WRT 1900AC and Windows 7 on the network or naming issues
Background: I had a Linksys E3000 up and running for about 5 years in a stable network environment. The E3000 is dead, and I put in a new 1900AC WRT to replace. Doing of things set up correctly the main 'name network' in my network poster shows up as a name given to a part of my network wireless. The "Wired" part appears in diagrams and windows, as well as the bands main wirless, but not as the nodal point between computers cable and internet Win7, I want to get the machines to Windows 7 on my network to display the name of cable system in Windows 7, as the primary network and NOT one of those wireless. Almost everything I want to be able to do works very well except for the display of the network card in Windows 7 when I tried to set up a 'House' group that does not yield to my efforts.,.
I use the notation 'suffix' in the name, so is my router on ethernet.
I'm not ready to take this option, partly because I managed to apply each official Linksys/Belkin new update to this firmware to the router via a network connected to the interface of the web browser, app management Andoroid meets most of my needs and that the router is in a section of closet custom built interface built in an old House we updated to convert a vestibule in two closets.
The router sits above a coat bar with the phone and networking hub for a small household of Ethernet wiring devices, coaxial cable and telephone wiring central location includes a small battery assisted power conditioner for the cable modem, the hubs and the router itself as well as the power supply for a connected NAS drive to the port of the router using USB 2.0 speed (the drive is older than the router , but the operating system to wake up when one of the connected devices want to access once it is mapped on the computer. The only precaution I had to take was to not implement the external login to the router with the same credentials used by the Android app that I use to check things and if necessary to restart, etc if I don't want to run a computer and connect in this way. If I had to 'flash' of the router manually, I have to be sure I could worm my way in this cabinet, unplug everything, then consider somewhere, performing surgery and then carry all back and reconnect it. I'm 72 with cataracts of too many years of watching from the CRT in my youth. I prefer not to tighten my back, or down a small stepladder, I need just to get up there where I see things. Perhaps when we move, I'll take with me to Kendal at Oberlin and set up again in a configuration that is more appropriate for a bungalow in a community with large campus wireless available to everyone... This could be interesting. I hope that if will meet my needs "such what" until then. BTW, I'm getting pretty good wireless reception on my terrace outside a two-story built in 1939 with hard plaster, brick slab concrete and brick walls of full course between the router and me!
Tags: Linksys Routers
Similar Questions
-
Unable to connect because of firewall or something, not true of course
When I go to my list of wireless networks, or try to connect to a network it tells me that windows cannot configure the network and if I wanted windows to set up the connection, I need to start the firewall/ICS internet service (ICS) service and then he asks me if I want to start now then I say yes , but then it just tells me that it can't because the assoiciated service is not running, can anyone help please.Hello
I suggest you to follow the steps in troubleshooting this article and check if it helps:
Error message when you try to run the Network Setup Wizard update for Windows XP Service Pack 2, Service Pack 3, or Windows XP Tablet PC 2005 Edition wireless
http://support.Microsoft.com/kb/871122
Also read these articles and check:
In Windows network connection issues
http://support.Microsoft.com/kb/313242
How to troubleshoot wireless network connections in Windows XP Service Pack 2
-
Net 51 with a view system error
I have two boxes of Windows XP that I login as administrator account. I was able to synchronize files, map network drives and can do a tracert to reach one of them.However, when I perform a net view on, I get the following error
51 system error has occurred.
Windows cannot find the network path. Make sure the network path is correct and the destination computer is not busy or turned off the coast. If Windows still can't find the network path, contact your network administrator.
How to make this command work?
Hello
· Your computer is on a domain network?
Follow the steps in troubleshooting this article and check if that helps:
You cannot access shared files and folders or browse computers in the workgroup with Windows XP
http://support.Microsoft.com/kb/318030
See also this article that resembles the same error.
Error when you try to access shared resources on a computer that is running Windows 2000 or Windows Server 2003: "53 system error has occurred" or "51 system error has occurred."
-
I can't use windows Explorer or the network drive mapping to access my NAS drive more.
original title: strange NAS problem
Hi everyone I can't seem to fix this strange problem.
I can't use windows Explorer or the network drive mapping to access my NAS drive more.
I am running windows 7 Professional 32-bit on my PC, and until about a week ago she accessed from my PC very well.The location could not be reached and have not been able to run since said today that I went to update it and the drive mapped. I'm at my wits end.
Here is some info.
I can access to other computers and devices on my network.
I can access the internet.
I have a windows XP PC in the House who can always connect to my fine NAS drive (even if it's not mine).
I PING the NAS drive.
The NAS drive will do the same if connected via cable or by wireless.UPDATE: after the implementation of a shared folder on a Windows XP computer on the same network I am also unable to acsess the part of my PC. So I can assume that I can't browse all share folders or NAS drives on my local network.
Help, please.
Thanks for the help, but I fixed my problem
Here's what I did in case anyone wants to know.
I went into Device Manager and went to network adapters.
I then expanded this section and under view changed to display hidden items.
Several hundred elements appears (for most 6to4 adapters) and I deleted all the.
Then click scan for new hardware.
And... everything works again! YAY! -
How can I solve this problem?
Only Windows 7 computers can join a homegroup.
You need to set up a working group for non Windows machines using the network functions.
And if you have a network printer suitable, then it should not matter what OS you have as long as it has drivers for this printer. I guess that you have a SHARED printer and not a network printer in your question?
-
Original title: no network card
I installed a NETGEAR N300 Wireless USB Adapter on my computer which is a desk top Dell 64-bit running Windows 7 Edition Home Premium. There are five computers on my network. Two of the others use the same model of NETGEAR wireless USB adapt. I removed the Ethernet cable after the installation of the wireless adapter. I can say that the new wireless adapter works fine. When I tried to map the network I got the same message that appears in some of these problems: "Windows cannot create the network map. Responses of the other devices on the network are delayed or there is a router on the network incapatible". I have restarted this computer in SafeMode as suggested in the above problems. I tried other things like disabling the wired connection has always existed for the cable. No effect. Then I tried mapping the network on the other computers. All failed with the same message. All the other four computers are 32-bit. Three of these computers are also running Windows 7 Home Premium. They are the best desktop computers. The other computer is a Windows 7 Starter netbook running. It is the 32-bit computer, always using a cable. That will be replaced with the same wireless adapter model NETGEAR. Anyone know how to fix this or is this a bug? It would be nice of the network software of Windows 7 has worked as it is supposed to. TO.I went the last wired wireless computer and the problem disappeared. The five computers can view the map now without any problems.
-
Cannot open email in Hotmail via Firefox. I have Vista installed on the pc and Windows 7 on the laptop, but cannot access all the features of Hotmail. I tried to clear the cache and restart Firefox, but I still cannot use Hotmail.
Not this problem when I go to Internet Explorer.
Hello, it was noted that the foxit pdf plugin is causing this issue. You can disable this plugin in firefox > addons > plugin until what foxit offers a patch/update for the plugin.
-
Original title: ISATAP adapt #2 does not properly. How can I solve this problem?
My Norton 360 diagnostic report detected a hardware device unusable. The device type is: Microsoft ISATAP Adapter #2 and the device situation mentions that it is working properly and windows cannot load the drivers required - code 31.
I think that it is also affecting my internet connection and disrupt its speed.
Can you please help with this question?
Thank you very much
TonyHi Tony,.
You can try reinstalling the device driver and check if it works.
Uninstall and reinstall the device in Device Manager.
a. Click Start, type devmgmt.msc and press to enter.
b. Locate the Microsoft ISATAP Adapter device
c. right-click on the device and select uninstall
d. restart the computer and check.You can also consult the following article:
On a Windows Vista-based computer or on a Windows Server 2008-based computer, the Microsoft ISATAP map appears with a yellow exclamation mark next to it in Device Manager, and you also receive an error message
http://support.Microsoft.com/default.aspx/KB/932520Hope this information is useful.
-
The SD card is accessible by a BB App and Windows Explorer at the same time?
Hello
My requirement is that the SD card must be consulted by a BB App and Windows Explorer at the same time. But the BB app I developed is able to access the SD card only when the mass storage mode is turned off. Is this how the BB has designed or is it possible to have some logical coding for this?
Thank you
No, this is not possible.
-
I have an update to a site that has been for some time. When I click on the "publish" button, I get the error message: access using your Adobe ID has expired. Check your network and try again. The network is fine (email, browsers work). How can I solve this problem?
Hello
Please see the link below that has the same discussion.
https://forums.Adobe.com/thread/1934384
Kind regards
Vivek
-
Load of Lightroom for Mac and Windows PC using the same serial number
Would I be able to load lightroom for my MAc and Windows PCs using the same serial number?
Yes (if you have purchased the full version).
Thank you
Nikhil
-
Hello
I think I have to click on the network icon in the taskbar at the bottom right of the computer. To connect to the Internet, I have to reset the network adapter named "Local Area Connection" every time. The computer can be idle for 30 minutes or more, and the adapter needs to be reset. I have road runner cable internet and the operating system Windows Vista HP computer n about 3 years. Have no idea?
Thank you all for your help.
Ryan
Try this: configuration panel, Device Manager, expand network adapters
Double-click your adapter LAKE, the power management tab
Uncheck the box; Allow the computer to turn off this device to save power, OK
-
I am trying to install 2 new computers running Windows 7 on one network of 12 others who are running Windows XP, do all need to have the same operating system? I have a printer connected to the computer and cannot access it from my other computers.
You can have virtually any network operating system support on computers on a particular network. The only thing you can't do with Windows 7 computers in a mixed-OS situation is using the new "Homegroup" feature, because it's for Windows 7 only.
http://www.howtogeek.com/HOWTO/Windows-7/share-files-and-printers-between-Windows-7-and-XP/
-
Empty Connections window network and could not start the network connections service
Problems with Verizon router and during diagnosis discovered that the network connections window is empty (found by clicking on change settings for the network and sharing Center map). We are currently connected to the Internet with the new router and Ethernet cable, but the cannot connect wireless (what we could do before) - apparently not to display icons in N.C. window is not necessary to have connections. Found a reference to the network connections service and check it is running as a solution to the window being blank. The service is not running, and when I try to launch it I get "Error 1083: the executable program that this service is configured to run in does not implement this service."
I've seen a lot of suggestions on fixes for the problem of the empty window. I did the sfc /scannnow and found no problem. I tried to update the network adapter driver, but it was very good. None of the solutions seemed appropriate perfectly adapted to this situation. Is this really a problem? Any suggestions on what to do about it? We are about to use an USB adapter until our connection speed and I want to make sure that everything works first. Thanks for any help.
Hi EWright1, we will check the settings of the service.Click Start, type CMD. EXE and press {ENTER}
Type the following command and press ENTER:REG QUERY HKLM\SYSTEM\CurrentControlSet\services\NetmanCopy the output and post with your response.Ramesh,
Thanks for the suggestion. The output of the query to register below.
C:\Users\Edward > REG QUERY HKLM\SYSTEM\CurrentControlSet\services\Netman
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\Netman
DisplayName REG_SZ network connections
ImagePath REG_EXPAND_SZ %SystemRoot%\System32\svchost.exe - k netsvcs
Description REG_SZ objects manages in the network and remote access connections folder, in which you can view the network local and remote connection
.
ObjectName REG_SZ LocalSystem
ErrorControl REG_DWORD 0x1
Start REG_DWORD 0x3
Type REG_DWORD 0 x 120
RpcSs DependOnService REG_MULTI_SZ
ServiceSidType REG_DWORD 0x1
REG_MULTI_SZ RequiredPrivileges SeImpersonatePrivilege\0SeChangeNotifyPrivilege\0SeLoadDriverPrivilege
FailureActions REG_BINARY 8051010000000000000000000300000014000000010000006400000001000000640000000000000000000000HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\Netman\Enum
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\Netman\ParametersHi EWright1,Follow the steps listed under "Reset Network Connections Service registry keys" in this URL:Difficulty for Service (Netman) 1083 in Windows 7 network connections error: -
I'm under Windows 7 Home Premium (64 bit) with internet access provided through a USB modem with a SAM card, or through a wireless router (using the same modem). It comes from the host machine.
I installed Windows Virtual PC.
I installed Windows 7 as the operating system on the Virtual PC.
I installed and activated the integration features.
Now, I have two problems:
1. I activated the HARD disk on the host through integration features settings, but readers do not always appear.
2. I set the first NIC on the guest operating system as the shared networking (NAT). However, I can still access the Internet.
Any help will be appreciated. If you need more information, I would be happy to provide.
Hi James.
This problem is better supported by TechNet. I suggest you follow the link below to send the request on the TechNet forums.
https://social.technet.Microsoft.com/forums/en-us/home?category=w7itpro
Hope this information is useful.
Thank you.
Maybe you are looking for
-
How to disable the option to find my phone, if I phone 4S dead?
How to disable the option to find my phone, if I have Iphone 4S dead? I turned on Itunes and I wanted to restore it, but it's impossible because I find my iphone app is on. Synchronization is impossible
-
How to restore my Satellite 2450 return to factory settings?
Hello I hope someone can help me with this problem? At first look and some of the related son is reading seems easy but... I can't access the menu of BIOS at startup upward or via the control panel. Apparently, I should have a supervisor password, wh
-
Hello. I can get the names of all contacts and groups.How to get contacts who are in a group of some? For example: I hava has three contacts: 1.testContact1 2.testContact2 3.testContact3 testContact1 and testContact2 are formed in a group (testGroup)
-
I have a HPE-477 BC and had a chat with technical support session where I was told that the best solution for my model would be to upgrade my PSU 460w and update my videocard to a radeon 4650. This card seems kind of old for me, and I was wondering i
-
Support Raw D7200 (his absence)?
I just got a Nikon D7200 and have been shooting in RAW, but tried to import photos into Lightroom and get the following message: the files are not recognized by camera raw support in Lightroom. I checked the site and it looks like D7200 raw files sho