0x0000009F during recovery mode sleep on ASUS K53SD

Similar Questions

• X 51 R2 is very slow recovery mode sleep (windows 8.1, 100% of disk in the Task Manager)

  My X 51 that R2 is very slow recovery mode sleep (windows 8.1, 100% of disk in the Task Manager).  I ran the online support tool and Support tool help.  It takes 3-5 minutes before using the drive falls down to a normal level and the PC can be used.

  Please help.  Thank you.

  Hello

  This may have something to do with the settings in Windows 8.1. Take a look at this Microsoft Community forum thread, it may be useful.

• P2715Q will be unreliable recovery mode sleep or restart using mDP to DP cable

  Monitor = P2715Q
  Graphics = Intel HD 530 (latest driver)
  Cable = Dell CDM DP
  Processor = i7 6700 k, 16GBOperating System = 10 64-bit Windows (latest drivers, bios etc..)
  Display set to 3840 x 2160 x 60 - DP 1.2
  Motherboard Asus Z170-AR with the latest version of the BIOS

  System and the monitor are brand new. Everything worked fine for the first two weeks with my old Dell monitor connected to the monitor with DVI and HDMI on the motherboard, running at 1920 x 1080 x 60. After about 2 weeks, I bought the new Dell P2715Q monitor for 3840 x 2160 x 60. Everything seemed fine at first. Then after a few weeks, I started to notice problems more and more. In the beginning, it was just a problem with the desktop icons are rearranged after the awakening of the energy saving mode. Then I started having problems with the monitor that comes out of sleep at all (I have to press the reset button on the computer to restart). Now, I have big problems with the monitor immediately go to sleep when I try to log on my Windows account. More half the time, the monitor correctly will not resume from the computer being asleep or reset the system warm or cold. After 2, 3 or 4 press the reset button, my office will finally load.

  The display often spend in good energy saving mode when I get my password to access my account from windows, and of my desktop never loads. Therefore, it seems that the problem has nothing to do with Windows, drivers or other software. He points to hardware and/or software or defective cable between the motherboard and the monitor problem. Good DP 1.2 communication does not occur systematically.

  Please tell us which graphics drivers have been tested with this monitor to work properly with 3840 x 2160 60 Hz, DP 1.2.

  Please let know us if there is an update of the available monitor firmware to solve this problem. The current version is A03, which seems to me later.

  I tried many things to solve this problem (uninstall and reinstallation, checking registry for information exact EDID, using different drivers Intel graphics, monitor reset to the factory settings, etc..)

  Please tell us what other steps can I take to solve the problem.

  Most of the users who got the A03 never spokesperson. They had to cross an Exchange used Dell to get the last revision.

• Recovery mode sleep using external USB keyboard

  Hello

  I use a R400 with XP pro sp3. At home, I connect an external monitor and keyboard usb (logitech) + mouse (ms), but not using a docking station. When not to use the laptop I obviously put it in standby mode, but for the wakes, I have to open the cover and press the power button, not very practical.

  There must be a way to wake up using the mouse or the keyboard, but I have not yet found how, even after a bit of googling autour. I have all the software usual lenovo/TV installed to the latest version (including keyboard customizer), so I can use right-ctrl + F4 from the external keyboard to go to sleep - but do not resume.

  In the BIOS, I change the setting for USB keep the power on in all power States, but this did not help. Another thing to check/change?

  see you soon

  in the power manager, check the box for usb still on its global power parameters

• Satellite Pro A100 - recovery mode sleep with keyboard or media remote

  Hi guys

  I have devoted my Satellite Pro A100 to be a media center which is located under the TV and can play media network and DVD etc..
  It is using Vista.

  I want to set up, is that the lid is closed 24/7 365 days and when I want to use I just press "SLEEP" or power button on the remote control or the keyboard and it fires up ready for action.

  POINT TO THE NOTE. I did it successfully with my OLD Tecra M3. However, was too slow for vista and media center

  However, I put the power settings I want etc, close the cover nothing and activated standby hybrid (favorite sleep).

  Now I CAN put it to sleep with the remote control or the multimedia keyboard. BUT I can wake up?... NO!. I thought about everything... went to the Device Manager and made sure that all the options for the remote control and keyboard and USB receiver are set to WAKE FROM SLEEP. The only thing to wake up it is the power button - which defeats the purpose of it sitting there like a dvd player.

  awake when the remote control and keyboard function very well - I made sure that the batteries are charged.
  I have the latest version of the BIOS and speaking of BIOS there is no option power S3 I noticed, but then there were not on the M3 and it worked very well in terms of sleep and wake up with the IR.

  I come to the forum because even though I know that some older systems will not work with vista - IF the M3 will work - I'm sure that the A100 twice as new and powerful.

  Has anyone had this before - that I missed it must look me in the face.

  Thanks in advance.

  PS Also lately the touchpad played upward IE left and right clickers Exchange feature so one second your work as normal the next minute you click left and right clikc menu appears. Reset the synaptic reinstalled - rebuilt - BIOS - no difference.

  When I worked in management for a large company when it started happening was not good news - it's a bad news?

  Hello

  I m not very well why it doesn t on your Satellite Pro A100 and why it works on M3.
  But the fact is that the Satellite Pro A100 doesn t support the FIR (Fast InfraRed) port and the
  Tecra M3 supports the fast infrared port.

  Maybe this could be the reason why you can not activate the laptop using the infrared remote control multimedia.

  Welcome them

• TrackPoint and Touchpad stops working after recovery from sleep mode

  Every now and then when my thinkpad edge 11 out of the previous day. The pointer doesn't move. It makes no difference if I use the trackpoint or touchpad. In this case I have to restart the computer using the keyboard and then pointing devices up and running again. No one knows how to fix this? The problem does not occur every time during the recovery from sleep mode, but sometimes it does.

  Hey won1,.

  uninstall the current driver for touchpad/trackpoint for your device.

  Windows should then install its own generic drivers. now with generic drivers install, place your unit in standby mode and then resume.

  see if the same error occurs. in the meantime, go to > http://support.lenovo.com and update your drivers in the bios unit.

• optical drive disappears after recovery from sleep mode

  While recovery mode S3 sleep and looking at windows Explorer, a green bar progresses inside the address bar. During this time my DVD RW is present on the screen under the heading devices with removable storage, but as soon as the green bar comes to an end, DVD RW and even the devices with removable storage section disappear.

  This occurs only on standby S3 and I have to reboot in order to keep my DVD RW.

  The DVD - RW is a disk IDE (LG Super Multi DVD drive GSA - 4163B) with an IDE-> Sata converter to allow the use of the sata cable to the motherboard.

  Any suggestions as to why this happens in sleep mode S3 only?

  Hi Peter,.

  What is the brand and model of the computer?

  I suggest you to run the Fixit described in the article and verify.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  http://support.Microsoft.com/kb/314060/en-us

  Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  322756
   
  (http://support.microsoft.com/kb/322756/)
  How to back up and restore the registry in Windows
   
  If the problem persists, you may need to update the update of the firmware to the last by visiting the manufacturer's Web site.
   
  Hope this information helps. Response with status so that we can help you.

• I forgot my PIN for my iPhone and cannot use recovery mode because my sleep button is blocked. A certain predicamnet ik

  I forgot my PIN for my iPhone and cannot use recovery mode because my sleep button is blocked. A certain predicamnet ik

  Only thing you can do is to let die and then hold the home button when you plug it into your computer to put it in recovery mode.

  Actually if the phone is on and that you have an icloud account, you can delete it at distance of icloud.com

  Go to find my iphone and erase the phone.

• Windows Media Player 12 on Windows 7 stops working after recovery from sleep mode

  I have problems to make Windows Media Player 12 to run correctly after a system sleep (standby). It works very well after the maximum boot and for as long that the machine is not going mode sleep. It is only a problem with Windows 7 and Media player 12. All other Win 7 applications seem to work correctly. The system also works very well for Vista/Media player 11.

  I installed my upgrade Windows 7 Home Premium x 64 as a new installation on a separate hard drive. This problem exists right after installation - no other software not added. I then installed all the updates MS available and the problem has not disappeared. I installed the OS a couple of times (including a copy of Windows 7 Professional x 64) on another hard drive too and the problem remains.

  Media Player 12 works perfectly until the system goes into sleep mode - either by itself, or manually. When it resumes, Media player launches, but when you try to play something, he will only play the first couple notes of music and then freeze. Same thing with videos - it will get the first couple of frames played, and then hang. If you continue to stop and restart Media Player, eventually it will be totally suspended and after a few minutes the error "Server execution failed" message. At that point in the Task Manager, wmplayer.exe will consume is a complete base my Quad CPU (25%), do nothing. Sometimes, you can kill the process and take control of the back of the PC. Other times it crashes completely and the only thing you can do is to shut down the PC.

  Media Player 11 under Vista Home Premium x 64 on the same PC works fine. I was never able to get Media Player 12 in Windows 7 to work properly after a standby/on standby. If I reboot, everything works fine so it seems to be that something related to a problem of sleep/recovery.

  HP supports suggested restarting the service WMP network sharing.  That has not helped, but if I stopped and set to manual start, Media Player would play the sound/music but not video of several tests.  But if I stopped and began to WMP 12 a few times more the problem returns.

  Well after working with the help of HP for several days, it seems to be something between the video card and card mother / BIOS between them.  At start-up, everything works well, but after the exit mode ensures, hardware diagnostics show a failure of local video memory.  Media Player is finally touched by it.  Doesn't a lot of sense to me that this does not happen under Vista, Win 7.  You have to return the PC to HP for diagnosis/repair.

• fqdn ping fails after recovery from sleep mode

  client system is win7 64 bit

  Server DSN is isc bind 9.7 works on win 7 64 bit

  local system of fqdn ping fails after recovery from sleep mode.

  I do not think that the ping never hits the network.

  Nslookup of full domain name or name of the system only exists.

  the system name ping only succeeds.

  then after ipconfig/release, ipconfig / renew, successor to ping the domain name full local system.

  someone at - it thoughts or ideas?

  Hello

  From the description of the problem, it seems that your computer is on a domain. I suggest you post the same question on the link below. The link given below is link TechNet Support for Windows 7. The question facing you is best for TechNet forums.

  https://social.technet.Microsoft.com/forums/Windows/en-us/home?Forum=w7itpronetworking

  Feel free to write us if you have any other issues related to Windows.

• Regular disk defragmentation does not intervene. Computer can be in mode "sleep" during the defragmentation?

  Disk defragmentation. will take place every week at 01:00.  Computer is in "standby" at that time.  Is this why disk frag does not happen every week?  When I defragment manually I have to confirm the status of administrator... it would have something to do with it?  I use Windows 7 Home Premium.

  Hello Lauren,

  Thanks for posting your query in Microsoft Community Forum.

  You did it any significant hardware or change software on the computer before this problem?

  I understand that disk defragmentation does not work as expected. When this works even if your computer is in "sleep". Therefore, I would suggest trying the following steps and check if the problem persists.

  Method 1:

  Step 1: Check if the Disk Defragmenter service is running.
  a. click Start and type services.msc in the search box.
  (b) in the Services window, double-click the Disk Defragmenter service.
  c. check if the Disk Defragmenter service is set to Automatic Started .

  Step 2: The question may arise also because of the intervention of third-party software. So, I suggest clean boot of the system and check if the scheduled defragmentation works.

  How to perform a clean boot in Windows
  http://support.Microsoft.com/kb/929135

  Note: See "how to reset the computer to start normally after a boot minimum troubleshooting" to prepare the computer to start as usual after a repair. "

  Method 2:

  Try to set the Defragmenter to wake up the computer from the mode "sleep" and check if it works.

  1. Click Start, type taskschd.msc and press enter.
  2. In the left pane, click the arrow next to the Task Scheduler Library, Microsoftand Windows to expand the folders.
  3. Click the defrag folder.
  4. In the center pane, right-click on ScheduledDefrag and click Properties.
  5. Click the general tab.
  6. Check the box run with the highest privileges .
  7. Click the Conditions tab.
  8. Check the box to enable the computer to run this task and click OK.
  9. Close Task Scheduler.

  Check if the Defragmenter works to wake up the computer from the mode "sleep" as expected.

  If Disk Defragmenter does not at all, then we can see the post from Bill R TechSpec responded on 19 May 2011 in the following thread.

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-performance/Windows-7-Disk-Defragmenter-does-not-work/87965977-1252-E011-8dfc-68b599b31bf5

  Hope this information is useful. If the problem still persists, please post back for further assistance, we will be happy to help you.

• Disabled IPad can be reset using the recovery mode

  Someone with a good it knowledge doctored iPad without permission and now it can be reset using the recovery mode. While that plugged into iTunes, software downloads, iPad, then displays the Apple symbol but then returns the message "iPad is disabled connect to iTunes".

  Hi stephen158,

  I understand that, in the process of restoration of an iPad in recovery mode, your iPad rebooted and returns to the screen "connect to iTunes". This can occur if the software download takes longer than 15 minutes, how the iPad will exit Recovery mode and the software will continue to download. In this case, you should be able to put the iPad in recovery mode and choose to restore the device when prompted.

  1. Connect your device to your computer and open iTunes. If you don't have a computer, borrow one from a friend or go to an Apple Store or service provider authorized Apple for help.
  2. When your device is connected, force restart it: press and hold the sleep/wake and home for at least 10 seconds, and only release when you see the Apple logo. Keep until you see the screen in recovery mode now.
     
  3. When you see the option restore or update, choose update. iTunes will try to reinstall iOS without erasing your data. Please wait while iTunes downloaded the software for your device.
     If the download takes more than 15 minutes the device out of recovery mode, you must repeat these steps and choose restore instead of update when you return to this step.
     
  4. After the update or restore is complete, configure your device. If you have backed up your device with iTunes or iCloud and you need to restore your device in step 3, you may be able to restore from your backup during installation.

  If you are unable to update or restore your iPhone, iPad or iPod touch
  https://support.Apple.com/en-us/HT201263

  See you soon!

• How can I update my iphone 6 s to the ios10, it is now in recovery mode

  When I want to update via itunes that arising out of the message that is updated to ios 9.3.5 but I want ios 10

  If you are unable to update or restore your iPhone, iPad or iPod touch - Apple supports

  In these situations, you may need to use recovery mode to restore your device:

  • iTunes does not recognize your device or says that it is in recovery mode.
  • You see the Apple logo on your screen for several minutes with no progress bar.
  • You see the connect to iTunes screen.

  Use the link above and see if your problem is solved :)

  If there is an error during the update process:- If you find an error when you update or restore your iPad, iPhone or iPod - Apple Support

  If there is an error and the problem code:- assistance with iOS update and restore errors - Apple Support

• After download iOS 10.0.1 from mac recovery mode

  After updating to iOS 10 my iPhone 6 s to the recovery mode. I connect it to my iTunes and it said iOS 10.0.1 must be downloaded. Anyway, I have download it again but to extract process disconnects my iPhone iTunes. I have the latest version of iTunes, and even if I want to restore this happen. My phone won't turn on either.

  Follow these steps to resolve the problem with the recovery during the installation of iOS 10 mode.

  1. Connect your iPhone to your computer via iTunes.
  2. Wait about 30 seconds to let iTunes your reading device.
  3. Click Update on your computer when you are prompted, who, "is there a problem with the [device] who forces him to update or restore."
  4. Again click the update on your computer when you are prompted, "If your [device] is unable to be updated, you need to restore it to its factory settings."
  5. Click on restore if you see «your iPad cannot be updated...» "(you won't necessarily have to restore).
  6. Click Restore and update to confirm that you want to restore your device to its factory settings.

  You can also use this information to solve the problem If you see an error when you update or restore your iPad, iPhone or iPod - Apple Support

• can't get into recovery mode

  My ipad2 nonstop, first. When I press on and press and hold the power button on the top, slide stops seeing never does. Finally I connect to computer via USB and itunes. When I try to turn off hard, it just won't work. I try to get back in now theHOME and button / stop, but I never get further than the white Apple Logo.

  Just to be sure:

  Connect your device to your computer and open iTunes.

  When your device is connected, force restart it: press and hold the sleep/wake and home for at least 10 seconds, and only release when you see the Apple logo.

  Keep now until see you the recovery mode screen and wait that he eat.

  You may need to do the above, more than once as recovery mode is difficult to enter.

  Restore first as New and test. Then restore backup if you wish. If the backup is corrupt it will probably bring back the question.

  https://support.Apple.com/en-us/HT201263

  If the steps above do not help, you may need to consider at an Apple store for testing.