WLS 10.3.2

Similar Questions

• Requested sample clock source is invalid wls-9163

  My goal is to use two accelerometers that using the NI 9234 entry of the modules and wireless wls-9163 chassis.

  My program is attached. Here is a photo in case you do not want to download the attachment: http://www.imagebam.com/image/577a4a195651371.

  The slave device is not able to use the sample clock that came out of the master on PFI1.
  I looked through the wireless DAQ resource kit and watched the following video:

  http://www.YouTube.com/watch?v=g_8jiKuKeDI

  and ive read this: http://zone.ni.com/devzone/cda/epd/p/id/6124

  I am aware that

  I also tried to synchronize two cDAQ-9178 using the same methods. I always get the error "required sample clock source is not valid.

  The manual says it should be able to do this

  http://www.NI.com/PDF/manuals/372488c.PDF

  Any help would be greatly appreciated.

  Vexis,

  Unfortunately, at the moment, you cannot synchronize the modules that use adelta-sigma converter (such as the NI 9234) in several cDAQ chassis. This is because these modules use a clock of sampling, which is very high; the PFI lines are unable to return to the required sample clock. You can share the start triggers, but the clocks of individual modules will drift over time.

  The reason that the error message says that "requested the sample clock source is not valid" is because these modules require the use of a sample of clock that comes inside a time base clock oversampling.

  Sorry for the bad news!

  Katie

• HAVE sampling frequency is divided by the number of channels + 1 for simulated ENET-9213, WLS-9213 and USB-9213

  Hello

  In the code in the example attached, I create a task with a single channel of AI.

  I get the maximum sampling frequency using DAQmxGetDevAIMaxSingleChanRate (or DAQmxGetDevAIMaxMultiChanRate), both return the same value of 1351 s/s.

  When I try to configure the sample calendar using DAQmxCfgSampClkTiming at the maximum sampling frequency clock he does not accept the rate and returns the following error. Note that the error message shows 2 channels, even if only a channel has been added.

  OUTPUT:
  DAQmx error:
  Sampling frequency is greater than the maximum sampling frequency for the number of specified channels.
  Reduce the sampling frequency or the number of channels. The increase in the conversion rate or
  reduce the time of the sample can also mitigate the problem, if you define one of them.
  Number of channels: 2
  Sampling rate: 1.351351e3
  Maximum sampling frequency: 675.675676

  Why the device driver thinks I have 2 channels in the task, when a channel has been added?

  Please find the code to reproduce this problem attached.

  Kind regards

  whemdan

  The MathWorks

  Hello w,

  By default, the ENET/WLS/USB-9213 in NOR-DAQmx module has the AI. AutoZeroMode the value of the DAQmx_Val_EverySample property. This causes NOR-DAQmx acquire the channel of the internal path of the unit (_aignd_vs_aignd) on each sample to return more specific measures, even if the operating temperature of the device moves over time. If you need the sampling frequencies higher than this allows, you can call DAQmxSetAIAutoZeroMode(..., DAQmx_Val_Once) (who acquires the formatting string when you start the task) or DAQmxSetAIAutoZeroMode(..., DAQmx_Val_None) (which disables the setting entirely).

  Note that for measures by thermocouple with cold junction compensation sensor of the 9213 NOR, NOR-DAQmx acquires channel built-in CJC (_cjtemp) on each sample as well, for the same reason.

  Brad

• Sampling frequency of HAVE is incorrect for simulated ENET-9213, WLS-9213, and USB-9213

  Hello

  ENET-9213, WLS-9213 simulation and devices USB-9213, I'm able to correctly get the sampling frequency of I = 1351 samples/s using DAQmxGetDevAIMaxSingleChanRate, which is incidentally on the value of spec'ed of 1200 s/s.

  However, when I create a task and add a voltage channel and then HAVE the sampling frequency of the task of query, I get a sampling rate of only 9 samples/s. I tried the same code with other devices and I get the sampling frequency corresponding to the device data sheet, it seems THST this problem is limited to 9213 devices.

  Why sampling returned by the task using DAQmxGetSampClkMaxRate rate returns than 9 s/s.

  And why the rate of conversion of DAQmxGetAIConvRate only 18 s/s.

  I enclose the test code which may be used to reproduce this problem.

  Kind regards

  whemdan

  The MathWorks

  Hello

  When I tried this with a USB-9213 simulation, I used the Sample clock Max Rate, as well as the Rate.vi of AIConvert:Max property node.  I could see that for 1 channel, I could spend up to 675.67/s, and I couldn't for 16-channel get79.49S/s (which total is equal to 1271 S/s, which is in the specifications).  The multichannel and single channel, I could get an AIConvert Max Rate of 1351.35.

  Something that could happen is that you do not explicitly set this device runs in mode high speed.  You'll want to set the property Get/Set/rest AI_ADCTimingMode channel at high speed, and you should see much better results in this way.

  Something else to note - I use DAQmx 9.0

• WLS-9163 and 9211, sampling frequency of evil?

  Hello!

  I have a WLS-9163 with 9211 mounted module. I have connected a single thermocouple type K to the analog input 0.
  I can connect and perform measures wireless. However, I can make only 7 s/s without error message.
  I get the following error message when I try to taste 14 s/s in the configuration of WLS-9163.

  Error-200081 occurred to the DAQ Assistant
  Possible reasons:
  Sampling frequency is greater than the maximum sampling frequency for the number of specified channels.
  Reduce the sampling frequency or the number of channels. The increase in the conversion rate or reduce the period of the sample can also mitigate the problem, if you define one of them.
  Number of channels: 2
  Sampling rate: 14.000004
  Maximum sampling frequency: 7.142857
  Channel name: _WLS-14049AF-2/_cjtemp

  When I use the 9211 in a cDAQ-9172 configuration I can acquire up to 14 s/s of a single channel with no problems at all.

  Somehow he thinks that I chose to take measures to channels, that is not the case.

  I use Labview 8.5.1 with hardware drivers of 2009-10 with Windows XP SP3.

  Is this something you've heard before?

  Best regards
  Mattias

  Mattias salvation,

  Your task is also reading the CYC on the unit once for example, if you are done reading of two channels.  Reading of the CCM (it's the .../_cjtemp in the error message) is required to return a value of temperature measured from a thermocouple.

  Kind regards

  Kyle

• WLS-9163 is unable to reconnect in wireless mode after reboot in a WLAN with broadcasting SSID

  Initial configuration is defined by MAX using cable.  Wireless configuration is DHCP, with Infrastructure, WPA - PSK.  I save the settings and unplug the wired connection.  Then I delete the original instrument from the list of devices OR DAQmx of MAX.  Then I do a 'find network DAQmx Devices'.  The wireless device is discovered and works (self-test passes).  WLS link on the device indicator is green.

  Then, if I cycle power on the 9163, the WLS link never comes.

  This seems to be because my thread is not broadcasting an SSID.  If I go to a nearby access point and turn on the SSID broadcast, the WLS Link LED lights and MAX can review system.

  Is there a way to make the 9163 connect to a WLAN that don't broadcast a SSID?

  Burned - salvation

  First of all, thank you for the detailed notes. This helps a lot. You have the right version of DAQmx; now, we just need to upgrade the firmware. Here's how:

  After you have added the device in MAX (preferably on an Ethernet connection), click the button "Update Firmware":

  

  You will get a window that looks like this, where you can see what version of firmware you have. Click the folder to find the new firmware. It takes by default in a directory on your hard drive that contains the file 'ni9163fwROM.cfg' (if that's not listed for some reason, you can find it here: C:\Program Files\National Instruments\NI-DAQ\fpgafiles\mionetwork\ni9163)

  

  After the start of the update, you will look at a window of the scrollbar for a minute or two. Then, the device will be auotmatically reboot. You may need to reconfigure your settings after the update.

  Regarding the deletion/time that you did. You should not. After you have configured the wireless, you should see an IP address in MAX on the wireless tab. If she is not there, click "Refresh" now you can pull the Ethernet cable and continue to use the device. (If you want to convince yourself, click on the "Refresh" button again and you will see that the "Link Status" for the "Wired" connection is "down".)

  I hope this helps. Let us know what happens. Thank you

• Configuted auto signed certicate WLS 10.3, but did not work at all :(

  Hello

  I tried to configure the certificate self-signed in my WLS 10.3 and get SSL to work.

  I used keytool as mentioned an article configuration self signed certificate on weblogic server. Avalanche of Tech

  and used the rest that he has proposed. When Weblogic starts there was certain information such as

  "Cannot load a jks keystore comes from the C:\dev\Oracle\Middleware\user_projects\domains\opkk\certs\identity.jks file. "Exception: java.io.IOException: keystore was tampered with, or password is incorrect" and start/stop at the wall. I think the article is well written, but it was missing some information.

  Now I'm situation that I can't get my weblogic upward because of these keytool SSL settings. Are there ways to Weblogic raise when there a mistake?

  What to do now?

  How can I force Weblogic boot dispate ofl errors as Windows used to do and how to get rid of these and correct certificates SSL and/or the keystore settings.

  For your assistance,

  Thank you

  Henkilo fd9fbb10-716f-4fc8-aebc-8a01d7d3e7f3 muokkasi viestia

  This means that the password for such identity.jks as configured in this store is different from what you enter in the weblogic console when you configured.

  Try to update the password for the keystore for identity.jks so that it matches what you specified when you set up in the weblogic console.

  If you can not do this, then you will need to return to a previous configuration. Restore a backup of the file config.xml

• Cannot print on the label Zebra printer when it is deployed to WLS

  With the help of Jdev 12.1.3 on Windows Pro

  My WebApp needs to print labels on a Zebra label printer. The printer is a Windows printer with the name \\print1\Zebra-2. We tried printing from the Web application deployed to WLS in cluster and does not have any exceptions, but no label not printed. A colleague suggested the running on WLS integrated application and see if the symptoms has changed. It was a good idea as the label printed the first time that we have tried.

  Question is, why? Is there some configuration item that grouped WLS needs? Tried some searching on google but no luck at the moment.

  The name of the printer is stored in a database table and appears as installed on the server, but it does not appear on the local computer either so I excluded as a printer driver problem.

  The app is secure ADF when it is deployed. I tested when he worked in the library of the ADF, isolated from the trusted application.

  Is there some security or devices of WLS which must be open?

  Thanks in advance,

  Dave

  it work under Linux:

  	AttributeSet aset = new HashAttributeSet();
  	ASET. Add (new PrinterName (name, null));
  	PrintService [] printers = PrintServiceLookup.lookupPrintServices (null, aset);
  	DocPrintJob job printers [0] = .createPrintJob ();
  	Flavor DocFlavor is DocFlavor.BYTE_ARRAY. AUTOMATIC DETECTION;
  	Byte [] labelarray = labeltext.getBytes ();
  	Doc doc = new SimpleDoc (labelarray, flavor, null);
  	Job.Print (doc, null);

• Deploy the ADF 12 c integrated WLS app can't find class CoreTable

  I use Jdeveloper 12.1.3 on Windows 7 Pro

  Clean my compiled app but when I try to deploy it in the built-in WLS I get this error:

  weblogic.application.ModuleException: java.lang.ClassNotFoundException: org.apache.myfaces.trinidad.component.core.data.CoreTable

  Here is the stack trace:

  < 16 December 2015 15:00:02 EST > < error > < hats > < BEA-149265 > < error has occurred in the execution of the request of deployment with the ID '1742387059852796' for task '8 '. Error is: ' weblogic.application.ModuleException: java.lang.ClassNotFoundException: org.apache.myfaces.trinidad.component.core.data.CoreTable ".

  weblogic.application.ModuleException: java.lang.ClassNotFoundException: org.apache.myfaces.trinidad.component.core.data.CoreTable

  at weblogic.application.internal.ExtensibleModuleWrapper.prepare(ExtensibleModuleWrapper.java:114)

  at weblogic.application.internal.flow.ModuleListenerInvoker.prepare(ModuleListenerInvoker.java:100)

  to weblogic.application.internal.flow.ModuleStateDriver$ 1.next(ModuleStateDriver.java:175)

  to weblogic.application.internal.flow.ModuleStateDriver$ 1.next(ModuleStateDriver.java:170)

  to weblogic.application.utils.StateMachineDriver$ ParallelChange.run (StateMachineDriver.java:80)

  Truncated. check the log file full stacktrace

  Caused by: java.lang.ClassNotFoundException: org.apache.myfaces.trinidad.component.core.data.CoreTable

  at weblogic.utils.classloaders.GenericClassLoader.findLocalClass(GenericClassLoader.java:357)

  at weblogic.utils.classloaders.GenericClassLoader.findClass(GenericClassLoader.java:318)

  at weblogic.utils.classloaders.ChangeAwareClassLoader.findClass(ChangeAwareClassLoader.java:80)

  at java.lang.ClassLoader.loadClass(ClassLoader.java:425)

  at java.lang.ClassLoader.loadClass(ClassLoader.java:358)

  Truncated. check the log file full stacktrace

  I have much deploy other applications on the WLS even without this error.

  Anyone seen this before?

  Any suggestions on troubleshooting is greatly appreciated.

  Thank you

  Dave

  Check and compare libraries of the project against the projects running.

  You should see a difference. I guess that there is either a former library included, or is missing.

  Timo

• WLS 11 g - error BEA-101019

  Hello

  Recently with this exption in one of the ports of WLS 11 g. Clues? Thanks in advance

  [[ServletContext@69507598[app:Weblogic_PD900_3 module: jde path: / jde spec-version: null]] Servlet failed with weblogic.utils.NestedRuntimeException IOException: impossible to analyse the parameters of PUBLICATION of the application: ' / jde/E1VirtualClient.mafService ' to weblogic.servlet.internal.ServletRequestImpl$ RequestParameters.mergePostParams (ServletRequestImpl.java:2144) to weblogic.servlet.internal.ServletRequestImpl$ RequestParameters.parseQueryParams (ServletRequestImpl.java:2024) to weblogic.servlet.internal.ServletRequestImpl$ RequestParameters.getQueryParams (ServletRequestImpl.java:1918) to weblogic.servlet.internal.ServletRequestImpl$ RequestParameters.getParameterNames (ServletRequestImpl.java:1953) to weblogic.servlet.internal.ServletRequestImpl$ RequestParameters.access$ 900 (ServletRequestImpl.java:1817) at weblogic.servlet.internal.ServletRequestImpl.getParameterNames(ServletRequestImpl.java:808) at weblogic.servlet.internal.ServletRequestImpl.getParameterMap(ServletRequestImpl.java:863) at com.jdedwards.base.JDEFilter.doFilter (unknown Source) at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56) at com.jdedwards.util.filters.GZIPFilter.doFilter (unknown Source) at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56) at weblogic.servlet.internal.WebAppServletContext$ (WebAppServletContext.java:3715) ServletInvocationAction.wrapRun to weblogic.servlet.internal.WebAppServletContext$ (WebAppServletContext.java:3681) ServletInvocationAction.run to weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:321) to weblogic.security.service.SecurityManager.runAs(SecurityManager.java:120) to due to weblogic.servlet.internal.WebAppServletContext.securedExecute(WebAppServletContext.java:2277) to weblogic.servlet.internal.WebAppServletContext.execute(WebAppServletContext.java:2183) to weblogic.servlet.internal.ServletRequestImpl.run(ServletRequestImpl.java:1454) to weblogic.work.ExecuteThread.execute(ExecuteThread.java:209) to weblogic.work.ExecuteThread.run(ExecuteThread.java:178): java.net.SocketTimeoutException: Read timed out at jrockit.net.SocketNativeIO.readBytesPinned (Native Method) at jrockit.net.SocketNativeIO.socketRead(SocketNativeIO.java:46) at java.net.SocketInputStream.read(SocketInputStream.java:130) at weblogic.servlet.internal.PostInputStream.read(PostInputStream.java:177) at weblogic.servlet.internal.ServletInputStreamImpl.read(ServletInputStreamImpl.java:229) at weblogic.servlet.internal.ServletRequestImpl$ RequestParameters.getParameterNames at weblogic.servlet.internal.ServletRequestImpl.getParameterMap(ServletRequestImpl.java:863) at com.jdedwards.base.JDEFilter.doFilter (unknown Source) at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:57) at com.jdedwards.util.filters.GZIPFilter.doFilter (unknown Source) at weblogic.servlet.internal.WebAppServletContext (ServletRequestImpl.java:1953) $(WebAppServletContext.java:3681) ServletInvocationAction.run to weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:321) to weblogic.servlet.internal.WebAppServletContext.execute(WebAppServletContext.java:2183) to weblogic.servlet.internal.ServletRequestImpl.run(ServletRequestImpl.java:1454) to weblogic.work.ExecuteThread.run) ExecuteThread.java:178

  Generally happens when a socket connection is disconnected, or when it is reset by the normal application operations.

  You can try to increase the timeout message to see improvements.

  Sign in to the administration Console and the

  Click on the configuration server on

  --> Http and Protocol to define the "Post Timeout" (bones of the default value of 30 seconds)

• 401 error after you deploy for stand-alone WLS

  I use JDev 12.1.3 on Windows 7 Pro

  My app has been migrated to 10g, 11 g to 12 c. He had a guarantee of manufacture which has been replaced by ADF security.

  I have it on my integrated WLS but after deployment to standalone WLS I get 401 - error not allowed after connection through OAM.

  I checked the server logs and don't see any error. The sys admin looks at some other newspapers but nothing concrete yet.

  The app has 26 roles of the company and my login has 5 assigned roles. Some business roles have been defined as Active Directory groups. I tried to check if the roles are case sensitive, but who has not found in textbooks again. Ad groups do not match the case of the roles defined in jazn-"Data.xml".

  Any suggestions on what and where to look is greatly appreciated.

  One suggestion is to remove all business roles and try to make it work with a single role. I intend to try this.

  Thanks in advance!

  Dave

  We found that the question. Business roles are case-sensitive. Windows administrator define groups of ads as of breaks. Jazn-"Data.xml", I made the business roles are all uppercase. Evolution of business roles jazn-data to match fixed the issue ad groups.

• Using the lens of departure-WLS server to start the managed server

  It is possible to start the managed server using start-server using maven plugin WLS goal?

  Documentation indicates the default value that is an administrator of the server. I tried with the next block in the pom file, but it does not recognize the command given here.

  implementation of <>

  < id > start-osb / < ID >

  pre-integration-test < phase > < / phase >

  < objectives >

  < target > start-server < / target >

  < / objectives >

  < configuration >

  < domainHome > givenpath < / domainHome >

  < command >

  osb_server1 startManagedWeblogic.cmd < param > < / param >

  < / order >

  < / configuration >

  < / run >

  Thank you

  Siva

  Hi Robert,.

  When I try to use the pom file, I get the following error. For this reason, I used the command syntax and parameters as displayed above. Even after this change, it does not start the managed server.

  [org.codehaus.plexus.component.configurator.ComponentConfigurationException: cannot assign configuration 'command' with the value entry ' ${domainHome}\bin\startManagedWeblogic.cmd osb_server1 ${adminUrl} "type java.lang.String to property of type java.lang.String]

• Installation of MV 12 c ready for WLS 12 c &amp; Java 1.8?

  Hello

  I want to install the current Version of MapViewer (12.1.3) 12 c under Win7 64,

  It is certified for the last credits WLS 12 c and the latest Java JDK from 1.8 or

  does anyone have a brief note TODO?

  Thank you

  Friedhold

  MapViewer Version 12 c (12.1.3) has not been certified with JDK 1.8. You may encounter problems with the console (pages ADF).

  JDK 1.7 will work.

  There are also 12 c with JRF WLS.

  See the installation guide in the doc.

• ADR on weblogic with jdbc pool of wls

  Is there a way how ords.war can use the jdbc pools standard wls?

  Chris

  Hi Christian B,.

  Christian B has written:

  Is there a way how ords.war can use the jdbc pools standard wls?

  I don't think that ADR uses pools jdbc support for Java EE application servers to which it is deployed.

  If you observe well start ADR log, you'll see that it creates connection pools apex (APEX_PUBLIC_USER), apex_al (APEX_LISTENER), apex_rt (APEX_REST_PUBLIC_USER) and apex_pu (ORDS_PUBLIC_USER) according to the settings of JDBC defined in "defaults.xml" of the configuration of the ADR.

  NOTE:

  • Users of the database are specified in the media for which the JDBC connection pool is created.
  • Pools of connections will vary on which users you set up during installation of ADR.

  See the parameters of connection pool for JDBC:

  • Kris blog: installation jdbc/security auditor Apex
  • ORA-00001: Unique constraint violated: installing Oracle XE, ADR and Apex on CentOS - part 4: stress test
  • http://docs.Oracle.com/CD/E56351_01/doc.30/e56293/Config_file.htm#BABHAJDE

  Why do you want to ADR to use the 'Standard Web Logic Server JDBC Pools'?

  Kind regards

  Kiran

• Strange behavior on WLS in autonomous, and not on WLS integrated

  Hi all

  This project is in jdev 11.1.1.3.0. The stand-alone server version is 10.3.5.0 and the console/em 11 g.

  When I run the project on integrated WLS, inserting rows behaves as expected. When I deploy on a stand-alone server, the inserted rows suddenly have the default values that appear because it's attributes. The values exactly copy the other already existing lines to the table.

  Anyone experienced something like that or know the possible causes?

  Problem solved. It's the 11.1.1.5 insert with immediate = true bug button. We consider using the fix for this problem or live with immediate = false property.

• How to import AD users in WLS

  Hi all

  I am new to the content Web Center and Weblogic Server. I have a scenario drawn in WLS AD user and try to follow the user in WLS. I tried to use the Active Directory Provider, but I can not administer the user AD of WLS. I think that using the format LDIF is one of the option.

  
  

  My question is, h ow can I import AD user and export to WLS using the LDIF script? So, how can I assign the user directly to the existing group to the WCC, and then assign the group with roles? Can I add multiple users to the Group 1?

  
  

  Understand who can help you.
  

  Hello

  By the importation of WLS, do you mean that you import into the authenticator 1 - by default... or 2 provider - in provider AD... ?

  If (1), then you might use a ldif file and import it via console > Security Realms > myRealm > suppliers > DefaultAuthenticator > tab Migration > Import tab

  If (2), then why not import the ldif file directly to the ad itself... ? .. I think it's better, and I don't think that you can import the ldif via the WLS console without affecting other providers in the area of security, under the Migration tab found outside the DefaultAuthenticator in the areas of security > myRealm > suppliers > Migration > import stipulates that:

  "Importing data into the database of the security provider of each security provider configured in the field of security"

  So I would say in this case for import/edit directly on the ad itself...

  For the second question, I think it is better suited to the community of the WCC

  Kind regards

  White