WRV200/Quick VPN and dynamic DNS
Linksys supports States that I need to contact verizon DSL to get a public IP address and set up a "bridge connection" in the DSL modem. I would try even when using dynamic DNS. If someone is successful with this change I would appreciate some tips
To use the dynamic DNS on the WRV you will need a public IP address on the WRV and for what the modem needs to be filled. This brings you straight to where you already are.
Tags: Linksys Routers
Similar Questions
-
SSL VPN and Dynamic DNS - ddns on IOS
Hello
I am configuring a VPN SSL via SDM tunnel on a 877 router. The router gets the dynamic public IP address from the ISP, so I configured DDNS for remote access to the router. I would like to know if it is possible to configure the SSL VPN to support dynamic IP via SDM o CLI.
Concerning
Gerard
Looks like I fixed the problem using:
WebVPN gateway gateway_1
interface Dialer0 port 443 of intellectual property
SSL local trustpoint
development
However when the router restarts, it generates this error:
Incorrect ip address first configure the gateway IP address
No idea how to postpone orders for webvpn start until dialer0 Gets a dynamic IP address?
-
Internet connection sharing and dynamic dns.
Hi all.
Thank you for taking the time to read my message and respond. Much appreciated :-)
I have an old machine to windows xp with a usb key with an internet connection while I wait for my fiber :-)
I also have another piece of equipment connected via a crossover cable and they share internet and local traffic.
The other piece of equipment has a service that is running on what I can access locally, but I wish I could use around the web.
I have signed up for a dynamic dns account and have a host name.
I've assigned my public ip address for the host name, then im stuck. I tried several times and countless forums but I can't get my head around dynamic dns process. Can someone inform me?
the service runs on a particular port, and I know that I need to port forward, but I normally would in a router and I'm wundering is there a way to do it under windows?
Any help would be appreciated.
And I know diet teaspoon is not an option.
Thank you
HHi Haehjen,
You will need to open the ports in the security software installed on the computer for the task you want to perform.
Windows Firewall may block some programs to communicate on the Internet after you install Windows XP Service Pack 2
http://support.Microsoft.com/kb/842242
How can I turn on or turn off the firewall in Windows XP Service Pack 2 or later versions?
http://support.Microsoft.com/kb/283673
Distance issues, I would say that you post your question in the TechNet forums.
http://social.technet.Microsoft.com/forums/en-us/categories/
-
I need assistance with my WRVS4400N (its Firmware Version on: V1.1.03, I think that the more recent on this product) with VPN.
At one end of the IPSEC VPN is this router. three other ends are WRV210.
I noticed that if if I have a site that has an ISP who changes IP very frequently (in this example 2 site), the problem is that the WRVS4400N will know the new IP address on the summary page, but retain the old IP on the configuration page.
Here's what I mean.
(1) if I set up the following VPN will display.
N ° name State P2 Enc/Auth Local Group remote control Remote Gateway
1 place 192.168.1.0/24 BRANCH1 192.168.100.0/24 3DES/SHA-1 221.100.100.10
BRANCH2 2 place 192.168.2.0/24 192.168.100.0/24 3DES/SHA-1 221.100.100.20< notice="" this="" is="">
3 place 192.168.3.0/24 BRANCH3 192.168.100.0/24 3DES/SHA-1 221.100.100.30(2) if 2 PSI (short DHCP lease time) branch forced a change in intellectual property
N ° name State P2 Enc/Auth Local Group remote control Remote Gateway
1 place 192.168.1.0/24 BRANCH1 192.168.100.0/24 3DES/SHA-1 221.100.100.10
2 Down3DES/SHA-1 192.168.100.0/24 192.168.2.0/24 221.100.100.22 BRANCH2< new="" ip="" is="">
3 place 192.168.3.0/24 BRANCH3 192.168.100.0/24 3DES/SHA-1 221.100.100.30(3) what I'm doing is:
(3A) go to change Edit, Branch2, the remote gateway IP/resolved by the DNS to IP/IP, and I see
IP resolved by the DNS: branch2.dyndns.org---> IP address: 221.100.100.20 (note that it retains the old IP)
I change to the new IP 221.100.100.22 and the tunnel will go up
(3B) or simply reboot the router and the tunnel will go up.
It seems that the problem is a bug in the firmware, when I really need to do something is the ' ipconfig/flushdns' line on the box.
Is that what anyone has experienced the same problem?
======================================
-Main WRVS4400N router-
DDNS service provider: DynDNS.org
Host name: main100.dyndns.org
Internet IP address: 221.200.200.1
Status: enabledType of local security gateway: IP only
Local Security Gateway IP Address: 221.200.200.1 (this sample provide by my ISP)Local security group type: subnet
Local security IP address group: 192.168.100.0
Local security group of subnet: 255.255.255.0Remote security gateway type: IP only
The gateway security remote DNS IP resolved: branch1.dyndns.org (branch2.dyndns.org for the second, third branch3.dyndns.org)Security remote control unit Type: subnet
Security group remote IP address: 192.168.1.0 (on second 192.168.2.0, 192.168.3.0 third)
Group of security remote subnet: 255.255.255.0-Branch WRV210 router-
DDNS service provider: DynDNS.org
Host name: branch1.dyndns.org
IP Internet address: 221.100.100.10 (first sample; 221.100.100.20 second 221.100.100.30 on the third)
Status: enabledLocal security group type: subnet
Local group of Secure IP: 192.168.1.0 (on second 192.168.2.0, 192.168.3.0 third)
Security group local subnet: 255.255.255.0Remote secure group type: subnet
Remote secure group IP: 192.168.100.0
Group secure remote subnet 255.255.255.0Secure remote gateway type: COMPLETE domain name
Entry remote secure gateway: main100.dyndns.orgThis problem was solved when I upgraded to version 1.1.13.
-
See dekstops and dynamic DNS updates
In general, I always do an ipconfig/release on the VM parent to make sure that its IP address is not carried over to the clones. When creating, pool and virtual computers start, they are able to get an IP address and DNS name is registered. However, the new virtual machine has without the permission of its DNS record, so it cannot dynamically update its DNS record. I have to manully updated each DNS record, allowing each VMs computer complete object to its respective DNS record. Obviously, it is not well-suited. I did something wrong in the configuration or is this a problem with view 3? Thank you.
I see no reason for your question, but I don't have this problem because my XP SP3 virtual machines are their acquired DHCP quite happy with my DNS server addresses. Looking at permissions associated with a DNS record, virtual machine computer account has permissions specific, not hereditary, (write all properties, read permissions, all validated writes). They are in a non-persistent pool and I did not communicate the IP address before you close the image gold and taking the snapshot related clones are based on. Your master VM has been properly linked to your domain that I guess?
---
If you have found this device or any other answer useful please consider the use of buttons useful or Correct to award points.
-
External address of Mgmt - DHCP/Dynamic DNS
Hello
My client is looking to assign the "external Mgmt addresses' for their B series server blades (KVM) via DHCP and dynamic DNS instead of a statically defined pool.
Grateful if someone can confirm if this possible?
Regards, Paul
Hey Robinson,
How are you? IP to KVM management can only be assigned statically to the MMIC or be affected by an ip pool.
See the link below
Managament (UCS 2.1) Ip addresses
-
Fast WRV200 with VPN connection
I have a WRV200, the latest firmware 1.0.39, I used to be able to connect using Linksys VPN fast running. Nothing has changed on the router, and I tried the two latest versions of quick VPN software. The WRV200 is configured with an internal network of 192.135.xxx.xxx address. When I connect via the quick VPN, it goes through all the procedures of activation, and I know that I am communicating with the router. Happens to step network review, and I start to get the message across - remote gateway not responding do not, I want to wait. If I say yes, it doesn't connect, if I say no, it will stop. Please help - the only documentation I can find Cisco on this issue, is that the internal IP address is identical to the address that I am trying to connect - that is not. I connect from an internal ip address of 172.xxx.xxx.xxx. Thank you.
Good afternoon
It is a problem with traffic being blocked or altered PORT500. Try to run a scan of port of GRC.com (Shields UP) and see if the traffic is blocked. Be sure to plug directly into the local ISP (no router) connection and then disable the firewall to get a real test.
Here is the link to the program, you need to run.
If the test does not work for you, then I would recommend that you call the HWC to 866-606-1866 support, they can test at the hearing to see if the connection works at their end.
Have a nice day :)
-
remote VPN and vpn site to site vpn remote users unable to access the local network
As per below config remote vpn and vpn site to site vpn remote users unable to access the local network please suggest me a required config
The local 192.168.215.4 not able ping server IP this server connectivity remote vpn works fine but not able to ping to the local network vpn users.
ASA Version 8.2 (2)
!
host name
domain kunchevrolet
activate r8xwsBuKsSP7kABz encrypted password
r8xwsBuKsSP7kABz encrypted passwd
names of
!
interface Ethernet0/0
nameif outside
security-level 0
PPPoE client vpdn group dataone
IP address pppoe
!
interface Ethernet0/1
nameif inside
security-level 50
IP 192.168.215.2 255.255.255.0
!
interface Ethernet0/2
nameif Internet
security-level 0
IP address dhcp setroute
!
interface Ethernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
Shutdown
No nameif
no level of security
no ip address
management only
!
passive FTP mode
clock timezone IST 5 30
DNS server-group DefaultDNS
domain kunchevrolet
permit same-security-traffic intra-interface
object-group network GM-DC-VPN-Gateway
object-group, net-LAN
access extensive list ip 192.168.215.0 sptnl allow 255.255.255.0 192.168.2.0 255.255.255.0
192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0
tunnel of splitting allowed access list standard 192.168.215.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
MTU 1500 Internet
IP local pool VPN_Users 192.168.2.1 - 192.168.2.250 mask 255.255.255.0
ICMP unreachable rate-limit 1 burst-size 1
enable ASDM history
ARP timeout 14400
NAT-control
Global 1 interface (outside)
NAT (inside) 1 0.0.0.0 0.0.0.0
Route outside 0.0.0.0 0.0.0.0 59.90.214.1 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
the ssh LOCAL console AAA authentication
AAA authentication LOCAL telnet console
AAA authentication http LOCAL console
AAA authentication enable LOCAL console
LOCAL AAA authentication serial console
Enable http server
x.x.x.x 255.255.255.252 out http
http 192.168.215.0 255.255.255.252 inside
http 192.168.215.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Crypto-map dynamic dynmap 65500 transform-set RIGHT
card crypto 10 VPN ipsec-isakmp dynamic dynmap
card crypto VPN outside interface
card crypto 10 ASA-01 set peer 221.135.138.130
card crypto 10 ASA - 01 the transform-set RIGHT value
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 65535
preshared authentication
the Encryption
sha hash
Group 2
lifetime 28800
Telnet 192.168.215.0 255.255.255.0 inside
Telnet timeout 5
SSH 0.0.0.0 0.0.0.0 outdoors
SSH timeout 5
Console timeout 0
management-access inside
VPDN group dataone request dialout pppoe
VPDN group dataone localname bb4027654187_scdrid
VPDN group dataone ppp authentication chap
VPDN username bb4027654187_scdrid password * local store
interface for identifying DHCP-client Internet customer
dhcpd dns 218.248.255.141 218.248.245.1
!
dhcpd address 192.168.215.11 - 192.168.215.254 inside
dhcpd allow inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
Des-sha1 encryption SSL
WebVPN
allow outside
tunnel-group-list activate
internal kun group policy
kun group policy attributes
VPN - connections 8
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value split tunnel
kunchevrolet value by default-field
test P4ttSyrm33SV8TYp encrypted password username
username kunauto password bSHrKTGl8PUbvus / encrypted privilege 15
username kunauto attributes
Strategy Group-VPN-kun
Protocol-tunnel-VPN IPSec
tunnel-group vpngroup type remote access
tunnel-group vpngroup General attributes
address pool VPN_Users
Group Policy - by default-kun
tunnel-group vpngroup webvpn-attributes
the vpngroup group alias activation
vpngroup group tunnel ipsec-attributes
pre-shared key *.
type tunnel-group test remote access
tunnel-group x.x.x.x type ipsec-l2l
tunnel-group ipsec-attributes x.x.x.x
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
Review the ip options
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
inspect the icmp
!
global service-policy global_policy
context of prompt hostname
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:0d2497e1280e41ab3875e77c6b184cf8
: end
kunauto #.Hello
Looking at the configuration, there is an access list this nat exemption: -.
192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0
But it is not applied in the States of nat.
Send the following command to the nat exemption to apply: -.
NAT (inside) 0 access-list sheep
Kind regards
Dinesh Moudgil
P.S. Please mark this message as 'Responded' If you find this information useful so that it brings goodness to other users of the community
-
PIX-to-client VPN and how to reach on other interfaces systems
Hi all
I've implemented a Pix-to-Client VPN and it seems works ok.
As you can see, customer gets the same inside the class address (192.168.100.x) so I can reach across systems.
My questions are:
If I give different subnet pool addresses, how can 1 I still reach inside systems?
2 if I have other systems on these interfaces such dmz1 (192.168.10.0) dmz2 (192.168.20.0) how to get to these systems of the
even the client vpn access?
Concerning
Alberto Brivio
IP local pool vpnpool1 192.168.100.70 - 192.168.100.80
access-list 102 permit ip 192.168.100.0 255.255.255.0 192.168.100.0 255.255.255.0
NAT (inside) - 0 102 access list
Permitted connection ipsec sysopt
Crypto ipsec transform-set esp - esp-md5-hmac trmset1
Crypto-map dynamic map2 10 set transform-set trmset1
map map1 10 ipsec-isakmp crypto dynamic map2
map1 outside crypto map interface
ISAKMP allows outside
ISAKMP identity address
part of pre authentication ISAKMP policy 10
encryption of ISAKMP policy 10
ISAKMP policy 10 md5 hash
10 2 ISAKMP policy group
ISAKMP life duration strategy 10 86400
vpngroup address vpnpool1 pool test
vpngroup split tunnel 102 test
vpngroup test 1800 idle time
test vpngroup password *.
It is generally preferable to use another range of IP addresses. The PIX will know that the VPN Client uses that vary and route it properly whitch is not the case when you are using the same IP range as the inside interface.
To access another interface use the SHEEP (your ACL 102) access list which disables NAT between the VPN and the neworks to which you want to connect.
Example of config:
access-list allowed SHEEP Internalnet ISubnetMask VPN-pool 255.255.255.0 ip
access-list allowed SHEEP DMZnet DMZSubnetMask VPN-pool 255.255.255.0 ip
NAT (inside) 0 SHEEP
AAA-server local LOCAL Protocol
AAA authentication secure-http-client
Permitted connection ipsec sysopt
Crypto ipsec transform-set esp-3des esp-md5-hmac TRANS
Crypto-map dynamic outside_dyn_map 20 game of transformation-TRANS
card crypto 65535 REMOTE ipsec-isakmp dynamic outside_dyn_map
REMOTE client authentication card crypto LOCAL
interface card crypto remotely outside
ISAKMP allows outside
ISAKMP identity address
ISAKMP nat-traversal 20
part of pre authentication ISAKMP policy 10
ISAKMP policy 10 3des encryption
ISAKMP policy 10 md5 hash
10 2 ISAKMP policy group
ISAKMP life duration strategy 10 86400
IP pool local VPNPool x.y.z.1 - x.y.z.254
vpngroup VPNGroup address pool VPNPool
vpngroup VPNGroup dns-server dns1 dns2
vpngroup VPNGroup default-domain localdomain
vpngroup idle 1800 VPNGroup-time
vpngroup VPNGroup password grouppassword
username, password vpnclient vpnclient-password
sincerely
Patrick
-
How to establish a tunnel vpn ipsec using DNS with ASA 5505?
Hello
I m get a dynamic IP address public and what I m trying to do is establish a tunnnel remote vpn using IPSec, which I realize my provider but each time resets of sessions or ASA 5505 reset, I get a new public IP and I need to put the new IP address on the remote client, so I can establish the vpn...
How can I establish a vpn ipsec using DNS? For this scenario, the remote client vpn is a vpn phone, but it could be any vpn client.
Private private Public IP IP IP
PBX - Telephone (LAN) - ASA 5505-(Internet)-(router) Remote Site-(LAN) VPN-
Kind regards!
Ah ok I see, Yes in this case there is no that you can do other than request a static IP address from your ISP.
Kind regards.
PS: Don't forget to mark this question as answered. Thank you!
-
Stor.e cloud - dynamic DNS - remote control
Hello
I want to use my Stor.e cloud like a cloud. In my home network, all things will work.
Now, I wanted to set up the network and enable dynamic DNS.
I registered by freedns.afraid.org, but I only get a URL for the update.
I do not see what URL should I use the HDD to confiure.Can someone help me plese. Or someone make experiences with remote?
Thanksfor help!
I found the user manual for this device of Toshiba Stor E Cloud storage
Stor.e Cloud user manualPlease see page 41.
Here you can find information how to set up dynamic DNS using advanced settings -
R7500 Dynamic DNS - no ip - manage devices
Hello
I had set up dynamic DNS using no. - ip (NETGEAR supplier - "*.") mynetgear.com') on my router R7000, before.
Now, I changed to a R7500.
But my noip.com account still has the 'old' R7000 device under host / redirects-> manage devices.
And I can't seem to remove the R7000 and serial number. (and I don't have the R7000 no more).
The R7500 refused to apply the account settings for:
Service provider: NETGEAR
E-mail:
Password:
without any error message.
I missed something?
Thank you
Hello
I can't remove the R7000 go in my list of devices (or at least, I can't find a delete option).
BUT after removing the hostname of my old camera AND delete the full host name subsequently (on noip.com), I could re-register the R7500 with my host name. So ultimately it works again!
Noip.com, on the R7000 is more listed as acive device, but it seems that I can't delete the old of my list.
-
RVL200 - SSL VPN and firewall rules
Forgive my ignorance, but I have been immersed in the configuration of this device RVL200 to allow Remoting SSL VPN to a customer site, sight unseen. I have the basics of the VPN set up in config, but now move the firewall rules. We want to block all internal devices to access the Internet, but I don't want to cripple the remote clients that will be borrowed by blocking their return via the SSL VPN traffic. This leads to my questions:
(1) a rule of DENIAL of coverage for all traffic OUTBOUND will prevent the primary function of the VPN (to allow the administration away from machines on the local network)?
(2) if the answer to #1 is 'Yes', what ports/services do I need to open the side LAN?
(3) building # 2, configuring authorized outbound rules apply only for VPN clients, rather than all the hosts on LAN?
(4) as the default INCOMING traffic rule is to REFUSE EVERYTHING, do I have to create a rule to allow the VPN tunnel, or guess that in the configuration of the router?
Here are some other details:
- The LAN behind the RVL200 is also isolated LAN in a manufacturing environment
- All hosts on this network have a static IP address on a single subnet.
- The RVL200 has been configured with a static, public IP on the WAN/INTERNET side.
- DHCP has been disabled on the RVL200
- Authentication to the device will use a local database.
- There is no such thing as no DNS server on the local network
- The device upstream of the RVL200 is a modem using PPPoE DSL, and the device has been configured for this setting.
- Several database of local users accounts were created to facilitate the SSL VPN access.
I worked with other aspects of it for a long time, but limited experience with VPN and the associated firewall rules and zero with this family of aircraft. Any help will be greatly appreciated.
aponikikay, there is no port forwarding necessary to the function of the RVL200 SSL - VPN.
Topic 1. That is not proven. It shouldn't do. The router should automatically make sure that the SSL - VPN router service is functional and accessible.
Re 2. No transfer necessary. In addition, never before TCP/UDP port 47 or 50 for VPN functions. The TCP 1723 port is used for PPTP. UDP 500 is used for ISAKMP. You usually also to transmit TCP/UDP 4500 port for IPSec encapsulation.
Let's not port 47. ERM is an IP protocol that is used for virtual private networks. It is a TCP or UDP protocol. GRE has 47 IP protocol number. It has nothing to do with TCP or UDP port 47. TCP and UDP are completely different protocols of free WILL.
It goes the same for 50: ESP is the payload for IPSec tunnels. ESP is the Protocol IP 50. It has nothing to do with TCP or UDP port 50.
'Transfer' of the GRE is configured with PPTP passthrough option.
'Transfer' of the ESP is configured with IPSec passthrough option.
-
Dynamic DNS update of IPv4 addresses does not not in Windows 7
Several months ago, we noticed behaviors incompatible with Windows 7 clients and their entry in DNS Active Directory.
The main problem is that our Windows 7 clients only will be not systematically their IPv4 address in Active Directory DNS by using dynamic DNS (RFC2136)
Initial question:
- A handful of customers will register its IPv4 address, but it is a minority and most don't (this is the main question)
- We use the public IP address space.
- Customers have been constantly recording the IPv6 address for 6to4 in DNS card but not its IPv4 address.
We have disabled the 6to4 map by using Group Policy, because we do not use IPv6 and don't plan to use the 6to4 transition.
Secondary issue:
- Customers is no longer recording card 6to4 in DNS (good)
- Majority of customers do not yet record their (bad) IPv4 address.
What I've checked so far:
- Analysis using Wireshark:
- Most clients make no request for SOA record and therefore do not try to send dynamic DNS updates.
- Some customers get the AD zone SOA record and then send the DNS dynamic update to one of the DCs.
- I see nothing of clearly different on clients who send updates and those who are not.
- All the other AD related traffic, for example request/response for domain/ldap SRV record looks normal.
- Settings on the client:
- The IPv4 adapter "save addresses for this connection in DNS" checked.
- The primary DNS suffix is the same as our AD domain name.
- The AD domain name is a COMPLETE domain name.
- Use us group policy to apply the primary DNS suffix and some connection specific suffixes.
- Customers do everything they are supposed to; as access to shared resources, printers, etc. - just not update DNS.
I read all of the following, but I'm no further forward:
DNS of processes and Interactions
https://TechNet.Microsoft.com/en-us/library/dd197552 (v = ws.10) .aspx
Understanding dynamic update
https://TechNet.Microsoft.com/en-us/library/cc771255 (v = ws.11) .aspx
Does anyone have ideas/tools/scripts which may be able to progress my troubleshooting?
Darren.
This issue is beyond the scope of this site (for consumers) and to be sure, you get the best (and fastest) reply, we have to ask either on Technet (for IT Pro) or MSDN (for developers)
If you give us a link to the new thread we can point to some resources it -
Hello
I have a RV130 connected to the internet router/modem and I have configured the dynamic dns (No. - ip provider).
the problem is that the ip address that is returned to the ddns is the rv130 wan ip, not internet ip address.
If I use a machine on the network with the app to no - ip, it shows the internet ip in site no. - ip address, but since it is a customer that I can just ask her to keep a machine always on execution of the application.
is it possible to change the configuration on the rv130 or is this something I need to change the modem?
thnx
Hello
There is nothing you can or need to change on the router, it will report the IP address on the WAN connection.
Based on what you say, I think the problem is that the modem, the RV130 is connected to is acting as a router and providing a kind of IP address in the RV130 (10.x.x.x or 192.168.x.x or 172.16.x.x)
What you need to do is to contact the ISP and have them change the modem in Bridge mode so that the actual public IP goes directly into the WAN port on the RV130 and then the DDNS will show the correct address.
I hope this helps.
Maybe you are looking for
-
iOS 10 Bluetooth calling Infiniti G37
Hello Since the upgrade to the AT & T iPhone 7 (against his will - long story) with iOS 10, I have the unfortunate experience that Bluetooth is unusable to call my Infiniti G37 2013. Previously, accepting a call from iPhone 6 resulted in the micropho
-
Recovery of product without Norton AV?
Satellite A100-049, Vista Home Premium. Recently purchased this laptop works very well, except that I can't get rid of leftovers from Norton AV (quite a common problem, I understand), despite the execution of the program available on the Symantec sit
-
HP - 14 r-226TX: Disk Fragmentation
I have used avg antivirus and this is what makes that your hard drive is fragmented and it will slow down your pc and requires disk defragmentation. I don't know what it is, should I do it or not and if I do it really does speed up my pc and what sof
-
Error SQL Server 2012 trying to create a query?
I'm trying to run a statement on a particular table Select column but get an error and I can't understand it. Is attached a picture of the error
-
Cannot install windows 8.1, very frustrated :/
Hey, I have a HP Envy 4 1056-tx and it came with windows 7 Home premium that I currently use. Now. recently I tried to install windows 8.1 in it but it gives this message each time "Windows cannot be installed to this disk. The selected disk is a Tab