Failed to start Remote Access Connection Manager Service. Get the 20 error: the system cannot find the specified device.

This seems to have started with the last batch of updates of Windows 7 (including SP1).
I can't connect using dial-up.  Get the message:
Cannot load the Remote Access Connection Manager service
Error 711: The operation could not complete because it could not start the remote access connection manager service
in time.  Please try the operation again.

When I try to start the Remote Access Connection Manager service manually, I get the message:
Windows could not start the service on Local computer remote access connection manager.
20 error: the system cannot find the specified device.

My phone displays the modem works properly, and telephony and the Secure Socket Tunneling Protocol service started.

I don't know what else might have changed.

Hello Vince_867,

Thanks for your post.  Take a look at this thread for a possible solution to your problem.

See you soon

Tags: Windows

Similar Questions

  • Error 1068: the dependency service or group failed to start and failed to start the remote access connection manager service.

    Original title: Windows could not start the service of connection manager on the local computer remote access

    amplifier

    Windows could not start the service of connection manager on the local computer remote access

    Error 1068: The dependency Service or group could start.

    Hi sunelchandraoli,

    1. when exactly you receive this error?

    2. you remember to make changes to the computer before this problem?

    Step 1:

    "Make sure that all the services of the dependence of the"Remote Access Connection Manager"" are launched in the list of services...

    a. Click Start, type services.msc in the box start the search.

    b. select Services from the list programs. If you are prompted for an administrator password or a confirmation, type your password or click on continue

    c. right click on the Remote Access Connection Manager service and then click Properties.

    d. under the general tab, click Manual next to startup type.

    e. under the general tab, click Start under the service status and then click OK.

    f. also check for long-term services.

    The dependency of 'Remote access connection manager' services include:

    i. secure Socket Tunneling Protocol Service

    II. telephone

    III. Plug-and-Play

    IV. Remote Procedure Call (RPC)

    c. of DCOM Server process Launcher

    VI RPC end point mapper.

    Make sure that the above services are started in the services list. If this is not the case, start all services above and check.

    Step 2:

    You can also try a system restore to a prior restore point you have been affected by the issue.

    Note: When you perform the system restore to restore the computer to a previous state, programs and updates that you have installed are removed.

    To run the system restore, you can consult the following link:

    System restore

    http://Windows.Microsoft.com/en-us/Windows7/what-is-system-restore

    System Restore: frequently asked questions

    http://Windows.Microsoft.com/en-us/Windows7/system-restore-frequently-asked-questions

    Hope this information is useful.

  • Why can't I start Remote Access Connection Manager

    I am not able to connect to internet using my 3G Broadband. I try to resolve the status of the remote access connection manager to "on the road", but the error message invites up to said "Windows could not start the service on local computer remote access connection manager. Error 1068: the dependency service or group could start. "I find the dependencies are Remote Access Auto Connection Manager, routing and remote access, Sharing (ICS) to connect Internet. I tried to put those 3 to "started", but was able to start also.

    Hello
     
    You must make sure that the underside of services are started and restart your computer and check if the problem is resolved.
     
    To start the services.
     
    1. click on start.
    2. type Services.msc in the search box and click on enter.
     
    Note: the common addiction for "Remote Access Connection Manager" and 'Remote Access Auto Connection Manager' is 'Secure Socket Tunneling Protocol Service'.
     
    Make sure that you check the properties of service no matter what you try to start, then click the dependency tab and make sure that you select the dependency registered under this service services.
     
    The dependency of 'Remote access connection manager' services include:
     
    a. secure Socket Tunneling Protocol Service
    b. phone
    c. Plug-and-Play
    d. remote Procedure Call (RPC)
    e. DCOM Server process Launcher
    f. RPC end point mapper
     
    Make sure that you try to start the Connection Manager Service dependency services automatic remote access as well.
     
    Method 2:
     
    I recommend you to update the drivers and see if it makes a difference. You must be logged on as administrator to perform these steps.
     
    1. open Device Manager by clicking the Start button, click on the Control Panel, clicking system and Maintenance, and then clicking Device Manager. If you are prompted for an administrator password or a confirmation, type the assword or provide confirmation.
    2. in Device Manager, locate the device, and then double-click the device name.
    3. click Driver tab, then click on set to update driver and follow the instructions.
     
    Try to follow the link provided to update a hardware driver that is not working properly and check the question below.
    http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

    Thank you, and in what concerns:
    I. Suuresh Kumar - Microsoft technical support.

    Visit our Microsoft answers feedback Forum and let us know what you think.

  • Can not get to start remote access connection manager and the connections don't work Internet

    Original title: wired & wireless connections does not.

    I can not get the remote access connection manager to start and so no internet connection is not working, also I can't open the system restore to go back on this machine. What is this?

    I am running a Dell Studio 1735 PP31L w model number / Edition Vista Home premium.

    Hi Rick,

    1. what happens when you try to start the remote access connection manager? You receive messages or error codes?

    2. you receive error codes or restore messages when you perform the system?

    You can check the status of the following services and make sure that the services are started.

    a. Click Start and type Services in start search and press ENTER.

    b. in the services with the right button on the phone and then click Properties.

    c. under the general tab, select automatic next to startup type.

    d. under the general tab, click Start under the service status and then click apply and then click OK.

    e. Repeat steps c & d to the remote access connection manager and Remote Access Auto Connection Manager service.

    Hope this information is useful.

  • Failed to start remote access service

    Hello

    I get a vps and I install ca and iis and the remote access service

    I allow it as a vpn server

    When I try to run the remote access service there gives me an error

    The Routing and remote access is dependent on the Remote Access Connection Manager service, which could not start due to the following error:

    The dependency service or group was able to start.

    I reslove this problem to run these commands:

    netcfg u ms_sstp

    netcfg - c p-i ms_sstp.

    net start sstpsvc

    net start rasman

    now when I am tempted to throw there gives me this error:

    The Remote Access Connection Manager service terminated with the following error:

    The system cannot find the specified device.

    So what is the problem?

    Thank you.

    Hello

    Your question of Windows is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the Microsoft TechNet forum. You can follow the link to your question:

    http://social.technet.Microsoft.com/forums/en-us/categories

  • When I try to start the Remote Access Connection Manager in services.msc, the service will not start.

    Rick2425

    When I try to start the Remote Access Connection Manager in services.msc, the service will not start. I get the same error: "Windows could not start the service of connection manager on the local computer remote access: Error 1068: the dependency service or group could start."  Also, I can not restore the system to come and let me run it.

    It is a Dell PP31L, which belongs to a friend who does not connect to the internet because of these error messages.

    Hello Rick2425

    See the thread below and let me know if it helps thanks.

    http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-networking/error-1068-remote-access-connection-manager/b5155a8a-671e-4d11-8a99-deadc7aee8a1

  • The remote access connection manager could not start. Error 2: cannot find the specified file.

    I've updated from vista to the most recent update.

    I have windows vista Home premium 32-bit.
    I want to get this matter resolved without having to reinstall as I have a few games installed it on this system.
    The modem is not the issue as other computers connect very well.
    Thanks for the help from Microsoft.
    Recently, I tried to connect to the internet but that was not possible, because no connection could be established. The remote access connection manager does not start 2 error: could not find the specified domain. the RasMan-dependent services are started, but Manager logins remote does not start.

    Hi Mundilfar,

    You can try the folliwng steps and see if it helps.

    Step 1:

    You can try to scan the file system [SFC] checker on the computer that will replace missing or corrupt files & check if the problem persists.

    For more information, you can consult the following link.

    How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

    Step 2:

    If you are always faced with the question, then you can try to give permission for the Rasman registry key and see if it helps.

    Important: The following steps show you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs.

    For more information about how to back up and restore the registry, follow the steps from the link below:

    Back up the registry

    a. Click Start, type regedit in the search box and press ENTER.

    b. Locate the following subkey:

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\RasMan

    c. right click on the key and click Permissions.

    d. Select Advanced, click on owner tab, click your user name, and check the 'Replace owner of subcontainers and objects', click Apply - click OK.

    e. click the user or group name that you want to work with.

    f. check allow total control. Click apply and then click OK.

    g. restart the computer and check.

    Hope this information is useful.

  • Error 711; Remore access connection manager service will not start

    Error 711; Remore access connection manager service will not start

    Hello

    Thanks for posting your question in the Microsoft Community!

    When exactly do you get the error message?

    This error message appears when a required service is not started on your computer. You won't be able to connect to a network, and you might not be able to install network cards.

    This problem may occur if some or all the following services are not started:

    • Plug-and-Play
    • Remote Access Auto Connection Manager
    • Remote Access Connection Manager
    • Telephony

    You can see test link following the steps and check:

    Get help with "Error 711" message

    http://Windows.Microsoft.com/en-us/Windows7/get-help-with-Error-711-message

    Do not post the State of the question.

    You can always view in Microsoft Community if you need help with Windows.

  • Remote Access Connection Manager

    What is Remote Access Connection Manager and what is it?        PS. I don't know what Windows topic category and applications, this falls under, but since I HAD to choose one...  Thank you for your help.

    Hi bjeja,

    Welcome to the Microsoft community where you can find all the answers related to windows.

    Remote Access Connection manager manages connections dial-up and virtual private network (VPN) from the computer to the Internet or other remote networks.

    If you have questions about Windows do not hesitate to answer and we will be happy to help.

  • HP connection manager: Fatal Error, HP Connection Manager Service has stopped responding.

    Hey there,

    I have a very big problem with HP Connection Manager 4 on several Windows 7 laptops. The program is installed on about 250 laptop computers and some of them drive me crazy. Everything was fine until some point (I'm not quite sure, that could be after the installation of SP1, Win7), the connection manager has decided to stop working on some machines. Whenever I try to start it, it takes a long time to load until the following message is displayed:

    "HPConnectionManager.exe - fatal error '.

    HP Connection Manager service has stopped responding. Quit and restart the application.

    A fatal error occurred, check the HP connection manager in the event viewer for more details.

    Recovery of the factor of COM class for the component with CLSID {24DB46C8-C842-4E91-9AC4-8A9525A5551D} failed due to the following error 80080005. »

    I tried the following on one of these books:

    -Start the service manually: "Error 1067: the process terminated unexpectedly."

    -Msconfig: Removed any connection associated with Autostart Manager

    -Reinstall the HP connection manager

    -Repair HP Connection Manager

    -Reinstall .NET 3.5

    -Changed some regkeys

    -Install Microsoft Hotfix KB2519740 which is part of the system essential updates for Microsoft Windows 7 (that I can't download because there is a server error)

    More information:

    -(pour la plupart) HP Probook 6550 b

    -Windows 7 Enterprise 64-bit, SP1 (English and German MUI)

    -HP 4.1.22.1 Connection Manager

    The only thing that really works is to reinstall the laptop with the image with which we install all of them. HP connection manager is installed as a software later so I don't understand why a reinstall is successful.

    I'm really tired of this problem, and I have a few unhappy customers on my back, so if you have any suggestions for me, please help.

    Thanks in advance!

    You could try this on one machine that shows the issue and see if it helps:

    Relevant information:

    V4.4.10.1 Connection Manager

    Corrections in sp58930:
    -Fixes an issue where the setting of HP Connection Manager protocol PAP (Password Authentication) in the connection profile for Verizon LTE systems causes an authentication failure of network systems in some markets.
    -Fixes an issue where HP Connection Manager is not displayed in the configuration of the HP software.
    -Fixes an issue where event viewer displays an error in the HP Connection Manager once the system is restarted.
    -Fixes an issue where the HP Connection Manager displays the error message "SIM card is locked" when a PIN has been used successfully to unlock the SIM card.
    -Fixes an issue where the "Enter PUK" (Personal Unblocking Code) button does not appear in the HP connection manager when a SIM has been locked after the PIN code has been entered incorrectly.
    -Fixes an issue where the statutes of the wireless LAN and Bluetooth device not display correctly on the HP connection manager when Connection Manager is started while the wireless LAN and Bluetooth are turned on and connected.
    -Fixes an intermittent issue where network technology is incorrectly identified.
    -Fixes a problem that causes a HP connection manager to stop working and an error message is displayed.
    -Fixes an issue with the Spanish version.

    Prerequisites:
    • HP or Compaq machines only brand
    • Operating system is Windows XP or later
    • If the operating system is Windows XP, it must have installed SP3
    • Version of the .net framework 3.5 SP1 must be installed

    Improvements:
    -Supervises HP Support version 4.6.8.1

    Installation package:

    sp58930 Connection Manager V4.4.10.1

    =====================================================================================

    Hope that helps...

  • Receive an error message that the HP Connection Manager service not installed

    Original title: Application of program compatibility... I get a box that says. Service not installed HP connection manager... so it says incompatible... How can I fix it?

    This box appears whenever I start my computer...

    Hello

    1. what version of Windows you are using (Windows XP, Vista, 7)?

    2 did you change on your computer before the show?

    Follow the steps mentioned below:

    Method 1:

    Step 1: Run in SafeMode networking

    Safe mode, start Windows in a limited State, where only the essential is started. If a problem does reappear when you start in safe mode, you can eliminate the default settings and basic device drivers and services as causes possible

    Start your computer in safe mode with networking

    http://Windows.Microsoft.com/en-us/Windows7/advanced-startup-options-including-safe-mode

    Step 2: Perform the clean boot

    A clean boot helps eliminate software conflicts. The article below describes how to solve problems in Windows 7 by performing a clean boot. This article also describes how to start the Windows Installer service and how to reset the computer so that it starts as usual. To configure your computer to clean boot see the following link.

    How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

    http://support.Microsoft.com/kb/929135

    Note: When you are finished troubleshooting, follow step 7 in the article to start on normal startup.

    If the problem persists, follow the next method

    Method 2:

    Let us try to reinstall the HP connection manager and check with the question.

    HP Connection Manager service

    http://h30434.www3.HP.com/T5/notebook-operating-systems-and/HP-Connection-Manager-service/TD-p/891309

    It could be useful!

  • Not able to start the Windows firewall/internet connection (ICS) service on the local computer for sharing

    It is said

    ERROR 2: THE SYSTEM CANNOT FIND THE SPECIFIED FILE

    When you try to manually start the Service. !

    System log gives:

    7035 (service has been successfully sent a start control.)

    7036 (service entered the stopped state.)

    7023 (the Windows Firewall/Internet Connection Sharing (ICS) service terminated with the following error:)
    The system cannot find the specified file. )

    Where is the specified file (which newspaper where)... ?  If I have a lack or a file corrupted how can I overwrite this file by a valid... ?

    Any help appreciated

    NVM...

    Its a Virus Rootkit,

    Download the (free) Rootkit in Kaspersky killer

    http://support.Kaspersky.com/downloads/utils/TDSSKiller.zip

    Simple to use... Unpack... then

    Run... (Note disable any local Antivirus that is running)...  TDSSKiller.exe

    * Access to the restored Winupdate site, Miss-Direction has stopped.

    * Updates Windows restored.

    ICS Windows Firewall/Internet (ICS) personnel started successfully

    Thanks to "Joyce Liang (MS) Windows Update Support"

  • The MCSTRM service failed to start due to the following error: the system cannot find the specified file

    My computer starts rather suddenly gel with many applications.  Today it froze again once I finished a long email and was about to send.  I lost him of course.  My Event Viewer was the topic.  Event 7000, Service Control manager Eventlog.

    What can I do?  I have Vista SP2 64-bit.

    I'll add that the kernel_driver of Type 1 mcstrm following 1 State arrested Win32_exit_code 2 <0X2>Wait_hint Checkpoint 0 x 0 0 x 0

    Please... any help to fix... my computer keeps freezing. and I will need to get a new laptop or an Ipad, if the problem persists.

    Thank you

    Candy C:\Users\David> net helpmsg 2

    The system cannot find the specified file.

    Is that error on this post code, IE something deleted, probably your antivirus or you.

    For problems to explore, which has nothing to do with this post, try this (which covers almost any problem).

    Explorer

    Explorer (explorer.exe) is the program that is the start menu and taskbar, windows folder and the office (which is a folder window).

     

    To see if a fix is available

    In Control Panel (and select Classic discovered in the left pane) select reports on the problems and Solutions (problem of type in the START search box), go to historical problem, right-click of your error and choose check for the Solution.

    You can also right-click and choose Details for more information. Post these details here. The name of the Module fault is important information.

    If the problem affects Panel press the Windows key + R and type wercon (or type it at a command prompt).

     

    Close the browser and start a command prompt

    • Close Windows Explorer
    • Start - All Programs - Accessories - right on command prompt and choose run as administrator.
    • Click Start. Ctrl + Shift + Right-click on an empty spot (just above the power of buttons is one place) then Exit Explorer.
    • Press Ctrl + Alt + Delete then Task Manager.
    • Control all processes to explore are closed. On the process tab select explore and right-click and choose end process, repeat if more of an Explorer in the list.

    Then to restart the Explorer after trying all of the following

    • Press Ctrl + Alt + Delete and choose Task Manager
    • In the Task Manager, click the file menu and then click new task (run) and enter explorer
     

    If you cannot start the Explorer at all

    • Press Ctrl + Alt + Delete and choose Task Manager
    • Under the processes tab, click Show processes from all users to elevate to administrator
    • In the Task Manager, click the file menu and then click new task (run) and type cmd
    • Other things you can try typing

      Explorer
      Explorer c:\
      Explorer/e, c:\
      wercon
      control
      Iexplore
      Rstrui

    If you cannot start a folder window you can use the Browse button in the new task dialog. Don't forget that you must right click and choose Open rather than double-clicking.

     

    Reregister the shell registry entries

    It is important that each order is accepted. If the command fails it means the file is damaged and must be repaired.

    Close the Explorer like above and then type at the command prompt (or copy and paste by clicking in the command prompt window and choose Paste).

    regsvr32 /i shell32
    regsvr32 /i urlmon.dll
    regsvr32 RPCRT4.dll
    regsvr32 PROPSYS.dll
    regsvr32 MSCTF.dll
    regsvr32 cscui.dll
    regsvr32 rsaenh.dll
    regsvr32 timedate.cpl
    regsvr32 ATL DLL
    regsvr32 OLEACC.dll
    regsvr32 actxprxy.dll
    regsvr32 USERENV.dll
    regsvr32 msshsq.dll
    regsvr32 NaturalLanguage6.dll
    regsvr32 thumbcache.dll
    regsvr32 WINTRUST.dll
    regsvr32 MMDevAPI.DLL
    regsvr32 audioses.dll
    regsvr32 audioeng.dll
    regsvr32 ExplorerFrame.dll


    regsvr32 msi.dll
    regsvr32 FirewallAPI.dll
    regsvr32 netshell.dll
    regsvr32 pnidui.dll
    regsvr32 QUtil.dll
    regsvr32 c:\windows\system32\wpdshserviceobj.dll
    regsvr32 WINHTTP.dll
    regsvr32 C:\windows\system32\qagent.dll
    regsvr32 C:\windows\system32\portabledeviceapi.dll
    regsvr32 wbemprox.dll
    regsvr32 wbemsvc.dll
    regsvr32 fastprox.dll
    regsvr32 imapi2.dll
    regsvr32 wshext.dll
    regsvr32 gameux.dll
    regsvr32 msxml6.dll
    regsvr32 vbscript.dll
    regsvr32 jscript.dll
    regsvr32 wshext.dll
    regsvr32 wshom.ocx
    regsvr32 wshcon.dll
    regsvr32 scrrun.dll

     

    Delete the folder and the settings of the Menu

    This will remove the settings are saved for each file that you visit. Also the order of the start menu and pinned list settings.

    Close the Explorer like above and then type at the command prompt (or copy and paste by clicking in the command prompt window and choose Paste).

    Reg delete "HKCU\Software\Classes\Local Settings\Software\Microsoft\Windows\Shell" /f

    Reg delete "HKCU\Software\Microsoft\Windows\CurrentVersion\Explorer\Streams" /f

    Reg delete "HKCU\Software\Microsoft\Windows\CurrentVersion\Explorer\StuckRects2" /f

    Reg delete "HKCU\Software\Microsoft\Windows\CurrentVersion\Explorer\StartPage" /f

    Reg delete "HKCU\Software\Microsoft\Windows\CurrentVersion\Explorer\MenuOrder" /f

    Delete the thumbnail and icon Caches

    Close the Explorer like above and then type at the command prompt (or copy and paste by clicking in the command prompt window and choose Paste).

    attrib - r s h '% userprofile%\AppData\Local\*.db '.

    attrib - r s h '% userprofile%\AppData\Local\Microsoft\Windows\Explorer\*.db '.

    del "% userprofile%\AppData\Local\*.db".

    del "% userprofile%\AppData\Local\Microsoft\Windows\Explorer\*.db".

    Disable thumbnails and previews

    Damaged documents and particularly corrupt pictures or videos, can cause Explorer crash all trying to generate a thumbnail or an overview. This miniature and previews active option off.

    If you can start the Explorer, previews is Union on the command - folder and Search Options - framework of tasks use classic Windows foldersbar.

    Thumbnails are organized on the command bar - folder and Search Options - view tab - and check under Advanced settings - always show icons, never thumbnails and uncheck Show icon file in the pictures.

    If you cannot start the Explorer close Explorer as above and then type at the command prompt (or copy and paste by clicking in the command prompt window and choose Paste).

    Tracking Add "HKCU\Software\Microsoft\Windows\CurrentVersion\Explorer\Advanced" v "IconsOnly" /t Reg_DWord /d 00000001 f

    Tracking Add "HKCU\Software\Microsoft\Windows\CurrentVersion\Explorer\Advanced" v "ShowPreviewHandlers" /t Reg_DWord /d 00000000 f

    Tracking Add "HKCU\Software\Microsoft\Windows\CurrentVersion\Explorer\Advanced" v "ShowTypeOverlay" /t Reg_DWord /d 00000000 f

    Turn around after testing the Explorer.

    Tracking Add "HKCU\Software\Microsoft\Windows\CurrentVersion\Explorer\Advanced" v "IconsOnly" /t Reg_DWord /d 00000000 f

    Tracking Add "HKCU\Software\Microsoft\Windows\CurrentVersion\Explorer\Advanced" v "ShowPreviewHandlers" /t Reg_DWord /d 00000001 f

    Tracking Add "HKCU\Software\Microsoft\Windows\CurrentVersion\Explorer\Advanced" v "ShowTypeOverlay" /t Reg_DWord /d 00000001 f

     

    A boot is a way to explore

    It can be caused by a shell extension.

    Explorer (explorer.exe) is the program that is the start menu and taskbar, windows folder and the office (which is a folder window).

    The Explorer is built on addin programs called Extensions of Shell. The standard is provided by Microsoft, but programs add their own.

    • Download Autoruns http://technet.microsoft.com/en-us/sysinternals/bb963902.aspx
    • Close Windows Explorer
    • Start Autoruns by right-clicking and choose run as administrator
    • Click on the menu Options - Filter Options and check hide Microsoft entries and disable include empty locations
    • Go to the Explorer tab and uncheck everything to the left.
    • Click Start. Ctrl + Shift + Right-click on an empty spot (just above the power of buttons is one place) then Exit Explorer.
    • Press Ctrl + Alt + Delete and choose Task Manager.  Control all processes to explore are closed. On the process tab select explore and right-click and choose end process, repeat if more of an Explorer in the list.
    • Click the file menu and then click new task (run) and enter explorer

    If this can help, reactivate ½ at a time to identify those who. If this does not help, restart AutoRuns and go to the all tab and uncheck everything that it and restart. If this can help, reactivate ½ at a time to identify those who.

    Run Microsoft Fixit

    Microsoft has a range of automatic programs to solve common problems. To see problems explore

    http://support.Microsoft.com/mats/windows_file_and_folder_diag/en-us

    For the visit of the list the most comprehensive

    http://support.Microsoft.com/FixIt/en-us

    When you choose to download, choose the option to run on another computer. You can then save it to your hard drive. Open the folder, open the folder fix this laptop and run Run Fix It. It will contain all 27 FixIt.

    Recycle Bin
     
    If the problem is the trash bin remove the storage folders. It will be automatically re-created next time you delete a file or open the Recycle Bin. It will remove the trash and the files it contains for all users.
     
    Close the Explorer like above and then type at the command prompt (or copy and paste by clicking in the command prompt window and choose Paste).
     
    RD C:\$RECYCLE. BIN/s/q
     
    then repeat for each drive to change the drive letter, for example
     
    d:\$recycle Rd. BIN/s/q
     
    e:\$recycle Rd. BIN/s/q
     
     
    If the Office does not start
     
    This will create a new empty by user and common desktop computer. This will allow to test if a file on your desktop to start the Explorer.
     
    Close the Explorer like above and then type at the command prompt (or copy and paste by clicking in the command prompt window and choose Paste).
     
    MD "% userprofile%\DesktopTest".
     
    Add reg "HKCU\Software\Microsoft\Windows\CurrentVersion\Explorer\User Shell Folders" / v/t desktop REG_EXPAND_SZ /d "% USERPROFILE%\DesktopTest" /f
     
    MD "% public%\desktopTest".
     
    Tracking Add "HKLM\Software\Microsoft\Windows\CurrentVersion\Explorer\User Shell Folders" v "Common Desktop" REG_EXPAND_SZ /d "% Public%\DesktopTest" t f
     
    To restore default after having tested if begins to explore.
     
    Set ExpFix1 = % user
     
    Set ExpFix2 = % profile
     
    reg add "HKCU\Software\Microsoft\Windows\CurrentVersion\Explorer\User Shell Folders" / v/t desktop REG_EXPAND_SZ /d "% ". ' ExpFix1 ExpFix2%% \Desktop "/f
     
    Set ExpFix1 = % Pub
     
    Set ExpFix2 = % lic

     
    reg add "HKLM\Software\Microsoft\Windows\CurrentVersion\Explorer\User Shell Folders" /v "Common Desktop" /t REG_EXPAND_SZ /d "% ". ' ExpFix1 ExpFix2%% \Desktop "/f
     
    You will need to disconnect then.
     
     
    New entry missing folder
     
    If the above does not help.
     
     
    Click Start - All Programs - Accessories - right on command prompt and choose run as administrator. Type Regedit menu and file - import , import the NewFolder.reg.
      

  • I get an error saying "the BCM42RLY service failed to start due to the following error: the system cannot find the file specified. '.

    Log name: System
    Source: Service Control Manager
    Date: 17/07/2011-21:12:53
    Event ID: 7000
    Task category: no
    Level: error
    Keywords: Classic
    User: n/a
    Computer: ivan-PC
    Description:
    The BCM42RLY service failed to start due to the following error:
    The system cannot find the specified file.
    The event XML:
     
       
        7000
        0
        2
        0
        0
        0 x 80000000000000
       
        203523
       
       
        System
        Ivan-PC
       
     
     
        BCM42RLY
        %%d Ko
     
    original title: can someone please help...

    Hello

    1. you are using a Dell computer?
    2. What is the model number of your computer?
    3. don't you make changes to your computer before the problem?

    BCM42RLY is a broadcom driver. I suggest that you uninstall and reinstall the drivers.

  • Remote Desktop Connection Manager tree at startup

    I have install Remote Desktop Connection Manager 2.7 on a new PC.  On my PC before, when I started RDCMan, the tree of the server displayed automatically even if the auto masking has been enabled.  However, with my new installation, the tree is not displayed on startup.

    How to set up the tree to display when you start RDCMan?

    Hello

    As you have problems with ' Remote Desktop Connection Manager ' , we ask to view the query in the following forum.

    Windows 7 IT pro

    Hope this information helps.

Maybe you are looking for