WLC use Management Interface & more get started Questions

Similar Questions

• WLC 5508 management interface

  Hi, I have a design requiring a WLC 5508 be connected to two separate swithces specific wireless. WLC 1 port is connected to the switch A trunk and WLC Port 2 is connected to the switch B. Each switch has its own local VLANS. When I connect the years 1130 towers they need find the interface of management initially then only use management. AP interfaces since there is only a single management interface, if the assignment of management interface on a VLAN that is configured on the switch then APs on spend a fine join but those switch B continue to ask for the management interface and the version debug capwap on WLC he says that this query Join were received on the bad ineterface...

  the only work around that was to do the routing between switch A and switch B for both VLAN residing APs... but for security reasons - customer would like to avoid this

  any help is appreciated...

  Unfortunately, the initial discovery must arrive in the management interface.  Once this has happened the AP expected the second AP manager who is on the subnet of comments, therefore, they are able to stand.  But if the AP is restarted, it would need to discover once again and would fail.

  What is the concern of customers to have all routable network mgmt AP?  guest users can not see anything there.

  IMO, let the AP able to connect to the subnet of mgmt, but then put an ACL L3 upward, to block the subnet of comments to achieve anything in the internal network.

• WLC 5508 Management interfaces

  I'll put up a new 5508.  I have used the config of a 4402, have successfully connected to the path of Service to manage the device, but for some reason any cannot connect to the management interface.  In this case, port 1.

  The service port is connected to a catalyst switch and grabbed an IP (subnet 10.2.x.x) no problem.  I can access the 5508 via https using MS.  However, port 1 is connected to the same Catalyst switch, but on one vlan different (10.20.x.x subnet).  Both ends show that interfaces are in place, I can ping the interface from any other host on the network, but when I try to run the device via https I can't connect.  We use the WCS and I can't add the device to the WCS.  About all I can do is ping this interface.

  I probably forgot something very basic, but I'm stumped.

  We have the same Cisco 5508 controller and we discovered that if you use a computer on the same subnet that the Service interface, you won't not be able to connect to the management of a via HTTP or SSH, even though you 'll be able to ping. We changed the IP address of the service interface, and then we were able to connect to the management of a site.

• appvolume Setup is complete but get error below when opening the web app-volume Manager interface. Cannot start the volume App Manager "cannot load this file - tiny_tds.

  "failed to start volume App Manager" boot failure Unable to load the file of this type - tiny_tds

  

  Hi Paul amstaur,.

  This question says, I've met before, and there is a permission problem. Please do below things to get rid of.

  Since you have already installed the app volume, go back to the snapshot, or install a vanilla OS. Provide a sufficient permission in the local security policy, if you install SQL express as well as the volume of the app as the backup Administrator, debug as an administrator, log in as a service to the domain user. Also make sure the time is correct on the computer. You must restart the computer after you gave permission.  Most of the cases you already have full filled what mentioned above, but still you get an error.  To get rid of it, you must copy the appvolume installation files to the local directory, may be in the C drive and recommending only not to mount the ISO in virtual CD ROM, instead of copy and extract the ISO locally.  the next important thing is that you must run the setup.exe AppVolume run as administrator.

• LR3 Getting Started questions

  I am opening since v2 and I looking to spend 3 LR, but have some questions of functionality before buying LR.

  Right now, it is not designed as Aperture LR can, can't post.  It is intended to, LR has features that I love and is considering moving to it in the course of the opening, but what follows is a 'must - have' and I just want to know from a technical point of view, if I can do the same (similar) workflow in LR3.

  1 keywords: can I assign keywords via the keyboard?

  Opening

  Set of keywords: me, you, someone else

  Opt - 1 "Me" affects to selected images, Opt-2 'You' affects to selected images.

  Set of keywords: cat, dog, rabbit

  Opt - 1 will now assign "Cat" to a picture, Opt - 2 will assign 'Dog' to an image.

  The same concept can be done in LR?  If so, a link to a tutorial would be appreciated.

  2. smart Albums (Collections in LR)

  Opening

  I have a project with 100 images, in this project, I have 30 images in an Album1, 50 images in Album2.  Using Smart Album, I can create a rule that shows me that the 20 images that aren't in Albums (IE. Album1 or Album2)

  The same concept can be done in LR?  If so, a link to a tutorial would be appreciated.

  3 refenced vs Managed

  I have a library of reference in A3.  The files reside on external HARD disk (~ 100 GB), library (previews, keywords, etc.) resides on the internal HARD drive (~ 20 GB)

  Reason, I don't have that internal a HARD drive 120 GB.  Managed would not hold on my internal HARD drive.

  I added three images to a LR test, 2 MB each, and resulting in the Finder LR catalog file is about 3 MB.  Is the normal load of LR, about 50%.  If so, who does not work for me.  There are pre-sets to reduce the news file in LR?  Sense, previews low resolution, etc...

  4 drag-and - drop from the Finder

  Is there a way to drag - move pictures from the Finder to an existing catalog?

  1 keywords: can I assign keywords via the keyboard?

  Even the opening.

  Opt/ALT + n to assign the keyword-n (where n is a number from 1 to 9);

  Opt/ALT + 0 (zero) to scroll through the keyword sets.

  2. smart Albums (Collections in LR)

  Create a Smart Collection with the following rule: Collection contains not 'Album1"AND the Collection contains not 'Album2".

  3 refenced vs Managed

  Lightroom is not "managed", only "referenced".

  The size of the catalogue is growing mainly because of the cache of the preview, which is always located next to catalog (unless you use some hacks). Catalogue Prefs, you have options for preview quality (low, med, high), size (1024, 1440, 1680, 2048 on the long side) as well as the maximum time before you throw 1:1 previews.

  These 3MB is your catalog + hides the preview and probably some initial overhead for a catalog is empty (an empty database cannot be as small as 0KB).

  As a general rule, I think 1 MB per image for preview cache is a good hypothesis. So, a catalog of 50 k, you have 50 GB for the preview cache. The catalog itself must be less than 1 GB for this number of images.

  4 drag-and - drop from the Finder

  At least on Windows, it works fine. You drop the files and Lightroom opens the dialog box import with only the files that you gave up being selected for import, although the folder in the Finder/Explorer has more files.

• Getting started questions:

  If you start with a picture at 300 dpi, would be the puppet resolution should be 72 dpi?

  With the help of rotation full front - left - left - right head 3/4 3/4 and on the right the profile.

  You need 5 different heads, one of each location?

  Every head shall include all eyes behaviors for lip SNYC in all 5 heads?

  Do you want to use the same source (pivetpoint)? Hoew exactly would you assure a correct positioning?

  When you configure the lip SNYC, how can ensure you the positions of good mouth?

  Thank you

  by

  • I never tried to 300 dpi, but I would personally like 72 dpi for the performance of the only reasons (small size).
  • Yes, you need 5 different groups of head in your main folder of the head (see Wendigo in the example files). Currently in Preview 3, you will need to manually add the face and lip, synchronization to each head behaviors. In the snippet 4 to come, this will be automatic, and you will get two new modes - upwards and downwards.
  • Definition of a point of original head would affect all head positions inside the it - so I put only that one. When you make different heads, you will need to make sure that everything is aligned correctly (I often turn the visibility of the layer to simulate the transition to the PS or the ACE).
  • Big mouth to sync lip is a form of art in itself. If you search for "viseme of the comic strip" in a search of online image, you can see some examples of cartoons.

• Getting started Questions: 3

  Hi Ch members

  First of all, I want to thank the people who answered my questions in the past. The fact this is the first time that I've never used a forum, I didn't know how to tag 2 times the same question as well.

  
  

  Products Adobe have a feature that allows recording of keyboard and mouse strokes that would produce a computerized procedure step by step necessary to accomplish a specific task or group of tasks?

  
  

  I just watched episode 1 again. Dave had the character Cyberman in a normal state, moving his arms. Under the left arm has been key to 5. When Dave pushed BOTH hands turned to fists and went up to the waist. Has been the key only trigger in the left arm, but controlled both arms? If I intend 8 sets of hand for each arm positions, usually involving them both at the same time. Where would the triggers must be placed in the left or right arm or both? A simple arm movement should be placed in the arm proper only, right? My last questions covered this, but, but I really need to make sure that I understand this procedure.

  
  

  Is it possible to develop your layer structure in PS with the graphics included in the layers?

  
  

  Thanks again until the next time

  by

  I always put triggers KB in each layer I want control. If I want the left and right fist to move, always to the same trigger, I would use 'f' for each of them. But I might sometimes want to make them at the same time and sometimes individually. For this, I would choose triggers side by side on my keyboard. For example, 'f' for the right fist and 'g' the left fist. Then I could push the two triggers in the same time, or just one or the other separately.

  I hope this helps.

• Getting started Questions: 2

  I intend to have 8 hand sets. Example: thumbs up, thumbs down for the left arm and right as well.

  If I let the arm down in a position. When I join each hand must be in a new layer?

  But the arms stay in the original layer there?

  I plan to use buttons for the gestures of the arm. Example: 1 for both arms upward, with the thumbs up.

  2 for the arm upward with both thumbs down. It is on the right track?

  Thank you

  by

  Here's how to set up a new character:

  

  So I added the triggers with the keyboard option Hide brothers and sisters checked for each State of the hand. Each hit variations when the arm is bent/face somehow.

  If you wanted the arms together to pass key triggers too, then Yes, you need to include in the group as well. Basically, everything you put in a group can be exchanged with what level of the hierarchy even if you wanted to.

• Questions of getting started with Service contracts to small businesses

  I recently bought small business Service contracts for my Cisco Small Business networking products. I know that I get support 24 x 7, as well as the ability to open cases taken in charge (I recently tried and it works fine).

  I also know that I get next day material, as well as firmware upgrade replacement for my networking products.

  Here are my some "Getting Started" questions:

  1. If I need a replacement of material next day, how can I go to? Open a case of pension? I saw under the requests of support there is an option for the replacement of equipment.

  2 will I be automatically informed of updates firmware for my networking products, or I have to look it up on the Support Center? I don't know how to upgrade the firmware of all my networking products. Is it possible to subscribe to a list of email or RSS feeds notifying me of updates firmware for my networking products?

  3. I will announce when my service contract is about to expire so I can renew them, or is it my responsibility to do not forget to renew? I have to manually put on my calendar?

  Thank you!

  (1) to request an RMA number, you must open a case to the HWC.    You can call 866-606-1866 24 x 7 to prosecute.    If you do not have a support contract, (under warranty) you are only entitled to phone support 09:00-18:00 (local time) m..     You MUST be prepared to troubleshoot the device with the HWC engineer.     Do not assume you can open a file and receive an RMA number without looking at the camera.     Often, we can save the camera and make you save a lot of time.

  (2) you can sign up for automatic alerts on updates of the firmware using this link and by selecting the devices you want updates on.    The 2nd link allows you to manually check for updates.

  http://www.Cisco.com/Cisco/Web/support/index.html

  http://www.Cisco.com/Cisco/support/notifications.html

  (3) I checked with HWC contracts administrator.       According to her, you should begin to receive alerts from 6 months to 90 days before the expiry of the contract.    You may or may not be able to renew the contract, based on the life cycle of the product.

  In response to Dirk: you can extend the support of the product by buying a service contract any time during the period of 1 year warranty.     A support agreement for your device can be purchased from any local Cisco partner or any Cisco partner online.     Here are the main advantages of a contract on the guarantee.     They are a great value.

  • Extended telephone technical support from 1 to 3 years
  • Replacement of tip / the day following RMA return vs factory RMA
  • technical support 24 x 7 vs.  9. 6 M - business hour support F.
  • Firmware update
  • Even if your product my have a lifetime material warranty, which does not qualify for the technical / troubleshooting / configuration is supported without a contract.     With the warranty on the equipment only, the HWC troubleshoot your product just enough to know if it qualifies for a replacement of hardware.

• WLC 7.4.121.0 configuration management interface

  Hello.

  I have a problem Management interface IP setting in new 5508 controller. I get the error "error in the management interface IP configuration". I can't put a management controller IP.

  Start IPv6 Services: ok
  From Config Sync Manager: ok
  Start Hotspot Services: ok
  Starting the PMIP Services: ok
  Starting the Services of Portal Server: ok
  Starting the mDNS Services: ok
  Start Management Services:
  Web server: CLI: ok
  Web security: authentication certificate Web not found (error). If you cannot access the management interface via HTTPS please reconfigure virtual Interface.
  License Agent: ok

  (Cisco controller)

  Welcome to the Setup Wizard Cisco tool
  Use the '-' character of backup

  You wish to terminate autoinstall? [Yes]: -.
  Invalid response

  You wish to terminate autoinstall? [Yes]: no

  Name of the system [Cisco_bf:dd:c4] (31 characters max):
  AUTO-INSTALL: process completed - no configuration not loaded

  Enter administrative username (up to 24 characters): admin
  Enter the administrative password (3 to 24 characters): *
  Administrative password: *.

  Interface Configuration for IP [static] [DHCP] address service: no
  The service Interface IP address: 1.1.1.1
  Service Interface subnet mask: 255.255.255.0

  Enable aggregation LAG (Link) [Yes] [NO]: no

  The Interface IP address management: 192.168.10.1
  Management Interface subnet mask: 255.255.255.0
  Router default Management Interface: 192.168.10.10
  Error in the management interface IP configuration

  The Interface IP address management: 10.10.10.1
  Management Interface subnet mask: 255.255.255.0
  Management router default interface: 10.10.10.100
  Error in the management interface IP configuration

  Address IP Management Interface:

  ····························································································

  Did someone in the face of this issue?

  Thank you.

  Hello

  Try these:

  1. with the WLC, please the Frother (in SecureCRT or hperterminal) the value none. Once the changes are made, CLI will start to work as usual.

  2. Another common reason may be related to the configuration of the virtual interface of the controller. To resolve this problem, remove the virtual interface, and then re - generate with this command:

  WLC >config interface address 1.1.1.1 virtual

  Then restart the controller. After that the controller is restarted, re - generate the certificate webauth locally on the controller with this command:

  WLC >config certificate generate webauth
  In the output of this command, you should see this message: Web authentication certificate has been generated.

  Now you should be able to access the secure web mode of the controller to restart.

  3. try to use a diff for the service interface IP address do not use 1.1.1.1.

  Concerning

  Remember messages useful rates

• Questions on the WLAN and AP Manager interface

  Hello

  In fact, I was searching in the internet for more information on the (the AP Manager interface), I've only had the following link on the configuration of WLC.

  http://www.Cisco.com/en/us/docs/wireless/WCS/7.0/Configuration/Guide/7_0admin.html

  -If you have more information about this interface, share with me pls

  My second question is about the WLAN. In fact, I connected the AP lightness to the controller directly via a private network and configured WLAN with SSID. The question im face that customers can see the SSID, but can not be associated. I mean the packets sent is complete but the packets received too low, so I can't access the net.

  How can I solve this problem?

  Should I SWITCH to connect 3 AP light to the controller and the location device? or its just to connect these APs and the controller directly to our private network, because we use the same subnet.

  Thank you

  concerning

  Hello

  The link below can give u some info and you can be knowing this as well

  http://www.Cisco.com/en/us/docs/wireless/controller/5.2/configuration/guide/c52mint.html#wp1117288

  Then regarding the WIFI network... If you are able to see the SSID but not able to associate... What is the quthentication and the encryption is we help? We receive the IP or not?

  Private network means? the WLC will connect to the switch, right?

  Let me know if that answers your question...

  Concerning
  Surendra
  ====
  Please do not forget to note positions that answered your question and mark as answer or was useful

• Had a recent fall and rebuild and don't get 'My recent Documents' show more when 'Start' is clicked.

  Original title: my recent Documents

  Had a recent fall and rebuild and don't get 'My recent Documents' show more when 'Start' is clicked.

  Floowed instructions in 'HELP' to customize, Advanced and list but do not work.

  Help please.

  Thank you

  Bill

  Hi Bill,

  ·         What version of Windows XP you are using?

  If you are using XP Professional, follow these steps.

  Note: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following link.  http://support.Microsoft.com/kb/322756

  Step 1: Follow these steps:

  (a) click on Start and then run.

  (b) type gpedit.msc in the run box and press on enter.

  (c) in the Group Policy Editor, navigate to:

  User configuration > administrative templates > Start Menu and taskbar

  (d) double click on menu to delete Documents from the Start Menu.

  (e) select not configured.

  Step 2: Follow these steps:

  (a) click on Start then on Run.

  (b) type regedit.exe in the Run dialog box, and then press ENTER.

  (c) access: HKCU\Software\Microsoft\Windows\CurrentVersion\Policies\Explorer

  (d) right-click NoRecentDocsMenu to select change.

  (e) change the value to 0.

  (f) access: HKLM\Software\Microsoft\Windows\CurrentVersion\Policies\Explorer

  (g) right click NoRecentDocsMenu to select change.

  (h) change the value to 0.

  (i) leave the registry (Regedit.exe) editor.

• Failed to start Remote Access Connection Manager Service. Get the 20 error: the system cannot find the specified device.

  This seems to have started with the last batch of updates of Windows 7 (including SP1).
  I can't connect using dial-up.  Get the message:
  Cannot load the Remote Access Connection Manager service
  Error 711: The operation could not complete because it could not start the remote access connection manager service
  in time.  Please try the operation again.

  When I try to start the Remote Access Connection Manager service manually, I get the message:
  Windows could not start the service on Local computer remote access connection manager.
  20 error: the system cannot find the specified device.

  My phone displays the modem works properly, and telephony and the Secure Socket Tunneling Protocol service started.

  I don't know what else might have changed.

  Hello Vince_867,

  Thanks for your post.  Take a look at this thread for a possible solution to your problem.

  See you soon

• Use of the Trunk Ports (Cisco) on the management interface

  Hi all

  Background:

  We are in the process of consolidation of 2 farms of esx servers and will end up with 10 guests in a single cluster. Guests come from 2 VLAN separate (say 10 of VLANs and vlan 20). A test I took one of the hosts of HA/DRS and tests with it. For HA and DRS to work efficiently and properly in common all resources, we all want vm to leave both VLAN access to move to any host in the cluster.

  The test:

  My single host mentioned above, I created 2 groups of ports on a vswitch, vlan10 tag and with vlan20, I deployed a VM and tried on the two IP address ranges. It worked (with the correct settings of defined IP by VLAN) but as soon as we resources shared the port used by the management of network vmkernel port we lost the connection to the HOST from a management perspective. What the question is that it is possible to connect the management network a trunk port? We have 2 network interfaces connected to the vSwitch and both used for the VM traffic as well as management traffic. That's how they are currently implemented except that the switch port is on a VLAN-specific rather than shared resources.

  Thank you very much

  Chris

  Hi Chris

  Yes, the network management also accepts the vlan tagging/trunking.

  Just add the number VLAN on the Portgroup.

  Maybe you can do a printscreen with the current configuration?

• Dynamic management of the mobile AP management interface to another dynamic interface (WLC 2504)

  Situation/configuration is the following:

  -2504 WLC (8.1.131) with a total of 22 AP is connected.

  -Several WLAN active each with its own interface (dynamic)

  -L' (static) management interface is the option "Activate the dynamic management of AP" enabled.

  -The four physical interfaces of the WLC remain TROLLING configured.

  What is the problem:

  In the current configuration, the management interface is in the same vlan as the AP we now want to move the management interface to a different VLAN, but keep the AP in the vlan current. The idea is to move the management interface to its new vlan and disable "enable dynamic management of AP". Then, create a new interface (dynamic) in the same vlan as of AP and select 'turn on the dynamic management of AP' on this interface. Configure it as it is no problem but is does not work. The AP will record is no longer with the WLC.

  Is there something I may be missing why this does not work?

  Richard.

  Yes, that's the gist of it.

  I recommend always making a capture packets if only just for educational purposes and to see how this works in action. I found it interesting when I did in the lab here.