Similar Questions

• WRT 160N v3 - starts the problem (power problem)

  Hello.

  I recently bought the WRT 160N-ee. The problem is that the router will not start when it is plugged (led starts to blink and the router is humming). It starts only when I plug the power addapter into the first and then connect the 12V DC to the power supply. If I do the opposite (1 connect all the cables to the router), then plug the power addapter it does not start.

  This means that the router does not start after a power failure. You must unplug the power cable and put again to start the router. Has anyone have the same problems? Looks like is it a broken capacitor, doesen't it?

  I sent my back and they replaced with a stronger one 12V DC 1A adapter.

• Config problem and reading of AI

  Hello

  I have a problem when I use have config and read the structure.

  I use Labview new v12.0 and chassis PXI-1042 NI6120 daq card.

  If I use NI MAX, I can measure approximately 1 V (which is the minimum value for the sensor) or I can measure 1 V using the voltmeter.

  (@ OR MAX, I have set up for voltage analog - NI 6120 - ai0 - 0/5V DC - 20 kHz sampling frequency and number of samples of 4 kHz)

  When I use have config and read the structure, I can't measure 1V! Channel ai0 value is 0 a little.

  Config and read the ai0 channel structure is attached.

  You have an idea what the problem is when I use config and read the structure.

  Best regards

  Serdar

  Two thoughts:

  1 looks like to your acquisition is set to finished samples, then you're exciting the sensor before running the code? Or have you tried to change continuously, so you can change the voltage of the sensor the code runs?

  2. you mention DC in your configuration of MAX, but your coupling in your "10045" code means coupling AC. Do you intend to use the current alternative or continuous? If you want DC, your value of coupling must be 10050 (or you need to create a constant off the coast of the entrance so that you get the enum rather than use a digital).

  Hope that helps!

  -Ryan_S

• BEFSR41 v4.2 with AT & T DSL & PPPoE Config - help!

  I'm about to set up my first DSL connection, which will use PPPoE and a Motorola 2210 DSL modem provided by my ISP, AT & T. The DSL modem stores the user ID and the password. After I get the DSL up (which I think I can handle via a manual installation rather than installing the software provided by AT & T), I will install a router BEFSR41 v4.2 for my new home network. The v4 manual says that I also need to enter the ID and password for PPPoE supports as well as a service name. If the modem is to store the password, why do I also need to put them in the router config. ? In addition, the v4 manual says I need to enter a "service name", which I do not think that I know and do not know what it is supposed to look like. I think I can handle the rest of the router config, but will also enjoy a lot of tips or tricks with this particulare configuration. Thank you!

  My DSL and home network are up and works fine. After I discovered that the Motorola 2210 is a gateway and not just a DSL modem, I knew better what I was dealing with. I used the simplest option, which was to implement the BEFSR41 for DHCP and PPPoE about the 2210, changing the router IP address to 192.168.0.1. I discovered that I had to use the AT & T software furnished to completely configure the service - manual install only did part. After that I got DSL service set up, I moved my connection PC Ethernet back to the BEFSR41 and 2210 to the router cable. Worked like a charm!

• ASA 5505 VPN Client Ipsec config problems

  I configured the asa the wizard to Setup vpn, but this still does not work properly. Vpn connect without problem, but I can't access all the resources on the 192.168.1.x subnet. Don't know what I'm missing here, here's a copy of my config.

  ASA Version 8.0 (3)
  !
  host name
  domain name
  activate the password
  names of
  !
  interface Vlan1
  nameif inside
  security-level 100
  192.168.1.3 IP address 255.255.255.0
  !
  interface Vlan2
  nameif outside
  security-level 0
  "Public ip" 255.255.255.0 IP address
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  !
  interface Ethernet0/4
  !
  interface Ethernet0/5
  !
  interface Ethernet0/6
  !
  interface Ethernet0/7
  !
  passwd
  passive FTP mode
  DNS lookup field inside
  DNS domain-lookup outside
  DNS server-group DefaultDNS
  Server name 192.168.1.28
  domain fmrs.org
  GroupVpn_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0
  vpngroup_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0
  outside_access_in list extended access permit tcp any any eq pptp
  outside_access_in list extended access will permit a full
  inside_nat0_outbound list of allowed ip extended access all 192.168.99.0 255.255.255.0
  inside_nat0_outbound list of allowed ip extended access entire 192.168.1.0 255.255.255.0
  inside_access_in to access ip 192.168.1.0 scope list allow 255.255.255.0 any
  access extensive list ip 192.168.99.0 inside_access_in allow 255.255.255.0 any
  inside_access_in list of allowed ip extended access all 192.168.99.0 255.255.255.0
  pager lines 24
  Enable logging
  asdm of logging of information
  Within 1500 MTU
  Outside 1500 MTU
  mask 192.168.99.2 - 192.168.99.100 255.255.255.0 IP local pool GroupPool
  ICMP unreachable rate-limit 1 burst-size 1
  ICMP allow any inside
  ICMP allow all outside
  ASDM image disk0: / asdm - 602.bin
  don't allow no asdm history
  ARP timeout 14400
  Global 1 interface (outside)
  NAT (inside) 0-list of access inside_nat0_outbound
  NAT (inside) 1 192.168.1.0 255.255.255.0
  public static tcp (indoor, outdoor) interface 192.168.1.62 pptp pptp netmask 255.255.255.255
  inside_access_in access to the interface inside group
  Access-group outside_access_in in interface outside
  Route outside 0.0.0.0 0.0.0.0 66.76.199.1 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout, uauth 0:05:00 absolute
  dynamic-access-policy-registration DfltAccessPolicy
  RADIUS protocol AAA-server fmrsdc
  fmrsdc AAA-server 192.168.1.28
  Timeout 5
  fmrsasa key
  Enable http server
  http 192.168.1.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  Dynamic crypto map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
  outside_map interface card crypto outside
  crypto ISAKMP allow inside
  crypto ISAKMP allow outside
  crypto ISAKMP policy 10
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  No encryption isakmp nat-traversal
  No vpn-addr-assign aaa
  No dhcp vpn-addr-assign
  Console timeout 0
  dhcpd outside auto_config
  !

  a basic threat threat detection
  Statistics-list of access threat detection
  GroupVpn internal group policy
  GroupVpn group policy attributes
  value of server WINS 192.168.1.28
  value of server DNS 192.168.1.28
  Protocol-tunnel-VPN IPSec
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list GroupVpn_splitTunnelAcl
  FMRs.org value by default-field
  ID password cisco
  tunnel-group GroupVpn type remote access
  attributes global-tunnel-group GroupVpn
  address pool GroupPool
  authentication-server-group fmrsdc
  Group Policy - by default-GroupVpn
  IPSec-attributes tunnel-group GroupVpn
  pre-shared-key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  inspect the pptp
  inspect the icmp
  !
  global service-policy global_policy
  context of prompt hostname
  Cryptochecksum:b5df903e690566360b38735b6d79e65e
  : end

  Please configure the following:

  ISAKMP nat-traversal crypto

  management-access inside

  You should be able to ping of the SAA within the IP 192.168.1.3

• Several Apex listeners on a single server with apex-config problems. XML

  I use 0C4J to deploy apex on a windows server. I want to be able to have multiple instances operating OC4J pointing to different databases. I read through the documents and messages of the forum and that seems simple enough.
  
  I have an instance running at E:\OC4J and works very well. I added a second OC4J instance at E:\OC4J2. I rebuilt and redeploy the apex.war file after editing the web.xml file to specify a new location for apex - config.Xml. I try to specify the directory config as E:\OC4J2\config but can't seem to get the right syntax, because it keeps picking up the default OC4J instance uses.
  
  < context-param >
  config.dir < param-name > < / param-name >
  E:\oc4j2\config < param-value > < / param-value >
  < / context-param >
  
  I tried several versions of the track E:\oc4j2\config, E:/oc4j2/config / oc4j2/config, \oc4j2\config, but none does not seem to work.
  
  Everyone could not confirm the proper syntax to specify the path to the Summit - config.xml in the Web.XML on a windows server?
  
  Thanks in advance

  Great to hear you found the solution yourself, and share it in any case.
  Please also consider your marker as replied, so others for similar problems will be able to recognize that it could contain a solution to the search.

  Thank you

  Udo

• E2000 wireless PPPOE connection problems.

  I checked my username and password again and again. When I try to connect the router to the internet, I get an error message saying IP not given. How can I fix it?

  slushpuppie371112 wrote:

  I checked my username and password again and again. When I try to connect the router to the internet, I get an error message saying IP not given. How can I fix it?

  Who is your ISP? What is the brand and the brand of modem? You are able to go online through your modem? What IP are you on the computer when it connects directly to the modem? It is possible that your modem doesn't require your router to PPPOE mode. Try to set the router to DHCP Auto Configuration.

• UCS B420 M3 config problem / question

  Hi all

  at this time I had 2 questions requiring my consultation with the community:

  1. I try to get set up on the CCW the sku for UCS B420 M3, but the only part that shows is UCS-B230M2-VCDL1 and does not show any other SKUS for UCS - B series servers, where we cannot set config to get a quote?
  2. In the CET record says that the UCS B420 M3 may had 4 processors, each processor with 8 cores. in this order, you had 32 total cores in the blade?

  The SKU is UCSB-B420-M3-you and for the complete solution, you can also use n20-z0001.

  Yes B420 M3 has 4 processors with 8 cores per processor, so you can have 32 cores in B420 M3

• AUTODECOUVERTS tomcat webapp-config problem

  I run an instance of tomcat 5.5. I copied all of the files required in common/lib for tomcat and webapps dirs and enabled the filter in the Web.XML of my webapp. Then I edited the config at HQ server properties, specifying the url correct jmx and turn on automatic detection.
  
  services that were discovered were a connector and a webapp. None of them appear to be configured correctly, tho. the connector has two entries of the same configuration properties (data are correct in both). the webapp has also two identical config accessories, but does not have the path of the context - we discovered that /webapp, but it should be /cosmo. I tried to change that, but failed with "proceeding not found hyperic - hq:type = Context, name = / cosmo. I have something misconfigure in my Web application?
  
  for reference, the discharge of jmx (http://localhost: 8080/hyperic-hq/jmx-attributes? dmp = hyperic-hq: *) looks like this:
  
  Time: 1149644215276
  Distance: 127.0.0.1
  User: null
  Server: Apache Tomcat/5.5.9
  
  Name: hyperic - hq:type = RuntimeInfo
  TotalMemory: 33357824
  Pages: 14727408
  ActiveThreadCount: 23
  ActiveThreadGroupCount: 3
  
  Name: hyperic - hq:type = ProcessInfo
  MemSize: 890380288
  MemVsize: 890380288
  MemResident: 78622720
  MemShare:-1
  MemPageFaults: 31345
  TimeUser: 17
  TimeSys: 3
  
  Name: hyperic - hq:type = ServerMeasurement
  Availability: 678983
  Available: 1
  ServerInfo: Apache Tomcat/5.5.9
  
  Name: hyperic - hq:type = Context, name = / webapp
  Available: 1
  DocBase: / Users/bcm/work/osaf/cosmo/src/webapp /.
  MaxTime: 0
  RequestCount: 0
  ErrorCount: 0
  BytesReceived: 0
  BytesSent: 0
  NomContexte: /webapp
  MinTime: 0
  TotalTime: 0
  ResponseTimeLogDir: / usr/local/hyperic/logs
  AvgTime: 0
  SessionsCreated: 0
  SessionsDestroyed: 0
  
  Name: hyperic - hq:type = AllContextInfo
  RequestCount: 0
  TotalTime: 0
  
  Post edited by: bcm

  The only configuration item that you need to change is the configuration jmxUrl for the Tomcat 5.5 Server resource parameter.  The configuration for all Autodiscover services should be detected automatically.

  Try to remove your Tomcat server and import it back.  Then configure the jmxUrl for the Tomcat 5.5 Server resource.  Perhaps attempts to change the configuration for services threw out the scheduling of the metrics.

  You can also restart your agent, the log file should never be 0 bytes, unless you have never started it :)

• SQL vCenter Orchestrator config problem

  I recently downloaded and installed vSphere 5. I installed vCenter and added my esxi servers successfully. I'm trying to configure Orchestrator. When I connect and try to set up the database, I can not connect. I'm not sure what to put. I entered the ip address of the local computer, which is where I installed the vCenter server. When I installed vCenter he installed SQL 2008. I guess it creates the database for Orchestrator, is this correct. If this is not the case, what should I do to get this working. I downloaded SQL 2008 express manager but cannot even see that the database. How to solve this problem?

  Hello

  The vCenter Server Setup does not create a database for Orchestrator.

  Here's what you need to do to set up the database of the vCO.

  First configure SQL Server Express to the remote connection. Here are the steps:

  http://pubs.VMware.com/vSphere-50/topic/com.VMware.vSphere.vco_install_config.doc_42/GUID-0F8AE76E-6BB0-4679-B597-973E4ECB8177.html

  Then manually create the database of vCO. For SQL Server Express, you can use the osql tool (just search osql on the computer on which you installed SQL Server Express). The osql.exe file can be found here:

  C:\Program Files (x 86) \Microsoft SQL Server\90\Tools\Binn\

  or here:

  C:\Program Files\Microsoft SQL Server\100\Tools\Binn\

  The steps for creating a database with OSQL are:

  1. start the osql tool in a command prompt.

  (a) go to the installation directory.

  (b) type osql.exe EI

  (EI means approved connection).

  2. create the database of vCO, vco, for example.

  (a) on the first line type: CREATE DATABASE vco

  (b) on the second line type: GO

  Finally, you can configure vCO to work with SQL Server Express using the interface Configuration of the vCO. The steps to do this are provided as examples in the subject to: http://pubs.vmware.com/vsphere-50/topic/com.vmware.vsphere.vco_install_config.doc_42/GUID841EB9F0-2CBC-44E3-9AC2-4EBAE36F6942.html

  I hope this helps.

• Hyperion 11.1.2.4 Config problem

  Hi all

  While clicking on the Hyperion 11.1.2.4 configuration option, I get error of file jar below. I downloaded all the files of Zio.

  

  Thank you

  LAK

  Hello

  Could you please check if you have installed the components 'Static Content and Weblogic Server' in your server? All deselect some of the components of Foundation, some time it will get deselected

  Thank you

  DWHPC

• shared server config problems

  Dear experts,
  
  Here are my details of environment:
  
  DB: Database 10 g 1 Oracle (10.2.0.1)
  OS: RHEL 5
  
  I have configured the shared servers as shown below:
  
  (1) set the following parameters
  
  Dispatchers ='(Protocol=TCP) (Dispatchers = 2)'
  MAX_DISPATCHERS = 10
  
  SHARED_SERVERS = 4
  max_shared_servers = 10
  
  circuits (unconfigured)
  
  (2) modified TNS parameter like below
  
  I changed the SERVER = DEDICATED Server = SHARED
  
  (3) lsnrctl services
  
  the output of this command shows dispatchers ready
  
  Now come to the question, when I connect to the database using new tns alias, I see 'NONE' displayed 'SERVER' column of the view V$ SESSION. It should have been SHARED.
  
  Appreciate your help in this regard.
  
  Thank you
  
  P

  In shared server configuration when you see the 'NONE' value, it means that it is not a task currently being processed by Server shared for this session. The server column will be infact display the status of "SHARED" If there is a task being processed at that precise moment by the process server shared for this session. So to check, pull a big request and then check the status of the server.

  You can check the shared as server

  Select Server session $ v where machine = "XXXX";

  Neeraj-

• Problema al Extender en disco esxi 4.1

  A saludo a todos los compañeros of este foro.

  Paso a mi explain problema: Tengo virtualizado bajo Vmware Esxi 4.1, a Server 2008 64 bit R2, in el cual tengo back discos duros (office), 30 GB C: y 120 GB D:. Problema mi ha venido a raiz that el espacio in the unidad C: (disco del sistema), quedo muy pequeño. Entonces, procedi a MV e incrementar el tamano para a 80 GB, en the config of the MV. Al iniciarlo posteriormente, vi in the system, the administration of Equipos en, as el disco C: seguia a 30 GB pero that tapeworm 50 GB mas particionados, pero sin iniciar in el mismo disco.

  Reading en Internet, procedi a unite las back particiones, mediante misma tool del Windows 2008. Al reiniciar MV, in the administration of equipos, el disco duro C: is 80 GB, pero UN disco como muestra if lo veo por el explorador, el disco duro con sigue UN size of 30 GB y espacio 0Ko I have.

  Why el Explorador de Windows me sigue showing el tamano antiguo y tanto el administrator of discos, como el diskpart me than muestra el disco-tiene 80 GB?... What me falta hacer o what he done wrong?

  Of photos, the guia thank me orientar can a delivery este problema.

  Saludos,

  Daniel

  Hola

  The problem would be in Quebec no is extendio el volumen en windows, mira following link:

  The partition size is extended, but the file system remains the original size when you extend an NTFS volume

  http://support.Microsoft.com/kb/832316

  How to extend a data volume in Windows Server 2003, Windows XP, in Windows 2000 and in Windows Server 2008

  http://support.Microsoft.com/kb/325590

• Satellite P100-120 overheating running Linux Ubuntu 9.10

  Hello world

  I use Ubuntu 9.10 running on a laptop Toshiba Satellite P100-120; I have a problem of overheating and the fan never put to cool my laptop.
  Looking around, I found that several models of Toshiba Satellite have the same problem and I found that the only solution work seems to update the DSDT file by exploiting this feature on Linux kernels (kernel argument acpi = off is not a solution).

  The problem is that the current Linux kernel of Ubuntu distributions can't take no more (https://bugs.launchpad.net/ubuntu/+source/linux/+bug/395239).
  Given that this problem seems to affect many models of Toshiba/people, I don't know that Toshiba has corrected it to a patch of BIOS; is there a reliable to tell me how I can find this patch?
  I think that we need a BIOS patch because I tried to read the DSDT and indeed it includes bugs (if compile you it with the compiler Intel as described, you can find them).

  Commands to show bugs:
  sudo cat/proc/acpi/dsdt > dsdt.dat
  sudo iasl d dsdt.dat
  sudo iasl tcs - a.dsl

  In the case that Toshiba does not provide a patch, can someone suggest me the reasons (I know that Toshiba is not officially compatible with Linux, but today the Linux community should be accompanied by resellers of computers)?

  Thanks in advance
  Simone Campanoni

  Post edited by: SimoneCampanoni

  > In the case Toshiba does not provide a patch...
  That of the problem. Toshiba doesn't support Linux, especially not for this model of laptop, so you have to search solution elsewhere.
  Support Linux costs money, and why do we have if the books are not delivered with Linux.

  In my opinion the best place to find solution or pickup a few tips useful and info is specialized Linux forums and communities.
  What Toshiba about Linux, you will find under:
  http://Linux.Toshiba-DME.co.jp/Linux/

  Good bye

• WRT-110 34 Firmware Build; Compatible with Windows 7?

  Is the Firmware of 34 build for the WRT-110 compatible with Windows 7 Professional? W7 installed to replace Vista Home Premium on a laptop Dell Inspiron 600 m and have now no wireless networks available and laptop does not detect the WRT-110. Not a problem on my Dell Vostro 1550 as it is still under XP SP3.

  There is no real support from Linksys for this topic re: W7 to their support site, and I'm probably going to NetGear if there is no solution.

  Thus, its seems that the problem has been resolved on the upgrade the drivers for wireless network cards.