WMP11 preventing streaming?

Similar Questions

• Help! Nothing has worked

  Hi guys, hoping someone out there might have a solution because I tried everything and can not solve a buffer problem preventing streaming on airplay

  was working fine earlier in the evening and just started buffering

  His 2nd gen, wifi is perfect and continuous in an instant on the phone

  I have reset the appletv that normally works, she is set to standard def only and tested 3 devices to ensure that this is the tv and not the phone

  the content is appearing on the screen and buffering without playing (I mean the show is buffered until 5 minutes before the end and it will not play)

  have restarted phone and wifi and tv just in case, and nothing works

  any ideas?

  Thanks in advance for any help and advice

  First, to be clear, when you AirPlay (not mirror) your phone, ATV download flow directly from the internet server.

  Thus, it seems that ATV has a problem with his internet connection. What is the source of the video, iTunes, Netflix, what? Is limited to this source of problem, or it also affects YouTube, Vimeo, etc. ? Using a VPN, RAM or other service to access content outside your area?

• How to use family security to block streaming video photos etc. on Windows Media Player. Or how to prevent users from video straeming

  How to use family security to block streaming video photos etc. on Windows Media Player. Or how to prevent users from video straeming

  Hello

  Please go through this article, change settings for streaming media streaming in Windows Media Player , and you will be able to solve this problem.

• WMP11 stop playing about streaming movies a minute

  Hello

  My friend and I have a problem with WMP11 (Windows Media Player11). WMP stops playing streaming movies a minute with the use of the UC fall almost to ZERO. But he continues to receive data streaming, bandwidth which is 1 MB/s. I have confirmed with the Windows performance monitor.

  My PC has no such problems but PC my friend with Windows XP SP3 and IE8 WMP11. I tried to reproduce the problem. My virtual machine on Microsoft Virtual PC with Windows XP SP3 and IE8 WMP11 could not reproduce. Another virtual machine on VMware Player that has been converted from old machine managed to reproduce the problem. The problem of PC can play movies in streaming, but cannot play other.

  Stop security such as Windows or Symantec firewall software. acceralater changed settings in WMP. But nothing has changed.

  I downloaded and installed the codec pack, but nothing has changed.

  http://www.free-codecs.com/download/K_lite_codec_pack.htm

  Is there anyone who use WMP on vmware player 3.x to play streaming movies? What can I do?

  Thank you.

  ken1tokyo.

  Hello

  You can try to change the buffering settings and check if this helps solve the problem. To change the settings follow the steps below.

  (a) open Windows Media Player

  (b) go to the Tools menu and select Options

  (c) go to the performance tab

  (d) under network buffering select buffer and change the number and check if that helps.

  (e) also try to change the connection speed manually tab connection, on the same page.

  Now, check if that helps.

  Hope this information is useful.

  Amrita M

  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Windows 7; Windows firewall prevents the discovery network, files and printers, sharing, public folder sharing and streaming media

  Windows Home Premium SP1, completely up to date.  Windows Firewall is enabled.

  Try to keep the file sharing and printers on a home network.  Try changing the settings on the control panel; All Control Panel items: Center network and sharing; Advanced sharing settings.

  When I try to change the option buttons for sharing, then click on save changes at the bottom of the page, the screen jumps to the network and sharing Center.  Object entering the settings advanced, no parameters have been recorded.   The comoputer restarting does not help.  I checked that the following services are running and set to automatic according to the http://answers.microsoft.com/en-us/windows/forum/windows_7-networking/cant-turn-on-network-discovery-and-media-streaming/98654e71-4bff-4dd3-acec-ffc3524d44a4;

  The base filtering engine
  DNS client
  Function Discovery Provider Host
  Function Discovery Resource Publication
  HomeGroup listener
  HomeGroup provider
  Server
  SSDP Discovery
  UPnP device host
  Windows Firewall

  When I stop the Windows Firewall service, I can activate the sharing I want.  Of course the windows firewall prevents sharing I would do on my network.

  I'm uncomfortable with Miss having a firewall work on my computer.  How to configure my Win 7 machine windows firewall to allow communications with my homegroup?  I tried to restore the default values.  This did not allow the communication.  I tried to find the homegroup settings in the advanced settings of the windows firewall.  No luck there.

  What should I do to configure my windows firewall to allow network discovery and file sharing of printers and media streaming and sharing?

  Hi stephanie,.

  Thanks for joining us out on Microsoft Community Forums.

  Looks like the Windows firewall prevents the discovery network, files and printers, sharing, public sharing of files and streaming media. We will analyze and identify the cause of the problem.

  You have a third-party antivirus installed on the computer program?

  Method 1:

  To turn on network discovery
  
  1. Open advanced sharing settings by clicking the Start button, then Control Panel. In the search box, type network, click Network and sharing Center, and then, in the left pane, click on change settings for sharing advanced.
  2. click on the chevron to expand the current network profile.
  3. click turn on network discovery and then click on save changes. If you are prompted for an administrator password or a confirmation, type the password or provide
  confirmation.

  The article below explains all about the network discovery:
  http://Windows.Microsoft.com/en-us/Windows7/enable-or-disable-network-discovery

  If any of these responses not solve the issue, let us then run the sfc scan and check if any file system is corrupt. I also recommend to perform a clean boot in order to find the root cause of the problem.

  Method 2:

  Use the (SFC.exe) System File Checker tool to determine which file is causing the problem and then replace the file. To do this, follow these steps:

  a. open an elevated command prompt. To do this, click Start, click programs, accessories principally made, right-click Guest, and then click Run as administrator. If you are prompted for an administrator password or a confirmation, type the password, or click on allow.

  b. type the following command and press ENTER:
  sfc/scannow

  The sfc/scannow command. analyzes all protected system files and replaces incorrect versions with appropriate Microsoft versions.

  More information on SFC scan found in this document:
  http://support.Microsoft.com/kb/929833

  See also:

  Open a port in Windows Firewall

  http://Windows.Microsoft.com/en-in/Windows7/open-a-port-in-Windows-Firewall

  Allow a program to communicate through Windows Firewall

  http://Windows.Microsoft.com/en-in/Windows7/allow-a-program-to-communicate-through-Windows-Firewall

  Hope this information helps. Get back to us if you have more queries about Windows.

• Podcasts, backup a podcaster can take to prevent implementing streaming links?

  Hi all

  A podcast that I listen to the guard to give me streaming links instead of the actual podcast. The podcast is all things Radio, and in the description of podcast, they like to put links to streams of radio stations that they appear in the podcast description. I'm fine with that, except that sometimes, when the podcast is pushed to my phone, what it is is a link to the stream of the station. Is that all I can tell them to do to make sure that, when it is pushed to the iTunes store, that the correct link to the podcast is used to supply 100% of the time? It gets really annoying to have to go on the site when I should just be able to get on the phone.

  Not sure that this would technically be a device se - problem your best bet would be to contact the company that makes the podcast available at the iTunes store and talk with them

• In swf streaming in when preloaded prevents?

  So! Here is y at - there no way to stop a load in .swf of streaming, using the charger, other than to have a stop on the first empty keyframe action of the load in the movie itself?
  
  I always get the video to not show up, but what about the sound? How can I keep it is heard, streaming, during the preloading process?
  
  Thanks in advance.

  Too bad! Problem solved!

  My last question above got me thinking and I found a solution!

• Jump in the middle of an audio track streaming on various sites causes the stuttering and audio glitch

  Hello

  Please refer to this thread for support on the technical support of SoundCloud forums. The thread contains all relevant information, including videos of the screenshots problem and console, made by myself and others. https://www.soundcloudcommunity.com/SoundCloud/topics/skipping-to-the-middle-of-a-track-causes-stuttering-and-glitchy-audio-chrome-Firefox

  In short, when you try to move forward for streaming audio, there is a memory buffer/stuttering problem that prevents a correct reading of the track. This problem is confirmed on SoundCloud and Traxsource and other people in the support thread mentioned Mixcloud and other streaming sites. In other words, it is not the special streaming service fault or another.

  The problem does not occur in Microsoft Edge, Internet Explorer or Chrome. Well, to clarify, when the issue was published on SoundCloud support forums, Chrome was having the same problem. However, they made a version a few days ago thrust, that fixed it.

  Here's my original on the SoundCloud support post (less), which has the relevant details. Note that we have updated both Flash and Firefox recently, so although I have mentioned earlier in my original post, everyone involved has since updated their browsers and Flash.

  From now on, the only solution for the problem is to go back to Firefox 40.0.2. Thanks for any help =)

  Matt

  Original message =.

  Jump in the middle of a track causes the stuttering and audio glitch (Firefox).

  I am running Windows 10 Pro.

  There seems to be a problem of caching that affect reading - I started noticing this problem three or four days ago. Previously, I could jump through my feeds at will, go straight until the middle of the tracks or mixes of listen seconds and determine if I liked the track. Now, I can't do it on Firefox 41.0.1. The problem is simply annoying on songs that are 3 or 4 minutes in length, as I must leave "cache" maybe ten seconds before jumping. Unfortunately, the problem is a game-breaker on mixtures which, for example, are 90 minutes long. If I jump to a point directly in the middle of the combination, nothing happens. The play button alternates between the 'Play' symbol and the symbol of 'Caching' ('... "), and so audio resumes, it is glitchy and consists of different parts of the track being played at the same time.

  I've eliminated my internet connection as the source of the problem by loading on board. On the edge of 20.10240.16384, the problem does not exist. I can scroll down to any mix of 2 hours in my stream, click on the middle of it, and the audio starts right up. No caching, without stuttering or glitching.

  I drove back Flash version 18 to see if it solved the problem in Firefox, but it did not. The problem persisted, so I re-updated to Flash 19.

  Yes, I understand how all versions and updates to work. I meant it as a generation of powder magazine. My bad.

  I consider this problem to be solved. Several different pre-release versions of Firefox have solved the problem; I have personally used both of them that work perfectly. A representative of Bugzilla stated that the patch will be integrated into Firefox 42, which will be released on 3 November.

  https://www.soundcloudcommunity.com/SoundCloud/topics/skipping-to-the-middle-of-a-track-causes-stuttering-and-glitchy-audio-chrome-Firefox?topic-reply-list [Settings] [filter_by] = all & question-answer-list [parameters] [reply_id] = 16269116 #reply_16269116

  I now consider this private matter. Thanks to all of you who have been here =)

• USBOTG and Charge at the same time on Stream 8

  To keep this thread as productive as possible and efficient for those who find it useful to:

  Unless you have under your eyes

  1. a schematic representation of the 8 Stream USB port (USB port and battery electric circuit etc.)

  2 source code for the firmware BIOS and kernel that controls the material

  Please DO NOT respond or say "is not possible".  In view of the above is true, you do not have enough information to say '' not possible. ''

  If no one replys with a solution, what he calls not possible by default.

  Also please do not answer to say ' I don't know how "or" but I know how to do anything else that ' is also not that useful.

  An update of the BIOS or other software update may be required by HP, Microsoft or both to offer this feature really intuitive and quite possible.

  And I hope that this thread can be an effort consolidated by all who have the 8 flow to make the necessary changes.  The majority of the other tablet PCs are capable of it.  It seems that only the 8 Stream and a few others have trouble with her.

  ~~~~

  I want the ability to use a simple, inexpensive cable and perhaps standard (with electronic active minimum inside) which allows me to host and to use one or more USB devices on the Stream via its USB port B microphone 8 while this cable can also be connected to a charger standard and charge 8 flow simultaneously.  This means that the cable has a minimum of three connectors.  One of the possible configurations are as follows (apart from the normal charging cable):

  1 cable Micro USB B Male - connect to the stream 8

  2 USB male A - connect to the AC charger (IE one that came with the 8 Stream)

  3. USB A female - one or several connectors to plug into the key of USB data, keyboard, mouse or even a hub.

  Connector # 2. above shall provide a power supply to recharge the 8 Stream via conn. #1 and the power supply for external USB devices via conn. #3 so that they are in use - all at the same time.

  A and if the same cable can act as a normal OTG no charger for when no external power supply is available.  This may necessitate a switch or an electrontics active inside.

  The last part of this goal is unimportant for various reasons.  I wish that HP, the manufacturer of 8 flow, to State in writing good mode necessary to do this, so that other manufacturers or even-it yourself can make maximum use of their tablet HP equipment.

  ~~~~

  The neat thing it will alow a person to do with their tablet, it is to work at home using the Tablet as a desktop PC by connecting a keyboard, mouse, perhaps external screen (with USB to the display adapter) and knit for a long time without time limit prescribed by the battery life because the charger provides energy to all involved.

  If there is only a single connector on the cable #3, then an additional node of coarse had to provide support for these multiple USB devices at the same time.  However, it would be better if there were several #3 connectors integrated in the cable itself.  This would be better as a suitable USB hub also requires its own power.  That an adapter is necessary if the whole thing were integrated into one.

  ~~~~

  I really want answers from anyone who has already accomplished USB OTG delivered with simultaneous load with flow 8. (independent of any published 'proper' way is also welcome)

  Today's date is 2015-01-16.  If in 2015-02-16 (one month), nobody has posted a solution and then starts to bug HP and Microsoft on it's us?

  ~~~~

  Technical training:

  I understand the possibility the tablet software and firmware must take a decision on the manner in which power flows on the power port USB microphone B pins.

  I know that with a proper design of the electronic circuit carring these signals of power inside the Tablet could be sensitive to what is connected and without risk to decide for himself what to do without needing to control software.  For example by testing/detecting periodically differential voltage or current management to see what sides of the connector can supply.

  But this is only one of the many "could bes".

  In addition, this can be no standard regarding the standard USB.  What seems to be actually the case with a lot of cables OTG + fresh, is that physical clues embedded in the cable or charger are used to signal to the Tablet what the situation is.  Then the signal of software/firmware of the Tablet, interprets what the situation is intelligently and responds by flipping the bits of correct hardware control to activate, or deactivate the power flow in the port and also control its direction in or out.

  I'm not familiar with the standard USB.  Maybe I could do more research, if I believed that HP followed with 8 Stream or even the standard covered this situation explicitly.

  But to a certain extent, it seems I'll have to invent something that should be intuitively just like it does with other tablets. Isn't it?  Maybe I'm overthinking, but I can't find any USB OTG + cables load that specify compatibility with 8 HP flow.

  In any case, I was familiar with both methods other use of tablets to send the highest mentioned signal to the hardware/firmware/software of the tablet to the idea that it's time to load / time of OTG or both.

  The first method is a 0 Ohm to 200 ohms short between pin USB A 2 and 3.  This is the bidirectional data differential lines D - and D + respectively.  In data mode, all the data passes back and forth on those lines.  When you load with a cable, it's the charger module that puts this short, not on the cable.  I measured the short on three different Chargers.  It is 0 Ohms on two of them, one of those who are the charger that came with the 8 HP flow.  The others 0 ohms was generic.  The third was for an apple iPad and it measured on 53KOhms.  It's probably not the resistance ohms 0-200, but probably it is impedance termination indicating that there is some intelligent serial port communication in the charger itself.  Leave it to Apple to be different.

  This method is somewhat questionable, as this signaling mode would prevent OTG + fee because it seems unlikely that you will be able to OTG when the data lines are shorted each and overloaded with such low impedance.  I could be wrong on this subject...

  The other method I have seen suggested to work with some tablets and phones other than the 8 stream is too short the USB microphone B pin 5 to Terminal 4 with 0 Ohms to 100 000 Ohms.

  USB B has 5 pins.  USB has only 4.  The extra pin on B moves the GND pin 4 pin 5 pin to and makes pin 4 PIN ID.

  If this signal applies to a drop in the ID pin (4) or in some cases, I saw that she proposed, he runs down with 0 Ohms.

  Dead shorting things always makes me nervous.  If ID is a simple normally high impedance high input, resistance could be used to make voltage well below the low or zero threshold while also preventing the risk of damage when cheat on him with a device that you do not have the diagram for.

  Yet, 100K is a bit high for a 'pull down' in most of the situations that I'm used to.  Even a 10K would be uncertain. A 1 K or 2 K seems reliable enough, but then things are weaker and in know more nowadays low...   All but a dead short but if possible.

  So, it seems possible that the device might be able to "indicate" by the specific value of the resistance, which can be found here.  In other words the resistance is not a pull down but in fact a signature analog ID, in which case the exact value will be crucial. So if this is the case, a guess is not going to work.

  Obviously in such a system as described above, a chip inside the Stream 8 should be responsible to support this information. I hope the 8 Stream has such a chip.

  Probably a register inside this chip would be at all times what the State of the pin ID is a binary number.  All that is needed is for the BIOS to the chip and the registry in it and read this number via the bus to determine what happens to the port. Finally, he would use that signals of info to send the order of material to the electrontics of power set the appropriate direction to take etc.  (and change the State of the icon on the screen of the rude)

  I don't know if the PIN ID method described is a standard USB or not either.

  Eventually, there may be a third way. But I do not suspect that it would be possible with a non-active external device. In any case too complicated for the novice DIY for sure.

  The device would need to act is a kind of extension of bus.  As an active hub.  But she would use the negotiation of data USB serial lines and in addition to reproduce one or more additional USB ports, intelligently inform the tablet to get with the program which is "now we're going to otg and recharge at the same time."

  This requires a smart external device with a processor Inside, no doubt.

  It seems to me that many other tablets have been able achieve avecjoint here the need for a smart external device and thus the flow must also be able to do.

  There is a device that claims to be able to work with the HP Jet 7 and 8 and provides same ethernet and USB and big DVI ports so loads the data stream.  But its expensive because it is active.  Se here:

  http://AMZN.com/B00OVDE0GC

  It's called a "Docking Station".

  A reference to a product that does exactly what I want (possibly without active electronic components) is here:

  http://AMZN.com/B00LTHBCNM

  It's by Kirin and it is a device of type squid with four USB ports.  Precisely, which is my goal.  But read in the comments stream 7 user indicated that he would not be OTG and load, not really clear if it worked as a hub USB OTG or not.  Another evaluator stated that she would not support even a single USB device much less fees of 8 Stream.  This device has a switch.

  I forgot to mention that some 'hackers' have claimed success with other tablets to deceive their devices by using a multi-step process to plug things in.  Usually in general they would get connected Tablet and load first, then they would return a switch or something remove some resistance or the signal was introduced by the first position of the switch. For some reason any Tablet would continue to require. Then the data lines would be free and they would plug in a usb key and it mounts correctly even if the tablet was always in charge.

  It's like the power circuit has a lock which does not allow it to return to the mode "power flow" as long as he still feels the power flows inward regardless of what software it is telling.  Full proposal here.

  These tips seem dubious to me.  Changes in the BIOS could change the way it works.  Also you can not be sure what actually happens if you do not have a schematic representation.  You could damage your tablet.  Many people will support icon in the operating system whether the Tablet is in charge.  But I'm sort of a low-risk guy and my policy is generally indicators of intereperet not to have meaning at all once a device is functioning in a non-standard setting.  Especially when it's something that I did not built and could not fix if I FRY.

  Hypothetical reasoning: tell me what data sensory discs really the State of the charging light screen?  This reflect the bit of hardware control programs actually feeding management and status on the port?  Or does it measure the direction of the flow of power, said in the section of the circuit battery monitoring?  Point - none of us have a schema because it's owner. To really be sure according to the smart electronic hardware, the port must be mode flow under advisement "of power. If it's in a "power flow out" mode and power will be delivered externally as well you wind upward with both power supplies the same power at the wheel nets.  In this case, the two opposing regulators attempting both to drive 5 V can have slightly different voltage calibrations.  That could lead to fighting between them, with more than 100% of their capacity.  For example if you try to regulate 4.95 real V and the other and other attempts to regulate 5.05 V.  Current then flows to the tune of 100 mV / a few milliohms in the cables linking the two.  This may be several amperes. (many)  In other words, like I said: you want the tablet to know that power is coming in don't go out and automatically hitting the internal switches needed for that to happen. Probably the icon should indicate this with precision, but in some wacky situation, he could not. There may be a chance that the icon could indicate the load and still be burning or focusing on some circuits of the tablet or the charger.

  Another thing, I could see that happening is if you play with these reported resistance types enough you might find a resistance value that winds up place the device in an intermittent condition.  In other words it keeps flipping back and forth quickly between OTG and fresh.  It can give the illusion that it works.  You can have marginal communication with your USB devices and battery could even load.  But will still be a lot of stress on the power circuit.

  It is difficult for me to risk a Tablet perfectly well if I don't know exactly what I'm doing.

  If a brave individual makes their own experimentation and verifies that it charges and OTGs and you tell the rest of us, you're a hero.

  Maybe one of you has a good knowledge on the USB standard to have more confidence in such an experience... like what the ID pin 4 REALLY supposed to work for example?

  That's what I know so far.  If you think you can help, thanks in advance, or if this helped you, then your quite welcome.

  It works

  http://Accessories.us.Dell.com/SNA/ProductDetail.aspx?c=us & l = to & CS = 19 & SKU = 470-abes & baynote_bnrank = 0 & baynote_irrank = 0 & ~ CK = baynoteSearch & dgc = CJ & cid = 47997 & lid = 4279734 & acd = 10550055-4485850-eb75dcb47e53437680ed323a1f4885fe

  Evidence

  http://targusblog.com/2014/11/25/how-to-turn-a-99-Tablet-into-a-workstation/

  But it's 4 x the price in Europe

  Have fun

• Family sharing prevents Sync music?

  I just started the sharing of family and I can are no longer synchronized songs (not downloaded via iTunes) to my iMac to my iPhone.  The best recommendation I found on Apple's site has been to use home sharing. HomeShare provide a real sync on my phone (actually transfer music on my phone), or just provide a service of streaming from my Mac to my iPhone?    I listen to music in my car a lot, and I don't want to be constantly with the cell towers to listen to music from my Mac at home...  Would help to all points of view.

  I download music at Amazon and rip my personal library of CD in addition to using iTunes.  I am trying to find a way to get the music on my iPhone to my iMac.

  Home sharing is for playback of content in a different iTunes library that is located on the same local network.  It is not for synchronization or transfer of multimedia files.

  Family sharing should not prevent the synchronization of your own media.  Please provide more details...  What happens when you try to synchronize?  What keeps you in sync?  You get an error message?  If you do what he says?

  Do you usually use the parameter manually manage to load songs on the iPhone (drag and drop the songs on iPhone in iTunes)?  Or do you use the Sync music setting so that iTunes automatically sync your library iTunes music (or a selected part of it) for your iPhone?

• Stream 8 T-Mobile activation failure

  I bought a Tablet HP flow 8 (model number 5901) three days ago and I have not always been able to set up the free monthly 200 MB of data from T-Mobile that is supposed to come with her.

  As indicated in the instructions of the Tablet, I turn off Wi - Fi, turn on Mobile broadband and to connect to T-Mobile. Internet Explorer opens to https://mim.t-mobile.com/primary/openPage. I then click the button to connect. After a few seconds, I find myself https://mim.t-mobile.com/jsp/ServiceUnavailable.jsp. This page tells me, "we're sorry...". We were able to respond to your request. Please go back and try again. "Try again simply generates the same message.

  Page also told me to call 1-800-937-8997 and T-Mobile will be 'happy to help '. I tried, and a bunch of confused T-Mobile Indian reps simply transferred me back between support and activation of tech services. So, I called HP and they just transferred me to T-Mobile (which is what I expected).

  Everyone knows about this problem? This may mean that the T-Mobile SIM card that came in my tablet is defective? Or does this mean that T-Mobile Connect Me site has been down for the past three days? It would mean that the intensity of the signal from the T-Mobile network is too low? I have three of the five bars at the moment when it is connected to the Broadband Mobile, which shows me connected to T-Mobile via HSPA +. All I know is that I get quite irritated by all this.

  Visitors to Stream 8 HP:

  The temporary problem that prevents activation of devices HP flow 8 on mobile internet service T-Mobile has been resolved.

  If you have not activated the data free of charge for the promotion of life on your device, please follow the activation instructions provide in the box, or go to www.hp.com/go/freemobility for a step-by-step activation guide.

  Once again, we apologize for the inconvenience and sincerely appreciate your patience.

  HP mobility team

  T-Mobile customer

• How can I prevent my itouch 32G to appear on my Iphone6 child photos? If I give him his own apple ID then she loses all his music already purchased.

  How can I prevent pictures of my itouch 32G to appear on my ios Iphone6 9.2 child? If I give him his own apple ID then she loses all his music already purchased.

  Is his pictures are showing on your phone, then that implies that she (and you) use the same account iCloud on your devices and are both using photo stream. She could use have and use his account for the parameters > iCloud or that she could not use Photo Stream (settings > Photos & camera on the device)

  Or you can configure the family sharing (if she is under 13 years old you need a credit card to create an account due to the child online protection Act), she should still be able to share purchases that you have made on your account, but future purchases, she would be linked to his account

  Family sharing: http://www.apple.com/icloud/family-sharing/

  Child accounts: family sharing and Apple ID for your child - Support Apple

  Shareable shopping: What are the types of content can I share with sharing family?-Apple Support

  Family sharing 'request to buy': ask and make purchases with Ask to buy - Apple Support

• How to transcribe audio streams in real-time text?

  Hello

  Currently, I listen to a live audio stream voice using Communicator Desktop WAVE on Windows XP. I want to use a voice-to-text application to transcribe this audio in Word or Excel in real time. I'm looking to reproduce the same experience as the direct subtitles on TV. I read that Windows is a speech recognition software and there are also 3 application of the part such as Dragon NaturallySpeaking. Is it possible to what I can achieve this?

  Thank you very much

  dambk.

  Hello

  The speech recognition software is not transcribe audio voice to text.

   
  You can search in your favorite search engine for the voice to transcribe text software.
  Note: Using third-party software, including hardware drivers can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the use of third-party software can be solved. Software using third party is at your own risk.

  You can also visit these links to learn more:

  http://Windows.Microsoft.com/en-us/Windows7/set-up-speech-recognition

  http://Windows.Microsoft.com/en-us/Windows7/what-can-I-do-with-speech-recognition

• How to download TV programs Italian streaming?

  When I look on the Italian programs streaming on line, they all stop and start and many programs are only available for viewers of the local population. Unless I can download I'll have to put up with this frustration. I live in apartments, I am not allowed to deploy a satellite, foxtel, or other means of payment are simply too expensive for a pension.

  Can you please help with, how to download TV programs Italian streaming?

  Concerning

  Gabriele

  Hello

  Which site do you use to watch videos online?

  Perform the steps from the link below and see if it helps.

  Problems playing the videos by using Internet Explorer

  You use your favorite search engine to look for software that can help you download streaming programs.

  WARNING of THIRD PARTY SOFTWARE: Using third-party software, including hardware drivers can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the use of third-party software can be solved. Software using third party is at your own risk.

  Hope this information helps.

• Connection error (streaming) at Airport Express to iTunes & Airfoil on Windows XP

  I use Windows XP 2002 SP3 on a Dell Latitude E4300 laptop, connect to a router Linksys WRT54G, providing a network home WPA2-Personal (TKIP + AES).

  I see my Airport Express 802.11n in iTunes 10.4.1 and can select it via the Airplay button. But when iTunes tries to connect, it comes up saying ' an error occurred during the connection to the antenna device xxx. ". An unknown error has occurred (error-15000).
  A similar problem happens with wing of Rogue Amoeba that I use to listen to the music of other applications such as VideoLAN to Airport Express. I see that my Airport Express is available but when Airfoil tries to connect, it comes up saying that "it seems that a firewall on this computer prevented Airfoil to connect to Airport Express xxx. Please check your firewall settings and try again. ».
  I put Airplay and iTunes as exception in my Windows Firewall configuration and even added 5000 to 5005 TCP and UDP ports 6000-6005 such exceptions recommended by the wing. I also disabled Symantec Endpoint Protection I installed. The only thing I can not disable is McAfee Endpoint Encryption, since I also use the laptop at work and I don't have permission to disable McAfee.
  How do I followed what happens is to prevent iTunes and wing of streaming to Airport Express Terminal?
  Also, I have a Windows Vista running on another laptop Dell Inspiron computer on the same network and have no problem streaming music from iTunes or the wing at the Airport Express on the same network.
  Thank you

  Hello

  You receive the error message relates to the firewall blocking the connection on Windows XP you can connect using Windows vista computer.

  You will need to disable Mcafee on the computer for which you can contact sysadmin at work in order to allow access to Mcafee and check if it helps.