WRT54G/PS3 problems

Similar Questions

• WRT54G disconnect problem

  I've been a loyal user of Linksys (CISCO) since the purchase of my 1 Access Point wireless router and 4-port Switch (BEFW1154 v2) in 08/2002. I upgraded to a Linksys Wireless - G Broadband Router (WRT54G v8.00.2) 11/2007. My home wireless network supports; IBM Thinkpad (Windows XP) and Lenovo Ideapad (Windows VISTA Home Premium). A month ago I started having disconnect problems with the WRT54G. The two laptops have been disconnect it. At first I disconnected the supply WRT54G for about 1 minute then plugged in. This has not solved the problem of disconnection. I then tried to unplug the cable modem and power WRT54G. Wait about 1 minute and then reconnect the cable modem, allowing it to reset and synchronization. Then I plugged the WRT54G. This temporarily solved the problem for a few minutes but the disconnection problem returned. I have reset the WRT54G Setup factory default and reconfigured it to my home network. The disconnection problem was not solved by taking this action. I contacted Cablevision that provides my broadband Internet access. They could not identify a root cause of the problem of disconnection. To determine whether the root cause was another thing that the WRT54G, I reinstalled the BEFW1154. I did have a problem of disconnection from taking this action leading me to believe that the WRT54G is bad. I would appreciate any suggestion that could solve the problem of disconnection with the exception of a suggestion to buy a new router. Thank you

  Good to hear that!

  Please click on 'Accept as Solution' to the post that solved the problem so whenever someone meets the same, they immediately know the answer. Thank you.

• DNS server for the WRT54GS v6 problem

  This router running for 2 years without any problem (even on Windows7 since las year), recently it wont let me conect to the internet, network and say sharing that the configuration of the computer center are good but no response from the DNS server is present.

  (Windows 7 RTM Ultimate x 86, Bellsouth / AT & T ISP in Florida.) Conexion ADSL, nine cables ethernet and material held in the best conditions, the network card: Realtek RTL8102E/RTL8103 Family PCI - E Fast Ethernet NIC (NDIS 6.20) (v7.2)

  ================================================================================

  What I tried:

  Reset the router or modem (connected to a Westell 6100), in order to define the default settings and (based on the Web reset and reset buttons)

  Flushing IP in CMD

  Make the web based configuration for my WRT54GS v6, releasing DCHP, renewing, defaults, etc...

  Upgrade the firmware to v1.52.7 (latest) nothing helps, dating back to 1.52.6 original.

  Shows Device Manager hardware works correctly.

  Windows 7 show me a link to view the properties of my WRT54GS when I right click on it, I also see the "Enable" option, but every time I use it I get "Connection Failed!"

  ===========================================================================================

  I'm not much of a tech guy, and read the forum does not help me a lot, so I ask for help please.

  PS: CD installed by default for her with her old EasyLink Advisor without success, tried also the last 2 Lela EasyLink Advisor, nothing helps.

  In addition, there is no default gateway glancing an IPCONFIG in CMD and now there is (192.168.1.1), which I use to enter its web-based configuration.

  That your ISP is a DSL provider, most of the DSL Modem has a DHCP server on them, so they act as a router. From now you the type of connection is NAT behind NAT.

  Order for your Linksys router to work with a DSL Modem. Connect to the Linksys router and on the Configuration tab configuration page, you must modify the "local IP address" to 192.168.2.1 and click on save settings...

  Once the settings are saved, unplug the power to the router and Modem, wait 30 seconds and then plug in the power to the Modem, and once all the lights are cover then you can connect the power supply to the router and check if you are online.

• WRT54GS ROUTER PROBLEM

  I HAVE A WRT54GS ROUTER. TRIED TO PUT IN PLACE. AFTER DOING SO, IT NOT CONNECTING A WIRELESS LESS I CONNECT TO A HIGH SPEED ON THE CONPUTER CONNECTION. SO, IN SUMMARY, FOR A WIRELESS CONNECTION, I MUST FIRST CONNECT TO A HIGH SPEED CONNECTION ON MY LAPTOP THEN CLICK ON CONNECTION WIRELESS AND PLUG THAT IN TOO. THEN EVERYTHING WORKS FINE. OR IS NOT CONNECTED WILL NOT LET THIS WORK. AND YES I'M NOT CONNECTED AT ALL TIMES.

  Thank you

  I see. Do you remember your username and password?

  You need the router to do the PPPoE authentication rather than on your computer. In this way, you don't have to click on the broadband.

  Connect to the router configuration page and follow this procedure. Start with step 7.

• WRT54G v4 - problems

  Hi all.  Hope someone can give me a hand.  The router is connected to a PC running Windows Vista (for the last 5 months), wireless machine is a Windows XP.  Tried to connect to I-net - nothing!  Has been through all the scenarios of "reset" the router and the cable modem.  No solution.  I have-net works well connected directly to the modem.  Because I had this problem B4, checked firmware online but, based on the release date, I think I have the current version. So, contacted Linksys, only to discover that they believe my router can be "fixed", it cost me $40 to purchase an extended warranty for the next 6 months.  I guess in this economy, they try to make money wherever they can.  Of course, my thought is to just buy a new router (which will give me a year of free technical support) and not buy the deal for 6 months - although of course there is an easy solution to my problem.  Once again, thank you for any help.

  Thanks for the suggestion.  I should have checked back sooner, but I solved the problem.  I downloaded the Linksys Advisor and went down through it to get my router online.  I did not update the firmware and was not be allowed access to the router through the 192... the installation program.  Had to go through the Adviser.

• WRT54GS connection problem

  Disconnected last night and everything was fine...  Could not connect to the Internet today...  If I bypass the router, I can connect via my cable modem.

  When going through the router, I get an IP address, an address of a default gateway and DNS1 and address DNS1.  I can't ping the default gateway, DNS1 and DNS2.  The default gateway is a different address when I bypass the router.  When I bypassed the router, I can ping the two default gateway addresses.

  Any ideas?

  Who is your Internet service provider...?

  Do you get the problem on the computer by cable or wireless computer...?

  If you found the problem on the wireless computer, try to disconnect and reconnect the network wireless on the computer. Now, check the ip address and try to make a ping to the gateway & DNS.

  If you have found the issue with the connected computer, then try to reset the router for 30 seconds, power cycle the router and then try to ping the gateway.

• PS3 problems

  For some reason my ps3 does not connect, the signal strength is 100% but it just times out.

  He will be randomly connected BUT cannot broadcast anything or to connect online.

  Or it will be disconnected if someone turns on my computer of mine in the other room

  Should I DMZ the ps3? If so, how.

  Thank you very much in advance

  Note, my 360 connected very well all the time and used to my old laptop connect sometimes like the ps3.

  Routers a WRT610N dual N Firmware Version: 2.00.00 B05 cannot move to 3.00 because of the error "failed to upgrade.

  I guess your router's router v2. Do not upgrade the router with different firmware. The router can cause damage.

  For the intermittent connection on your computer wireless... On the Wireless tab, click Advance wireless settings... Change the interval of tag to 75, Fragmentation threshold to 2304, RTS threshold to 2304 and click on save settings...

  For PS3, try the following settings on the router...

  On the Configuration tab change the size of the MTU to 1365, then click on save settings... Under the Security tab, uncheck block anonymous Internet requests and click on save settings...

  Click on the tab "Games and Applications" and then click the sub-tab "Port Range Forwarding"...

  (1) on the first line in the box, type Application in ABC, in the start box, type 80 and type of box in 80, leave the Protocol as and under type 192.168.1.20 ip address and check the box to enable...

  (2) on the second line in the box, type Application in DEF, in the start box, type in 443 and the type of box in 443, leave the Protocol as and under type 192.168.1.20 ip address and check the box to enable...

  (3) on line 3 in box from Application to the IAD, in the start box, type type in 5223 and type of box in 5223, leave the Protocol as and under type 192.168.1.20 ip address and check the box to enable...

  (4) on the fourth line in Application area type in JKL, in the start box, type in 3478 and 3479 end box type, leave the Protocol as and under type 192.168.1.20 ip address and check the box to enable...

  (5) on the fifth line of type Application in MNO, in the start box, box type in 3658 and type of box in 3658, leave the Protocol as and under type 192.168.1.20 ip address and check the box to enable...

  (6) on the sixth row in the box, type Application in PQR, in the start box, type 10070 to 10080 end box type, leave the Protocol as and under type 192.168.1.20 ip address and check the enable box and click on save settings

  (7) now assign IP on the ip address of your PlayStation:-192.168.1.20, subnet mask:-255.255.255.0 default gateway:-192.168.1.1...

  (8) also assign addresses dns on the primary dns of PlayStation:-4.2.2.2... Secondary dns:-192.168.1.1

  (9) turn off your modem, router and PlayStation... Wait a minute...

  (10) connect the power supply to the modem first, wait another minute and plug the router power cable, wait another minute, and turn on the PlayStation and test...

  * Also reduce the MTU to 1365 on PS3.

• WRT54GS installation problem

  Router v6.0 took the same model in place on another computer which had XP but it won't let me in the web utility via the default ip address in the browser and will not configure an ip address for me to access my broadband with her.  I checked all cables, etc. and when I run the installation disc, it runs it through the settings of your computer "audit" which takes minutes then at the end just jumps to the top of the window of pw and if I type in the default pw it repeats the same process.

  running Win7 64 bit sp1.  Would it be my OS or my 64-bit configuration that is not compatible?

  Follow these steps:

  Turn on your router. Wait 30 seconds.

  Press and hold the reset for 30 seconds button.

  Turn off the router. Wait 30 seconds. Turn on the router. Wait 30 seconds.

  You restart computer. Open your browser. Type http://192.168.1.1/ in your browser and press to enter.

  You should see the router configuration page, and you should be able to access the internet.

  If it doesn't work, go into the TCP/IP properties and configure it with the following parameters:

  IP 192.168.1.100

  Subnet mask 255.255.255.0

  Default gateway 192.168.1.1

  Server DNS 8.8.8.8

  Then try to connect to http://192.168.1.1/ - you should get the router set up page, and you should also be able to connect to internet sites.

  Let us know what works or does not work.

• MAC / PC ACCESS

  MY OLD ROUTER WRT54G IS CURRENTLY PROVIDING THE SERVICE TO MY MAC, AND HE DID A GREAT JOB.  THERE ARE A FEW PC ONLY APPS, I WOULD ALSO LIKE TO USE SO I THINK ABOUT BUYING A PC.  CAN I ACCESS A PC AND A MAC WITH THE HELP OF THIS ROUTER?  IF SO, DO I HAVE TO HAVE THE COMPUTER I USE NOT OFF?

  THANK YOU VERY MUCH FOR HELPING US AN IGNORAMUS TECHNIQUE!

  You can connect a second computer to your WRT54G without problem and both computers can be at the same time.

• PS3 XP and WRT54GS problems

  Equipment: 1 home computer: Microsoft Windows XP Home Edition Version 2002 Service Pack 2 (several others include: Vista with all updates and a MacBook Pro, but the computer is the computer with all the software)

  2 Linksys Wireless-G Broadband Router With Speedbooster. Model WRT54GS

  3 PS3 with all firmware updates

  Problem: I'm having serious problems with practically everything in this configuration... Problem: my router Linksys software gives me the error message: "problem! Internet connection does not work. "Even with this error, I always get a wireless connection on all computers, the PS3, and a PSP in the House.  I did everything the software told me to do and I still get the error message.  Problem 2: At random times when I use the internet options on my PS3 to the internet disconnects from everything, (including the PS3), and I have to disconnect and reconnect the router to get things working again.  This problem tends to occur at random times every time I use the internet on my PS3 but on my PS3 which kills the internet every time, there is a specific function: multimedia Streaming of my XP for my PS3.

  If anyone can help me to solve these problems, I would be deeply grateful!

  LELA update.linksys.com/lela/install/lela.exe update

• WRT54G W7 Media Sharing PS3

  Recently, I replaced my old router with a Linksus WRT54G. I can get Netflix and Youtube, but I'm able to access my files on media of Windows 7 on my PS3. My Windows Media Player recognizes the PS3.

  My PS3 is hard wired via the modem. My previous Motorola modem gave me no problem. I am also unable to use Tversity media server. Is there a setting in the WRT54G that must be adapted?

  I solved the problem of WRT54G. The problem on my network.
  Thank you all for your comments

• PS3 game update stops (WRT54G)

  Hey, I have played ps3 online for more than a year and had a different router in my old House.  We just got the Charter set up in our new House today and have a linksys (WRT54G) router.  I try to update version of a new game, but it gets to 10-20% and stops just to cause to cut wireless.  Sometimes he randomly signed me out, but I was playing COD earlier and it worked fine.  Any ideas why I can play very well, but the update stalls again and again?  Thank you!!

  To resolve this problem, you must update the firmware on your router...

  Download the Firmware from here

  Follow these steps to upgrade the firmware of the device: -.
  Open a page in Internet Explorer browser on a computer hard wired to the router...
  In the address bar type - 192.168.1.1... Leave name empty username & password admin lowercase usage...
  Click the 'Administration' tab - then click on the 'Upgrade Firmware' under the tab-here, click on 'Browse' and navigate the .bin firmware file and click on "Upgrade"...
  Wait a few seconds until it shows that "the update is successful," after the upgrade of the firmware, click on "Reboot" and you will be returned to the same page OR it will say 'cannot display the Page.

  Now reset your router:
  Press and hold the button of reset for 30 seconds... Release the reset button... Unplug the power cable from your router, wait 30 seconds and reconnect the power cable... Now re - configure your router...
  Also, make sure that your computer is configured to obtain an IP automatically, disable any firewall, the security software on the computer before you try to access the configuration page...

  If your Internet Service is cable follow this link

  If your Internet Service is DSL follow this link

  Also on the security of the router tab, uncheck block anonymous Internet requests and click on save settings...

  On the Administration tab disable UPnP, according to the setup of the tab change the MTU size to 1452...

• Fragment of IP problem PS3 (netgear D6000)

  Hey guys, I recebtly was seen this problem on my PS3 where I can't play online and I have test fo a PS3 with an error that comes up saying "the router in use does not support ip fragmebts. I tried all possible solutions and my router is brand new and foesnt used to do this error, so if anyone has a solution that they thibk will help with router thia, I'd appreciate it a lot, thanks!

  Sorry, I'm using PPPOE, PPTP, L2TP, it is said he turned on!...

• RV 120W - problems with PS3

  Hi guys,.

  I have some problems to connect my PS3 to my RV120W.

  Router and PS3 have the latest firmwares. They are connected via wi - fi (distance about 10 mt, signal is good).

  IP of the PS3 is in DMZ (connection does not work with only Upnp), and ip fragmentation is turned on.

  Everything seems to work (type NAT 2), but the download on PS3 is slow as hell. My ADSl is a 6Mb, download speed on PS3 looks like more than ten times lower (I do not know how to test it...). A patch of 200 MB download is a torture.

  Two of my PC are connected wireless, so I guess that wi - fi is not the problem.

  Thanks for your help.

  Hello.

  These products are processed by the Cisco Small Business Support Community.

  * If my post answered your question, please mark it as "acceptable Solution".

  Thank you!

• Configuration wireless router WRT54G without CD - problems with manual installation

  Hello.  I have a WRT54G Router that I've used over the years, because my former cable provider provided me with the router.  I recently switched to cable operators & they do not provide a wireless routers.  I would use my WRT54G Router, but I don't have the cd.  I thought that it wasn't a problem because I can just do a manual installation using the 192.168.1.1 ip address.  I get the pop up window to enter user name & password.  I followed the instructions & just type in the word admin password field & l left the user name empty, but it does not work.  Can someone please?  I know that I can solve this problem.  It is not sensible to spend money for another router when this can be a simple solution.  Thanks in advance for your help.

  Press and hold the reset on the back for 30 seconds and then release.  Wait 10 seconds and power cycle.  Now, try again.