WLAN reconnect not awake to the top of the standby mode

Similar Questions

• Auto focus does not work in the creative modes

  I use EOS 600 d for the past three years. I was and I am not able to auto focus in creative modes. I actually thought that there is no installation of the auto focus in creative modes. Only when I attended a workshop in Chennai yesterday, I got to know the automatic update facility is available in creative modes too.  I tried with three lenses and in all cases autofocus does not work in the creative modes only. In basic mode, it works well. I browsed the forum and found to RESET. How a reset should be done? Someone please explain. I can't find any updated firmware for 600 d.

  Thank you, Mr.Waddizzle. I did a reset according to your advice and now AF works in the creative modes also. Thank you.

• Satellite L350D - WLAN does not work after the recovery disk

  Hello

  I just got a L350D. I ran the tool recovery disk, without any other program running. It is on a good way to end the second disc and that: BAM! blue screen. Since start-up, my LAN and WLAN does not work.

  He always says ' WLAN 2.0 bg adapter "to which no driver is found. The driver is a Realtek WLAN and LAN.

  Don't you think that the crash of the WLAN and LAN module fails?

  I tried the things:

  System reset
  Reinstalling the driver

  but nothing has worked.

  Someone at - it advice?

  Thank you very much!

  Mycale

  Hello!

  I put t know what is the reason for this BSOD when installing, but you can post the BSOD code? For example, you can search based on Microsoft Knowledge for this code.

  In addition, I would try to update the BIOS of your laptop that you can find on the Toshiba site:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  After you have updated the BIOS to try to update the WLAN and LAN card driver, or try to reinstall Windows using the Toshiba recovery disc.

  Good bye

• Satellite C875-100 - WLan does not work after the victory 8 upgrade - no driver

  I bought a toshiba satellite c875-100 yesterday and I did the upgrade of windows 8.
  Before the upgrade of the network wireless connector worked well, after the upgrade, he doesn't.

  Device Manager showed that my network connector driver was not installed.
  I tried all the drivers of toshiba online for this specific model with the name 'Wireless' in it and later on al the drivers for this particular model, but every time I get the message that the Device Manager cannot find the appropriate driver.

  Adesperate attempt I have just tried to choose a driver from the list of windows itself (I choose the realtek PCI wireless network card) but who gave a sudden stop of the system.

  Anyone have a suggestion how to get my network controller to work?
  If not, is it possible to revert to the version of windows 7, which was already installed?

  Thanks in advance!

  Hi mate

  As I m wrong not the laptop does support RTL8723AE Realtek Wlan card.
  You need the driver that would exactly support the RTL8723AE WLan chip

• Satellite L40-143 - WLAN does not work with the new router

  WLAN on my Satellite L40-143 does not work since I Modem Alice-1121.

  Who can help me, please!

  Hi kenny_21,

  If you have a new WLAN router you must change the configuration that I think

  The new router is visible under WLAN connections and can connect?

  If so try to connect. The standard router password can be found in the manual of it and no doubt, there will be new addresses MAC first before connect you. I put t know the exact configuration.

  Also check the options the WIRELESS card with TCP/IP. Usually, you need automatic IP addresses.

• Why are graphic line not appearing in the Preview Mode when they show in Normal view?

  I use CS4, InDesign I used it for 4 years. I can't understand why this is happening...

  In the tools Panel, I use online tools and circle. Drawing circles on my paper with a weight of 1 race and lines (arrows). The lines are the top item on my page, the last thing I draw. I draw lines that more would go not only to other graphics, but on the text as well.
  

  Problem is that they appear only in Normal mode, not the preview mode. Therefore, I don't think that they will appear on the final document.

  I have often used these tools, and the lines that do not display is a new problem. Can someone shed some light on why this is happening?

  Thank you, Louise

  
  

  I see two possibilities. You put them on a layer that is set to non-printable or you put inadvertently from the default value of the tool for non-printable in the Panel.

• Having error "could not switch to the specified mode hardware".

  When I try to get the windowed mode mode full screen on some of my downloaded games of big fish.com, it gives me the error above. I've been using full front screen with games now it does not work... anyone know if it is the game or something on my computer?

  Hello

  This message can be direct to video card or video driver issue. In general, while playing games computer fails over to a different resolution then what is on your desktop. However, you can try to reduce hardware acceleration, and check if that helps. If this is not the case, try to update or reinstall your video drivers, in case of failure reinstall the game.

  To reduce hardware acceleration, follow these steps:
  1. click on start in the lower left corner of Windows Vista/Windows 7.
  2. click on Control Panel, click appearance and personalization, click personalization, click display settings and then click Advanced settings.
  3. click on the Troubleshooting tab, and then click on change settings.
  Note: The settings will be disabled if the graphics card driver does not support disabling hardware acceleration.
  4. move the hardware acceleration slider until it is one notch to the right of None. It is the basis of acceleration.
  5. click OK twice, and then close the window.
  6 restart the computer if she invites you to.

  Finally, try to alternate with the refresh rate of the screen, to:
  1. right click on the windows desktop and then click Customize.
  2. click on view > click on change display settings > settings click Advanced.
  3. click the monitor tab and change the screen refresh rate > click Ok.

  Let us know if that helps.

  Kind regards
  Clement Kumar.

  Microsoft Answers Support Engineer. Visit our Microsoft answers feedback Forum and let us know what you think.

• the keyboard does not have to return the system to the standby mode

  Windows 7 Home Premium 64-bit system.

  The fundamental problem is that, after working properly for more than a year and a half, this Win7 machine suddenly stopped enlightenment of the mode before using the keyboard a few months ago. It still immediately responds to a mouse click, then dysfunction of the keyboard was only a minor inconvenience. The keyboard is equipped with a PS/2 connector, the mouse uses a USB port.

  However, several times lately the keyboard did not return after the awakening of the system; It is a biggest drawback. Each of these three times the keyboard had returned to normal after a reboot of the operating system, using the mouse to manipulate the Start Menu. I noticed nothing otherwise askew with the keyboard at any time, which suggests that this is not a problem with hardware keyboard. I would like to know how to get the system back to normal.

  I don't know if the following is relevant, but it is similar:
  There is a card audio semi professional, with its own control panel software, installed in the computer. With the exception of the occasional limited testing, I do no audio recording here, but I often work on audio recordings downloaded from other sources. Thus, the audio card is really only reading used mode.

  A few months ago a question arose on the settings of the control panel to monitor a recording against existing tracks. Under Win7, the map control panel is configured differently that in previous versions of Windows, if the answer was not immediately obvious.

  I worked on the necessary configuration changes in Control Panel of the card as a test to determine how this follow-up. I may also changed some settings in the console Windows, but I'm not sure. Unfortunately, unlike in versions previous OS, the Windows mixer table affect use of the sound card and it is possible that I got all inputs muted in the Windows mixer as a general precaution.

  Put the system into "sleep" (in the Start Menu) is done several times during my normal day. After running these tests of control, I found that the card does not work after that system was return of the mode 'sleep'. Immediately after the trials I reset control panel of the sound card for my normal use. All seems OK for audio operation was normal except after public awareness of Sleep Mode.

  Audio playback seemed normal in all applications. Programs appear to progress successfully through a recording during playback. Indicators like meters, position of playback cursor and displays the elapsed time has shown its normal operation, but nothing has reached the map output Sockets. I could not find any audio settings that seem to not correct. The Device Manager said that the card was working properly. Restart the normal audio returned BONE, as it does now (most of the time) for the keyboard.

  I played with things for two or three weeks. I've posted questions on some audio related forums, but no suggestion had no effect. Finally, I was ready to uninstall the card its and its drivers, then reinstall, when I remembered on the System Restore Points.

  I found there was a generated system restore point made a few hours before I did my test of the monitor-the-new-record. I used the restore point and the audio card to return to normal, the awakening with the rest of the system.

  The only thing I could say to be uninstalled by the restoration of the system has a few updates of Microsoft Security Essentials. I immediately did a manual update of that, to ensure it would not be any effect on the audio. Audio worked properly since registration, including, but I have not retested monitoring check against existing tracks.

  It was shortly after the keyboard problem has started. In this case I don't know what it is changed on the computer that could have led to the problem, but it seems not unlikely that some settings in the registry system is again wrong.

  Hello

  Thanks for posting your question on the Microsoft Forum.

  Receive you error messages, if so, what is the exact error message?

  What is the number and the model of the keyboard?

  I suggest you to follow the steps below and check if it helps.

  Method 1

  Try to start the troubleshooter from the link below and check if it helps.

  http://Windows.Microsoft.com/en-in/Windows7/open-the-hardware-and-devices-Troubleshooter

  Method 2

  I suggest you perform the clean boot.

  Put your system to the clean boot state helps determine if third-party applications or startup items are causing the problem. You must follow the steps in the article mentioned below to perform a clean boot.

  See the link to perform the clean boot.

  How to perform a clean boot in Windows

  http://support.Microsoft.com/kb/929135/en-us

  Note: Refer to "How to reset the computer to start as usual after a clean boot troubleshooting" under more information to prepare the computer to start as usual after a repair.

   

  Method 3

  For problems with the computer does not wake from sleep, see you at the suggestion of Leo Huang

  http://social.technet.microsoft.com/Forums/windows/en-US/0866de60-a16b-41c4-8a6e-b56c848478f3/new-computer-using-windows-7-will-not-wake-up-from-sleep-mode-i-have-to-manually-turn-it-off-and?forum=w7itprogeneral

   

  Please let us know if the problem persists. We will be happy to help you further.
  Thank you.

   

• Ivy Bridge not available in the list mode CVS when you activate CVS

  I have a new cluster for which I'm trying to activate CVS, no problem, allowing all the options in the list, with the exception of Ivy Bridge.  By clicking on the icon in the hosts Summary tab I see the Ivy bridge is indicated as compatible.  However, IVY bridge does not appear in the list of the EVC modes in the dropdown menu, what gives?

  Processor is Intel E5-2670 v2 (which is supposed to be fully compatible with IVY bridge and IVY bridge appears in the list of compatible modes in the contents of the host tab)

  What could be the problem here?    Why is sandy bridge later and more it is selectable in the menu... don't expect to see the same choices in the drop down as in the list of compatible modes?

  

  In vCenter Server 5.1 and 5.5, the Intel® option 'Ivy Bridge' generation appears only in the Web Client.

• Satellite P750 - Wireless disconnects when wake the portable computer from the 'standby mode '.

  Hey

  Today, my Toshiba Satellite P750 (running Windows 7) has been disconnected from my wireless network when I wake from sleep mode. When I close the lid of my laptop, it goes automatically into mode 'sleep', and when I open it, I put my user password and use it as usual. However for some reason any today, it does not work.

  When I wake up, it recognizes my wireless network is available, however, cannot connect to it. When I solve the problem, it indicates that there is a problem with my router and I should turn it off, wait at least 10 seconds and then turn it back on. I tried this and it works fine, but my laptop has never done that (in the few weeks I got it) and I wouldn't constantly reset my router to use Internet. In addition, I have another laptop at home that works very well.

  Should be really this issue be resolved quickly as I have exams this week.

  See you soon

  Hello

  Maybe there is a problem affecting the IP automatically once the laptop has been in sleep mode. It could also be another reason for it but it of always difficult to say which could affect wireless networking

  I think you should try to update the Wlan driver.

  Don't know exactly what you have but here the card Wlan, you can find all the latest WLan drivers available for Toshiba laptops:
  http://APS2.toshiba-tro.de/WLAN/

  Uninstall the old drivers first, after new reboot install new drivers downloaded for the wireless network card that is built in Notepad.

• Comp hangs upon the release of the standby mode

  I have a Pavillion g7 notebook comp running Windows 7. About a week after the expiration of the warranty he began to break down during the recovery from the sleep mode. Now, it crashes almost everytime. I tried to download updated drivers from HP.com, but it did not help. I would like to do a reinstall clean (don't know if it's exactly the right name for it) in which the model is returned to the State it was in when it was brand new, with the exception of save personal files in My Documents, my pictures, etc. The model did come with a disc to restore so I don't know how to do it. Thank you very much in advance for the help and be specific because I've never done this before.

  There are several ways to recover the OS to factory settings... Here we go.

  (1) Please try to run the f11 recovery that will install the operating system using the recovery partition. It's the best way to solve the problem. type just hit f11 when the turn on/off the computer. (Make sure that the recovery media is already created by you using Manager HP recovery for future use).

  (2) snack F11 does not work and that you have created the media, use your own recovert holder that was created on the same computer.

  (3) where no one (f11 and self created dvd/CD) work and you need to get the DVD from DVD HP. order HP and use them to re - install the operating system.

  This should help get the media.
  http://support.HP.com/us-en/document/bph07143

  Otherwise, please visit www.hp.com ; Select the country from the left of the bottom if you are outside the United States.

  now, please select "support and drivers" > now click on drivers & software > enter a model number of your computer. (if the list is populated in the case of similar models are there in this series, select the model you have)

  Select the operating system you have received this with computer and click Next > now, you should get an option "order recovery media - select it and under that you have the type of available media.» SELECT and the desired media.

  Incase you have problem ordering media; You can try after some time or contact support HP to get media ordered.

  also for the recovery of countries or products little online ordering is not available; in this case, the visit of the region/country ( www.hp.com and some countries). Click on connect with HP and HP. e-mail/phone support contact numbers are available, please call to place an order for your product in the country concerned (if available).

  I hope this can help, good luck!

• Utility profile WLAN does not start after the removal of some tools from Toshiba

  Here, I would like to say that Toshiba software (utilities, entering in laptops) is poor, unstable and mostly useless. I think it makes sense to launch a call to management of Toshiba to stop dealing us with the ugly such software.
  SHAME ON THEM!

  For example: in my new Toshiba laptop utility of LAN/WLAN profile (the program is useful only) did not work. It has not removed after uninstalling some of the Toshiba Utilities, their menu program shortcuts forms and I can also see their icons to the left in the notification area settings.

  In addition, some of the utilities did not start (like Toshiba disc Creator). Also utility Toshiba are very different, poorly described and localized, do not appear in between them and their shortcuts are entwined in the menu of programs with shortcuts to documentation.

  Hey Buddy,

  To be honest I don t understand why people post only the negative side of utilities Toshiba pre-installed you also noticed that they make your (computer) life easier?

  I don t want to count each tool of Toshiba, but they provide useful functions like CD burning, material is diagnosed, assistant LAN/WLAN connection and so far.

  If you don't like it, n no one said that should be used. Uninstall it and be happy with your laptop. :)

  Regarding your problem:
  I put t know why don t tool work harder because you don't l t post the exact name of it, and that the tools you deleted but say you ConfigFree? The program is useful for WLAN/LAN connections then try to reinstall Toshiba page.

• I bought a new external hard drive, but it does not appear in the library mode.

  One of my external hard drives is almost full. I would like to move some of the photos from the old to the new one that I just bought. The new external drive appears in Windows Explorer, but does not appear in Lightroom.

  I use Windows 7 and Lightroom CC.

  Hi Loyce1023,

  In order to see the most recent external drive in Lightroom, you must either import some images of the most recent disc.

  Or move some images of the old drive to the more recent, outside of Lightroom, and then reconnect the images from Lightroom.

  Kind regards

  Tanuj

• second monitor is not on after the "sleep mode"

  HI, I have an iMac of 2014 and an AOC monitor as a second screen, when my iMac goes into sleep mode and then re - wake up he does not recognize the AOC monitor and goes back to be one screen on the iMac. I have all the latest downloads and I am running OSX El Capitan

  What cable you use to connect to the screen. My friend had the same problem with a HDMI cable, it has opted for a thunderbolt cable and never had the problem again. Hope this helps, good luck to you,

  ~ Michael M

• YouTube does not pass to the hd mode full screen

  Hello
  I have YouTube value "always switch in HD when you switch to full-screen (if available)", but when you use the latest version of Firefox (4.0.1), this does not happen.
  I tried it in Chrome, and he works there, so it may be a problem with Firefox. Any suggsions?

  Clear the cache and cookies (for the site), and then try again.