Internet connection sharing and dynamic dns.

Similar Questions

• Bluetooth network and Internet connection sharing problem

  I am putting in place a network via Bluetooth between two computers later with Toshiba Stack installed and to share the Internet connection with the second computer.

  On the computer of trees I put Internet connection sharing, and for this reason, it automatically assigns addresses TCP/IP for the Bluetooth Personal Area network (192.168.0.1).
  On computer 2, I put everything to get it automatically. Firewall (Kaspersky) disabled.

  When I connect 2 Bluetooth devices, everything looks fine, the 2nd automatically gets the IP address, I can ping both computers and Internet works also on the 2nd computer, for a few seconds! After that, it appears as the 2nd computer is disconnected from the network... what could be the problem?

  In the case of the observer under the System tab, I found information like these:
  2nd comp:
  The system has detected that the network \DEVICE\TCPIP_{E44D18EB-91F5-4 adapter has been connected to the network and launched a normal operation via the network card.

  The browser has forced an election on network \Device\NetBT_Tcpip_{E44D18EB-... because a master browser was stopped.

  and the 1st model also appears this:
  The system has detected that the network Bluetooth adapter... Area Network - Packet Scheduler Miniport has been disconnected from the network, and the network adapter configuration has been released. If the network adapter was not disconnected, this may indicate that it has malfunctioned. Please contact your vendor for updated drivers.

  In your case, I would look at the following Web site:
  http://APS.toshiba-tro.de/Bluetooth/redirect.php?page=pages/HOWTO.html
  It lists the following document:
  "Internet on PDA via PAN using Notepad as a gateway."
  In your case, the PDA is another laptop, but the procedure should be very similar.
  I would check the firewall settings later if it still does not work.

• Problem with Vista and XP computers Internet connection sharing.

  I have a host computer running Windows XP service pack 3, with an of Virgin Mobile Broadband2Go modem and a laptop computer with Vista. The host computer is connected to a Microsoft MN - 700 via a CAT5 network cable. The laptop is connected via a wireless connection. I'm sharing the Broadband2Go internet connection by using Internet connection sharing. I enabled sharing on the network, on the host computer connection. But the laptop does not connect to the internet. I can ping the host of the laptop, but cannot ping the laptop computer from the host. I have tried everything I can think of, to get the job of network. He worked, until Thursday. Thursday, there is some automatic updates installed on the host computer. They have been updated for security. I don't know if updates of security would have affected the network or not. All helkp would be appreciated.

  Thank you

  Oscar

  It is a facility that is complicated, because the host computer and the MN-700 can act as routers and DHCP servers, making it uncertain given the laptop its TCP/IP configuration.  Here are two ways to make it work:

  • Use the MN-700 as a router: connect the host computer to the "Modem" port of the MN-700.  To do this, interface LAN of the MN - 700 must have an IP address in a different subnet from the 192.168.0.x subnet that uses ICS.  The laptop will be able to ping on the host, but the host will not be able to ping from the laptop.

  or:

  • Use the MN-700 as a point of access only, not as a router: connect to the host computer to one of the MN-700 Ethernet ports and disable the DHCP server integrated of the MN-700.  Both computers should be able to ping each other.

  Boulder computer Maven
  Most Microsoft Valuable Professional

• Problem to create the Internet connection sharing between Windows XP and Windows Vista.

  Original title: Internet connection sharing between Windows XP and Windows Vista.

  Hello

  Recently, I plugged a laptop running Windows XP to a desktop computer running Windows Vista using a standard Ethernet cable with the intention of use sharing of Internet connection. The notebook contains a wireless connection that I've routed to the office via the cable said.  While the initial phase of installation went well (I was too lazy to do it manually, so I just used the Wizard "Set up a home or small business network" Windows XP,) I had to turn off the host computer to install a program. When I tried to set up ICS again, I couldn't connect to the Internet by using ICS. After this failure, I tried to configure the properties of TC/IPv4 (IP, gateway by default, etc.) manually, but I still couldn't run.  I am able to access the shared host PC and client files. It seems to me that some service essential to the proper functioning of the ICS may be disabled in some way, but it's just speculation, as I have no evidence of such a service. Help would be most appreciated.

  Thank you

  FG-man

  I tried this before using a laptop to share internet with my 360.  problem is there was Nat on the router, and it is in contradiction with the ics.

  Anyway long story short I did some research on the Internet and discovered that if you're behind a router ICS will be confllict with her, as ICS also does routing. a much better option is to "bridge the conections ' on the laptop.

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/hnw_bridge_install.mspx?mfr=true

  If you go this route, you need to set a static ip address for the office,

  Either that or if you want to continue using ICS put the laptop in the DMZ in the router may help, but it will be less secure.

  Hope that this helped good luck

• problem with Internet connection sharing, error: connection ad - hoc has "no internet access" on the cell phone of the customer

  Original title: problem with Internet connection sharing

  my laptop running on Windows Vista Home Premium SP2 (this one has access to the internet by using the dial-up modem and will to act as a sharer of internet connection or as a host) and the client computer runs on Windows 7 Starter

  in a first step, I try internet connection sharing, I've set up an ad hoc network and I just changed my setting modem dial-up on the sharing tab, of course what I change, it of 'Allow an other network users to connect through this computer internet connection' and choose the on Home Networking connection wireless network connection , then my mobile client to connect to a special that I created and portable client connected to the internet via ICS
  then the problem came when I restart my laptop. When I tried to use ICS once again, my customer laptop really takes a long time to connect, he continues saying 'identification' side host and client. and after that "identify" is complete, it says ad - hoc connection, I create has "no network".
  so, I'm a person answer in this forum
  ' Obtain an IP address automatically is the wrong setting on the Ethernet connection. "  To return to the sharing tab and unshare the wireless connection.  Close all windows network, and then open them and re - share the wireless connection.  Who must configure IPv4 for the Ethernet connection properties for:

  IP address: 192.168.0.1
  Subnet mask: 255.255.255.0
  Default gateway: no
  "DNS server: none.

  I put this on my laptop of the host, and and I put the IP address on my laptop customer in 192.168.0.2 with the same default gateway as my portable computer host IP

  and made some progress in this case, when I try to connect host and the client is no longer to 'identify' phase, immediately connected laptop both but my mobile client can not connect to the internet and displays "No Internet access" on the ad hoc network, I have create

  I tried a lot of things but always completed my mobile client can not connect to the internet and displays the message "no Internet access.

  What makes me confuse is first, I try to share the internet connection everything works like a charm, I set up an ad hoc network, and then change the setting on my modem dial-up so he can share the internet connection, and voila, computer laptop client connected to the internet. I change even not all IP settings

  But why after I restart my PC, this problem comes...

  someone knows how to help me with this problem?

  Hey, Mimbs,

  You can try the similar thread to the next with a possible solution:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-networking/no-Internet-access-in-the-client-machine-when/77312e09-4385-41FA-A420-0c42be58e4e3

  Also for reference:

  http://Windows.Microsoft.com/en-us/Windows7/networking-home-computers-running-different-versions-of-Windows

• Internet connection sharing does not work anymore

  I have used Windows Vista Home Premium for 2 years now on my laptop. Internet connection sharing enabled to connect to the internet via my wireless adapter and allowed me to share my internet connection through the ethernet port. He worked for more than a year. All of a sudden 4 months ago Windows Vista doesn't let me share the internet connection more. When I go to networking and sharing Center, click on "Manage network connections" and it shows that my "Wireless Network Connection" is always set to share. So after reading several forums, I clicked on wireless network connections and click right properties. Then I clicked on the sharing tab, to make sure that "Allow other network users to connect through this computer's Internet connection" has been verified and that it is. After that, Windows Vista will not always share the internet. Someone suggested that I double check the IP version 4 and 6 on the wireless and Ethernet connection were defined on IP addresses obtain automatically, and they are. The computer still will not share the internet connection! I even took the manufacturer in the view of portable and made sure my cable modem Simulator wasn't bad. I took it to a computer store and we checked the crossover cable. Everything is fine! What else can I try?

  Obtain an IP address automatically is the wrong setting on the Ethernet connection.  To return to the sharing tab and unshare the wireless connection.  Close all windows network, and then open them and re - share the wireless connection.  Who must configure IPv4 for the Ethernet connection properties for:

  IP address: 192.168.0.1
  Subnet mask: 255.255.255.0
  Default gateway: no
  DNS server: no
    
  Owner, Boulder computer Maven
  Most Microsoft Valuable Professional

• Internet connection sharing cannot be enabled.

  Greetings. I noticed a lot of posts about a similar situation, but I don't seem to find the answer that works for me. The skinny: using Windows 7. I connected to XBox live through ICS with my laptop. Hotel has wireless and I connected to it. Then, I followed the instructions and my wireless for sharing of the value. From there on, I wired XBox laptop w/ethernet cable and XBox settings manually configured as IP address, subnet, gateway, & DNS address mask. It was working fine the first day. During the next two days, connection was super slow... but it still worked. The problem does not seem to come from the hotel's Wi - Fi connection. It was the laptop for XBox it seemed. So I did some reading more and got more stupid than usual. I tried to 'Bridge' of the LAN and wireless connections to see if I could get better results. I'm not too good sense of course so I didn't know if it would work. There can be no. This is why I removed the two bridge connections and even removed the icon of "Bridge". I tried to go back to the original configuration that has worked and that's when I started getting the "connection sharing Internet can not be activated. A LAN connection is already configured with the IP address that is required for automatic IP addressing"message. So now, when I check the share my wireless, I have that message and it won't share. I'm lost! I tried "ipconfig \all. I tried "netsh winsock reset." Nothing seems to work. I don't know if I'm doing something of out of order which does not allow local network setting. I mean... what must be plugged in the ethernet cable, or even not at all, and when it is, that the parameters of the Xbox is? I even put the XBox failing to see network settings if I could start to this end. If it was not obvious, I'm still able to access the internet wireless and wired. This is something crazy and so far, none of my smart friends have been able to help! Thanks in advance for any of yours. As I said, I'm really not good with this stuff so if you have answers, please show idiot as I am a fool proof. See you soon!  Jim C

  Hello

  You can follow the Windows Help article below and check that ICS is set up correctly.

  Set up a shared Internet connection using ICS (Internet Connection Sharing)
  http://Windows.Microsoft.com/en-us/Windows7/set-up-a-shared-Internet-connection-using-ICS-Internet-connection-sharing

  If ICS is not configured correctly, then you must post back the result by running the following command.

  To do this:

  a. click the Start button.
  b. type cmd in the search box.
  (c) in the command prompt, you must type ' ipconfig/all ' and check the result.

  Take a screenshot of the command prompt and post.

  To take a screenshot, you can follow this link below.

  Use capture tool to capture screenshots
  http://Windows.Microsoft.com/en-us/Windows-Vista/use-Snipping-Tool-to-capture-screen-shots

  Thank you, and in what concerns:
  I. Suuresh Kumar - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  

• ICS: Internet connection sharing ERROR while allowing IP.

  Hi all

  My "Netgear" router gives the IP Address of the gateway 192.168.0.1 and my laptop is connected via a wireless connection. When I turn on my connection sharing wireless internet connection, windows xp tells me with the message below:

  "When Internet connection sharing is enabled, your LAN adapter will be on use the 192.168.0.1 IP address." Your computer may lose connectivity with other computers on your network. If these other computers have static IP addresses, you must set them to obtain their IP addresses automatically.
  "Are you sure you want to enable Internet connection sharing?"

  When I press 'Yes', it gives me an error:

  "An error occurred while Internet connection sharing was being enabled.

  Internet connection sharing cannot be enabled.
  A LAN connection is already configured with the IP address that is required for automatic IP addressing.

  My question is, if we can configure ICS service to activate other windows of the IP ADDRESS is required to apply?

  Thanks in advance for your help...

  I'm sorry, but ICS is completely inflexible and does not change its LAN IP address.

  The settings that you found are for something else: allowing unsolicited Internet connection requests to pass through the firewall on the ICS computer to a client computer.

  Change the address LAN IP of the router.  It is easy to do and will solve the problem.

• Failed to start service Windows Firewall/Internet Connection Sharing (ICS) on the local computer. Error 5: access is denied. »

  original title: error 5 access denied firewall

  Failed to start service Windows Firewall/Internet Connection Sharing (ICS) on the local computer. Error 5: access is denied. »

  Hi vipin sharmavg,.

  1. did you of recent changes on the computer?

  2. do you have security software installed on the computer?

  See the below Microsoft article and try the steps mentioned, check if it helps.

  You cannot start the Windows Firewall service in Windows XP SP2

  http://support.Microsoft.com/kb/920074

• Error: "Windows cannot start the windows firewall/internet connection sharing (ICS) service.

  On my Eee PC under XP Home edition tablet, I get the error "Windows cannot start the windows firewall/internet connection sharing (ICS) service" when I try to access my firewall. I also can't connect to my router Wireless Lan to go on the internet. This may be due to some viruses that have been deleted using Microsoft Security Essentials.But the problem persists. Could recharge SP2 solve this problem or am I condemned to reload the operating system?

  Hi jdmanel,

  NOTE: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following link. http://support.Microsoft.com/kb/322756

  Follow the steps in the article.

  You cannot start the Windows Firewall service in Windows XP SP2

  Troubleshooting settings of Windows Firewall in Windows XP Service Pack 2 for advanced users

  For reference:

  How to manually open ports in Internet Connection Firewall in Windows XP

• Why my internet connection sharing with my xbox 360 does not?

  my internet connection sharing use to work with my Xbox, but all of a sudden, it stops working, I then went on another computer which had xp (my other had 7) and it worked for a little started but still spoil later. I have another computer with xp and won't work at all with it. I think that I put everything in the right seat, and when I plug my 360 into my router it works but I want to be able to play in other rooms. I also tried to fill the connection on all 3 computers and it never worked.

  Hello

  See the following article:

  Use your computer to connect your Xbox 360 console to Xbox LIVE

  See also:

  Xbox 360 support

• Internet connection sharing (6) error during installation of nintendo wifi connector

  "sharing the internet connection (6) error" appears when I try to install a nintendo wi - fi connector (to connect between my wii and computer for netflix). I have high speed dial-up (canada), but apparently can use wi - fi connector to talk about the wii. with the first installation, it worked well enough to allow the wii. but the wii could not connect to netflix.
  the first time I had hung it, I ended up uninstalling and now when I try to reinstall it, this error message appears.
  When I got the wi - fi connector connected the first time, I did it with my antiviirus running program: the help site suggested to uninstall then reinstall the wifi band program. so this time (after you have uninstalled it), I disabled the antivirus, but now get the error message.
  I have a call in nintendo, but fear that it is a problem of microsoft xp.

  I don't have personal experience with this, but the title claims that it fixes your exact problem: Guide to fixing ' error (6) Internet connection sharing

• Internet connection shared with Xbox

  I need to restart my internet connection shared with my Xbox everytime I turn it on to connect to Xbox Live.  How can I keep this happen and more keep the Xbox all the time?

  Hi JohnnyBz,

  I suggest you send your query in Xbox live forum to get the best support that this is a dedicated forum for Xbox live. Link: http://forums.xbox.com/

  With regard to:

  Samhrutha G S - Microsoft technical support.

• Internet connection sharing everything just works. Problem really very annoying. Help.

  I have an Internet connection sharing situation. It worked perfectly until I got a little virus. Then, with the CORRECT settings, when I try to turn it on in Vista "allow the other network users to connect through this computer's Internet connection", I get an error message stating "unable to enable shared access. Error 0 x 80004005: unspecified error. "I checked and overchecked. The settings are OK, it's just my computer that has the problem, the other OS I installed (Windows 7) he shares perfectly. It is not material, it's just because of VISTA. What can I do? I searched on the Internet for 5 days and nothing. People seem to encounter this problem, but no answers, or nobody gives one any solution. Can I reinstall just the ICS service? Is this possible? To correct it, a key "reg", a patch, no matter WHAT? It is really really important. I removed all viruses from my computer. Internet works fine on my computer. What can I do? Please, please help me... Please, I beg you.

  Dear engineers,

  I have computer (A) where I use Vista Home edition and I have internet connected with the Ethernet adapter, and I have an another Computer (B) when I want to use internet. I did an adhoc network and connected two computers via wireless adapters, but computer B can not use internet b/c on computer A, I can't start Internet - ICS connection Service. whenever I try to start the service it gives following error;

  "Service ICS (ICS) on Local computer started and then stopped. Some services stop automatically if they are not in use by other services or programs"
  
  Can you please suggest a solution for this.
  Waiting for your response.

  Concerning

• Vista internet connection sharing configuration

  Please take note that I have already visited the URL for windows: http://Windows.Microsoft.com/en-us/Windows-Vista/using-ICS-Internet-connection-sharing

  I did the following:

  • Configured Internet connection service.  Service is set to automatic, running, recovery failures all the value zero seconds
  • Connection to the LAN is configured as 'shared '.

  BlackBerry Curve 8330 is connected the USB cable live and is considered 'removable disk' records can be seen

  The Blackberry a browser opera mini version 4.2 installed but cannot connect to the internet.  I ask for advice on how much of the configuration is proveable and how much more needs to be configured to connect to the internet. Concrete measures to solve the problem so that I can work on what remains to do research

  Hello

  I suggest you to send your application in Blackberry forum for better support.
  http://supportforums.BlackBerry.com/T5/General-support-forums/CT-p/GeneralSupportForums