Xfinity

Similar Questions

• Site XFINITY Speed Test, no results.

  I'm going on the XFINITY Speed Test site and try to get my test results, but start the speed Test does not appear?  I used this site many times in the past.

  Could be a cookie problem.

  If you use Safari...

  Go to the Safari menu bar, click Safari > Preferences then select the Privacy tab, then click on: Marches site Data , and then click remove all.

  Then quit and relaunch Safari and try again > http://speedtest.xfinity.com/

  I just tried the test and it works fine for me on Safari 10.0.

  If the deletion of cookies did not help, make sure that Flash is up to date.

  Open system preferences > Flash Player, click the updates tab, and then click: check now

• Is there a way to filter the Xfinity hotspots?

  I have Xfinity service, so these hotspots divert my phone and leave not data through.  If I'm near a hotspot when I try to access the Internet, the phone just turn, try to connect to the hotspot, but cannot.  I have to go and turn my wi - fi so that my phone to use only the data in place.  So I don't forget to activate the wi - fi on when I'm home that I * don't * use data.  Is there a way to tell just the phone to ignore all the Xfinity hotspots?

  If this is not the case, there should be.

  Thank you.

  It does not automatically try communicating with them, unless you told him at one point. The next time you close one, and it tries to connect, go to the settings WiFi and tell him to forget the network.

• How can I get my email xfinity?

  I don't know how to access my mail xfinity.

  Open a new tab in Firefox for iOS and go to http://m.xfinity.com - the first button should read this email. Follows to access your e-mail Xfinity.

• If I can do an Airport Extreme mobile network with a modem/router cable xfinity manufactured by Cisco?

  Can I create an Airport Extreme (current generation) network of roaming with a cable modem/router xfinity manufactured by Cisco (DPC3939 to be exact)?  The modem-router Cisco/Xfinity put into bridge mode?

  Can I create an Airport Extreme (current generation) network of roaming with a cable modem/router xfinity manufactured by Cisco (DPC3939 to be exact)?

  Yes, if the Airport Extreme will be connected to the Cisco DPC3939 back using wired Ethernet wired, permanent.

  The modem-router Cisco/Xfinity put into bridge mode?

  No. I you have done this, the Cisco/Xfinity device would only act as a simple modem... so it would not be a wireless service to all.

  A note of caution here... the support document you are referencing... Wi - Fi base stations: install and configure a roaming network (802.11 a/b/g/n)... use the examples that are long outdated does not follow with the versions present on a Mac AirPort Utility or iPhone/iPad.

  There are some good general information in the document.

• Could not load 'live' Xfinity TV Go in 40 Firefox (Windows 7)

  When you run Xfinity TV Go, after selecting "Live TV" and a program option, I get empty a screen with a message "Load video" and a bar of progression with 3 points. However, no content loads. I have let it run up to 30 minutes - same result. TV Go works fine with IE (haven't tried Chrome). Any suggestions, as a cache under Firefox options setting? I did find something that seems relevant. IE worked after that I changed a setting to video content runs automatically.

  Thank you.

  Hello

  I had a glance on this one, and from what I see, the service you are trying to use uses the Flash plugin. Following the information that you provided (thanks a lot!), looks like you are running the most up-to-date version.

  The Flash plugin has its own cache of the last pages you can clearly. Adobe have instructions as to do here. This can help allows you to view the video stream or live, you want to play.

  I hope that this solves the problem, but if not please come back here and we can look at another solution for you.

• How to turn the notifications in settings webmail xfinity?

  Windows 7, Xfinity.net webmail. Email notification has stopped working after it updated for Firefox 36.0.1. The red numbers that appear when new email has arrived no longer use FireFox. I manually check now. When I open Internet Explorer email notification works as before (very good). How can I enable notification back on, red number so when the email arrives I will be informed without having to manually check from time to time.

  Blacklion, looks like you are using a toolbar that alerts you when you have a new email. Please consider reinstalling the toolbar to deliver notifications. Or if it's for a specific site, check the notifications for the site permissions:

  Right-click on the page and click on 'View Page Info' in the opening menu. This opens a window with a "Permissions" tab I have this, scroll down to everything down until you see "View Notifications" that entry from the third to the last. Restore the default value, either just select "Block".

• Comcast and xfinity

  I'm trying to connect my TV to start provider to watch something on my apple (newish) TV.  Why I find each provider on the drop-down list EXCEPT Xfinity/Comcast?  My big cable operator is not enough?

  Looks like your cable provider is not large enough in terms of not generous enough. He may not want to allow you to access the programming on the ATV. After all, he will rent you a box to do this. Cable operators that allow mobile access, but not the ATV access are relatively frequent.

• Xfinity toolbar enabled but does not appear on the screen

  My Xfinity toolbar is enabled but does not appear on the screen. Tried to turn it off, remove it and add it back, but no luck. There is a space in which it above my Norton toolbar but it's only this - space. How can I make it reappear?

  Problem has been resolved by downloading a new version of the Comcast toolbar. They use to automatically update this bar tools, but for some reason stopped mines updated. But problem is now solved by this new version, the toolbar is now visible on the screen.

• How to hide xfinity wifi because I use TC

  Hello I have a dual band xfinity router connected to my TC via ethernet.

  How can I hide my other two network served by xfinity and just use my TC?

  You contact Xfinity support and ask them to provide you with instructions to turn off the wireless router Xfinity.

  As a general rule, this means that typing in the default IP of the router Xfinity in your browser... something like 192.168.0.1 (example only). .. .and by entering your username and password.  That will be bring up a list of the parameters of the router which can can be adapted.

  Search wireless page, or a tab and then find the option to disable the wireless service.

• Network: 2 routers Apple broadcasting separate wireless networks; one (Xfinity/Comcast) cable modem

  Hello community!  Need help, I want to use two routers to establish two separate wireless networks on a cable modem connection.  I searched for my answer and see some other threads on this topic, but all are either a bit too technical for me, are incomplete on the answers to my questions - and all seem to be locked.  I have also searched YouTube and only see videos to extend a network with two routers - not my goal.  So here is a long, but a detailed post on what I need someone help with - thank you very much in advance if anyone can all small-not me-I hope it will be useful to others in the future.

  The program installation/hardware: I have internet Comcast/Xfinity that runs to a Motorola surfboard cable modem (SB6141).  I also have two routers apple - a Time Capsule from Apple AirPort (to end 2013) and a new (2016) AirPort Extreme.

  Purpose: This is what I need--I need two separate wireless networks.  Before going further, by using the guest account and 5 GHz of a single router isn't an option for me.  I need to have both wireless networks separate (one of each router), do not talk to each other, or allow access between the two - the only is that they share the Comcast internet gateway.

  My plan is to have the cable modem Surfboard connect to airport Time Capsule, which will then connect to AirPort Extreme (even if it could be reverse - no difference, except that the data that I show below comes from the time Capsule, which is currently connected to the modem cable).

  To read the previous discussions, it seems that the starting point would be: modem router #1 Ethernet WAN, then a router cable #1 LAN Ethernet to the Router #2.

  First issue of clarification - the connecting cable should go to the Ethernet WAN port on the Router #2 or a LAN Ethernet port?

  Now that the first easy question is the road, I need help to configure two routers connected to allow two separate networks.  A lot of discussions about the positions of static IP addresses, cascade, etc..  I need specific help with AirPort Utility on what to change on what router.  It seems obvious that the settings under the 'Internet' and 'Network' tabs are those who need to set - the 'wireless' tabs simply treats the name of the wireless network and settings - these, at least I can understand!

  I'll organise this tabbed - here go us.

  First of all, the "Internet" tab/window Airport utility. Here are the options:

  Connect using: Router #1 has currently DHCP (which I think is OK?) What should it be set to Router #2?

  This tab lists also the current address in IPv4, the (255.255.254.0) subnet mask and the router address.

  It has grayed out information in the boxes for the DNS servers; Name of domain and DNS IPv6 servers.  At the bottom of the window, there is an IPv6 Internet WAN address listed.

  If I click on the "Internet Options" button at the bottom of the window, it takes me to the 'Internet Options' window. Here, there are various IPv6 information - it seems that I can choose the configuration of IPv6 and the IPv6 mode using the drop down boxes/selections were also chosen.  There is also a checkbox 'Enable IPv6 connection sharing'. Are the current settings for these for Router #1: configure IPv6: automatically; IPv6 mode: Native; and check/yes to enable sharing of IPv6.

  Next up, the 'Network' tab utility AirPort/window.

  Here, there is a drop-down menu "Router Mode", a DHCP range listed, and the ability to add or remove reservations DHCP and Port settings.  The DHCP range listed for Router #1 is 10.0.1.2 to 10.0.1.200.  There is currently no reserves DHCP or specified Port settings.  Finally, there is a checkbox to the bottom to "Activate the access control" - it is not currently checked/enabled.

  If I click on the 'Network Options' button at the bottom of the window, it takes me to the "Networking Options" window Here I have areas of entry to specify the DHCP lease duration, can specify the DHCP IPv4 range, as well as part of the extended DHCP IPv4 comments.  There are checkboxes: enable NAT Port Mapping Protocol. Select the host by default (with input if selected text box); Enable the IGMP Snooping; Block incoming IPv6 connections; Allow the Teredo Tunnels; and allow inbound IPSec authentication.

  For this window, here is the current settings on the Router #1:

  DHCP lease is 1 day; Beach DHCP IPv6 is 10.1.2 to 200; Hosts IPv4 DHCP Range is 172.16.42.2 to 200.  The following check boxes are enabled/checked: enable NAT Port Mapping Protocol. Block incoming IPv6 connections; And allow inbound IPSec authentication.

  Who can help me? What parameters, if all do I need to change the #1 router?  How to set up router #2 to make a second wireless network?

  Purpose: This is what I need--I need two separate wireless networks.  Before going further, by using the guest account and 5 GHz of a single router isn't an option for me.  I need to have both wireless networks separate (one of each router), do not talk to each other, or allow access between the two - the only is that they share the Comcast internet gateway.

  What you really need is a combination router / Ethernet switches that s supports VLANdedicated. Given that Apple routers do not, at best, you can potentially get the results that you are looking for, but at a performance cost. In other words, you can have two separate WiFi networks where clients connected to a network can not 'see' those related to another and both routers will always provide access to the Internet through Comcast modem. Note: Arris / Motorola SB6141 isn't a gateway device. Instead, it's a simple modem. A gateway is a router modem combination.

  To do this, should do the following:

  • The Time Capsule (TC) would need to be directly connected to the modem using an Ethernet cable. This base station would remain in its default configuration of the router. In other words, the router Mode (in AirPort Utility) would establish: DHCP and NAT.
  • AirPort Extreme would be directly linked to TB by Ethernet. The cable must be connected to one of the LAN ports on the TC on the WAN port to the extreme. It must also be configured as a router. However, there are differences in the extreme:
    • Use a different name to the Wi - Fi network.
    • Use another range of IP DHCP address. By default, Apple base stations use IP addresses in the 10.0.x.x range. I suggest that you set the base station of the second on 192.168.x.x range.

  There is a major drawback with this configuration. The second base station will be in a State of "Double NAT". Although this "separating" the two networks on different subnets, this condition is not very effective and connected to this network of customers will get lower throughput performance. There is no way around it and it is not recommended.

  First of all, the "Internet" tab/window Airport utility. Here are the options:

  Connect using: Router #1 has currently DHCP (which I think is OK?) What should it be set to Router #2?

  The two should be: DHCP.

  This tab lists also the current address in IPv4, the (255.255.254.0) subnet mask and the router address.

  These leave it as what. The TC is information of IP address of the modem. The extreme, he'll get the TC.

  It has grayed out information in the boxes for the DNS servers; Name of domain and DNS IPv6 servers.  At the bottom of the window, there is an IPv6 Internet WAN address listed.

  These leave it as what.

  If I click on the "Internet Options" button at the bottom of the window, it takes me to the 'Internet Options' window. Here, there are various IPv6 information - it seems that I can choose the configuration of IPv6 and the IPv6 mode using the drop down boxes/selections were also chosen.  There is also a checkbox 'Enable IPv6 connection sharing'. Are the current settings for these for Router #1: configure IPv6: automatically; IPv6 mode: Native; and check/yes to enable sharing of IPv6.

  Unless your ISP provides your IPv6 service, change the IPv6 configuration option to: 'Link-local only' on two base stations.

  Here, there is a drop-down menu "Router Mode", a DHCP range listed, and the ability to add or remove reservations DHCP and Port settings.  The DHCP range listed for Router #1 is 10.0.1.2 to 10.0.1.200.  There is currently no reserves DHCP or specified Port settings.  Finally, there is a checkbox to the bottom to "Activate the access control" - it is not currently checked/enabled.

  Router mode should be: DHCP and NAT to two base stations. Ignore the DHCP reservations and Port settings for now. Let the current DHCP range for the TC. Change the DHCP range for extreme for: 192.168.1.2 a.200. At this point do not access control for each base station.

  Since you seem to need the step by step instructions or need help to understand the different terms networking, I highly recommend that you help you to become familiar with networking, specifically on Apple systems. I suggest you consider taking the e-Book to the next control: take control of your Wi - Fi Applehttps://www.takecontrolbooks.com/apple-wifi network

• Having just downloaded Firefox, how can I get Comcast Xfinity?

  When I click on the Firefox icon, I want to connect to Comcast Xfinity. All I get now is Firefox home page.

  Follow these steps:

  • Upgrade to Firefox 29 Update Firefox to the latest version
  • Change your home page How to set the home page

• I just changed my internet provider to comcast/xfinity and I can't get rid of the xfinity homepage, what should I do?

  Although I've done XFINITY my home page, it is here and I can't get rid of it.

  Hello pineconewrangler, please install the addon reset search - he'll be back most common customizations as the homepage in firefox by default: https://addons.mozilla.org/firefox/addon/searchreset/

  or manually set any homepage of your choice: How to set the home page

• My email Xfinity does not appear correctly.

  I send Xfinity/Comcast. I've been for years on Firefox access xfinity.com.
  The e-mail screen now has a shadow/double letters. I can't click on and read all e-mail, but it is not correctly displayed in the Inbox.
  I contacted Xfinity and they asked me if I was using the most updated version of Firefox (I am) and then they had try me it in Explorer, which I did and it worked - but I prefer to use Firefox.
  Can you help me?

  Hello

  Many issues of the site can be caused by corrupted cookies or cache. To try to solve these problems, the first step is to clear cookies and cache.
  Note: This will be you temporarily disconnect all sites, you're connected to.
  To clear the cache and cookies to do the following:

  1. Go to Firefox > history > clear recent history or (if no Firefox button is displayed) go to tools > clear recent history.
  2. Under "Time range to clear", select "all".
  3. Now, click the arrow next to details to toggle the active details list.
  4. In the list of details, see the Cache and Cookies and uncheck everything.
  5. Now click the clear now button.

  More information can be found in article to clear your cache, history, and other personal information in Firefox .

  This solve your problems? Please report to us!

  Thank you.

• 9.3.2 and xfinity tv remote iOS app

  My Xfinity TV Remote App had several channels deleted after that I installed on my iPhone iOS 9.3.2 6 +. Comcast told me they had reset my account and I should delete the app and download a new one. But I can not download a new application, it starts downloading, but he returned to the cloud with the arrow icon to the bottom.

  Do a forced reboot - after all open applications using the app Chooser - invoked by fast double pressing the home button and drag upwards on each app until it disappears from the screen.

  Meet the sleep/wake and home buttons down until you see the logo  - then release and allow normal start upward