WRT54GS static dns issue

Similar Questions

• EA6200 IS NOT WITH THE HELP OF STATIC DNS

  I had the EA6200 weeks and set up out of a NVG589 of TA &T; has not worked well, no problem at all using the AT & T modem as the DNS server.  I just noticed that there is an update of firmware for this model, up to 1.1.41.164830; so, I got the router install it.  But now I was making errors on all my devices, saying that the DNS server is not responding.  I have sailed on the section of 'Connectivity' and the 'Local network' tab and my static DNS is as it was before the update of the firmware.  But when I connect a device to the router, the network parameters show that she tries to use the network personalized ID I have install the router, rather than the static DNS that I've locked in the router settings.

  The only way I am able to get online and write this message from my laptop now is because I had to go into CMD and put the static DNS for the laptop computer, manually, to the IP address of the modem from AT & T.  DHCP should be handling this according to my settings, but it's not.

  If anyone has experienced this before? Is this a firmware issue? Should I go back or understand this?

  before you go back, try a factory reset by pressing the Red reset button until it restarts, then cut off the power. After 10 seconds the power turn on and when it is completely started config it from scratch and it should be ok. Of course this will eliminate all the settings you had including the password which will then return to "admin" be aware of this before you start.

• DNS issue when workstation has static IP

  Hello

  I created a SonicWall the other day, and I'm having a problem on 2 workstations. These two work stations have static IP addresses. Other workstations using the DHCP protocol. Those who use DHCP can access Internet without problem.

  Computers with static IP address can access the Internet, but only if they're ready to use the DNS servers of the ISP. If I put them to use the SonicWall as primary DNS, they can't get out to the Internet. Thus, if the SonicWall is 10.0.0.1 the following will not allow Internet access

  IP/subnet: 10.0.0.100/24

  Gateway: 10.0.0.1

  DNS1: 10.0.0.1

  DNS2: another value

  but change DNS1 to 24.92.226.11 (Time Warner DNS) will allow Internet access.

  Any thoughts?

  The SonicWALL cannot act as a DNS server. If you don't have internal DNS I suggest to use the public DNS as google 8.8.8.8.

  Kevin

• WRT54G and DNS relay?

  Hello everyone - I am considering the purchase of a unit of WRT54g.  Have a question...

  I intend to have the IP-side WAN to give it to me via DHCP from ISP.  I expect that the ISP will provide info server DNS as well on the WAN side.

  Is it possible to pass transparently this DNS information to my LAN using DHCP clients?  I'm not statically configure DNS for DHCP clients on the LAN side.  I'd rather them use some address DNS is given to the router.

  Is this possible?

  Thank you
  Scott

  Yes. This is the default behavior. According to the version of the firmware on the server and the router DHCP on the router either directly affects the DNS of the ISP servers or he assigns the DNS relay router, i.e. 192.168.1.1 aka it's own LAN IP address.

• EA6500 - DNS issue

  Devices connected to my EA6500 not connect to internet unless I put a DNS (8.8.8.8 for example) to each device. This problem occurs with or without wire. My iphones are the only devices that seem to get a DNS from the router. All other devices (DirecTv genius, Xbox 360, laptop, Lenovo, Sony Blu - Ray, AppleTV, nest the players) get a 192.168.1.1 in the DNS domain and does not connect until I put a different DNS.

  I tried to reset the modem, router. I have reset the router by default and reinstalled does not. Someone at - it suggestions?

  Comcast service 50/10

  SB6141 Cable Modem

  It is not a question of what DNS server I use. It has been more than one server DNS has been passed to my devices.

  I think I found the issue however. I'll post details later, but in a nutshell the DNS 1, 2, 3 fields don't were not filled in one of the configuration menus. I put some and my devices worked without manual entry on each device.

• WRT54G static assignment of IP addresses?

  Hello everyone, I have a WRT54G v4 (FW 4.21.1) router wireless and I am trying to configure to assign static IP addresses to my devices.  I have two wired devices, and seven wireless devices and IP addresses are constantly evolving. This is normally no big deal, one of the wired devices is my printer (connected via a cable etherner). The only way I can install this printer to devices is to a standard TCP/IP installation, using the IP address assigned automatically. My question is, can I assign one address of the printer so that I can install it on the rest of devices with an address? Or do I have to assign an address to each machine? And how even statically assign? I know how to connect on the router and am familiar with the integrated navigation page, but I do not see a table of MAC addresses anywhere. I have the latest firmware as well. Thank you in advance for the answers!

  The WRT54G does not support a DHCP reservation. You set a static IP address on the printer. I have not heard a network printer on which you cannot set a static IP address...

• WRT610N V1 Firmware 1.00.03 B15 DNS issue

  I have improved my WRT610N the other night 1.00.02 B10 and since my router cannot properly spread the DNS to my LAN from my U-verse RG server info.

  The only way I could make it work is to configure a static IP address for the internet. It's NOT ideal when my IP changes.

  I have U-verse RG installation correctly for use with my router. DMZPlus mode enabled on the RG and passes just all the info to the router so as a modem, so it is not like 2 routers on a network.

  I have a static IP network on the side LAN and I have always used the IP Address of the router (192.168.1.1) as the gateway and default DNS on my machines. Previously, he always shot info DNS of the RG and all was well, but ever since 1.00.03 B15 no go. (I think it has to do with the 'vulnerability DNS problem solved' listed in the change log)

  However, I can ping tests and trace roads since within the configuration of routers diagnostics page and everything works fine it just doesn't propagate to my network.

  Everything seems as it should on the status page.

  I tried full reset of the router and re-configuration with only about an hours of operation until the DNS problems are back.

  I tried to manually in the DNS server on my machines info and that seems to work on SOME of my devices.

  I'm really at a loss here because it worked very well before and even on previous Linksys routers I've had. I really don't like manually enter the DNS information on each device, I like the router to automatically manage all this as it still allows with this and other models of routers, so it does not solve the problem on all devices.

  I have not tried the downgrading of firmware or update to the V2 firmware yet.

  I appreciate any help and insight that anyone can give to this question.

  Thank you!

  OK I don't know what the deal is here.

  I logged into the U - verse RG changed the IP 192.168.2.1 and subnet 255.255.255.0 after restart of the RG the WRT610N to the correct DNS numbers changed the subnet to 255.255.253.0 in itself but it worked fine. So I changed the IP back to 10.0.0.1 subnet back to 255.255.0.0.

  WRT610N always pulls the correct DNS numbers and everything seems to work as it was before the update of the firmware.

  This may be a bit premature, but I think he's fine now.

  RG is still connected via the WAN on the WRT610N part.

• DNS issue

  A new PC, enable us the DHCP and try to add to the dominating Server 2013 but cannot be added because can not find the server via DNS

  A lost PC work dominates, the DNS do not respond, once a Flush DNS and the DNS registry highlight function

  Hello Rafael,.

  Thank you for visiting Microsoft Community and we provide a detailed description of the issue.

  By the description, I understand that the problem with you try adding dominates Server 2013.

  I can understand the inconvenience that you have experienced and will try my best to help you.

  To get more information about it, we have a dedicated forum where these issues are dealt with and would be better suited to the TechNet community.

  Please visit the link below to find a community that will provide the best support.

  https://social.technet.Microsoft.com/forums/en-us/home?category=WindowsServer

  I hope this information is useful.

  Please let us know if you need more help, we will be happy to help you.

  Thank you.

• Static Nat issue unable to resolve everything tried.

  Hello

  I have a cisco asa 5515 with asa worm 9.4.1 and asdm 7.4

  I have problem with configuring static nat, I have a server inside which ip is 172.16.1.85 and

  my external interface is configured with a static ip address.

  Internet works fine but cannot configure static nat...

  Here's my config running if please check and let me know what Miss me...

  Thank you

  ASA release 9.4 (1)
  !
  ciscoasa hostname

  names of
  !
  interface GigabitEthernet0/0
  nameif outside
  security-level 0
  IP 151.253.97.182 255.255.255.248
  !
  interface GigabitEthernet0/1
  nameif inside
  security-level 100
  IP 172.16.1.1 255.255.255.0
  !
  interface GigabitEthernet0/2
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet0/3
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet0/4
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet0/5
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Management0/0
  management only
  nameif management
  security-level 100
  IP 192.168.1.1 255.255.255.0
  !
  boot system Disk0: / asa941-smp - k8.bin
  passive FTP mode
  object remote desktop service
  source eq 3389 destination eq 3389 tcp service
  Description remote desktop
  network of the RDP_SERVER object
  Home 172.16.1.85
  outside_access_in list extended access allow desktop remotely any4 object RDP_SERVER
  pager lines 24
  asdm of logging of information
  Outside 1500 MTU
  Within 1500 MTU
  management of MTU 1500
  no failover
  no monitor-service-interface module of
  ICMP unreachable rate-limit 1 burst-size 1
  ASDM image disk0: / asdm - 743.bin
  don't allow no asdm history
  ARP timeout 14400
  no permit-nonconnected arp
  !
  network of the RDP_SERVER object
  NAT (inside, outside) interface static service tcp 3389 3389
  !
  NAT source auto after (indoor, outdoor) dynamic one interface
  Access-group outside_access_in in interface outside
  Route outside 0.0.0.0 0.0.0.0 151.253.97.177 1
  Timeout xlate 03:00
  Pat-xlate timeout 0:00:30
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  identity of the user by default-domain LOCAL
  Enable http server
  http server idle-timeout 50
  http 192.168.1.0 255.255.255.0 management

  Telnet 192.168.1.0 255.255.255.0 management
  Telnet timeout 5
  SSH stricthostkeycheck
  SSH 192.168.1.0 255.255.255.0 management
  SSH timeout 5
  SSH group dh-Group1-sha1 key exchange
  Console timeout 0
  VPDN username bricks12 password * local store
  management of 192.168.1.2 - dhcpd address 192.168.1.254
  enable dhcpd management
  !
  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  dynamic-access-policy-registration DfltAccessPolicy
  username, password imran guVrfhrJftPA/rQZ encrypted privilege 15
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  !
  global service-policy global_policy
  context of prompt hostname
  anonymous reporting remote call

  ciscoasa #.

  Hello

  Change this ACL: -.

  outside_access_in list extended access allow desktop remotely any4 object RDP_SERVER

  TO

  outside_access_in list extended access allowed object RDP_SERVER eq any4 tcp 3389

  Thank you and best regards,

  Maryse Amrodia

• DNS DHCP pool (internal DNS issue)

  I know that we can implement several DNS server under DHCP pool. But I want to assure the order.

  I have several branches.

  Let's say 1 division Office has a router with 10.30.1.1 as a default gateway.

  Our internal DNS is 10.0.0.1 and 10.0.0.2 as Pri and dry.

  My order of DNS server is as below.

  1 gateway

  2 internal DNS

  3 public DNS provided by ISP

  I saw two or three questions when I put the internal DNS first. Special situation is when IPsec does not work, users could not access the internet through domain name because they had internal DNS that is not accessible.

  But when the door is of the first order, I don't know if users are able to access the internal Web site because gateway DNS does not have internal DNS records.

  So, my question is which. What should be the best order for installing DNS under DHCP between default gateway, internal DNS and DNS?  Our current configuration does not have same gateway address, there only internal DNS addresses only.

  dhcp pool IP CCP-pool1

  Network 10.30.1.0 255.255.255.0

  name of domaine.org

  router by default - 10.30.1.1

  -10.30.1.1 NetBIOS name server

  10.30.1.1 DNS server 10.0.0.1 10.0.0.2 24.25.5.60

  (1) I think your logic is right.

  (2) you are welcome.

  (3) I now see how the link relates to question 3. Yes, the difference between the specification of a name server for the router itself with ip name-server and clients by using the dns server is an important point.

  I am glad that you tell us that you had ip domain-lookup because it would have been my follow-up to the issue. Can you tell us exactly what the response of the router was when you tried to ping google.com? I suspect it's something in your router config. You can post a copy sanitized the router config?

  Thanks for the compliment - and for points.

  HTH

  Rick

• Strange Cache DNS issue (maybe?)

  For the last two days, I was frustrated by my inability to set up a custom domain Outlook.com in 2013 Outlook on my computer, and then yesterday I finally realized that the issue is more precisely with my computer (by adding the domain to any other computer or at work is fine)

  The problem is that it seems to be something implemented caching on my computer. This has to do with a security for a Web site certificate that I participated in the test.
  I checked the store of certificates on this computer and there is nothing for that Web site.
  I also did the ipconfig/flushdns, does not
  And I stop each device on the network, including the cable modem / routers, but still the problem persists
  Any idea where I can look for something related to certificates or DNS which could be stored somewhere that I should delete / flush?
  Thank you...

  Hello

  You can also post the same question on the Forums of Microsoft Office, since we have a dedicated support for Office products.

  Microsoft Office Forum: http://answers.microsoft.com/en-us/office/forum/office

• Static DNS records; Bad, good ugly.

  Hello

  always when I want to add the new ESXi5 host to vCenter I creat static record on DNS, after this host to join in DC and then add the host to vCenter.

  is it possible to join my poor host to vCenter without creating records staics on DNS manually? He can see that when joining ESXi host DC or a way to create the dynamic DNS record?

  Unfortunately the-host, these must be manually created in all cases. Take a look at Re: ESXi 5 in AD / DNS configuration where Troy describes the reason for this.

  André

• DNS issue on the Windows Server-based host computer

  I encountered a problem which is probably easily solved - but I've been browsing the net for days already and cannot find a solution.

  First, I will describe my basic setting.

  I run a Windows Server 2003 host in a simple configuration of the House, connected to an ISP. I have my own domain name, which is hosted by another company. My local domain name is called "mydomain.local"; My overall domain name is called 'mydomain.eu '. I send a large number of specific services on my local server, using the settings for my domain name host. So my Windows Server is called orakel.mydomain.local; My Web page, which is hosted on the outside is www.mydomain.eu, but I use my local server for ftp access, so ftp.mydomain.eu is sent to my local IP address; my router forwards to orakel.mydomain.local and my ftp server on Windows Server handles the traffic. This Setup works very well and allows me to administer my internal and external DNS settings.

  My main server uses 192.168.0.1/255.255.255.0 and is also DHCP/DNS server for the rest of the network.

  As I plan to switch to Linux, I installed Vmware Workstation 7.1 on my server (orakel.mydomain.local). I created an image, add a static IP (192.168.0.50) in this image. The VM network adapter has filled and directed to my physical network adapter. I added an external debian record, achieved to my IP static, just like I did with my ftp, usenet etc - thus, debian.mydomein.eu is directed to my fixed address, that is passed (by my router) to the orakel.mydomain.local (192.168.0.1)

  And then I ran into problems. I want to access my image debian from the outside world and cannot get this to work.

  When I'm on-site talk, I use 192.168.0.50 to access my image. I added a DNS a record on my * local * (debian-> 192.168.0.50) DNS server, while debian.mydomain.local also works very well as long as I'm using my own local network.

  But I want to use debian.mydomain.eu, because it will allow me to access the image debian to other places as well. I can't find a way to achieve this. When I use debian.mydomain.eu, I get redirected to my router which redirects me to orakel.mydomain.local, but it ends there. I run Apache on both my windows server and in the image virtual debian, but I ended up always on my windows http server, not on my server debian.

  When I change my router settings to forward port 80 to 192.168.0.50, it works, of course - the virtual machine image works fine. But how do I get my windows to redirect some of the names of servers to virtual images? I would like to execute WEBDAV in a VM-image debian and keep my existing Windows-local http server running as well. Thus, redirect ports on the router clearly won't work, such as HTTP and Webdav to use port 80. I have been looking and trying to not solve or no this result. I * know * that virtual machines are used only to share physical resources for a number of Web sites, and that's just what I'm trying to accomplish!

  Where do I need to make adjustments? What is a VM settings somewhere, or should it be solved by the guest operating system DNS settings?

  Paul Kooistra

  Hello Paul,

  DNS only don't name resolution. So, given a name, which is the corresponding IP address known. What I understand, you want to have multiple servers in order to be accessible from the Internet for the same service (ie. http) using the standard ports and this is where your problem lies. Unless each of these servers are addressable landscape in terms of sound system you will not be able to do it without using a part of the trick of my previous post.

  Your ISP gives you more than one external IP address? If so, do you have a firewall that can handle more than 1 address NAT?

  Kind regards.

• Login screen - DNS issue

  We seem to be affected by intermittent empty login screen on my company's website, but only for the microsoft login page, the login page Skype charges well.

  Loading Skype upward, you get this screen:

  

  And users choose 'Microsoft account '. They should then see this screen:

  

  Instead they get this:

  

  Inside, there is a warning message stating the following:

  "This page contains errors. Go back'

  The site uses OpenDNS to filter queries DNS for computers and politics is quite locked.

  On any affected PC, if:

  -Close Skype

  -Run the DNS settings to something like 8.8.8.8 (google DNS server)

  -Load Skype

  The login screen (image 2) loads normally. The user can connect and I can then folding the DNS settings on the OpenDNS server and there is no other problem.

  Which means that Skype is trying to communicate with a Microsoft/Skype server somewhere on the interent and because it is not on my whitelist OpenDNS it gets blocked and it fails as in Fig. 3.

  My question can someone tell me what is the server? I went through the OpenDNS logs and the white list a bunch of stuff from microsoft and other things related to the certificates, but still no luck.

  Evetually I took the suggestion of Techfreak and sniffed packets with wireshark. Was annoyed to discover that the root cause of the problem is strangely named sb.symcd.com.

  Some quick Google-fu led me to a page that said that this area should be on a whitelist for Lync facilities. Hmm.

  Why microsoft couldn't use Server intuitive/descriptive names more is a mystery. In any case, I have whitelisted *. symcd.com and of the limited testing it seems to be resolved.

• Why static DNS server address round get the unable to download updates 8024402C problem in WIN7?

  I got a work around for the unable to download problem error 8024402C updated on a new laptop WIN7 Starter running.  I get regarding the size of the update and starts to download, but nothing comes down.  The solution is to change the DNS settings of default for a manually configured DNS server, for example 4.2.2.2.  It works, but I wonder why, and what is he moving?

  The auto setting worked when I was in the United States connecting via a LAN in the hotel but not here at home in AUS, where the settings auto search for an address DNS 192.168.1.1, my router ADSL/2.  All other functions like Skype, Adobe updated, download of MS shop, all work very well using 192.168.1.1.  Also my XP Home PC, all use 192.168.1.1 and they get the updates without any problem.

  -What is someone able to explain why?

  Thank you

  Hi ascidiens,

  The 0x8024402C error codes typically occur because there is an incorrect character in substitution of proxy settings. Basically, it's something to do with the proxy of your connection settings network and which can be overcome by changing the DNS settings in manual.

  Bad adjustment System (DNS) domain name of your network connection may also cause this error. Update Windows servers are accessible through DNS servers configured for Internet access. If a local DNS server has changed for some reason, the Windows Update client isn't able to find and connect to the Windows Update server.

  I would like to know if refer to a Microsoft article to work around this problem by changing the settings default for a manually configured DNS server DNS (Domain Name System).

  I would say to you to follow the steps mentioned in the link below for the complete solution of the problem

  0x8024402C error code when you try to install updates on Microsoft Update or Windows Update Web sites

  http://support.Microsoft.com/kb/900936/en-us

  Windows Update error 8024402C

  http://Windows.Microsoft.com/en-us/Windows7/Windows-Update-error-8024402C

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.