Y at - it a wireless adapter included in Satellite A60-662?

Similar Questions

• How to fix his jerky in PA3455U Toshiba bluetooth wireless adapter?

  I have Toshiba bluetooth wireless adapter PA3455U with Toshiba bluetooth stack v 8.0.0.12Tsoftware on Windows 7. When I use it in the A2DP profile I get his jerky.
  Tell me please how to fix this?

  Have you checked specification for this old piece of hardware, including system requirements?

• Satellite 5200 903 does not detect the wireless adapter

  Hello everyone,
  I wonder if anyone can switch me to it...
  Since I reinstalled the operating system (my XP pro SP2) PC seems not detecting don't nor the wireless adapter in the device under network adapter Manager.
  Also the light of the flexibility wireless no longer not.
  I also have problems to access the BIOS to check if the card is detected there, have not a Toshiba HW setup in Control Panel as described in the manual.
  Any suggestions?

  Hello Juliana

  The question is how did you install the operating system? If you use the restore CD to install all tools including Toshiba HW setup. If the unit is pre-installed with the Microsoft Windows XP Home edition CD, you must install all the stuff of Toshiba late.

  Just a little explanation about the wireless network card. Basically, if the wireless switch indicator turns not on s clearly indicate on hardware problem. I guess that the wireless card is faulty. Also check if the card is listed in the Device Manager.

  If you want to enter the BIOS settings pres ESC key at the boot routine and keep it down for a few seconds.

  Good bye

• Belkins wireless adapter recognizes not all wifi networks

  I have a Belkins wireless adapter for my pc and try to connect to a wireless network. My adapter recognizes not all wifi networks and I know that there is on the functioning of the House. How can I fix it?

  Laptop?  If you know that there is a wireless network in your home because the other computers are connected to him, the most likely cause is that the wireless adapter is disabled (a physical switch or a combination of keys Fn + Fkey).

  For additional help, please indicate the make and model of your computer (and your wireless adapter, if it is not integrated), as well as the version of Windows you have, including the service pack.

• Why my Intel wireless adapter is disconnected and does not restore until I restart the computer?

  Very randomly while I'm connected my computer won't go to any link and said I have no connection. I then try to solve the problem and it says to turn on my wireless adapter, but button is pressed and the light is on, so I turn it works without success. Then he tells me to check my router or a modem that always works so my ISP is not the problem. When this occurs, the computer does not have network connections, and has a red x beside the bars wireless not saying no connectivity, even give me the possibility to see the available wireless networks. The problem will persist until the computer is restarted, or the windows Explorer is restarted.

  Any ideas? Thank you.

  Pavilion dv6-3225dx
  Windows 7 Ultimate House
  Intel i3 M 350
  XY980UA #ABA

  Hello:

  The latest driver for your WIRELESS Intel network card is v 13.5.0 from 04/03/11.

  If this is the driver you have, then this is the most recent.

  If this isn't the case, you can give it a try, since you have nothing to lose. You shouldn't have to put up with unstable connections. I hope that the last version of driver if you are not running currently, solve your connection problems.

  I have included two versions of ILO since you listed only you had W7...

  W7 32-bit:

  http://Downloadcenter.Intel.com/Detail_Desc.aspx?AGR=Y&DwnldID=19855&ProdId=3199&lang=eng&OSVersion=Windows%207%2c%2032-bit * & DownloadType = software % 20Applications

  W7 64-bit:

  http://Downloadcenter.Intel.com/Detail_Desc.aspx?AGR=Y&DwnldID=19856&ProdId=3199&lang=eng&OSVersion=Windows%207%2c%2064-bit * & DownloadType = software % 20Applications

  Paul

• WIRELESS ADAPTER WILL NOT WORK UNLESS THE WIRED CONNECTION IS PRESENT

  PROBLEM: RECENTLY SPEND YOUR DESKTOP OF WIN - XP TO WIN 7 32 BIT AND MY HP LAP TOP VISTA 32, WINDOWS 7, 64 BIT.

  WIRELESS LAPTOP ADAPTER, NOT REARRANGE ITSELF TO USE A WIRELESS NETWORK

  CONNECTION. THE ROUTER AND WIRELESS ADAPTER HAVE THE CORRECT INFORMATION CONFIGURATION AND WORK WELL USING THE WIRED NETWORK. WHEN I MOVE THE NIC WIRELESS WI - FI FAILS.

  INFO WIRELESS ROUTER:

  LINKSYS BRAND: WRT300N V1.1
  BASIC WIRELESS SETTINGS: NETWORK RADIO BAND = AUTO, CHANNEL = MIXED MODE = AUTO, SSID = ACTIVE.
  WIRELESS SECURITY = WPA PERSONAL WITH TKIP ENCRYPTION

  WIRELESS ADAPTER, INTEL (R) WIRELESS WIFI LINK 4965AGN

  HP Pavilion DV 9700, WIN 7 64 bit update for Win Vista 32, NVidia Ge Force 8600 m GS graphic card, Win 7 64 bit.

  WHEN I CLICK ON THE ICON TO ACCESS INTERNET AND CLICK ON THE NETWORK TO CONNECT, THE WINDOWS NETWORK DIAGNOSTIC DIALOGUE BOX SHOWS CONNECTED, BUT FAILS TO COMPLETELY MAKE THE CONNECTION. WATCH THEN RESOLVE THE PROBLEMS, WHICH FAILS AND FINALLY TO INVESTIGATE THE PROBLEMS OF ROUTER OR ACCESS POINT...

  OTHER PEOPLE HAVE THIS PROBLEM, WHEN THEY SWITCH TO WIN 7. BUT THERE WAS NO MIRACLE DOCUMENTED THAT I CAN FIND ON THE WEB. IN THE OTHER FORUMS DISCUSS ISSUES RELATED TO THIS PROBLEM CONGREGATE, THEY PROVIDE NO BUGS. I NEED HELP TO SET UP MY WIRELESS NETWORK ADAPTER TO THE RECONFIGURATION OF THE WIRELESS NETWORK.

  Thank you all who responded and have tried to help me. Before posting, I tried most of the mentioned patches, including upgrading my firmware of the router. In addition, I went to Device Manager and scanned for changes and checked the properties under the Advanced tab of the Wifi link adapter. I tried the update driver and deactivation and activation of the device. None of this has worked.

  Finally, I uninstalled and then reinstalled the Wifi card. It worked. I guess the driver software became corrupt and data of the register of the device had probably need re - install, this is what worked. This seems to happen when upgrading Windows operating systems prior to WIN 7 and later people lose their wifi connection. Then this problem develops.

  It worked for me. I hope this works for others with the same problem.

  Once again I thank you all.

• -SOLVED! -PCI or USB wireless adapter is disabled and will not activate on Windows 7

  The solution: uninstall ZoneAlarm!

  I spent 3 days and 3 different cards, trying to solve this problem. First of all, I bought a Netgear PCI wireless adapter. Installed according to the instructions. Device Manager showed the adapter works properly but turned off and nothing I tried would enable the adapter.

  NETGEAR has taken over to the store and buy a Linksys PCI wireless adapter. Exactly the same problem. Device Manager, said the adapter worked correctly, but turned off and would not turn on.

  So I called Linksys support and paid them only for the remote service and they couldn't get it to work either (of course to return money). They suggest is to contact Microsoft technical support or buy the USB version.

  I went and picked up the USB (WUSB600-N v.2) version today and guess what? Exactly the same problem. Device Manager showed the device works correctly, but turned off and would not turn on. After talking to a few other technicians in addition to myself, we agreed that the only other option was to reinstall windows. But just before I decided to do, I checked one last time to Google and came across a post in the forums of Vista by someone who had the same exact problem, uninstalled ZoneAlarm and then worked their wireless adapter.

  Well, I decided to try that before reinstalling windows. As soon as I uninstalled ZoneAlarm and the computer restarts, the adapter has been activated and automatically found my network! This means that ZoneAlarm control network on the computer and for some reason cards some not allowing a wireless adapter is enabled.

  Then I tried to re-setup of ZoneAlarm. After that I have re-installed, my wireless adapter became instantly disabled and would not turn on again. So I uninstalled ZoneAlarm at all times. My router has SPI and NAT firewall on top of the Windows Firewall, so I need anyway ZA.

  If you have ZoneAlarm, get rid of it. If you still experience the problem of your card activating Wireless does not and have ZoneAlarm, try to uninstall any firewall software 3rd - party that you have already installed (not the Windows Firewall).

  I was really frustrated after spending 3 days with 3 different adapters and many trips to stores using the adapters and buy different cards. I'm glad I found this post on the forums of Vista, so the credit goes to the one who made this post.

  On a side note, after I installed the drivers from the CD and Linksys site, Windows update has shown there is an updated driver on the site of Ralink which I installed it and so far no problem. My WUSB600-N automatically connected to the strip of the 5 GHz on my router dual band and speeds are ultra fast and signal is strong in a completely different room.

  Hope this information helps others finally solve this problem.

  See you soon,.

  Matt

  64-bit, but it should work on either. ZoneAlarm includes network connections and was not what allows the adapter to be activated. Even close ZoneAlarm does not work either. ZoneAlarm must be uninstalled from the card must be activated.

  Vista drivers work fine with this adapter. Then a Windows Update is the updated drivers for Ralink which also work very well.

  If you have properly installed the drivers and display device manager the device works correctly, but disabled, and then uninstall any firewall/antivirus 3 rd-party should do the trick.

  I am a tech, more I consulted other technicians as well as paid for technical support of Linksys and nobody could understand this problem and it's no wonder. Who would have thought that ZoneAlarm or any 3rd part antivirus/firewall software would take complete control over network connections and not to allow a new network adapters must be installed correctly.

  If anyone needs any help other than that, feel free to ask.

• Envy 14-3010NR wireless adapter issues, this is a strange...

  Hello, I have a 3010NR Envy14 spectrum with Intel Centrino Advanced N6230 wireless adapter. Driver is 15.9.0.5 dated 16/06/13 dated. I've updated the operating system first to W8 and then to W8.1, since I had problems with the wireless, I had to work at some point after the update of the bios F.06, then when I started the other day, wireless.

  I have search in the diagnosis of F2 and it says that the adapter is not installed, when I do a test of component... However when I go to Device Manager / network adapters / click on display / hidden devices, this is, when I look in the properties, he said ""currently this hardware device is not connected to the computer"(code45)". "" To solve this problem reconnect you this hardware device to the computer.

  I also have the same problem with the wireless button on the keyboard that I see a lot of people, when I press on it now it switches airplane mode on and outside, where it is used to turn the WiFi on and off... It's always a white light, the orange light that lights up when wi/fi was off is now gone...

  Notice to fans, it's really weird... Thanks in advance

  Hey jagnewr,

  Thank you for all the information in your message. For the error code that you get in the Device Manager, it means that the device is connected is no longer http://bit.ly/18I67As.

  I've included the manual 'Guide to Service and Maintenance HP ENVY14 SPECTRUM'. Please open page 52 and follow the steps to remove the WLAN module. Remove and reset the module.

  If you are still not able to connect, and the error code 45 is still present it most likely that the wireless card no longer works.

  Good luck!

• HP Pavilion G6-1215ex: could not find "Wireless adapter" in my device manager.

  Hello.

  I recently formatted my HP Gseries laptop and reinstalled all the drivers. Towards the end of it, I couldn't find my adapter wireless listed in my device manager. I can connect to the internet via a connection fixed but the Wireless does not exist. When I try to install the wireless driver, the Setup program cannot detect the wireless network card.  I tried the following, which none has seemed to work:

  Turned on the wireless devices. Bluetooth works. Wi - Fi nope.

  Checked for possible compatibility problems drivers.

  There was something a little "unrecognized network controller" in the "other devices" category, which I assume is my wireless adapter. Therefore, I have included the hardware below id if this would be of any help. Please help me find the appropriate patches for my problem.

  PCI\VEN_14E4 & DEV_4727 & SUBSYS_1795103C & REV_01

  PCI\VEN_14E4 & DEV_4727 & SUBSYS_1795103C

  PCI\VEN_14E4 & DEV_4727 & CC_028000

  PCI\VEN_14E4 & DEV_4727 & CC_0280

  Thank you in advance.

  Hello

  Please try:

  Broadcom Wireless LAN Driver for Microsoft Windows:

  http://ftp.HP.com/pub/SoftPaq/sp57501-58000/sp57965.exe

  Kind regards.

• RALink 802.11n Wireless Adapter - connects at startup but the dsiconnects after a few minutes

  Hello

  I have a HP Pavillion DV6-3125SA and just reinstalled Windows 7 Home Prem after installing a new hard drive. Initially everything (including the wireless adapter) had been working perfectly, and then after the last round of updates (as you know that get you about 1 million of updates on the re - install) my wireless adapter started to misbehave. He started sporadically disconnect and reconnect, but now it gets disconnected and remains disconnected. It still works fine at startup. I checked that the driver software is updated, more I also uninstalled and let it automatically re - install. An interesting point to note, is that when I linked to go in Device Manager to disable (and re-enable), Device Manager freezes and unresponsive.

  Someone at - it had a similar problem or know a solution?

  Thanks for your help.

  Megan

  Its a cell phone, right?

  Run windows Update >... settings disable the updates recommended leaving ONLY the important updates for automatic installation.

  Visit the HP support, specific to your model, and then reinstall the chipset and wireless driver

  See if that helps

• How to get a USB 2.0 wireless adapter to work on Win7 Ultimate 64-bit?

  Details:

  ASUS P8Z77 - V motherboard w/Intel Core i7 3.5 Ghz 3770 K LK
  16 GB OF RAM
  HWUN4 USB 2.0 wireless adapter b/g/n w/Realtek chipset Hawking RTL8192CU
  Windows 7 Ultimate 64-bit fully updated to include SP1
  It is the second USB card who refuses to work on this platform, the first being something Rosewill which also uses a Realtek chip.
  I checked that the drivers for my MB are up-to-date, verified that I have later Hawking, tried drivers directly from Realtek drivers for the chip and assured that I installed the latest Intel MEI driver package for my motherboard. I went on the USB settings in the BIOS, but I'm not exactly fluent in what the options really are or do. I went through all of this also try to get the Rosewill unit to work several months past, as well, but without success with a device. It is postulated that the Hawking unit is actually Edimax, although I can't find any similar product on the site in order to try the drivers for. I also completely turned off my firewall ZoneAlarm and Avast! antivirus during installation and configuration, for the same results each time. The results does not same are achieved regardless of USB 2.0 ports 10 or if I connect to the adapter for.
  With this Hawking and the previous Rosewill adapter, drivers seem to installs successfully, such properties as displayed in the Device Manager say "this device is working properly", but they do not find a wireless signal. Simply says Windows Network Diagnostics adapter is "problems" and suggests that drivers can be a problem and always indicates that the latest drivers are already installed every time I have send the update to the latest drivers on my hard drive.
  I can come to only three possible conclusions:

  (1) Windows 7 Ultimate 64 - bit is unable to use USB 2.0 wireless network cards.

  (2) Windows 7 Ultimate 64 - bit is unable to use USB adapters based on the Realtek chips.

  (3) my motherboard lacks the correct BIOS settings to fully activate USB wireless.
  I have several other USB 2.0 devices that all work fine on this platform, including cameras, USB keys, external drive docks, mice, keyboards, phones, and others. I googled the days and found nothing to convince me the problem with my motherboard, I can't find anything specific on Win7x64 being a problem with this. Comments on NewEgg and other sites indicate people successfully use wireless adapters USB with Win7x64 and even on the same motherboard, I use, so I have to assume that I have either overlooked something or not yet found appropriate hardware and/or software settings.
  With this post being half-rant and half-cry for help, I will respectfully ask for suggestions on how to solve this maddening problem.

  «I don't mention it in my first post, certainly, but these devices have very certainly works wonders on a laptop with Win7x64 and a desktop computer with WinXPx32 installed.»

  So your previous conclusions are wrong, because they contradict what you are saying now.

  I can come to only three possible conclusions:
  (1) Windows 7 Ultimate 64 - bit is unable to use USB 2.0 wireless network cards.
  (2) Windows 7 Ultimate 64 - bit is unable to use USB adapters based on the Realtek chips.
  (3) my motherboard lacks the correct BIOS settings to fully activate USB wireless.
   
  I wanted to know if the adapter STILL works, not its past history. I have a D-Link WDA 2320 worked in another PC perhaps a year previously, but now it shows in the configuration, and that's as much as I can get with it. A few years ago I had a computer that did not like any wireless device, either PCI or USB and finished by hard wiring it which was very annoying.
   
  OK, back to your...
   
  Go to Device Manager and uninstall the device.
  Then set Device Manager to show hidden devices.
  Remove any instances where the adapter has tried to implement on a USB port
  Remove all instances of the downloaded driver files.
  Restart the computer. There should be nothing about it that the adapter can use more
   
  Then download a SINGLE instance of the pilots approved here. http://hawkingtech.com/products/hawking_products/Hi-gain_wireless_networking/HWUN4.html
   
  According to the manual, you must run the file from the driver before connecting the device to the computer...
  Connect the device and then run the driver file. Restarting after the installation of the drivers and when the computer is back running, connect the device...
   
  If you no longer have the manual or quick setup guide, get from here...
  http://hawkingtech.com/products/hawking_products/Hi-gain_wireless_networking/HWUN4.html
   
   
   

• New HP Elitedesk 800 G1 - no wireless adapter?

  I have a HP EliteDesk 800 G1 nine compact PC running Windows 7 - code H5T99EA. It does not have a wireless adapter - certainly none appear in the profile of Harware.

  I can only connect to the Internet via an ethernet cable. I have no option to connect wireless and my wireless router is not discovered when I try (or any other local Wi - Fi access point.

  Do I have to download a driver for the wireless card - no doubt, there is one installed?

  Thank you

  John

  Is an optional scheme, see the specification page 4.

  Integrated Intel® I217LM Gigabit network connection; available wireless LAN card

  http://www.HP.com/hpinfo/newsroom/press_kits/2013/HPDiscover2013/HPEliteDesk800_datasheet.PDF

• Which card wireless adapter for Compaq Presario model # SR5510F?

  I have a HP Compaq Presario model #SR5510F and I want to connect wireless to an AT & T 2-Cable Modem.  I need to know what wireless adapter card works for this model.  Thanks in advance.

  Message edited by morrow on 11/19/2009 05:54

  Which wireless standard using the ATT solution? Any spare wireless card should work fine, just for the game to the network.

  See you soon,.

• How to activate the wireless adapter

  I currently have a HP Pavilion 17 computer laptop with Windows 7 Professional.  A few times in the past in the unit's wireless adapter stopped working.  I don't remember what I did to get it working again, then however at this time I can not activate even if I followed all the steps to change the settings of the adapter on the network and sharing Center.  When I select Connect, it simply shows that it is not connected.  Nothing I have tried seems to help.  I have a unit of Belkin Wi - Fi that works and my laptop runs as long as I have an Ethernet cable connected.  However if I disconnect the cable from the laptop does not connect via wireless adapter.  In the past he would always stay connected to the Wi - Fi connection even if I disconnected the cable.  Please give me any thoughts you had to solve it.  Thanks in advance for your efforts and help.

  I just wanted to know that I found the solution to my problem with the help of a response of the same issue posted last year.  Repeated pressing the F12 key with the picture of an airplane on the wireless card.  Forgive my ignorance, but thanks to all who took time to try to help me.

  OldmanDon

• Cannot connect Stor.E Wireless Adapter + 1 TB HDD in my laptop

  I recently bought a Stor.e wireless adapter for use with my partner Stor.e 1 TB HDD laptop but I can't seem to connect to my laptop.

  If I plug the HARD drive directly into my laptop everything appears also ok but if I connect via the wireless adapter that shows nothing. the instructions that come with the adapter are very poor, but after following the instructions stating "plug drive HARD adapter using the USB cable then plug taken adapter (AC power), the LED flashes of HARD drive and the lights on the wireless adapter showing 1, 2 green, solid = power, wireless = 3 green, strong." USB = blue.

  The disc shows hard on my Android phone and the android Tablet but won't connect, when you perform a scan for wireless on my laptop devices, the adapter cannot be found.

  I sent twice, the support from Toshiba on July 5 and July 10, but have not received the courtesy of a response although confirmation of receipt of my e-mail, so for them we will get back to you in the DAY a statement.

  ANY help with this problem would be highly appreciated.
  Thanks in advance.

  Hello

  Stor.E WLan adapter extends a USB HDD with the ability to access data stored via a WLan connection.
  This means that you must activate your WLan on your laptop and configure the Stor.E WLan adapter first.

  The 3 LEDS have the following meaning:
  Above 1 LED is on / off and lights up green if the adapter is running
  The LED 2 is WiFi link and turns green where wi - fi access has been established.
  The 3rd (first from the bottom) lights up blue when the HARD drive is mounted. Flashing LED means read/write mode.

  How to connect?
  Connect adapter to Canvio Stor.E WLan adapt to the B USB 2.0 (near the reset button) microphone connector and connect the USB HDD to the type A USB 2.0 connector.

  You will need to activate the laptop s Wlan and press the reset button (hold it long 4 sec). The Wireless settings, you should see the Canvio Stor.E open wireless card that you connect access point.

  Then, in the Web browser using IP address: "http://198.168.65.1" to access the settings page of the Canvio Stor.E wireless adapter.

  In the preview, you can see the current version of the firmware, storage devices, network access point information.

  The list of devices shows detailed information on connected devices.
  Within the network, you can find the devault sotre.e wireless adapter network settings

  Now, you can use an Android application called Toshiba Wireless Adapter to move files on the HARD drive connected to the WiFi adapter from your smartphone.

  You can also map the card wifi as a network drive in Windows system.
  In type of Explorer: \\198.168.65.1. then right-click and choose map network drive.
  In a new window, select the application letter to the new drive (Z) and click the Finish button.