WRT54G2 no signal

Similar Questions

• Router WRT54G2 loses signal shortly after sign on

  I have a router WRT54G2, server printing a wireless G HP 2101 and a Linksys WUSB54GC wireless adapter on my computer, which is a Dell with XP.  When I turn on the system, the router works and the print server connects.  After a few minutes the router stops sending a signal and the print server is no longer functions.  My laptop, which is wireless, is no longer gets a wireless signal.  My iPod Touch is a also wireless, no longer receives a signal. However, the router light continues to blink as if she was sending a signal.   If I stop the entire system and restart the router will begin to send out a signal.  If I disconnect and then reconnect the printer adapter will start to pick up a signal.  After that, the wireless continues throughout the work day.  When I stop and start the system the day after the problem recurs and I have to go through the second stop with the router and the printer.  What is happening and how I can fix this?

  Sunday morning and the router worked for 35 minutes without problem.  The printer adapter also works.  The problem seems to have been resolved.  Thanks for your help!

• Connecting two routers WRT54G2 to extend the signal

  I have available two routers wireless broadband Linksys G (WRT54G2), given to me by a family member. We use one of the routers by itself for some time, but have no adequate signal throughout our House. I decided it would be easier to design the floor plan of the House for you to see his situation compared with the rest of the House on the walls that do not. We have the HughesNet satellite internet which is on the roof just about the location of the modem and router at the bottom right of the image.

  What do you think would be the best location of the main router? I read it would be more centrally located, because the signal travels horizontally and vertically. I just bought a 100' Ethernet cable being the only one that we had what the HughesNet Installer provided us with which is about 4'. I initially thought I would be the cable from main router to the basement where the second router is placed since the signal there is about 1 in 3 bars on my iPhone. The signal on the floor in the ranges of the main room (room at the top in the middle of the image) of 3-5 off 5 bars on my laptop.

  I wanted to just put a post sooner rather than later to see what your views were on the location of the main router and I have to increase the signal.

  Let me know if you have any questions to a better response.

  I have updated the firmware on the main router.

  

  If you want to configure the router as an access point 2 then the connection will be LAN to LAN which means the LAN port of the router port main o the 2nd router's LAN... But before you connect to the main router.

  You should first connect the 2nd router to your laptop, go to the configuration page. Configure wireless settings it is firstly, ethier you set up another name and password is all up to you. Then change the IP address to a number of 192.168.1.x(any fera l'affaire) and disable DHCP... then after that connect to the main router.

• I can link a WRT54G2 V1 to a Zyxel P-660HN51 and it will give me better wireless then?

  Hello

  We received a new modem/router to our ISP. It's the Zyxel P-660HN51 and I wanted to know if my WRT54G2 V1 router connection, would be better for home wireless? Expand it wireless? I think I can, but have no idea how to. I'm pretty good with computers and would need to do. Can anyone provide information on obtaining as a result?

  Thank you!

  Cindy

  Hello DoUReFUNd. The WRT54G2 V1 allows you to extend your wireless network if you cascade with your modem/router. You can mount cascade it as an access point (LAN to LAN configuration) or a secondary router (LAN WAN Configuration). Caveat however, you will get only the G wireless signals of your WRT54G2 V1 router instead of on the P-660HN51 N Wireless signals. For the router cascade, here is a link for reference: cascade or connect a router to another Linksys router

• WRT54G2 - laptop connected but not surf the web

  Hello everyone, please someone help me... I bought a WRT54G2 and configured correctly... my desktop computer works fine, but my laptop is a problem... I connect to the router via WiFi from via a cable, it connects to the routher and I see it connected, but I don't get internet signal... do I have to open anything in the router?

  Thank you.

  Well well, for some, strange / funny / slash reason I won't be able to understand, I followed all your instructions with no luck... but one night I fell asleep unplug the router of the AC and when I plugged the next morning, all the router settings were reset, as if I flashed. So now I can connect and surf the web. Is this problem comes back, I'll post another message.

  Thank you!!!

• Connect Eternet Switch (for cable connections) AND WRT54G2 to WET610N

  Hello

  In my office, I have a cable modem that is connected to my main router E4200. All my gear (except my Ooma) is served by the E4200. The E4200 broadcasts a wireless network.

  In my basement, I have a Wii / entertainment center. The E4200 to the floor signal is not strong enough to stream videos.

  I bought the WET610N and have successfully set up to interact with the network of wirelss E4200. I can wire my laptop for the WET610N and check that the internet works fine.

  However, the Wii needs to connect wireless. I have other equipment in the basement who benefit of an internet connection. So I want to A) connect the Workgroup Switch 8 ports 10/100 ESXS88W I the WET610N * AND * also broadcast a wireless signal in my basement (assuming that the wireless network I see in the basement is the same as that of the floor which has not benefited from the 'old' WET610N).

  How can I configure my WRT54G2 to broadcast a wireless signal in the basement so it relies on the E4200 signal served by the WET610N, while having the work group switch offer connections wired to my other equipment (such as Dish Network receiver)? It doesn't seem to work by simply plugging the WRT54G2 in workgroup switch.

  Thank you!

  If I'm not mistaken, your configuration looks like this:

  E4200 (()) WET610N - EZXS88W

  * Wi - Fi brackets and cable connection indicatd by dashes

  If you want to connect a WRT54G2 to broadcast a wireless network in your basement, you need to connect to this router (using the port 1,2,3 or 4) to your switch. you need to change the IP address of the WRT54G2 192.168.1.2 so that it is not in conflict with the E4200; Disable the DHCP server (since the E4200 is already the DHCP server).

  that should do it.

• Optimize the Signal?

  I have a WRT54G2 1.5 version...  I wonder if there is a way to optimize the signal because I still have a low when the Xbox Live connection or using my iPod Touch when I'm hence my router is downstairs.  Re-creation of the router is sometimes useful, but not as much as I'd like.

  Connect the computer to the Ethernet 1 port router with the Ethernet cable.

  Open the Internet browser and in the address bar type http://192.168.1.1 . Connect to the router configuration page. the default password of the router of admin, leave the empty user name.

  Click the wireless set the configuration found in the manual. Change the channel to 11 wireless. Save the settings.

  Click settings wireless Advanced tab change the tag to 75 interval, RTS threshold to 2307 and threshold of fragmentation at 2306. Save the settings. Cycle power to the router.

  Try to connect to the wireless network. Check if it works.

• WRT54G2 does not connect.

  Hello

  I searched the forum and cannot find a question like the problem I have.

  I tried to set up my WRT54G2 and everything seems ok.  Installation work and the computer recognizes that the network is there.  But it provides no signal on my computer, if I connect directly or wireless.  The problem seems to be with the WRT54G2, and maybe it's a malfunction.

  I run my DSL connection via a Motorola Netopia 2210-02 ADSL2 + and connect the WRT54G2 to this unit.  what I notice is that the 'activity' of my Netopia camera light does not illuminate when the WRT54G2 is connected.  This is true if I try to use the WRT54G2 wireless or wired directly to the computer.

  Does anyone know if this is likely to be a problem with a broken unit?  Or is it an installation problem?  As I said, I didn't have no problem whatsoever under Setup and the computer recognizes that the WRT54G2 sends a signal, it is enough to connect to the internet.

  Thank you

  Joe

  Hello

  I wanted to thank you for your help.  The problem has been resolved.  I simply had to change the IP address of 192.168.1.1 to 192.168.2.1 and all my problems have been resolved.

  Thank you.

  Joe

• WRT54G2 problem appears after the firmware update

  Hi everyone, a newbie here. Nice to meet you all and thank you in advance for your help.

  Here's my problem. I have updated the firmware on my router for 1.0.04)is Sunday, and then there are problems on my router.

  1 have a weaker signal.

  2. the router cannot detect my internet just as it has been in the past. I have to type in my PPPoE setting for example my user name and password in 192.168.1.1. Furthermore, I use AT & T DSL.

  3. my internet will totally drop off after several hours. I have to reopen it and the modem power on & off switch.

  So I want to know if I can downgrade the firmware back to 1.0.01 or is there any other setting that may help me get but it? A list of steps is better.

  Thanks again in advance and have a nice day.

  If you haven't already done so, try to do a hard reset, hold reset button of the router for at least 30 seconds with the power connected to the router, and then reconfigure as needed.

  Since I use your & AT T DSL, you can reconfigure the DSL modem, so it don't the PPPoE connection and then reconfigure Type Automatic Configuration - DHCP Internet connection router.

  There is another question that may arise with an AT & T DSL modem. My Speedstream 4100 & AT T DSL modem put the IP address 192.168.1.1 for the router WAN/Internet port. If the router is configured to the default settings, there will be a conflict between the modem and the router and none of router devices connected will be able to access the internet. The solution is to change the IP Address of the router to the router on 192.168. 2.1. Restart all router connected devices after you have made this correction.

  Also with some model WRT54G2 (happens on my router WRT54G2 V1) the wireless signal will go offline when a wired computer is started. When this happens, the work around is the power cycle that the router once the wired computer has started, or log in to the router, go to basic wireless settings page and click on the button Save the settings. Then the wireless signal comes back to the top and wireless devices will resume their connection.

• Speed drop after Firmware update WRT54G2 wireless

  I have a WRT54G2 V1, which began to do a lot of loss of wireless signal, the wired computers are always connected to the net, completely wired computers lose the connection. I decided to try an update of firmware for 1.0.04)is Build 5. and the flow has fallen by 2 members! The wired computers have the same speed of connection as before. I feel is one of the parameters of connection in advance, don't know how tweek. I already went through all the different voltages without success.

  Help!

  So all settings are the same after the update of the Firmware but I went a head and did a reset and all, still half speed re-admitted. It fixed by a new round of power. Also since updated the firmware and reset have not had problems with the router stopping broadcasting either.

• Questions of signals (s7 edge LTE - iPhone 7 Plus 4 G/E)

  Hey guys,.

  I know there are a lot of posts on this topic but I can't really find the one that corresponds to this...

  So I moved from s7 Edge for iPhone 7 more.  Since the switch, I have signal problems. Where, normally, I LTE 3 bars on my edge of s7, I now get 4g and E even on my iPhone 7 more. What is going on!!!  BTW, I'm on T-Mobile.

  Thank you

  Hey Greggaa,

  Thank you for being a part of the communities of Apple Support.

  If you get a poor cellular signal where you used to get full LTE signal, then it might be an update available for your iPhone carrier.  Please follow the steps in the article to check this update:

  Update the settings of your company on your iPhone or iPad

  Take care.

• iOS 10 no signal problem

  I have an iPhone 5s (model 1533) and after the update to iOS 10 I can't get a signal, I tried a full restore and update and also reset network as well as the obvious reboot. First, he would get a signal a little while but if I tried to make a call, it would go directly to no signal, it also seems to have the power of the weak wifi signal too, related? Must say that I had a lot of problems with my apple stuff recently, at the end of my home! All ideas welcome please?

  I had the same problem on Verizon.  I fixed mine by going to settings, cell and disable roaming data and then on again.  Its happened twice so far, as well as a few other bugs.  iOS 10 is probably the worst launch of iOS.

• Why my MB Air decreases the wifi signal

  My 2012 13 "core i5 MacBook Air running different operating systems will remove the wifi signal and it is getting worse. someone at - it a reason why?

  How your MacBook Air running different OS version? However, the Wi - Fi signal fell to each version?

  This always was a problem or just started to happen? Up to now, what did you do to try to solve?

• The dual SSID Signal interference

  I have the cable and Internet provided by AT & T.  I mainly had Comcast when you live in different parts of the country.  I am owner of an Airport Extreme and Time Capsule I used previously to set up the network internal in addition to the SSID broadcast material of the cable company.  I never had a problem before using AT & T.  I noticed that the Internet speeds both the provider of cable and speed on the internal network have been seriously degraded.  I was unable to stream movies.  After several attempts to solve the problems with AT & T and myself, I found the problem: it seems to be interference of signals between AT & T and Airport Extreme material each broadcasting separate SSID in very close to one another.  I got the Apple hardware, and the problem was solved immediately.  While I'm happy to have it fixed, I don't miss the advantage of having the internal network using Apple devices.  What are my options?  Is it correct that I can't use the Apple devices to extend the SSID signal emissions equipment AT & T?  I think the problem might be solved, perhaps, if the two gateways were not close to one another, but I do not have another spot to plug the Airport Extreme.

  Is it correct that I can't use the Apple devices to extend the SSID signal emissions equipment AT & T?

  Unfortunately correct.

  Apple routers work that to extend another router from Apple... no other brand is invited to the party.

  I think the problem might be solved, perhaps, if the two gateways were not close to one another, but I do not have another spot to plug the Airport Extreme.

  Separate the two routers as much as you can... I always recommend 6feet or about 2 M. If they are closer than this really a wireless should be turned off. Only for this case deactivate the ATT router instead of your apple.

  There are enough wireless channels to run 3 wireless routers close to each other.

  Sometimes the automatic separation of channels does not work and you need to get and change physically.

  Use wireless diagnostics (many versions available, but it is built into Mac OS since the Mountain Lion)

  There are a bunch of tools... the actual diagnosis is not particularly useful in my experience.

  

  Open scan.

  

  You will need to click on it to see the whole thing.

  Now, I have a few questions... first, I'm not showing noise... This is just my configuration problem. But you should see RSSI (signal level), noise, channel, band, width and country.

  Watch channels... My installation has some problems because most of the 2.4 ghz is using channel 11.

  The diagnosis tells you even what channels to use.

  

  I can open airport utility and select one of the units in issue. Click the icon from the airport... Click on edit in the preview.

  

  Go to the wireless tab.

  

  Click Wireless options

  

  Change the automatic 2.4 ghz regardless of the channel you want.

  

  Save and update from the airport.

  Especially for 5 GHz, I think that your stay on auto should be fine. It is more short-range and isn't usually a big problem.

  Note also the signal strength really counts... things go wrong if you don't have enough separation and the signal strength is low.

  2.4 GHz, there are only 3 channels Alcan... 1, 6, 11

  Although Diagnostics of scanning you will offer between channels... do not be fooled that this corrects the problem.

  Read the wiki for wireless lan.

  https://en.Wikipedia.org/wiki/List_of_WLAN_channels

  Channel 6 for example is actually peak signal to 6, but it covers 4 to 8.

• No signal iPhone 7 more

  I was able to find an iPhone 7 more black well, worked all day, slept and next morning no cell report real message was no Service.  I tried resetting network services, remove the SIM card, reset the phone.  I tried same sim in another phone and it works.  Seems to be a similar issue to those who have the problem of airplane mode.  There is now no point on the phone that I want and I'm stuck with a dead paper weigh.  Any ideas?

  I have a similar problem. I have an iPhone 7 Verizon and it also loses the signal while driving. It says no Service. Restart the phone temporarily solves the problem. I called Verizon and they have other reports and said that Apple is aware of the issue. I hope it's just a software fix!