NAT is allowed between the Access Point and the WLAN controller?

Similar Questions

• The connection between your cable modem, router or access point, and Internet are broken.

  What is the average message "the connection between your cable modum, router or access point, and internet are broken" and how to fix it?  We use internet provider time warner.  Can I access online using mini jetpack, but not through time warner.  Is the problem with our internet service or hardware problem?

  Hello Terri,

  Thanks for posting your question on the Microsoft community.

  Thank you for details on the issue.

  This problem may occur because of damaged or incorrect network settings.

  I would suggest trying the following methods and check if it helps.

  Method 1:
  Run the network troubleshooting and check.
  Reference:
  Using the troubleshooter from network in Windows 7
  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

  Note: You can run utilities times 'Internet connection' and 'network card'.

  If this does not help, use method 2.

  Method 2:
  Reset TCP/IP and check the issue.
  Refer to this article:
  How to reset TCP/IP using the NetShell utility
  https://support.Microsoft.com/en-us/KB/299357

  I hope this information helps.

  Please let us know if you need more help.

  Thank you

• Diagnostics Windows network, the error reads 'Problem with wireless adapter or access point' and fails to solve the problem.

  «Problem with access point or wireless adapter»

  Hi, I just bought a new laptop & I have the extreme difficulty to stay connected to the internet. When I run Windows Network Diagnostics, error reads 'Problem with wireless adapter or access point' and fails to solve the problem. Help, please... Thank you, Maria

  HI Maria,

  ·         What operating system is installed on your computer?

  ·         You have installed the latest drivers for wireless network card?

  Follow the suggestions below for a possible solution:

  Method 1: Start your computer in a clean boot state in order to check if the applications of third parties or startup items is the origin of the problem.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

   

  Note: After troubleshooting, make sure that you configure the computer to start as usual as mentioned in step 7 in the above article.

  Method 2: See these articles for solve wireless problems:

  Why can't I connect to the Internet?

  http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-the-Internet

   

  How can I troubleshoot network card?

  http://Windows.Microsoft.com/en-us/Windows7/fix-network-adapter-problems

   

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Let us know if that helps.

• The quarters between a bullet point and the text really

  I'm sure I've done this before, but can't remember how. I have a list of bullete (ul) and would like to leave a wider space between the chip and the beginning of the text. I tried to play with the padding and margins, but which moves the text and bullet point.
  I guess that things thinking it can be done...?
  Andy

  Good read through:
  http://alistapart.com/articles/taminglists/

  --
  Concerning

  John Waller

• WRT600N advanced routing problems / use as Access Point and switch

  Firmware 1.01.36 build 4 The WRT600N is connected to an existing LAN and is really only used as a Wireless N access point. There is nothing plugged into the WAN port; only the LAN port. I have NAT disabled. All traffic from a client connected to the WRT600N wireless going very well for the gateway and the Internet router. The customer experience is very good. However, there are a few minor issues as follows.

  1] Setup > Advanced Routing tab has only the following options; to do this, * not * have a picker 'Mode '. NAT, static routing and dynamic routing (RIP).    IS this NORMAL, OR should HAVE a MODE (e.g. switch) AS REFERRED to IN THE HELP FILES?

  [2] even if a connection wireless or wired to the WRT600N works very well, the WRT600N himself is unable to connect to the internet. It cannot connect to NTP to set the time and I can't ping past the gateway router using the ping of the WRT600N diagnostic utility. I ping the gateway 192.168.1.4 port inside, but I can't use the diagnostic the WRT600N ping ping utility something beyond this gateway port. The routing of the WRT600N table is below. THE GATEWAY SHOULD NOT BE 192/168.1.4? HOWEVER THE WRT600N DON'T ME LETS NOT CHANGE IT.

  Destination LAN IP Subnet Mask gateway interface

  192.168.1.0 255.255.255.0 192.168.1.71 LAN & Wireless

  127.0.0.0 255.0.0.0 * LAN & Wireless

  Topic 1. Linksys, used to have a mode option to switch between the modes 'Bridge' and 'router '. The latest routers call it now better NAT power. Gateway mode means THAT NAT is enabled. Router mode means THAT NAT is disabled. The help files are probably a little bit over. But the option is still the same.

  Re 2. It's normal if you use it as only access point (i.e. do not use the WAN port). The router always takes into account that the internet connection via the WAN port, i.e. it will always use the default gateway on the WAN port. If nothing is connected to the WAN port on the router itself has no default gateway and therefore has no access to the internet. Generally, you are not able to establish the default route in either advanced routing page. It is a known limit of these routers if you do not use as a router.

• routers and access points and bridges and lions and tigers and bears oh my

  I studied and I'm still lost. Help please.

  I want the following configuration.

  Bedroom #1: contains my cable modem and a wireless device (wireless router I think).

  Bedroom #2: notebook with built-in wireless.

  Bedroom #3: several components (computers, printers, etc.) that are located on a wired LAN.

  What is the only wireless device that I can add to local wireline in the bedroom #3 for the device on the lan connect to internet through the device wireless in bedroom #1 and also connect to the laptop in the room #2.

  I want to all devices in the home to be on the same network (net sub?)-simple file sharing, sharing printers, etc.

  After hours of searching the Internet, I still don't know if the required device in the room three is a wireless access point, a wireless bridge and a switch, a wireless bridge and a hub, a tin man or cowardly lion.

  Lost in Oz, waiting for the Wiz (i.e. you)

  The Tin man would be the ideal solution. It could carry the USB with the information in both directions.

  Without Tinman, it gets complicated. You have several options. Ideally, I would recommend to connect a cable and not rely on a wireless bridge. It saves you more wireless bandwidth, is faster and more reliable. If it must be wireless:

  Option 1: Get a wireless, as the Linksys wet bridge. A wireless bridge connects to a wireless network existing and bridges the computer connected to the bridge across the network without wire on the other side (i.e. your router, other clients wireless and internet etc.)

  Option 2: Get a more flexible as the Linksys WAP access point. WAP can be configured as a bridge but also as repeaters and other modes. A WAP browser may be preferable to a WET if you also want a stronger additional wireless signal in the 3rd room. However, a WAP browser is much more expensive and more complex to configure.

  If you want only by cable in the 3rd room or the first room wireless signal is strong enough for the customers in the 3rd, just a wireless wet.

  To connect these devices wired in the 3rd room get a switch. Do not get a hub (if you get one free somewhere). Today, most of the devices are switches in any case, I guess. Never connect a real hub in a wireless bridge. A switch manages all the traffic between the devices connected to the switch directly in-house. A hub can cause additional traffic sent across the bridge...

• access points and router

  Hello.

  would it be possible to have two access points wireless that will be connected to a router.

  access points have the same name, if you log on to one or the other with all the problems.

  If this is possible is it all there, I can get information on how to set up.

  Thank you

  It looks like you want a network like this:

  modem - router cable - WAP1)))

  |                                (((sans fil ou les ordinateurs))

  |------------- WAP2 )))

  SSID: even on the two WAP1 and WAP2

  SSID broadcast: enabled on both

  encryption method: even on the two

  encryption key: even on the two

  channels: different on each WAP.  You can choose any 2 channels but ideally, they would be at least 5 channels apart.  Usually channels 1, 6 or 11 are working perfectly.

  Your computer will automatically connect to WAP with the strongest signal.  You can "move" from one WAP to another, however, it is best to do this when you are not actively downloading information.  This configuration would not interfere with file and/or printer sharing.

• It allows me to access "backup and restore".

  My family vista premium is corrupt.  Is it possible that I can back up my system before you wipe the drive and install new operating systems?

  Hi Bbscout,

  1. what happens when you access backup and restore?

  2. you receive messages or error codes?

  Step 1:

  You try to run a SFC scan to find the corrupted system files and try to access the backup and restore.

  You can read the following article to launch the SFC scan:

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833

  Step 2:

  You can also try to perform a startup repair and check.

  Check out the link:

  Startup Repair: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows-Vista/startup-repair-frequently-asked-questions

  If still not working, then you can back up important data to external drives or you can use third-party programs to perform the backup of the system

  Note: The use of third-party software, including hardware drivers can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the use of third-party software can be solved. Software using third party is at your own risk.

  Hope this information is useful.

• The connection between your access point, router or cable modem and the Internet is broken...

  -router

  connection internet dropmy every 20 minutes and again after one minute everything is as before... pls help has me... mb my router is a waste

  Wire? Wireless? Status of other computers (if any)? Router? Network devices? Type of Internet connection?

  Have you other computers can connect to the Internet using the same network hardware?

  You have any kind of 3rd party Network Manager installed, like Hello, Netmagic and the likes?

  Do you have the "Fancy" 3rd part security suits, or as the hybrid of nVidia Firewall Firewall.

  You are using more than one firewall (including native Windows), AV or other security applications active?

  If you use any 3rd part above, try to configure them to work corretly on your network, or get rid of them and see if it helps (RID, means getting rid, not just disable ).

  ------------------

  Assuming that you are connected with the wireless to the router.

  First scan the computer against the viruses and Malwares.

  When you are sure that it is clean.

  These steps and tell us where is the breaking point.

  Check the Device Manager for the wireless card valid entry.

  http://www.ezlan.NET/Win7/net_dm.jpg

  If there is no valid entry, remove any entry from fake and re - install the drivers for the wireless card.

  Check network connections to make sure that you have a network icon/entry wireless connection, and that the properties of the icon (right-click on the icon) are correctly configured with the TCP/IPv4 protocol in the properties of network connections.

  http://www.ezlan.NET/Win7/net_connection_tcp.jpg

  ------------------

  The wireless card drivers much also install utility wireless of the seller.

  Make sure that if there are teas from Wireless Utility of seller does not work with the native Windows wireless utility (Service WLAN).

  ----------------

  Make sure you firewall No. preventing / blocks wireless components to join the network.

  Some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible set up the firewall correctly, otherwise totally uninstall and get rid of its remaining processes that permit the own local network traffic flow.

  If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  party like Hello and NetMagic 3rd network managers can block local traffic too.

  ---------------------------

  Stack TCP/IP work should look like.

  Right-click on the wireless network connection card, select status, details and see if she got an IP address and the rest of the settings.

  http://www.ezlan.NET/Win7/status-NIC.jpg

  Description is the data of the card making.

  The physical address is MAC of the card number.

  The xx must be a number between 0 and 255 (all xx even number).

  YY should be between 0 and 255

  ZZ should be between 0 and 255 (zz all the same number.)

  The date of the lease must be valid at the present time.

  * Note 1. IP that starts with 169.xxx.xxx.xxx isn't valid functional IP.

  * Note 2. There could be an IPv6 entries too. However, they are not functional for Internet or LAN traffic. They are necessary for Win 7 homegroup special configuration.

  ---------------------------------------------------

  A message in the small window that says connected wireless doesn't means that you are really a valid functional connection.

  Above everything is OK, you must be able to connect to the router.

  Connection to the router means that you can enter the IP of the router base in an address bar in one go, being able to connect and configure the router menus see.

  If it doesn't connect to the router, journal newspaper from any computer that can connect to the router wirelessly with a wire, disable wireless security, make sure that the wireless SSID broadcast is enabled and try to connect with no. wireless security.

  Enable security wireless after you eat to make a functional connection.

  
  

  Jack - Microsoft MVP, Windows networking. WWW.EZLAN.NET

• "The connection between your access point router or modem cable, and the internet is broken"

  It is a constant frustration for me sorce. My office gives me this error at least once per hour. I changed the wireless pci card (old one finally died but managed to stay in line!) to a usb dongle, and then to the diffenert pci card, and now I'm in a usb port, which is the same brand as the map oringal that worked. As it is, I can be online long enough to get hope and then... Poof nothing.  I do clean boots, refreshed earworm, did the whole ' IVF it ' was bound to him on a previous post, the netsh command reset. Nothing did. I know that's not the router because all other computers in the House including my laptop can connect.  What Miss me?

  Any help would be loved!

  Hey Tyler,

  Thanks for the reply and keeping the status updated. I appreciate the troubleshooting that you tried it on the computer.

  The issue could be a conflict of others on the computer.

  I suggest you to check the problem in Mode safe mode with networking:

  http://Windows.Microsoft.com/en-us/Windows/Start-computer-safe-mode#start-computer-safe-mode=Windows-7

  If you can't find the problem with Safe Mode with networking, I suggest you perform a clean boot on the computer and check with the question:

  I suggest you follow the link below to find out how to place the computer in a clean boot.

  https://support.Microsoft.com/kb/929135

  Note: Reset the computer in Normal mode once you have completed troubleshooting as a result of the "How to reset the computer to start normally after a boot minimum troubleshooting" section of this article.

  Just reply with the results. I'll be happy to help you.

• I have a compaq presario cq57 notebook pc and my wireless is not solving the problems of work said that the access point and wireless network card works I need help to fix this please

  the internet works only with the ethernet cable and not wireless. I have service with comcast.

  Hi, Antonia.
  Thanks for posting your question on the Forums of community of Microsoft.
   
  1. do you get an error message?
  2. don't you make changes to the computer before the show?
   
  Here are some ways you can follow to resolve the problem:
   
  Method 1:
  Check out the link and follow the steps in the article:
  Troubleshooting your wireless network and Internet access (Windows 7)
  http://h10025.www1.HP.com/ewfrf/wc/document?cc=us&LC=en&DLC=en&docName=c02543015#n55

   

  Method 2:

  Reference:

  How can I troubleshoot network card?

  http://Windows.Microsoft.com/en-us/Windows7/fix-network-adapter-problems

   

  Hope this solves the problem

• There is no communication between devices that are connected to the Linksys WAP4410N Wireless access point?

  Hi all

  I have deployed the new Linksys WAP4410N Wireless Access Point and it works fine. Laptop which is connected to the AP may be able to access the internet. It can communicate with AP and also the gateway IP (IP Router) but it is wireless devices are not able to communicate with each other. In the case of peripheral LAN can communicate with wireless devices. Cannot able to share files between wireless devices.

  Please help me solve this problem. Wat could be the problem here. Stage of Wat I have to take to eliminate this problem.

  Advance thanks.

  Thank you and best regards,

  Chandhuru.M

  Hi, my name is Eric Moyers. I am a network Support Engineer in the Cisco Small Business Support Center. Please use the Forums to Post community of Cisco.

  The title of security without thread/how do you have isolation set up wireless?

  Insulation wireless (SSID) on the inside must be disabled to allow the computers associated with the same SSID to see and transfer files between them wireless

  Thank you

  Eric Moyers. : | :. : | :.

  Cisco Small Business U.S. STAC Advanced Support Engineer

  CCNA, CCNA-wireless

  866-606-1866.

  Mon - Fri 09:00 - 18:00 (UTC - 05:00)

  * Please rate the Post so other will know when an answer has been found.

• [Wireless-Vista] Disable the automatic access point.

  Right then, I had this problem when you play any kind of online game, what microsoft calls a 'feature', when I play a game online, I get a 5seconds or until disconnecting lag spikes every 1-5 minutes, making it impossible to play counter-strike, Call of Duty Modern Warfare 2, Battlefield 2 and all these sorts of FPS games. I read on this vista of "paintings" Wi - Fi point automatic scan has, so I tried with impatience to deactivate, without success, I even once turned off automatic TCP/IP that crashed my computer, so now I'm wondering, how in the world am I supposed to play a game with spikes of major shift due to a malfunction of the so-called?
  If there is a way to turn it off, remove, or simply work around, tell me. I don't care if it is not allowed, because I got it with feautures of microsoft...

  sckizman,
  Have you ever been able to play games online with this computer?
  What version of Vista and what service pack you have?
  You are able to surf on the net normally or you we lag with almost anything on the internet?
  If you have not yet done so, perform a clean boot , and then test your access.  Also make sure that your system BIOS and chipset drivers are up to date.

  Here are instructions on disabling automatic switching between wireless access points:

  Prevent your computer from switching between wireless access points

  Mike - Engineer Support Microsoft Answers
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Tunnel traffic through the Access Point

  I "tunnelenabled" in the parameters of Access Points of JSON: true;

  And on the Access Point associated connection servers config guide recommends not allowing the tunneling.

  The end result is that the traffic is going through the Access Point and not crossing does not connect to the server. The client wants to keep the absolute minimum for the ports open between the objects, so I want to tunnel traffic from the Access Points through the connection to the server, and then click the virtual and physical machines internal who installed the agent to view. Even when I check the options of tunnel on the login server it always appears as if traffic is bypassing the broker for the connections and go straight to the agents.

  
  

  What the configuration change that I do have all the traffic goes through the access points and associated connection servers?

  
  

  Thanks in advance for any help or suggestion-

  
  

  J

  After a lot of trial and error reduced us to certificates that we created for Access Points. HTML5 Blast Bridge did not have other names of the object in the cert. Once we gave them a cert that had the URL and not the SAN (subject alternative names) with the real access Point server names that Blast started working again.

• Droid Turbo could not connect the Cisco access point

  Greetings.

  Since the upgrade to a droid turbo, I was unable to connect to the network without wire of my work. I work in the it Department, but my experience with Cisco technologies and wireless is limited, so I tried to understand why. My previous bike x worked fine. We have a network of all the access points managed by a controller Cisco 4402 running version 7.0.98 of the BONES. I was able to connect to another wireless network that I could meet outside of work, and I am able to connect to the network of my work if I connect it is unsecured guest SSID. Only connections to our 4 secure networks fail. The controller reports that my phone cannot all simply to authenticate. The controller is configured for WPA2 / AES using a key 284 on the particular network, that I am trying to connect. I entered this key manually both via copy and paste. As far as my phone goes, I only tried to withdraw and time networks like tent to start it in safe mode without success. I read on various forums android that maybe it's a problem related to Kit Kat and this kind of problem has appeared on other handsets from other manufacturers, but nothing definite.

  Any suggestions would be much appreciated.

  -Josh

  Let me direct you to two other discussions here on the Droid Turbo forum and the other from Cisco which may help.

  Unable to connect to company wifi

  https://forums.Motorola.com/posts/af633eb3e4

  DROID WiFi Turbo questions

  https://forums.Motorola.com/posts/06a2f3c5ca

  Connectivity issues with Cisco and Moto X (Gen 2) allowed RMC controllers (probably related)

  https://supportforums.Cisco.com/discussion/12331486/connectivity-issues-Cisco-controllers-and-PMF-enabled-Moto-x-Gen-2

  I hope this helps!