2 internet connection teminated to ASA 5512

Similar Questions

• Internet connection ASA 5512

  Hello

  I am new to networking and I have a framework problem 5512 ASA firewall. The problem is that I can not configure the internet connection inside my network.

  I created both LAN and WAN interfaces with the public IP (security level 0) with the ip address of 192.168.35.4, the security level 100. In fact, we replace the old router, and should take its address. I added 0\0 static route for my default gateway, and I am able to ping Google DNS server for the router, but impossible to the computer on the network. The network switch is also present on 192.168.35.254.

  For the purposes of the test, I changed the WAN IP address to computer connected to it with IP 192.168.99.2 192.168.99.1, and when I try to ping to the LAN interface, it does not return a ping.

  I'd appreciate any help.

  I thinl it's your acl global_access.

  You have not applied to an interface with the access-group command.

  If it applies to all interfaces that includes the LAN interface as well as the WAN interface.

  Then add ICMP in there or remove the acl if you want the apply to all interfaces.

  Jon

• Internet connections ASA 5505 - two

  Is Hi possible to configure an ASA 5505 with two internet connections? One dedicated to the VPN and the other for Internet access only.

  If you have an example to share.

  Thank you very much

  David

  I see that you have a static route to 186.125.164.178, if you only test card crypto 2, right?

  Your nat (inside) 0 uses ACL inside_nat0_outbound_1 which doesn't seem to have the exclusion for 10.5.3.0/24 remote network.

• ASA 5510 VPN dedicated Internet connection

  I have a 5510 ASA with a second internet connection on his way.  I would like to have an internet connection dedicated to my VPN Site to Site traffic and the other left to manage the public internet traffic.   I know that I can do this with a static route, but today, I noticed the "tunnel" option  How exactly does the tunnel option work mode and it works better for my situation?

  Rob,

  (Simplification) "Tunnel" option tells what to do with traffic, once it has been for example inbound VPN decapsulted.

  In your case, static routes for remote tunnel endpoint + RRI points will do.

  M.

  Edit: I would advise yo forget about the end of the dynamics of peers (dynamic IP L2L or ezvpn) solutions on any interface that does not have a default route on this subject.

• No Internet connectivity with ASA 5505 VPN remote access

  Hello

  I configured ASA 5505 for remote access VPN to allow a remote user to connect to the Remote LAN officce. VPN works well, users can access Office Resource of LAN with sahred etc., but once they have connected to the VPN, they are unable to browse the internet?

  Internet navigation stop working as soon as their customer VPN connect with ASA 5505 t, once they are disconnected from VPN, once again they can browse the internet.

  Not ASA 5505 blocking browsing the internet for users of VPN? Is there anything else that I need congfure to ensure that VPN users can browse the internet?

  I have to configure Split Tunnleing, NATing or routing for VPN users? or something else.

  Thank you very much for you help.

  Concerning

  Salman

  Salman

  What you run into is a default behavior of the ASA in which she will not route traffic back on the same interface on which he arrived. So if the VPN traffic arrived on the external interface the ASA does not want to send back on the external interface for Internet access.

  You have at least 2 options:

  -You can configure split tunneling, as you mention, and this would surf the Internet to continue during the use of VPN.

  -You can set an option on the ASA to allow traffic back on the same interface (this is sometimes called crossed). Use the command

  permit same-security-traffic intra-interface

  HTH

  Rick

• ASA 5512 different route by VPN Group (VRF as feature?)

  Hello

  Here's what I'm trying to do.  I have a Nexus 7000 with several of the VRF, simplicity lets call it A VRF, VRF B, VRF C. VRF A simulates a network of management and VRF B and C are customer environments.  VRF B and C VRF will be overlap of intellectual property.  I have a 5512 ASA I use VPN in the environment, it also provides internet access for applications that run in A VRF, (VRF B and C do not require internet access).  What I want to do is to implement three different access VPN on the SAA even, where some users will have VPN 1 group policy and have access to the VRF has, but should not have access to the VRF B or C, same VPN 2 should have access to the VRF B and 3 C VRF VPN.

  My original intent was to configure the ASA with 0/0 to internet Gig, Gig 0/1 A VRF and then Gig 0/2 sub interfaced so 0/2.10 is 10.10.10.1 in VLAN 101 that connects VRF B, 0/2.11 concert would be 10.10.10.1 in 102 VLAN that connects to VRF C.  However, better than I can tell ASA 5512 is not aware of VRF (or is it just a separate license, I would need?) and as such, it is not possible.

  Next similar reflection, but instad configure as 0/2.10 is 10.10.10.1 in VLAN 101 that connects VRF B, 0/2.11 concert would be 10.10.11.1 in 102 VLAN that connects to VRF C. However, I throw it here, issues as the VPN 2 and 3 need access to devices with the same IP address, which is even better I can tell, the ASA is not able to make Policy based routing.

  Is there another way to do this? Is there something that I am on?
  I need to make sure that the 2A VPN users can access services available in the VRF B, they should not have the ability to access (intentionally or not) services on VRF A or C, nor the users VPN 1 or 3.

  I have also a 5585 ASA w / context multi license, I can then creates a context by VRF (that I have), I then interfaces in each correct the VRF-related context.  However, I do not think that I can terminate VPN here, best I can tell when in multi-contexte mode you can not have VPN license.

  Your research led you to conclude correctly that the ASA is neither compatible with VRF nor can it be based on routing strategies. Also, you cannot terminate remote access VPN on an ASA multi-contexte.

  Doing what you ask a single AAS is a bit problematic. If you had a unique internal addresses, the subinterfaces would work fine.

  Because it looks like you have a virtualization infrastructure, have you considered using the low cost ASAv? You could run multiple instances, one per VRF. Everyone knows only the public address space and its respective assocated VRF.

• VPN remote as well as Internet connection

  Hello

  We have a Cisco ASA 5512 - X & we have configured the VPN Site to Site (IPsec Tunnel) as well as the distance of Cisco vpn client. Both work correctly.

  problem is that:

  When the remote user vpn client connection, then they are able to access the local corporate network but is not able to access the internet on their local computer.

  I want that, when the user connects client remote vpn as well as its local internet.

  Kindly, help us do.

  Current configuration is attached.

  network object obj - 10.90.5.0
  10.90.5.0 subnet 255.255.255.0

  NAT (inside, outside) source static obj - 192.168.0.0 obj - 192.168.0.0 destination static obj - 10.90.5.0 obj - 10.90.5.0 no-proxy-arp-search to itinerary

  IP local pool testpool 10.90.5.1 - 10.90.5.100 mask 255.255.255.0

  Crypto ipsec transform-set esp-3des esp-md5-hmac ikev1 us_3des
  crypto dynamic-map 1 HOUR set transform-set us_3des ikev1
  card crypto CVPN 1-isakmp ipsec dynamic PRIVATE
  CVPN outside crypto map interface

  IKEv1 crypto policy 1
  preshared authentication
  3des encryption
  md5 hash
  Group 2
  life 86400

  tunnel-group usnlgroup type ipsec-ra
  tunnel-group usnlgroup General-attributes
  address testpool pool
  usnlgroup group of tunnel ipsec-attributes
  IKEv1 pre-shared-key *.

  vinod username password *.

  If the PC loses internet after connecting to the VPN while it must in tunnel-like split-tunnel-politics.

  From your configuration, I see that there is no group configured on the tunnel-group strategy.

  To activate the split tunnel you can use the configuration below

  Note the subnets that you allow on the VPN client. Outside these subnets all other traffic will use local circuit of the internet from your PC.

  Split_Tunnel_List list of standard access allowed

  internal usnlgroup group policy
  attributes of the strategy of group usnlgroup
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list Split_Tunnel_List

  tunnel-group usnlgroup General-attributes

  Group Policy - by default-usnlgroup

  Reconnect the VPN and then try to access the internet.

• Cisco 2911 and ASA 5512 remove double NAT

  Greetings,

  I have 2 subnets on Cisco 2911 router

  192.168.3.0/24 and 192.168.1.0/24

  3rd network 192.168.4.0/24 is natting internal interface to the modem for internet access. creating 2 NAT (NAT in router) and NAT in Modem

  I just bought Cisco ASA 5512, no chance I could remove the Cisco 2911 router NAT and set the default gateway for Cisco ASA?

  Yes you are right...

  You must ensure that you get the routed LAN traffioc to hit inside the interface ASA in ASA, you can do PAT/NAT to access...

  Concerning

  Knockaert

• Remote site 2 Internet connections...

  I have a remote office that currently connects to a data center Central via the VPN Site to Site.  I get a 2nd internet connection like a fall back to the remote desktop.  How to configure the Site to Site VPN working properly so that if the main internet connection goes down, the site switches to the secondary?

  On internet connections remotely come from different providers so that they have completely different blocks of public IP addresses.

  Central

  ASA 5520 8.0 (4)

  GIG 0/0 public IP

  Remote

  ASA 5520 8.4 (1)

  GIG 0/0 public IP

  Public IP address of concert 0/3 (2nd internet)

  On the end of HQ you must enter the new IP address of the ISP (for the remote site) as secondary peer.

  On the remote end, you must add SLA so that traffic will be redirected on the second link incase of primary failure.

  Search the forum you will find many Ref assignment to this scenario. Here is one...

  https://supportforums.Cisco.com/message/3452739#3452739

  HTH

  MS

• No internet connection when hotspotshield connects

  When I connect to the Hotspot Shield VPN elite, my WIFI internet connection stops working.

  I use a Macbook Pro.

  Help, please

  Start here: https://support.hotspotshield.com/hc/en-us

• Why safari does say "the internet connection appears to be offline" even though I have a good internet connection

  We have a website that queries a particular web service on the web every 5 seconds. On an iPhone 6 running IOS 9.3.5. I have a pretty good internet connection. But sometimes I get the error message saying "the internet connection appears to be offline. Once I update my page, everything seems to work very well. It is originally the site to behave strangely sometimes.

  Hello

  Tap Settings > Safari then slide downwards and press: clear the history and data from the Web site and then restart your iPhone.

  See if that makes a difference.

• Why Siri requires an internet connection to work properly?

  Why Siri requires an internet connection to work properly?

  Because his answers do not come from phone, they come from Apple servers. This article can help.

  Use Siri on your iPhone, iPad or iPod touch - Apple Support

• Internet connection no longer works unless I have disconnect and reconnect the wifi regularly

  I find that after a time random, maybe twenty minutes a half an hour or so, my internet connection breaks down and it can only be fixed by disconnecting and reconnecting to my wifi network.

  It is a problem on my iMac of retina 2014 running El Capitan and 2011 MacBook Air my wife running Mountain Lion (but not on my MacBook Air of 2011 which takes place in Yosemite).

  It does not seem to be triggered by almost anything, but it's maddening to have to do all the time. It's a router NetGear btw, less than a year.

  If anyone has a solution I'd love to hear it!

  Greetings, peederjigson!

  Welcome to the communities of Apple Support! It seems you have some problems to stay connected to the Wi - Fi on some of your devices. This is not how it is supposed to work so I'll be happy to help you.

  Use the Diagnostics wireless for you help to solve the problems of Wi-Fi on your Mac - even with a new router, the firmware may need to be updated. But this article can go a long way to point out where it is.

  The potential of Wi-Fi and Bluetooth interference sources - because this is not the case with all your devices, it could be other things blocking the signal. Here are a few potential sources.

  Recommended settings for the WiFi routers and access points - because your router is "-ish" make sure that the settings are correct.

  Have a great day!

• How to switch to safari 9.1 without internet connection

  I've recently upgraded to El Capitan on my 2009 mac. Fine, except that now, I find my version of safari (6.6) is not compatible with El Capitan and I have no internet connection. How to switch to safari 9.1 without being able to download it? Can I get a disk with on or something?

  Safari is upgraded when you upgrade your system. There is no installer for stand-alone for Safari. If you run El Capitan your Safari should be version 9.1.2. Otherwise apply the OS X Combo Update 10.11.6.

  The Combo update is a complete installation, as opposed to an incremental "delta" update, so you have to overwrite all files are damaged or missing. It does not matter if you have previously applied. All your data and settings must be kept, but that said, you should always have a backup.

  https://support.Apple.com/downloads/MacOS

• How to locate an iPhone even without an internet connection?

  Let's say that my iPhone was stolen, then the thief off the internet via Wi - Fi or data connection cell, does that mean there is no internet connection on this phone but location services is always on. I would still be able to find that the iPhone?

  N °