1074384864 error [invalid reference was passed to a NOR-XET session]

Similar Questions

• Help - error invalid reference when closing file

  The problem is that the function "Close TDMS" generates the following error message:

  -------------------------------------------

  Error-2501 occurred at close TDMS in host pc.vi

  The possible reasons: Reference to invalid TDMS files.

  ------------------------------------------

  What is so strange about it, as you can see on the screenshot, is that many other functions uses the file reference without any problem whatsoever, but when it gets to the close function, an error is generated. I probed the wire of error at each step, and there is no error that occur before the close of tdms file function.

  Just to help understand the function: a file temporary tdms is created and all data from the raw data file is stored on it. A list is generated from all the names of valid channel (channels named something other than "*" "") and then these valid channels only is read from the temporary file PDM and written in the final output file. The files are so big the read and write functions must be placed in loops so that the data is read/written a line/column at the time and the entire 90 MB file is not loaded into RAM.

  Can someone help me? I really need to understand what is happening. Code examples would be useful.

  

  Change all the tunnels that you use for the refnum in those loops to Shift Registers.

  If the loop For travels '0' time the refnum passes not valid.

  Ben

• not able to open vro configuration manager if State HTTP 400 Error - Invalid reference directly to the form login page.

  

  Hello

  You are not directly correct the VRO login page login, please take new private window and open the URL. https://IP:8283 / vco-config /

• ProBook 455 G1: "Osoitin ei kelpaa" error ("invalid pointer") shown in trying to open a session

  Hello

  I'm computer fixing of my mother-in-law. The problem is the following: once installed it updates and phone rebooted it couldn't connect because the screen started to Flash (i.e. turning black and then show the new login screen). I start the computer in safe mode and loaded the last restore point. However, now I am unable to connect because once I selected (only one available) account in the login screen is shown a different login screen. "Another user" text ("Korean kayttaja" in Finnish) is on the logo and message 'check' password ("Tarkista salasana" in Finnish) under him. Below are the fields id and user password. ID field is prepopulated with his user name. After I typed his password a "invalid pointer" error ("Osoitin ei kelpaa" in Finnish) is shown.  Therefore, I can only connect in safe mode.

  I checked the most recent restore points and seems that there are a lot of updates until the original flashing problem has occurred. I tried to restore but restore points not chance.

  5.9.2015 09:36 «Microsoft Visual C++ 2012 11.0.51106 Redistributable (x 64)»

  5.9.2015 09:36 "Microsoft Visual C++ Redistributable (x 86) 11.0.51106 2012"

  5.9.2015 09:24 "HPSF app updated"

  5.9.2015 09:19 "HPSF app updated"

  5.9.2015 09:18 "HPSF app updated"

  4.9.2015 21:48 "HPSF app updated"

  Do you know how I can fix the problem so that it can connect normally? Ask if you need more information. I would appreciate if someone could help it!

  I found this solution while Googling autour:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-Security/Windows-7-logon-issue-with-message-invalid-pointer/7ff7277f-D940-4761-9268-3115c424159c

  ' 1) safe boot mode.

  (2) run MSConfig

  (3) select the Diagnostic startup option on the general tab

  restarting...

  you will get a "generic" windows login screen and be able to get your desktop... but almost all the services will be disabled and stopped, so will not work

  (4) open Services.msc, find and double-click the Windows Installer, manual exchange service and run...

  (this will allow you to uninstall programs)

  (5) Control Panel, programs and features

  (6) uninstall the HP software: file sanitizer, drive encryption, Manager access of devices and finally Client Security Manager (it is the security that must be uninstalled, but others must be removed first) - I chose the option "do not save stored configurations" (because I believe this is what is actually prescription foo ("pointers" between user names) passwords and settings stored fingerprints database)).

  (7) MSConfig again, change the Normal start".

  (EDITED ON10.9.2015. Thanks rcoffey69 for the tip!)

  If you cannot remove the Manager of HP devices access to step 6:

  7) go to control panel > remove programs and instead of delete access Device Manager, choose 'repair '.

  (8) restart and go into safe mode.

  (9) run MSConfig and change Normal startup, restart.

  (10) connection to normal mode and now you should be able to remove the HP device access Manager, restart.

  (11) remove Client Security Manager, choose 'do not save stored configurations', restart.

  Now everything should work ok again.  Don't panic if you see errors when trying to log on after step 10. You should still be able to connect. In fact, you might be able to uninstall HP device manager access (+ Manager client security) right after step 7 without the need to reboot in normal mode (?) I did not try it.

  -------------------------------------------------------------------------------------------------------------------------------

  (Former message):

  However, I can not remove the HP device access Manager because it displays an error message (translated version): "1720 error: there is a problem with the Windows Installer package." A script required for installation to complete could not be run. Contact your provider to support personal or package. Custom action script-2147023838 error UninstallDriverFromINF. Line 10. Column 2.

  This is why I can't delete the client security manager that is probably causing this problem.  I tried to remove it by using Windows Installer CleanUp Utility, but it did not help. Anyone know how to get rid of HP Device Access Manager so that I can remove HP Client Manager Security? )

• Cannot use the references in Subvi cluster (error 1055, invalid references)

  Hello

  I'm going through a lot of that through a cluster to a Subvi.

  The idea here is to manipulate objects in the MainVI in the nodes property thorugh Subvi, which gains the reference number of the cluster.

  In the Subvi, I use unbunling by name to access the references I need. However, I get an error 1055 (invalid references) every time I try to access the object by using the node property.

  What I am doing wrong?

  Attached you will find three files:

  The mainVI: Main.vi

  The Subvi: Single_Cam_RefBased.vi

  The def of the type for the cluster: RefClusterTypeDefinition.ctl

  Thanks in advance,

  Marcel

  SteveChandler wrote:

  The constant you have wired to the bundle is not the same as the cluster of type defined wired to your Subvi.

  I was going to say the same thing. This should be the first thing to try. (I haven't studied the Subvi, but it seems buggy too...)

  COMMENT: Again something is screwed in the current VI which makes no sense. Hovering above the terminal should tell us information about the corecion, but in this case it is said that the terminal is something like a cluster of error. This might just be a cosmetic bug...

  

• is itunes error message cannot connect to my iphone because of an invalid response was received from the device

  get error message that IOS 10 unable to connect to my iphone iTunes 6 because of an invalid response was received from the device

  Make sure you are using iTunes 12.5.1 or later, as it is required to communicate to iOS 10.

  If iTunes does not recognize your iPhone, iPad or iPod - Apple Support

• SmartView: XML load error: an invalid character was found in text content.

  Hello
  
  IM using hyperion 11.1.2.1 with SmartView installed with Office 2007. Many forms are works good about it, but we've entered data on a number of them recently and we are unable to open in SmartView either through the icon and menu options in the workspace or via the smartview Panel in excel 2007. The error we get is "XML load error: an invalid character was found in text content.".
  
  See you soon,.
  
  Imran

  Take a look at the Oracle Support - "SmartView XML load error:"Year Invalid character was found in text content"[968808.1 ID]".
  It may be the same problem you are having.

  See you soon

  John
  http://John-Goodwin.blogspot.com/

• I get an error message during the installation, "a reference was returned by the server.

  I.m cannot install something if it's a CD or a program stored. I tried all the patches of the windows setup program to uninstall and reinstall, tool registry and all the mister fix his. My computer is up to date and have all the patches. I always have error "a referral was returned by the server. When I installed windows Ultimate edition with a new hard drive first. It wasn't a problem.

  Hello

  See if that helps you.

  http://www.winvistatips.com/referral-returned-Server-t525024.html

  http://www.winvistatips.com/re-error-referral-returned-Server-t80125.html

  See you soon.

• clear an error: invalid value "1.0.0.0" request-requires-System. "

  Hey everybody. Recently my app had accepted in App World, and now I have to finally move to sign my application. I followed the steps listed HERE, and everything was fine until I actually went to sign my bar... it throws the following error:

  clear an error: invalid value "1.0.0.0" request-requires-System. "

  I have searched the forums and found this but (which also led to this), I came across another problem. I've been working out of my project of Mobile Flex using the SDK of heroes and everything seemed fine. It debugged very well, installing BAR was very good and above all, it has been accepted by RIM. I thought it was no big thing, but now I run into issues. The discussions I linked to had a response from an official developer of running off of the latest version of the SDK (0.9.3), but my project says that the SDK is not compatible with mobile projects.

  Someone at - it suggestions? I hope I don't have to redo something here, but I tell myself that I'll do all what I need to do my application upwards and running as it should. Thanks in advance guys!

  Edit: another suggestion was actually go in my manifest file in the META-INF and remove this line of text. I can do this, but I don't know what effect it will have and I suppose you far, far smarter than me. If I try to go and screw with my files, it can't end well.

  Haha what do you mean you're not too bright. you really made the right decision here. in the first step of creating a project, you can choose the Flex SDK hero. You cannot choose the BB SDK because it works only as a reference library.

  If you go into Preferences > Flash Builder > target platforms, what do you see here?

• iTunes could not connect to the iPhone, because an invalid response was received from the device.

  Just bought an iPhone 7 today and received the error message "iTunes could not connect to the iPhone because an invalid response was received from the device." Don't know what that means, and I have never had this problem with one of my previous iPhones. Thank you.

  You run iTunes 7.5.1? iOS10 requires iTunes 12.5.1 find which demands in turn 10.9.5 OSX or newer.  Software update checks only the updates to the current version of the system that you are running but that itself can be updated.  It may or may not be possible to upgrade your computer to the system requirements. Find your computer on the web site of http://www.everymac.com model and near the bottom of the specification of the system section, he will tell what versions of the operating system, it is able to run. If you can not run a newer system, you will not be able to sync this phone to your current computer. You can try to install the free El Capitan OSX 10.11.  El Capitan can run slower on older machines and require the additional purchase of RAM (4 GB is a minimum realistic and many recommend 8 GB).  Making a big jump in versions of system is also more likely to affect the old software.

  At el capitan Snow Leopard, it will make my macbook is slow?  - https://discussions.apple.com/thread/7412959

  Course OSX Upgrade General information, including configuration required - http://www.apple.com/osx/how-to-upgrade/

  If you have any generation of PPC software which works under OSX 10.6 it is not supported in later versions of the system.

• Invalid response was received from the device

  Now that I've updated my iOS 10 6plus my phone will not connect to my macbook pro. I get an error message stated "iTunes only could not connect to iPhone because an invalid response was received from the device. I removed the password and fingerprints, phone rebooted, macbook restarted and still does not.

  Hi kcampagna8,

  Thank you for using communities Support from Apple. We are sorry you are experiencing this problem with your iPhone. If you get an error with "an invalid response" message when you try to connect to iTunes, you can find the troubleshooting steps in the following article useful:
  
  

  Check your USB connections

  If you see the error 4005, 4013, 4014, learn what to door. If you see one of the errors below, you might have a USB connection problem:

  • 13, 14, 1600, 1601, 1602, 1603, 1604, 1611, 1643-1650
  • 2000, 2001, 2002, 2005, 2006, 2009
  • An error message that includes, "an invalid response.

  Follow these steps to see if the problem is with your USB cable, a USB port or computer. Try again after each step:

  1. Use the USB cable supplied with your device. If you do not, try a different cable USB Apple.
  2. Switch to a different USB port on your computer. Do not connect on your keyboard.
  3. Plug it into another computer.
  4. If you still see the error, you can check for any other problem USB, with the third-party security softwareand the problems with hardware.

  If the problem persists, contact The Apple support.

  Get help with iOS update or restore errors - Apple Support

  Concerning

• Get this error message: reference #30.9079ccc.1416414297.9e80d60

  Went to sears.com and put four tires in the basket. When I clicked on the "order" button I get the following error message: reference #30.9079ccc.1416414297.9e80d60

  Weird because last week I performed this operation without problem.

  I contacted Sears and they said that it wasn't a mistake there messages. The tech support guy could not reproduce the problem to an end. I went to another computer running Google Chrome and has not encountered the problem.

  I tried the website again and everything works! Don't know what was the problem but thanks for the help.

• Version with ControlLogix - link cRIO (implicit messaging), "(Code 16 #0315) problem" connection request error: invalid segment type ""

  I have developed and delivered a system in Germany several years ago.  He worked then.  But the cRIO was damaged and replaced by a newer model, and does not now.  I suspect (and Support technical OR agree) it's a problem of software version, which could be solved with the NOT-MAX Software Installer.  But I do not have access to the system myself, and correspondence is slow and tedious.

  The original system was a cRIO-9073, developed with LabView 2009.  He used the implicit Messaging.  The ID of Instance, sizes, IP addresses, etc everything has worked very well.

  The current system is a cRIO-9074, with LabView DURATION 14.0 (I guess that LV 2014), Scan Engine 4.3, NI - Industrial Communications for Ethernet/IP 14.0.0, etc.  Programs FPGA and processor are responsible and seem to work in the cRIO.  The "EthernetIP Set Assembly Instance Data.vi' will return no error.  But the PLC just pointing out "(Code 16 #0315)" connection request error: invalid segment type "."  We looked at intellectual property (the mistake was different), sizes and body #s.

  The PLC doesn't have to all be modified.

  Anyone know if there is no problem of compatibility with LV-2014 and Ethernet/IP 14.0.0?  Or if there are all the other required packages?

  I am including the NOT-Max reports.

  Hi ZX81

  To help you 2009 application to work with the new cRIO, you must deploy it to the device. You must in order to deploy the cRIO, make sure it has the same versions of software that you used with the old cRIO.

  You can format the cRIO NI MAX and deploy the application of LV, 2009. However, if you do not have access to the cRIO or your client does not have the necessary software, you can deploy the application in another cRIO with software (cRIO same model and same modules as your client) and create a picture of it and send it to your customer so that it can deploy the cRIO even without the software on his computer. The following document explains how to do this.

  Utility of RAD

  WenR

• ATML Reporting: "an invalid character was found in text content."

  When you use ATML and including non-ASCII characters (code decimal 128 and more), the generated report is not viewable in Internet Explorer (or Firefox, in fact), producing the error "an invalid character was found in text content." I think it's because TestStand isn't actually encoding the content of the report to the UTF-8 format. The same sequence produces a clickthrough report XML declaration. It seems that this issue has been found (and fixed) for the XML declaration but many years back.

  If you open the attached XML file in UTF-8 compatible text editor (I used the Notepad) and re-save specifically in UTF-8 format, IE will happily consider subsequently report. The part that really confuses me is that TestStand generates successfully the temporary HTML version of the report for the integrated report viewer (also attached), the parser used internally by TestStand must be a bit more lenient than IE.

  I've included an example with a VI sequence, which returns only a string of ReportText of these problematic characters.

  ASBO-

  Thank you for bringing This problem to our attention. This will be fixed in a future version of TestStand. In the meantime, you can fix this problem with your current version of TestStand by editing the reportgen_atml.seq file. I've attached an example of how you could modify the reportgen_atml.seq file to fix it in this position. Please, note that this is simply an example of correct behaviour and may not be the final implementation included in future versions of TestStand. I recommend that you do not replace or delete your reportgen_atml.seq file and save the version annexed to your \Components\Models directory.

  I hope this helps. Thanks again for this bring to our attention.

• Windows 2003 server the trial verson activation error: "invalid product key. Pls Help.

  I am trying to activate my trial 360days WIn 2003 version but the error: "INVALID PRODUCT KEY".

  Please any help?

  It seems that the trial was for the RC2 release of the server - not the release.

  It is time-bommbed and it has expired yonks.