 24 hours to evacuate just a little liquid.

• Error "LoadLibrary failed with error 126: the module is not found ' at the launch of programs

  Original title:

  From some programs, the program starts partially, then a pop up message saying "LoadLibrary failed with error 126: the module is not found. When you click on the 'OK' button, the program stops. I had this problem with several graphics applications such as PSP and Rhinoceros 3D.

  Any suggestions what can be causing this "error 126"?

  type cmd and click the black box for it...

• My computer says updated configuration failure, recovery changes, do not turn off your computer... I left on three days and he said that

  My computer says updated configuration failure, recovery changes, do not turn off your computer... I left over three days, and he said that. Does anyone know how to get that back in Windows so I can use my computer. It is a laptop Windows 8.

  Do a Startup Repair:

  Auto repair - run in Windows 8 - Windows 8 Forums

  Let us know if it is not resolved

• Hi, I have the latest version of lightroom. It works fine until last night when I tried to import some files in lightroom. It will come out with a message "could not copy a file at the location requested. (113)

  Hi could someone help me with this problem.

  I tried to import pictures to destination Macintosh HD or my external hard drive but it continue to go out with the same message "could not copy a file at the location requested. (114) items 1-100: articles 101-114.

  Interestingly, it was working fine up until yesterday.

  I tried restarting computer, I have the latest version of lightroom, I use Mac Os x Yosemite 10.10.4

  Thank you very much

  Hi josepht,.

  Looks like your destination folder does not have a full read and write permissions.

  Try to set the destination as a specific folder that contains all the permissions on your local or external drive, then, check.

  Kind regards

  Claes

• Error "LoadLibrary failed with error 126: the module is not found" when run Minecraft

  I tried to load my Minecraft, Minecraft is everything to date and nothing wrong with it. I deleted and re-installed, and I still get this problem.

  Pitcher of the same technical does not work so he couldn't be just minecraft (Technic Modded = customer type of)
  I even made another account on my laptop and some files to another account just Minecraft and it still does not work, in browser game works perfectly, but on computer laptop, it is not, it allows to work but now is not.
  I did all of the things listed on that, and Minecraft still does not work.
  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-windows_programs/error-LoadLibrary-failed-with-error-126-the-module/c5b67473-00f8-4E4A-b8a5-f7f9c619c3d9
  I am running Windows 8, Dell Inspiration M5040.
  
  I hope that you could solve my problem.

  Had this problem on my pro Win8

  Uninstalled 64-bit Java (7 update 17) and left the 32 bit one.

  Has started working without any other trix.

• "Error while interacting with the scanner: the selected scanner was not found." Called brother and my MFC 7360N works very well with other programs to scan - only problem with Adobe Acrobat Pro 11.

  "Error while interacting with the scanner: the selected scanner was not found." Called brother and my MFC 7360N works very well with other programs to scan - only problem with Adobe Acrobat Pro 11.

  Hi davidd67669685,

  Please provide the exact point of the software & OS installed on your system. Also check if it is there any update available for the software after going through "help > check updates.

  Follow this thread to reset the Acrobat preferences:- How to reset preference settings in format Acrobat.

  You can check after connecting this scanner locally to the system if asked its connected on network & then look for the same thing.

  Please refer to this article:- of the troubleshooting tips for scanning questions when using Acrobat

  If the problem persists ask please check with another user account.

  Kind regards

  Christian

• I get the message that running ' Ckdsk/f' the file is not found. I can't defragment drive c.

  I can't dfragment c drive. I get the message run Ckdsk/f. The file is not found.

  the command is CHKDSK /F.

  However, it is best to run this instead: CHKDSK /R

  It is unclear if you do not run the check disk drive correctly or if the check disk command / file is affected by the volatile file system.

  my suggestion is to acquire a xp boot cd and boot the recovery console.

  then when you get to the disk prompt run the command >: CHKDSK /R

  then type exit, remove the cd and boot into windows.

• I come from components to build a new computer. Try to use the Windows XP Pro computer old version but after BIOS and XP installation I get the error "file not found \i386\ntkrnlmp.exe. The error code is 7. "What should I do?

  New components is a new computer.
  Inserted the XP Pro CD in the drive but get the error "file not found \i386\ntkrnlmp.exe. The error code is 7. »
  Rebooted comp 5 times with the same problem after BIOS.

  Hi Milkshake83,

  Thanks for posting. Proceed as follows for this error.

  Method 1: Restore the default settings of the BIOS WARNING: this procedure may involve changing the semiconductor (CMOS) settings of the computer's complementary metal oxide and by changing the BIOS of the computer. Incorrect changes to the BIOS of your computer can result in serious problems. Change the CMOS settings of the computer at your own risk.

  To resolve this issue, restore the BIOS of the computer to its default settings. For more information about the correct settings of the BIOS of the computer and how to check and change these settings, see the computer documentation or contact the manufacturer of the computer.

  In addition, to confirm that the computer's BIOS is current, contact the computer manufacturer to inquire about the last update of the BIOS available for the computer.

  Back to top

  Method 2: Remove the faulty RAM to resolve this issue, remove the memory modules installed in the computer.

  NOTE: you must leave enough RAM for the computer to start and run Windows.

  For more information on the amount of RAM that is required to run Windows, click on the number below to view the article in the Microsoft Knowledge Base:

  304297 configuration (http://support.microsoft.com/kb/304297/) System requirements for Microsoft Windows 2000 operating systems

  If the error message described in the "Symptoms" section of this article appears again after removing the memory module, remove a different memory module. This procedure may ask you to restart your computer several times to identify the specific memory module that is not working properly.

  For more information about how to add and remove RAM to the computer, contact the manufacturer of your computer or see the documentation that came with your computer.

  http://support.Microsoft.com/kb/318729

  I hope this helps!
  Shawn - Support Engineer - MCP, MCDST
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• My computer is stuck in "configuration updates: stage 3 of 3 0% complete.". Do not turn off your computer. It restarts just over and over again with the same message.

  I have a Dell Inspiron 1525 with Windows Vista, and I have tried the following to fix my endless reboot with the "Configuring updates: stage 3 of 3 0% complete.".  Do not turn off your computer. »

  • I inserted the cd 'Réinstallation DVD Windows Vista', but it won't pop up any kind of prompt for me to do something with it.  I tried putting the cd in what was on the computer and tried leaving him in and restart it - but the cd has no EFFECT.
  • I used the F8 key and I tried the following with no luck: safe mode, safe mode with network, safe mode w / command prompt, enable logging, last known good configuration (Advanced) boot and debug mode.  Most of these options make the monitor off (to make you think he will do something), then it just restarts and did the thing reboot loop again and again.
  • I also tried the repair your computer option to the F8 key.  He asks me to log in as an administrator (but my password does not work).  So, I use the menu drop down and choose the name of my computer and then use my password, and I can connect to "restoration of access options '.  Once I'm in the "System Recovery Options".  I tried the following with no luck: Startup Repair tool, restore the system, Windows complete PC Restore, Windows Memory Diagnostic tool and command prompt.  THE only ONE that I HAVE NOT YET TRIED it IS THE "DELL FACTORY IMAGE RESTORE", it's because I want to try to fix it without losing everything on my hard drive.  Here are the details of the I've tried in the "System Recovery Options".
  • The command prompt says: 32 X:\Windows\system > (I have no idea how to use it, but it's what he says)
  • The memory diagnostic tool reboots the computer, but nothing new happening (just reboot over and over again)
  • In the PC restore full Windows: I tried to put the Windows Vista CD in, but it can not find a valid backup location
  • When I click on the system restore: it is said: "no restore points were created on your computer's system disk.  To create a restore open system protection point.  When I click on the system protection, it is said: "your computer is running in a limited diagnostic State.  If you use the system restore in this limited State, you can't undo the restore operation.  Help topics are not available in this State. "  So I press OK, and I'm back to square one.
  • When I click on startup repair: it says "Startup Repair could not detect a problem.
  • I know there are many many posts on this problem, and I think I've tried all the suggestions on how to solve the problem, but they do not work for me.
  • PLEASE HELP ME!  I need my computer for my college work.  I can't borrow laptop my friend forever!

  Hello

  I guess that part of the question could be a driver which is really old or similar should not be loaded.

  This exit Windows updates on (after you have access) and stop the updates of the driver to load.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  ---------------------------------------------------

  You can use the solutions in this KB - 3 methods and I listed a little help for them below

  The update is not installed successfully, you receive a message, and the computer restarts when you try to
  install an update in Windows Vista
  http://support.Microsoft.com/kb/949358

  Method 1: Start Windows Vista with the Windows installation media and use the repair feature

  How to do a startup repair in Vista
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  You can also do a safe mode startup repair to access the Recovery Options If you have them available
  or use the DVD as described above.

  This tells you how to access the System Recovery Options
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  Try recovery options Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  Method 2: Start the system in safe mode and then use the system restore feature

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  You can also do a restore of the system of starting with a Vista disk.

  Method 3: Rename the Pending.xml file, and then change the registry (this method is part of the advanced troubleshooting)

  See article below for that.

  You can use this method on the updates that have this problem.
  http://support.Microsoft.com/kb/949358

  Hide the update (click right - HIDE in the updates of Windows) and go to the Microsoft Download Center to download
  and install it.

  Microsoft Download Center
  http://www.Microsoft.com/downloads/en/default.aspx

  ------------------------------------------------------

  Once you are in Windows I was running once again reset here as a precaution.

  How to reset the Windows Update components?
  http://support.Microsoft.com/kb/971058

  Hope this helps sort it out for you.
  Rob - bicycle - Mark Twain said it is good.

• Update fails with the message "configuration updates stage 3 of 3 0% complete. Do not turn off your computer "

  Before closing my lap top, I did 8 automatic windows updates. The next day I had turned on the lap top and other 3 automatic updates had started to download, but when configuring the update a prompt indicates "configuration updates stage 3 of 3 0% complete. Do not turn off your computer ". A few moments later, the laptop restarts and then returns to "configuration updates stage 3 of 3 0% complete. Do not turn off your computer "and restarts again, this continues each time. I'm unable to advance in the journal on stage. Can you help me?

  Best regards Mrs Neil Dowdeswell

  Hi Neil,

  Method 1: Please try last known good configuration boot

  (a) restart the computer.

  (b) press and hold F8 while the computer starts up, which helps you to go to the Advanced Boot Options screen.

  (c) use the arrow keys to highlight and select the last well known configurations and press ENTER.

  This mode will take the last point restart managed computer that helps your computer to boot to the desktop.

  Method 2:  Please see below the article mentioned which may help you in the matter of fixing.

  http://support.Microsoft.com/kb/949358

   

   

  Hope this information helps.

• I'm trying to scan a doc and the message is 'not found computer. Ensure that the HPsoftware has been installed on the computer.

  I'm trying to scan a doc and the message is 'not found computer. Ensure that the HPsoftware has been installed on the computer. My computer print very well so I do not know why it does not scan.

  Hello

  Thanks for the information. Two things to try. First of all, try to align your print cartridges using the controls on the printer display panel. As part of this process, the printer will print on a sheet of alignment that you place on the printer and scan in the printer. See if it works successfully. If not, see the following page: http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02451000&cc=us&dlc=en&lc=en&jumpid=reg_r1002_usen_c-001_title_r0011 .

  The second thing to try is the print and Scan Doctor Utility, download here: http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=mp-114642-1&cc=us&dlc=en&lc=en&os=4063&product=5061082&sw_lang=. Its a standalone process and requires no explanation.

  Let me know if one of them fixes the problem.

  Kind regards

  BearPup

• Just upgraded to Windows 7 and my Dell All IN One Printer does not print. It is said that the pilot of the AIO 942 not found

  Just upgraded to Windows 7 and my Dell All IN One Printer does not print.  It is said that the pilot of the AIO 942 not found.

  Anyone where I can download this driver?

  See http://www.microsoft.com/windows/compatibility/Windows-7/en-us/Details.aspx?type=Hardware&p=Dell%20942%20Photo%20All-In-One%20Printer&v=Dell&uid=942STD&pf=0&pi=1&c=Printers%20%26%20Scanners&sc=Multifunction&os=32-bit.

  There are only drivers for Vista at http://www.dell.com/support/drivers/us/en/04/DriverDetails/DriverFileFormats?c=us&s=bsd&cs=04&l=en&DriverId=R151559.

  They are supposed to work if installed in compatibility mode. http://en.community.dell.com/support-forums/peripherals/f/3528/t/19319527.aspx.

• With regard to the application of Nook on the Surface RT. Is there a way to change the way that newspapers appear?

  With regard to the application of Nook on the Surface RT.  Is there a way to change the way that newspapers appear?  Like corners, they give a better way to navigate and get the overview for the different sections.

  Probably not "such what."  Next time you launch the application, make sure that the menu bar to it and see if there is a feedback icon.  You may be able to comment on what features you want and they can do just that.

• With regard to the previous discussion on the recent settings of the workspace page

  With regard to the post Re: recent files page , when I went back to answer, there is no way to reply to the post.  After trying the settings using the provided screenshots, page of recent files always came every time.  So the answers you have provided are not correct for my particular case.  Finally, I tried without any control in the preferences and that my custom workspace save as I wanted.  Here is how I had to define it.

  Thank you.

  

  It is doubly strange.  I just check and that the other thread is not locked and can be answered.  Someone else has a problem, you reply to this thread.

  Secondly, I turn off the settings described works for me and Photoshop opens without MRU and start work space.

  You did _uncheck_ these settings?  I like the new workspaces, so mine are checked, but it clearly says _Show_ at the beginning of each line.