Recovery mode sleep using external USB keyboard

Similar Questions

• keyboard & mouse freeze after the mode 'sleep', using Windows Vista 64 home premium

  keyboard & mouse freeze after the mode "sleep", using Windows Vista 64 home premium.  I received once posted this question, an answer of "fix" to a thread that has worked.  Unfortunately, I deleted the thread. I swapped the USB connectors for mouse and keyboard, but that didn't change anything.  Could someone please re - send the wire?  I promise you that I'm deleting it this time.

  Thank you very much

  E-mail address is removed from the privacy *.

  Hi RICH0214,

  Follow these methods.

  Method 1: Follow the steps in the article.

  Device Manager does not display devices that are not connected to the Windows XP-based computer

  http://support.Microsoft.com/kb/315539 (applies to Windows Vista)

  Method 2: Scan the file system (CFS) auditor to repair corrupted files.

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833

  Method 3: Create a new user account.

  Create a user account

  http://Windows.Microsoft.com/en-us/Windows-Vista/create-a-user-account

  If the problem is resolved in a new user account, and then follow the article on how to fix a corrupted user account.

  Difficulty of a corrupted user profile

  http://Windows.Microsoft.com/en-us/Windows-Vista/fix-a-corrupted-user-profile

• X 51 R2 is very slow recovery mode sleep (windows 8.1, 100% of disk in the Task Manager)

  My X 51 that R2 is very slow recovery mode sleep (windows 8.1, 100% of disk in the Task Manager).  I ran the online support tool and Support tool help.  It takes 3-5 minutes before using the drive falls down to a normal level and the PC can be used.

  Please help.  Thank you.

  Hello

  This may have something to do with the settings in Windows 8.1. Take a look at this Microsoft Community forum thread, it may be useful.

• Satellite Pro A200: Wake up to the keyboard using a USB keyboard

  is it possible to turn on the laptop while keeping the lid closed using a USB keyboard. If Yes, what the key combination

  Hmmm I put t know if you can wake up the phone if the lid is closed, but as far as I know, it should be possible to wake the portable computer using a keyboard itself.

  Toshiba HWSetup is pre-installed with the Vista operating system. You will find in this tool an option called: wake on keyboard.

  This can be found in the keyboard tab, and you need to activate.
  In addition, please enable the USB Legacy support. This option is also in the HWSetup USB tab.

  Best regards

• Satellite A300D keyboard problem after using an external USB keyboard

  I use a Satellite A300D series laptop and while at home, I use a UBS keyboard on it, but once the laptop is used without a USB keyboard only some of the keys seem to work, I get number 6 when I press the i key.

  I thought that this could be because the USB keyboard would not have been arrested properaly when I unplugged and the portable thought he was always there, but even after the stop of the USB keyboard is the same!

  All the answers to my problem?

  Hello

  On my Satellite A300, I can get 3 when I press L. It can be done if you are using the FN + F11 key combination.
  Perhaps this option enabled on your laptop?

• Qosmio G50 - 12 q - Vista does not load after you connect the external USB keyboard

  I could acquire an enermax acrilux usb keyboard and have connected the keyboard taken 12 q at the same level where another keyboard was attacked the qosmio g50 usb and it worked without problem.

  After to start the PC with keyboard eneramx connected the qosmio has not loaded windows vista Ultimate edition and the inside wheels have been activated.
  Never happened before. I doubted the enermax

  Reconnected to the position of the qosmio USB, there on the back not granted to start-up of turbines problems
  As the enermax, that he has never blocked the startup of the operating system and to activate turbines also have plugged into the same USB port to which priority was connected a keyboard?

  Tank you

  Hi mate

  Sorry, but you message I am really hard to understand
  What I understand is that you connected an external keyboard on the Qosmio and now the laptop will not boot properly. Is this good?

  What to say; Maybe you disable USB legacy mode in the BIOS.
  Please check this!
  To enter the BIOS press F2 and everything by turning on the laptop.

• Can I use a USB keyboard (cable or wireless) with my KDLNX810 TV?

  My Sony KDLNX810 USB ports, it can be used with a USB cable or a wireless keyboard? I tried with a wireless keyboard and access to youtube, without success. Is there a driver or something that needs to be configured? Or it just doesn't work?

  I also tried to find a remote control (iphone) app, but have not found a for this model.

  Thank you

  Hello Duane,

  Welcome to the community of Sony.

  Wireless keyboards are not compatible with the TV.

  However, you can use the 101 wired USB keyboard keys with the TV.

  This TV only has not the function distance media. Therefore, it can be controlled using the remote application of media.

  Please mark it as "acceptable Solution" If you find this information useful.

  Kind regards

  Colby

• Satellite Pro A100 - recovery mode sleep with keyboard or media remote

  Hi guys

  I have devoted my Satellite Pro A100 to be a media center which is located under the TV and can play media network and DVD etc..
  It is using Vista.

  I want to set up, is that the lid is closed 24/7 365 days and when I want to use I just press "SLEEP" or power button on the remote control or the keyboard and it fires up ready for action.

  POINT TO THE NOTE. I did it successfully with my OLD Tecra M3. However, was too slow for vista and media center

  However, I put the power settings I want etc, close the cover nothing and activated standby hybrid (favorite sleep).

  Now I CAN put it to sleep with the remote control or the multimedia keyboard. BUT I can wake up?... NO!. I thought about everything... went to the Device Manager and made sure that all the options for the remote control and keyboard and USB receiver are set to WAKE FROM SLEEP. The only thing to wake up it is the power button - which defeats the purpose of it sitting there like a dvd player.

  awake when the remote control and keyboard function very well - I made sure that the batteries are charged.
  I have the latest version of the BIOS and speaking of BIOS there is no option power S3 I noticed, but then there were not on the M3 and it worked very well in terms of sleep and wake up with the IR.

  I come to the forum because even though I know that some older systems will not work with vista - IF the M3 will work - I'm sure that the A100 twice as new and powerful.

  Has anyone had this before - that I missed it must look me in the face.

  Thanks in advance.

  PS Also lately the touchpad played upward IE left and right clickers Exchange feature so one second your work as normal the next minute you click left and right clikc menu appears. Reset the synaptic reinstalled - rebuilt - BIOS - no difference.

  When I worked in management for a large company when it started happening was not good news - it's a bad news?

  Hello

  I m not very well why it doesn t on your Satellite Pro A100 and why it works on M3.
  But the fact is that the Satellite Pro A100 doesn t support the FIR (Fast InfraRed) port and the
  Tecra M3 supports the fast infrared port.

  Maybe this could be the reason why you can not activate the laptop using the infrared remote control multimedia.

  Welcome them

• P2715Q will be unreliable recovery mode sleep or restart using mDP to DP cable

  Monitor = P2715Q
  Graphics = Intel HD 530 (latest driver)
  Cable = Dell CDM DP
  Processor = i7 6700 k, 16GBOperating System = 10 64-bit Windows (latest drivers, bios etc..)
  Display set to 3840 x 2160 x 60 - DP 1.2
  Motherboard Asus Z170-AR with the latest version of the BIOS

  System and the monitor are brand new. Everything worked fine for the first two weeks with my old Dell monitor connected to the monitor with DVI and HDMI on the motherboard, running at 1920 x 1080 x 60. After about 2 weeks, I bought the new Dell P2715Q monitor for 3840 x 2160 x 60. Everything seemed fine at first. Then after a few weeks, I started to notice problems more and more. In the beginning, it was just a problem with the desktop icons are rearranged after the awakening of the energy saving mode. Then I started having problems with the monitor that comes out of sleep at all (I have to press the reset button on the computer to restart). Now, I have big problems with the monitor immediately go to sleep when I try to log on my Windows account. More half the time, the monitor correctly will not resume from the computer being asleep or reset the system warm or cold. After 2, 3 or 4 press the reset button, my office will finally load.

  The display often spend in good energy saving mode when I get my password to access my account from windows, and of my desktop never loads. Therefore, it seems that the problem has nothing to do with Windows, drivers or other software. He points to hardware and/or software or defective cable between the motherboard and the monitor problem. Good DP 1.2 communication does not occur systematically.

  Please tell us which graphics drivers have been tested with this monitor to work properly with 3840 x 2160 60 Hz, DP 1.2.

  Please let know us if there is an update of the available monitor firmware to solve this problem. The current version is A03, which seems to me later.

  I tried many things to solve this problem (uninstall and reinstallation, checking registry for information exact EDID, using different drivers Intel graphics, monitor reset to the factory settings, etc..)

  Please tell us what other steps can I take to solve the problem.

  Most of the users who got the A03 never spokesperson. They had to cross an Exchange used Dell to get the last revision.

• Satellite A200: Cannot properly use external USB devices

  I encountered a problem with my Toshiba laptop and I can't fix it, and I'm in need your help please...
  The problem is that when I connect a USB portable device (an external hard drive, USB, iPod, Flash memory... etc) with more than 8 GB of memory...
  It is not properly installed in the Device Manager and appears under "USB bus controllers.

  But it does not say that it is an unknown device. It normally appears with his name, but he is not properly installed (it does not say that either) where it is supposed to be a camera under "imaging devices" in a specific category (hard drive under "drives"), and so on

  And I can't use the unit because the HARD disk does not appear in 'My computer' and my iPod cannot be used

  I would like to inform you that this problem is with all USB devices with more than 8 GB of memory.
  Not a single device. I tried a lot of features to ensure that it is not a problem with the unit.

  So this is a problem with my laptop and I installed Windows several times but no progress.
  Thanks for your help in advance...

  Is it XP or Vista?

  If its XP, make sure you have at least Service Pack 2.
  This hotfix can help XP see large capacity media:
  http://support.Microsoft.com/kb/934428
  but that doesn't really affect USB external HDD.

• Problems using external USB hub with A30

  I have a Toshiba Satellite A30-514 with a USB powered 2.0 hub attached. In it's plugged a powered satellite Receiver/USB modem (for connection broadband), a USB bluetooth adapter and a HP PSC 1350 printer. The first two devices work fine, but the printer is not recognized correctly.

  The powered USB hub is plugged into the first USB port on the laptop. The second USB port on the laptop is used by the receiver for a wireless optical mouse. It must be here otherwise, it does not work.
  If I plug the printer directly into the second USB port on the laptop, it works fine.

  In Device Manager, instead of show all HP devices it comes to peripheral USB Composite in the USB controllers section. It is an orange exclamation next to him.

  If I boot the laptop with all 3 devices plugged into the hub and turned on, the printer is detected fine but the Bluetooth Radio devices have an orange instead exclamation point. I need the bluetooth device to attach a cell phone to the laptop. If I unplug the printer and restart the bluetooth is detected OK. Plug the printer in causes the Composite device to reappear with the exclamation point!

  From left to right, looking at the front of the hub, devices are 1) satellite receiver/modem, 2) Bluetooth printer) 3.

  I hope it's clear. Any help / advice would be received with gratitude.

  Hello

  I think the problem is that one of the devices does not have enough power to operate. This is because a single USB port must provide 3 devices with power. If you have an external power supply to one of the features of this you should use.

  Good bye

• Hi, my Aspire Z5600 is stuck on the Windows re - screen and I can't use the USB keyboard screen

  Hi, I hope someone can help with a problem I have with my Aspire Z5600 all in one computer. I can't restart the machine because it is blocked on the page re-loader of Windows when I try to reboot.

  The screen is grey anthracite dark with white writing and gives me two options, to select one of the options that I would need to use the arrow keys on the keyboard and press ENTER to the action of the selection. The problem is fashion seems to be invalid the USB ports and the touch screen, so I can't select and option of each key board or screen and it will not pass, is just stuck on the screen, making the computer unusable.

  Can someone give me a solution to remedy to this problem please?

  USB should work even in this form, have you tried another keyboard?

• Toshiba 39L 3300 problems using external USB WLan WLM-20U2

  Hello

  Recently, I brought a 39L 3300 smart TV toshiba and got a free dongle for internet connection.

  However, I was unable to connect to internet via wifi. The dongle I got from the Bank is a Toshiba dual band wireless LAN adapter WLM-model 20U2. But it doesn't seem to work at all when connected to the USB port. I checked with the other connectors USB port to watch movies and it works well.

  The choice of type of network does not appear after the dongle is connected. Could there be a problem with this model of dongle? The user manual specifies a Toshiba dual band wireless LAN adapter WLM - 40U model. But the store gave her.

  No matter which also I have this problem, please help.

  > User manual specifies a Toshiba dual band wireless LAN adapter WLM - 40U model. But the store gave her.

  Yes, of course the problems of compatibility between the TV and the WiFi dongle could cause this problem.
  I recommend to use the recommended WLan dongle WLM - 40U for this model of TV

• 0x0000009F during recovery mode sleep on ASUS K53SD

  Hello, I have a BSOD problem when you exit sleep / but I was unable to find the driver causing, when I look at the discharge, it tells me that the problem is ntoskrnl.exe.

  I installed the patches associated with error 0x0000009F unsuccessfully with the thesis.

  Windows6. 1 - KB975599 - x 64

  Windows6. 1 - KB977186 - x 64

  Windows6. 1 - KB981848 - x 64

  Windows6. 1 - KB2459268 - x 64

  The drivers used currently in the dump on link below.

  http://1drv.Ms/1ogeuHt

  Concerning

  Hello

  The attached file of the DMP is to bug checking DRIVER_POWER_STATE_FAILURE (9f) .

  This bug check indicates that the driver is in an inconsistent or invalid power state.

  By default, the fault of the accident is pci.sys which is NOT the real cause of the accident. If we run one! IRP on the 4th parameter of the verification of bug:

  > [16, 2] fffffa8007ace050 0 0 00000000 00000000 - 00000000
  Failed to load image \SystemRoot\system32\DRIVERS\NETwNs64.sys, 0n2 error Win32
  WARNING: Unable to verify timestamp for NETwNs64.sys
  ERROR: Module load completed but symbols can be loaded for NETwNs64.sys
  \Driver\NETwNs64

  NETwNs64.sys is the Intel (r) Wireless WiFi Link 5000 Series adapter driver for Windows 7.

  Make sure that this driver is 100% up-to-date.

  -------------------------

  Remove and replace Kaspersky with Microsoft Security Essentials to temporary troubleshooting purposes, since it's likely also cause conflicts of NETBIOS:

  Kaspersky - remove http://support.Kaspersky.com/common/service.aspx?El=1464

  MSE - http://Windows.Microsoft.com/en-us/Windows/Security-Essentials-download 

  Kind regards

  Patrick

• Satellite A100-049: is it possible to turn on by mouse or external USB keyboard?

  I see no option of BIOS and single "Wake up on keyboard" in HWSetup, but that makes no difference. I suspect that refers to the keyboard on the laptop. I would like to be able to turn on the laptop, so I can leave the lid closed. Thank you

  Hi again,

  I checked my neighbours A100 Bios, as there no option for Wake-on-keyboard, too. I think that it s not implemented in this bios.
  If this helps you: try the latest bios for this machine, perhaps implementing this option in a newer version.

  Welcome man