1206tx envy 6: Windows install hard drive problem

Similar Questions

• Cannot install Windows 7 HARD drive problems

  Hi all!

  I have lenovo ThinkPad T540p. Intel Core I7, 8 GB RAM and 500 GB HARD drive. I think my HARD drive is Toshiba. It had Windows 7 on it, but it starts no more on this subject. When I start Windows is it shows 5 seconds black screen, and then it displays the Boot Menu. Well, I tried to reinstall Windows, but when I have to choose on which disk to install Windows, I get an error: "no hard drive found." And the list with readers is empty, so I can't reinstall Windows. I've updated the BIOS, but it did not help. Finally, I formatted my HARD drive and created two partitions on it. It worked, but not for long. I installed Windows 7. Everything was going well until I restarted my computer. And then I got the same problem: 'Cannot start from the HARD disk' and displays the Start Menu. Then I booted Windows installation and I got the same error: "no hard drive found."

  I don't understand what is happening with my HARD drive and that is to destroy his scores.

  And I don't think that my HARD drive is broken.

  I don't really know what to do!
  Please, help me!

  Thanks a lot!

  Here is the solution:

  My HARD drive was broken. I bought a new MX100 of Crucial SSd and everything is fine.

• Windows freezes; Hard drive problem?

  My daughter has an HP Pavilion g62-435dx with Window 7 Home Premium64bit.

  Windows runs a little time and freezes.  I ran the HP hard drive diagnosis advanced test and got Smart Check passed and short DST failed with code UFXB9X-5GN6A8-PXG02K - 60Q 703.

  Is the hard drive a total failure?

  Yes that's correct...

• A55 (8982 - 77G)-Windows 7 SATA Hard Drive problem

  Hi, hoping someone can help here. I just bought the above system, it came without a hard drive, as it was purchased at a business. I installed a Seagate 200 GB SATA hard drive and I am trying to install Windows 7 Ultimate... the HD is recognized by the BIOS and the POST, but the installer of windows 7 do not see, I searched relevant drivers for the motherboard... but can't find it nowhere I tried to set the Auto and Serial ATA SATA BIOS setting only with no success... Any help would be appreciated.

  Concerning

  Hi and thanks for the answer, had sorted out, seems it was a b the hard drive problem. Once I have two-way for another installation of windows 7 200 GB SATA drive picked up immediately.

  Concerning

• can I have installed hard drive window

  My dear, I have a problem. I have dell core i3 with Windows vista. When I buy my albums lab 1 window cd also available. After a while a window installed from the CD and after that I received an error when start my lab top and I can't installed some drivers like DOLL bilu and wireless. now I want to reinstall the window of hard drive... is it possible? and how it is possible

  right on the c drive, I can see folder 2 window as follows
  1 window
  2 old window
  my friend please tell what can I do now to restore the hard drive window

  You cannot reinstall hard unless make you it bootable and copy the installation files. I really don't understand what you're saying here, something about drivers. IF you are unable to install them, download and manually install (drivers on the manufacturer's Web site from your)

• Alternative to the reset by Satellite A660 for potential HARD drive problem

  In the last week or two, I got a few blue screens, saying he was driving demand, and that windows must be shut down to avoid damage my computer.

  I have just restart and continue working.
  The last time it happened, I had repeatedly "initialization failed" and it says hdd, SDS, fdd. If I pressed the power button until I didn't see no signs of activity, then started. Things went well. I called Toshiba support and they recommended that I go home and save my files before continuing. It took hours selectively to clean, sort the previous backups, and a small footprint of the backup system.

  When I called Toshiba once again, they recommended a "takeover", which is restoring the factory settings. It puts me in the stone age. I have to go through a never-ending process of the upgrade to Windows 7 Pro 64-bit, install and reconfigure all the applications and environments/configurations, etc. It will essentially take on holiday, if not more. I'll also have to get another computer (maybe a netbook) to stay in touch while I restart my laptop. It's barely more than a year.

  Is there a diagnosis I can do to determine the probability that there is a hard drive problem? Support for Toshiba said that is the surest way, because it provides a diagnostic F10 for the hard disk code, and it also pushes the bad sectors at the end of the disc (logically, I suppose, since you can't physically move a fault).

  > About Hitachi DFT, is it important that my HARD drive is Toshiba mk6465gsx? This is what is displayed "Hard drives" in the Device Manager.

  It s no matter what HARD drive manufacturer, it is the Drive Fitness Test is able to scan all hard drives to find errors.

  > Also, http://www.hitachigst.com/support/downloads/#DFTshows links to create boot disks, but I was wondering if I could create a bootable instead.

  Not sure if this is possible if there is that one option to create a startup disk, and then a flash stick does not work. But of course you can try this out.

  > This laptop does not come with a floppy drive, and I still create coasters trying to burn discs.
  You don't need the floppy drive, the tool must create a disk bootable (CD)

  > I guess that the same question can be asked on Memtest86. Another issue is the relevance of Memtest86 for my system. My c drive has a "Program Files" folder, but also a "Program Files (x 86)" folder for 32-bit applications. Memtest86 is for the x 86 architecture. I don't know if my 64-bit Windows 7 involves a non - x 86 architecture.

  I guess that Memtest86 should also work on Win 7 64 bit systems. But also the MemTest 4.20 is 64-bit capable

• Qosmio F60 turning is not on - HARD drive problem

  My F60 running stock windows 7 and when I turn it on I get a black screen with the following text:

  + Check the file system on C: +.
  + the type of file system is NTFS.
  + Volume name is s3a5802d002 +.
  + One of your disks needs to be checked for conisitency. +
  + You can cancel the disk check, but it is strongly recommended that you continue.
  + To skip verification of the disc, press any key within 10 seconds.

  If I leave it just like that.
  I try to ignore it, and it does not work so I turn it off and go again on the third time, to turn on while I press ESC. What should I do about it?

  Re: do everything or send it as it is only 6 months old, it is Bernard did this for 5 months

  Hello

  It sounds a bit like a HARD drive problem.
  I recommend checking out the HARD drive using a free tool called Drive Fitness Test
  This free tool allows you to get more details on the State of the HARD drive and maybe some error would be detected which would mean that HARD drive failures and disk HARD must be replaced.

• I am a member of the creative cloud.  I had hard drive problems.  How can I go on redownloading cc lightroom and photoshop

  Hello

  I am a member of the creative cloud.  I had hard drive problems.  How can I go on redownloading cc lightroom and photoshop

  Refer

  Using creative cloud | Download, install, update or uninstall applications

• How can I move the Virtual Mode of Windows XP hard drive to another drive

  How can I move the Virtual Mode of Windows XP hard drive to another drive?

  TIA

  Hi Benyl,

  The vhd in programfiles basis cannot be moved or renamed, if done, xp mode stops at the start.

  To move the files under c, first to boot xp, instead of save mode the machine virtual., turn it off. (settings to prompt the user for action narrow close). Close the machine virtual., and then choose stop. This will remove the vsv file. Do not delete the .vsv file because it contains data if you have not registered in the virtual machine.

  Now, move it "C:\Users\CHRIS.domainname\AppData\Local\Microsoft\Windows virtual PC\Virtual Machines\Windows XP Mode.vhd" to a desired location.

  Parameters of xp mode open, go to the hard drive 1 setting and reposition the hard drive to the new location of the vhd. You should now be able to start the virtual machine.

  Thank you, and in what concerns:
  Shalini Surana - Microsoft technical support.
  Visit our Microsoft answers feedback Forumand let us know what you think.

• K015dx m6 ENVY: envy m6 k015dx - no hard drive detected on a clean install of windows 10

  Hello, after upgrading fromwindows 8 to 10, windows starts not more and I can 't repair.

  the only option is to reinstall windows 10 (new installation).

  The problem now is that windows 10 does not see the hard drive, I'm trying to install the driver of intel rst but not at all, the hard drive and partition are not seen. I have successfully test the hard disk with bios diagnostic.

  No idea on how to solve this problem is welcome?

  Thank you in advance

  I have me there final put another hard drive and it is detected by all the different operating system installer.
  It seems that Windows corrupted 10 hd, I use a usb adapter TO connect the old one on another computer, hard drive was visible, but not initialized. I m not the only one having this problem, I received a call from someone Salinger for help.
  Thank you for your support

• Newly installed hard drive, cannot get the reinstallation of Windows 7 to the end

  Hi all. My factory-issued Seagate 1 TB hard drive of origin provided with my PC Pavilion Elite HPE-240f failed a few months ago and I finally had time to fixation (rock a Pavilion dm4 laptop in the meantime, I'm not in a huge rush). I replaced it tonight with a Western Digital Blue 1 TB hard drive, which I know is Advanced Format.

  I love HP platform minor changes in the the Windows 7 OS, I went ahead and tried to reinstall the OS of my recovery disks that I made when I got this PC. I checked the BIOS settings and the new hard drive WD IS recognized, the size is correct, etc. It has been configured in RAID with the SATA controller, and I tried to put out when the installation of the operating system initially lacked AHCI. It seems to be stuck in some kind of loop in the final configuration step, and I get out of the dialog box "Installation of Windows set up Windows to run on a hardware on this computer" could not. Hit Okay sends in reboot and after that I get a "Windows is unable to complete the installation. To install Windows on this computer, restart the installation"notice.

  It makes me batty, and I really want my back office. This is a great machine, and as much as I love my laptop, it can't handle heavy programs like Photoshop or my multitasking fool. I managed to get the OS installed by forcing the system to bypass its system predefined through registry commands, but the important things were wrong, as Windows Update does not work, so I'll try to reset all with only recovery disks. So far, no go. I am extremely tired, frustrated, and it's late, so apologies for what I've left out or of typos. Any help on how to solve this problem is GREATLY appreciated.

  Thank you very much for your response, @MechPilot. I actually found what I thought, it's perhaps the question a day or two before your answer: my computer was manufactured and purchased just before October 2010, which has been cut for restoration placed disks shaped for the drives non - Advanced Format. All the following which has been reformatted accordingly. I contacted HP and bought the replacement of the recovery discs (made in 2012), that I received yesterday. After several hours of nerves and finger-crossing, it worked like a charm. The operating system has successfully recovered, and I couldn't be happier!

  I answer computer said of office right now, in fact! Thanks again.

• Windows CD can not find installed hard drives

  I have a PC that has windows XP installed and worked well and I have DSL so I kept it updated. It has been updated for the updates. It was a month that it seemed hung on a windows update and I've finally powered down to exit the update mode. After that, he would finally in XP but would not other that the busy when an icon is clicked. I decided to reload XP using the same CD I used originally when I built PC. It will load the drivers to install XP, but when installing windows is selected it says no hard drives found. When booting 2 HARD disks are displayed, but are not detected when you look in the BIOS. I've tried changes in the BIOS as auto detect HDD including default BIOS and not go. I remembered to change a partition using Partition magic 8.0 and decided that might be the problem, so I started in the magic of partition and formatted part C of the HDD in NTFS, but the results are the same. Any suggestion is appreciated. TIA

  Do you mean you see a message like this?

  Setup did not find any hard drives installed in your computer. Make sure that the hard drives are powered on and properly connected to your computer, and that any hardware configuration of the drives is correct. This may involve a diagnosis provided by the manufacturer or the installer running. Setup cannot continue. To quit Setup, press F3.

  If the disks are not appearing in BIOS, it seems unlikely that XP will be able to see them no more.

  Describe the best you can, your hard disk configuration...  IDE, SATA, SCSI, RAID configurations...

  You build the hardware yourself or is it a system store bought?

  Are you able to determine when the system turns on, the brand and model of your motherboard and the BIOS it is running?

  Without more information, I can only offers these general reflections where to search:

  When you see a message like this, obviously the XP installation starts to load, but then when the installation program needs to go out and find your hard drive is not find the hard drive.  It means not necessarily your hard drive is defective and if it worked before, it's probably still plugged.  It simply means that the installation of XP is not able to find it.

  Looks like you need enter the BIOS on your system by pressing the 'Delete', F2, F10 or F12 key (what the key is good for your system), find the section where the types of hard disks and hard disk interfaces are configured and temporarily change the setting so the XP installation is able to find the hard drive.

  Where to find the accommodation and how to change depends on your system manufacturer and the version of the BIOS, so you end up having to look at her.  If you know your system brand and model, we can probably help you find a job.

  You must locate and change the interface mode to your hard drive in the BIOS so that when installing XP loading, it will be able to locate the hard drive.

  Before making adjustments, you should take note of what are the current BIOS settings, so you can change when you are finished.

  The adjustment varies so here are some examples that I have accumulated:

  The adjustment is done in the BIOS and could be in Integrated Peripherals, Configuration of SATA, SATA Mode device.  After you make the changes, save them and restart your XP installation program.

  If you find that the mode is set on the RAID/SATA mode, change the IDE mode.

  If you find that the mode is set to AHCI, change the ATA mode.

  If you find that the mode is set to AHCI emulation Mode, change the IDE emulation mode.

  If you find that the mode is set to SATA, SATA mode off or change the ATA mode.

  If you find that the mode is set to SATA Native Mode, disable the native SATA Mode.

  If you find that the mode is set on AHCI/RAID Autodetect, change the combination mode.

  If find you the setting that works for you, I would like to know what it is so I can add it to my notes.

  Do, or do not. There is no test.

  I decided to implement the points for a new puppy instead of a pony!

• Pavilion p6110t CTO Desktop: drivers for Windows Server 2008 and HARD drive problems

  Recently, I had the hard drive with my OS failure. After replacing the hard drive and reinstall windows server 2008, I seem to have encountered some problems with drivers.  After insalling Windows, I had 3 items in my device manager that not have installed correctly. I could get the driver for the LAN port to work, but I did not get the driver to "Standard VGA Graphics Adapter" and "SM Bus controller". After a little research, I believe that the graphics card is a Radeon HD4350. With this information, I still have been unable to toinstlal the correct drivers or the other of these elements. I tried several drivers listed on the support page of the drivers on the HP website, but all fo return them the same error of not finding the right operating system. The link to the driver, I used initially on my previous installation seems is no longer valid.

  Also, I can't access two additoinal hard disks (sata connected). They were used with the previous installation of windows without any problem. They appear in the Device Manager but do not show in my computer. A removable disk appears that I don't know what it is. Previously I used the software to mirror one of the disks on the other in order to avoid the loss of data if a disk fails. Is one of the above players with not be able to access the drives causing the problem or the software used before the problem?

  Any help on these questions is greatly appreciated.

  Ok.

  I can't help you with the readers then.  It is out of my area of knowledge.  If they are healthy and active in the disk management utility, then that's all that I know these should be reported.

  As for the graphics drivers...

  Download and install this free utility for files.

  http://www.7-zip.org/

  After installing 7 - zip, right-click on the graphic driver file and select 7 - zip from the list of options.

  Choose 7-zip to extract to: and leave it to unzip the file in a folder.  I have it extracted the file name of the file.

  Then just follow the rest of my instructions to install the driver.

  Of course that you you first go to where 7 - zip extract the folder and continue from there.

• Windows hard drive problem!

  

  Pavilion DV7 7102ea

  I tried to use windows download tool and USB for re - configure windows, it's doesn't work.

  on the other hand, my friend take my hard drive from the laptop, it's even happened that this. We thought it was the problem of hard drive!

  in fact, my night just to October 10, 2013 warranty, what do I do now? Is the hard drive should be of 2 years warranty?

  Can not be solved, but maybe data can be retrieved. His days as a main drive of a computer longer, however. Stop using it. Whenever you try to run the damage worsens. You need get the new drive and install it and put Windows on it and then get an external hard drive (usb) adapter and move the files from the old drive to the new. Chances are most of it is recoverable if you caught the problem early.

• Activation of Windows Vista on a new hard drive problem

  I had to reinstall Vista on my Dell Inspiron 1750, due to a hard drive failure. I was installing a disk hard nine for the first time after having exchanged the defective drive. I have an OEM of Vista Home Premium version and a sticker of activation on the laptop to consider no problem. However when I try to activate Vista using the key on my laptop, I get an error saying that it is already in use. What should I do now?

  You can reactivate your Windows Vista installation by doing the following:

  1. click on the Start button and in the box, type search: slui.exe 4

  2. press the Enter key on your keyboard.

  3 select your country.

  4 follow the instructions for the activation of the telephone (toll-free).

  Carey Frisch