y510p immediately stops when unplugged

When I unplug it, the laptop turns off immediately.

The battery only charges to 92% and go any higher.

Does that mean my battery is defective and needs to be replaced?

Do this test-

(1) turn off the laptop.

(2) turn off the power. Keep the battery connected.

(3) try to turn on the laptop.

If the laptop does not light up, the battery is faulty.

You can contact the HelpDesk technique Lenovo by Chat, e-mail or call ()best way) and get a new battery. If you are in warranty, they shouldn't charge you.

Note - important Do not attempt to unplug the laptop while it is running, sudden stop can cause damage to the laptop. (Your HARD drive may fail)

Tags: Lenovo Notebooks

Similar Questions

  • end of 2011 MBP stops when unplugged

    Hello, my MBP end 2011 (on 10.9.5) was most recently at apple, the logic board has been replaced. shortly after that I came back, he began to stop once unplugged. Re-start works, but only for a minute. system report states that, whatever it is the air out here? Sounds like a battery problem, I'm on the original battery, but I thought battery would just shrink, not just stop working.

    Information model:

    Serial number: D8 * LAZ

    Manufacturer: SMP

    Device name: bq20z451

    Pack Lot Code: 0

    PCB batch number: 0

    Firmware version: 406

    Review of equipment: 2

    Review of cells: 158

    Information on this charge:

    Charge remaining (mAh): 6432

    Fully charged: Yes

    Loading: No.

    Full Charge capacity (mAh): 6433

    Health information:

    Cycle Count: 405

    Condition: Normal

    Battery: Yes

    Amperage (mA): 0

    Voltage (mV): 12484

    Parameters of power system:

    Alternating current:

    System timer (min): 0

    Disk sleep timer (Minutes): 0

    Display sleep timer (Minutes): 30

    Wake up on the evolution of the ca: No.

    Wake up to the opening clamshell: Yes

    Wake on LAN: Yes

    Current generator: Yes

    View Sleep uses Sun: Yes

    GPUSwitch: 2

    PrioritizeNetworkReachabilityOverSleep: 0

    Waiting period: 4200

    Standby mode enabled: 0

    Battery power:

    System timer (min): 15

    Disk sleep timer (Minutes): 10

    Display timer (min): 15

    Wake up on the evolution of the ca: No.

    Wake up to the opening clamshell: Yes

    View Sleep uses Sun: Yes

    GPUSwitch: 2

    Reduce the brightness: Yes

    Waiting period: 4200

    Standby mode enabled: 0

    Hardware configuration:

    UPS installed: No.

    Charger AC/DC Information:

    Connected: Yes

    ID: 0X0100

    Wattage (W): 85

    Review: 0x0000

    Family: 0 x 0085

    Serial number: 0 x * 4bd

    Loading: No.

    < personal information under the direction of the host >

    Hello marc cardwell,.

    If your MacBook Pro stops unexpectedly when you unplug your charger (despite correctly recognizing your installed battery), it can help restore his MSC and NVRAM.

    Reset the management system (SCM) controller on your Mac.
    https://support.Apple.com/en-us/HT201295

    How to reset the NVRAM on your Mac.
    https://support.Apple.com/en-us/HT204063

    Sincerely

  • Portege M100 stop when unplug the a/c adapter - battery problem

    Hi people,

    Laptop for my wife, it's a Portege M100 3 or 4 years, which is seems a good machine, although the hard drive failed and had to be replaced recently.
    However, there is also a problem with the battery charging.

    The machine works very well when connected to AC power whether the battery is or not, but as soon as you remove the power cable it stops working immediately, it is to say everything, including the fan stops immediately.

    The sign of the battery on the top edge of the screen/cover blinking orange.
    I figured it was the battery that had given up and bought an another toshiba (IE not a compatible but the real thing) and he slotted in but still.

    This problem above the hard drive has been changed also.

    Any thoughts or ideas?
    Thank you very much

    > The sign of the battery on the top edge of the screen/cover blinking orange
    Are you sure that it is a LED battery?
    AFAIK the battery LED indicates the State of charge of the battery.
    Green: charging completely charged and orange way. But in both cases the LED does not flash/blink.
    Only the power adapter LED will Flash orange if feeding malfunctions and the voltage is abnormal.

    But if the battery LED flashes then I guess this code refers to the battery failure.
    You should always buy a battery recommended by Toshiba and not other 3rd party products.
    The manufacturer of the HARD drive is not important, but if the battery is dead so you can buy one that is part supported by Toshiba

  • 2000 - 369wm: hp 2000 only stops when unplugged for awhile

    Our laptop stops completely at the bottom if it is disconnected.  It will work for awhile then all go off.  You can restart and it will say it didn't close properly and boot back, but then cut randomly somewhat later.  Already replaced the battery and it is still more than half charged when it arrives.  If the power cord is plugged in it stays on without problem. Help!

    @starvision ,

    Hello and thanks for the display on the HP support forums.  If you have already replaced the battery, and this problem is still there, then you have a problem with the fuel system on the motherboard that connects to the battery.  You will want to contact HP support by phone for repair options.

    Please contact our technical support at the 800-474-6836. If you do not live in the United States / Canada region, please click the link below to get help from your region number.

    http://WWW8.HP.com/us/en/contact-HP/WW-phone-assist.html

    Thanks again for posting and have a great day.

  • Sylvania SMP2012 2 GB Media Player stops when unplugged

    Why not stop and not play once it was disconnected, I don't know if it does not charge or what is the problem, but it does not work if it is not connected to the computer. Help please!

    Hello

    Have you contacted the manufacturer: Sylvania?

    http://www.sylvaniaconsumerelectronics.com/support/

    You can download a manual for it from the link and Support Contact options are there, too.

    See you soon.

    p.s. and something for the moderators to pass.

    On Windows 7 compatibility site, two of the three links Sylvania are not where they should be.

    You would like to spend on "high".

    http://www.microsoft.com/windows/compatibility/Windows-7/en-us/Details.aspx?type=Hardware&p=Sylvania%20SMP2012%202GB%20Media%20Player&v=Sylvania&uid=SMP2012&l=en-US&pf=0&pi=3&c=MP3%20%26%20Media%20Players&sc=Other%20Media%20Players&os=32-bit

  • Laptop stops when unplugged from the sector

    Battery check reads well, does not start on battery

    Sounds like the battery is dead.  Replace or test professionally.

    "PeteXJR1300" wrote in the new message: * e-mail address is removed from the privacy... *

    Battery check reads well, does not start on battery

  • MBP stops when no charging current and 99% battery

    About a day ago, my laptop (13 '' mid-2012 MacBook Pro) stop when I unplugged my charger. I have tried rebooting, but nothing happened when I pressed the power button. I plugged it in, and it began to restart immediately. Since then, the condition of the battery has been marked as 'Replace' now and it closes fully when I cut the power - even time is 00:00 01/01/15. At this point, I doubt that it is a software solution, and I wonder if it's the battery or an internal connection that went wrong. I didn't let it fall or spill anything on the subject beforehand, and I can provide a record of all the stops if necessary. The only thing that changes is recently I replaced my old hard drive with a Samsung 850 (possibly EVO, not sure) about two months ago. Thanks for the help!

    Please make an appointment at the Apple Store - Genius Bar store and bring it into service. If you are in the United States or is unable to make an appointment in this way, contact your Apple store.

  • suddenly stops when the external usb hub is attached

    My imac 27 inches 5 k 2015 suddenly stops when an external USB hub is attached supposedly designed specifically for the mac. (Cutting) The mac does not start I have to unplug it and reconnect to restart. I tried different hubs of this manufacturer and all do the same thing. Remove the hub, the computer is fine. Any ideas?

    Well, try an another factory USB hub, I had good success with USB hubs powered from Belkin.

    Question... are the hubs help powered or are bus powered USB? They are bus powered USB is your problem, the USB ports on iMac didn't supply enough power to power bus-powered USB hubs.

  • HP: Laptop randomly stops when it hits 15%

    He started only today. My laptop would randomly just turned off when the battery was low. When I checked the percentage it shows 15% when I turn on my laptop. I already checked power options, and everything is normal. I was wondering if anyone has solutions to this. In addition, I notice just that my phone would not charge from 90 percent. It would charge up to 90%. Thanks in advance.

    Hi @davevidduong,

    Welcome to the HP forums! It's a great way to engage, ask questions and find resolutions by working with specialists from the community of HP. I understand that your laptop randomly stops when the battery is low. It will be a pleasure to help you here.

    A remarkable work has been done by checking the power options. You did awesome troubleshooting before you post your question in the forums of HP. It's always a great pleasure to work with tech-savvy and technically customers sounds like you. Kudos to you for this. I am amazed at your technical skills and levels of technical knowledge.

    For clarity, I would need more information to help you best.

    Please let me know the product # computer.

    Have you checked if it stops when the charger is connected?

    This could be a hardware problem with the battery and we need to insulate it properly. In the meantime, please try a hard reset first. Steps to follow:

    • Turn off the computer and unplug the charger. Then remove the battery only if it is removable.
    • Press and hold the power button on the unit for 15 seconds to carry out the static electrical charges inside the machine.
    • Replace the battery and the charger plug it back.

    Then visit this link to update the bios and HP support assistant. Link: http://hp.com/drivers please select the country and follow the on-screen instructions. Once this please visit this link to run hardware diagnostics on the battery and other components. Link: http://support.hp.com/in-en/document/c03467259 if please run full diagnostics and note any failure code if a component fails. Mainly to run diagnostics on the battery. According to the information that you could later calibrate the battery.

    I really hope things the excellent work and the problem is solved without hassle. I hope this helps. Please let me know how it goes. Just to say thank youPlease click the ' Thumbs Up ' button to appreciate my efforts. If it helps, Please mark this "accepted Solution".

    Take care now and have a week coming Holy.

  • Outlook 2010 beta stops when I try to open it.

    I installed a Microsoft add-in called Social connector, which was bound by a contact. Now Outlook 2010 does not open. It loads my profile, and then the opends program and then immediately stops. Anthony

    Outlook:

     

    http://answers.Microsoft.com/en-us/Office/default.aspx

    Office at the above link forums

    http://answers.Microsoft.com/en-us/Office/ee861097.aspx

    Outlook Help Forums at the link above.

    http://social.technet.Microsoft.com/forums/en/Outlook/threads

    Use this forum to discuss the beta version of Outlook 2010.

    They will help you with your Outlook questions when repost you in the Office Forums above.

    See you soon.

    Mick Murphy - Microsoft partner

  • BlackBerry BB Z10 Z10 stops when the battery indicator shows about 35%

    Z10 BB stops when the battery indicator shows about 35 percent without any warning. Does not illuminate until the charger is plugged. Immediately shows charge remaining 40% +.

    Please advice.

    Stephen

    Hello

    Here is a solution I tried after lookng through various forums and type of works for me. A common thing in most of the solutions is to take the battery and sim card out, leave like this for 1-2 hours and put them, I found back in and turn it on. I'm not sure of the logic behind it, but I remember reading that this overshadow the phone battery problems (connected incorrectly - essentially a reset) and begins to charge.

    I tried it 2 days back and I see that it worked for me, at least until now. I cross my fingers.

    I hope it's useful, works at least for few of you.

    Thank you all for the suggestions.

  • Photoshop immediately stops and I get an error.

    When I open Photoshop it immediately stops and I get an error.  Is there a problem with CC?  I also had the same problem with Illustrator and InDesign.

    OK, so it crashes.  You can view the details of the accident in the system event viewer or reliability reports (you need the name of the failing module).

    The most likely cause of a crash on launch in Photoshop would be a bug in an outdated video card driver.   But that would not explain problems in Illustrator or InDesign.

    Using font management utilities that could interfere with Photoshop, ID and AI?

  • Recording stops when the alt - tab to another program (win7 64 bit)

    I've recently updated to Audition 3.0 so I could use Audition on my new Win7 64-bit configuration.

    Everything seems to work quite well except...

    When registering, if I leave the hearing program (for example, to use my browser while making a recording) recording immediately stops.

    Anyone encountered this?

    Is there a setting some part that I forgot?

    I'm sure that's not the way it should work - Win XP & hearing 1.1 worked well while multitasking.

    Appreciated by the suggestion.  Thanks in advance.

    Change-> setup of Audio material

    Uncheck 'Release ASIO Driver in the background'

  • My iPhone 6 installed 10.0.2 stops when it gets to 40% of autonomy.  In addition, it seems to pass power WAY to fast with the new software.  Does anyone else have this problem?

    My iPhone 6 installed 10.0.2 stops when it gets to 40% of autonomy.  In addition, it seems to pass power WAY to fast with the new software.  Does anyone else have this problem?

    Hello brooksm549,
    Thank you for using communities of Apple Support.

    I got your message which, since updating your iPhone 6 to iOS 10.0.2 your iPhone stops when it is 40% and the power to empty very quickly. I understand your concern with the iPhone turn off and drains the battery. I recommend you to review the use of the battery to see what app contributes more to the battery drain. The following article will provide you with steps on how to check the use of the battery:

    On the use of the battery on your iPhone, iPad and iPod touch

    When you know about the soft uses more battery, you can change your settings in order to optimize the battery life:

    Maximize the life of the battery and battery life

    Best regards.

  • Hi all, I keep is typed in the password at startup box, in bars in safari and firefox coupled with a stuck key noise that stops when you press a key, I scanned with antivirus that seems clear, can anyone help?

    Hi all, I get a storm of +'s typed in the password at startup box upward, in bars in safari and firefox coupled with a stuck key noise that stops when you press a key, I scanned with antivirus that seems clear, can anyone help?

    Clings in the key on the keyboard? Wired or wireless keyboard?

    Try to run this program, copy and paste the result in a response. The program was created by Etresoft, a regular contributor.  Use please copy and paste the screenshots can be difficult to read. On the screen with the Options, please open Options and tick the boxes in the bottom 2 before the race. Click on the button "Report share" in the toolbar, select "Copy to Clipboard" and then paste into a response. This will show what is running on your computer. No personal information is shown.

    Etrecheck - Information System

    Reset an Apple Bluetooth mouse or Trackpad wireless keyboard (pairings and other common troubleshooting problems)

    Restart your computer, hold down the option/alt - P - R keys command before the gray screen appears. Continue until you hear the startup chime for the second time.

    Reset the NVRAM EXTRA memory

Maybe you are looking for

  • Firewall always off at startup

    Hey,. Everytime I turn on my firewall, next time I start my computer it is off again. I don't know when it started to happen. I thought it might have something to do with mackeeper, anyway I uninstalled this application of spam and a clean set of El

  • Skype has stopped working! Access violation

    I get this error whenever I try to start Skype: Access violation at address 6A0CC01F in module 'mshtml.dll. Read of address 06DAB589. What can I do? Thank you!

  • How to remove the cursor hourglass?

    After downloading ie8 my cursor is attached to the hourglass. Also, keep to receive a message saying that needs to close my toolbar of the AT and T?

  • HP Officejet Pro 8600: Lost printer installation CD... Help!

    I'm at my wits end... In a nutshell, here's the deal... For some reason, my printer stopped printing.  Lost my installation CD, so I went online and I tried everything.  That's what I've done so far... -Uninstalled everything that has to do with my p

  • BlackBerry Smartphones downloads on my BB and Windows live messanger

    When I download free articles from the BB App World is that all fall under my free internet usage unlimited for BB browser? When I use Windows Live Messanger etc on the BB made also this fall under my use of unlimited free internet for BB brower?