2 new physical disks with no status critical yellow exclamation Point

Similar Questions

• Expand a virtual disk with new physical disks?

  Hello people,

  Pleas in law not to shoot me to ask what I fear it may have already answered somewhere and my research is poor and as still not turned up the answer.

  I'm relatively new to VMware, previous job was especially MS Hyper-V and is always to some extent.

  Hower to the point in question, I have a single host (VMware ESXi 5.0.0) with a single server VMware 2008R2 on her guest and the C: drive is quickly running out of space. The existing, aligned hard disk virtual hard disk has 10 GB free to extend the ramdisk with.

  Therefore, my thoughts are I might add an another one or two new physical disks and add them to the data store that is aligned with the virtual C:\drive to the comment server, I would then be able to extend the exisitng C:\ virtual hard disk with the new ability to drive two new physical drives added?

  Hope this sense makses, hoing it's okay and I get out of jail!

  Thank you very much

  Graeme

  Hello

  Please see this link because it deals with the procedure to enlarge a vmdk and extend partition in comments

  First enlarge the data store after the addition of physical drives. Select the data store, properties, increase and the LUN detected.

  Then use the vmkfstools as explained in the video to develop

  http://blogs.VMware.com/kb/2010/02/how-to-expand-a-VMDK-and-extend-a-partition-in-for-VMware-ESX.html

• Satellite l.660-12 q - would the recovery disk rebuild the new HARD disk with a new recovery partition

  Talk about confusion. Does anyone know how to get a Toshiba C660 work after the HARD drive failed and the owner has stupidly NOT followed the instructions to make a recovery disk. Will be the recovery disk (if buy you one from Toshiba) rebuild the new HARD disk with a new recovery partition and install windows 7 (original OS) and accept the product key printed on the Windows license, attached to the base of the laptop. I have read a number of suggestions, but these have been considered incorrect by others.

  Surely, Toshiba must have a way to sort this problem.

  They read these messages?

  Hey Buddy

  I don't think it's really complicated, that I could find all the information about the recovery procedure in the user's manual

  The recovery disk must be created on the first day of purchase its recommended to create one in case something would be wrong with the HARD drive.

  The recovery disk contains an image. The image is a package containing Win system, drivers, tools and all the stuff pre-installed on the notebook.
  You bought the laptop and the system has already been activated so that you have need of t the key placed at the bottom of the unit.
  In addition, the use of the recovery disc formats the drive HARD integer (partitions too) and set the laptop in the same condition as at the first day of the purchase.

  There is also another option to recover the notebook called HARD drive recovery. This HARD drive recovery requires no recovery disk. The recovery disc HARD would be to use format ONLY partition C (System).

• Satellite Pro A300-22F - WLAN is listed with a yellow exclamation point

  I just bought an A300-22nd.
  WIFI does not work - in Device Manager the conroller of network (under 'other devices') has an excalamation mark on it - the problem is not installed driver.

  Laptop came with a sheet of additive of toshiba on problems with wireless connectivity - which goes through how to install the driver. Two problems - the leaflet is reserved to L300 L300D and copying is of such poor quality that I can't read the instructions!

  I know that this phone has WLAN (a, d, g and draft n), and it has a switch for him - what is on and lights up.

  At the moment I am connected to the router broadband - not much use as my PC is at the front desk even - I need a wireless connectivity!

  Help!

  Hello!

  On the Toshiba site, you can download all the drivers for your laptop and so he should t be a problem to solve this yellow exclamation point:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  Download the driver the most recent and that s it! :)

  In addition, WLAN connectivity can be enabled using the hardware on the laptop switch * and * if you press FN + F8.

  Good bye

• Basic with yellow exclamation point features

  Hello

  My L412 supplied with Windows 7 Home Premium. I reinstalled Windows using a purchased Windows 7 ultimate DVD and I installed most of the software, but I still 3 devices basic system with yellow exclamation points on them.

  Here is a screenshot

  http://Tinypic.com/r/28j9loy/7

  Any ideas on how to fix?

  Try the driver of lenovo card reader

  http://www-307.IBM.com/PC/support/site.WSS/document.do?lndocid=MIGR-75277

• In devices and printers, I have an icon for a laptop with a yellow exclamation point. I have a desktop computer and remove this icon of the laptop.

  A laptop once was connected to my desktop via USB cable PC; It belonged to me.  The owner wants to access its database of the company, but in vain.

  Now, in devices and printers, I have a laptop icon that is not one of my devices, but the Device Manager lists in "Other devices" with a (USB) universal serial bus controller, which is also included in the icon of the computer laptop properties under the material.  The yellow exclamation point is for troubleshooting.  The problem is: I do not own a laptop device.

  I want to remove the icon of the laptop and its inscriptions, including the (USB) universal serial bus controller.  Both are marked by a yellow exclamation point, but, of course, they do not work because they do not exist.  But this icon of the laptop has name my PC on it.

  My desktop PC should not be listed in devices and printers, does it?

  Hello.

  Open devices and printers right click on the device - remove the instrument.

• Point of "Unknown device" in Device Manager with yellow exclamation point

  I have a VGN-FW170J laptop.  My poster an "unknown device" Device Manager with a yellow exclamation point next to it. indicates that the driver is not installed for this device.  How to solve the problem?  Sony Firmware Extension Parser device driver "" SODFEP-00270203-0083. "." EXE"what to fix this problem, BUT NOT compatible with my computer.  Need a solution

  Hey there GEP170!

  Please provide additional information about your question. This camera is connected to your computer? To check if this feature is one that is being indicated by the Device Manager, you can try to uninstall this device. If this device still appears in Device Manager, it only means it could be another device.

  Please post here, what happens if you uninstall this device.

  Thank you

  ~ Tim

• Add a new virtual disk to a very critical existing VM

  Hi all,

  My question is very simple. I have to add a new virtual disk to an existing Windows Server 2008 Standard virtual machine (we use vSphere 5). This machine

  is very critical, because it is the server of the company files. Is there a risk to add the new virtual disk on the virtual computer? Is it better to add it with the virtual machine died, or can I also in the virtual machine running without risk? I tried with a virtual test machine and everything works fine and I know to be very paranoid, but in this moment I still feel a great responsibility on me.

  Thank you all.

  There is nothing wrong by adding a disk to a virtual machine, it is HOT add, that is the advantage of the SCSI layer. VMDK all use a virtual scsi controller and it is hot add capable. SO just, add it and partition.

• Physical disk with VMPlayer?

  I just downloaded and installed VM Player on a Windows 7 computer.

  I'm trying to get him a physical disk that has Windows XP on it, but I don't see a setting in the drive of the VM to do this.

  Did I miss something or I need to upgrade to the full version?

  Thanks in advance.

  Am I missing something

  When you add a hard drive of the virtual machine, you must select "Use a physical disk (for advanced users)" and note the last part "(pour les utilisateurs expérimentés) '!"

  You must also at least remove the drive letter for drive in Windows 7, before she mounts to VMware Player.

  or I have to upgrade to the full version?

  VMware Player, either for Windows or Linux, is a full version of himself he and does not come in versions of function of different type in itself.

• Minor problem with the New Installation of Windows 7 on my Inspiron E1705/9400 - two entries for "Base system device" under "Other devices" with yellow exclamation point

  Hello

  First of all, let me tell you about my system.   It is of a laptop Inspiron E1705/9400 with the Core 2 Duo T7400 processor clocked at 2.16 GHZ.   It has 2 GB of RAM and a hard drive on the Hitachi Travelstar nine 500 GB (7200 RPM).   It also has the GeForce Go 7900 GS video card.    Previously, it had Windows XP Professional (32 bit) and worked well.   But, I have three computers in my home and Home Office and would they work better together on my wired home network, so I'm upgrading all three to Windows 7.   My two desktops (a Dimension XPS 420 and the other Dimension XPS 430) seem like they will be no problem to upgrade to Windows 7.   But, this laptop was not on the list of Dell Windows 7 compatibility.   However, the Windows 7 Upgrade Advisor that I have downloaded and run seemed to say that it was OK to do a clean install of Windows 7 32-bit and he had only a few minor issues, where it says search the drivers updated from the manufacturer.   Initially, the laptop came with a 100 GB hard drive.   For my use, which becomes very small, so I decided to get the exact same 7200 RPM drive 500 GB size.   This will allow me to do a clean install of the 32 bit Windows 7 OS on the new hard drive and not have to wipe the old disk to do so.   I can just keep the old HD and paste it back whenever I need to get something out of it.

  So, here's my minor problem.   After the transfer of some elements off the coast of the old hard drive, I installed the new 500 GB drive and installed a cleaning of the 32-bit version of Windows 7.    I'm happy to announce that I have not had virtually no problems with installation and everything seems to work fine.   He seems a little more zippy than before and I have not met so far that doesn't seem to work.   I went through most of features and almost everything is superb.   But there is a minor problem, showing in Device Manager.   At least, I think it's a minor problem, but maybe someone can give me feedback to know if she is or not.

  In the Device Manager list, there is a category called "other devices" now and the icon shows a little white circle with an exclamation mark.    When you expand this category, you see two identical entries that say "Base system device" and the icon has a yellow circle with an exclamation mark inside.     I know from experience that it is not a good thing to see items in the device manager that have a yellow circle with an exclamation point.   I clicked on both of them and neither one really tells you what the device is, or who did what is site you would go to a driver.    On the general tab, it has the following information:

  -Device type Other devices

  Reference of the manufacturer- Unknown

                       Location     -         Bus PCI 3, device 1, function 3

  
  

  Under device status, it says the following:

                         The drivers for this device are not installed. (Code 28)

  There is no driver selected for the item or a set of device information

  To find a driver for this device, click Update driver.

  Each of the entries seem to be almost the same thing... but not exactly.   The other has the location

  list PCI Bus 3, device 1, function 2... instead of function 1.   This seems to be the only difference.

  I tried the button to update the driver, but that doesn't seem to work.   No matter if you say it looks like your

  computer or to look for a new driver from the internet, it does not find anything.     As I said at the beginning,

  the system seems to work very well... but, given that I don't know what this device is or does, I might be missing something.

  He drives me crazy just have these yellow circles with exclamation point hanging out in my device manager.

  I could really use some help here.    Any ideas or help would be greatly appreciated.

  Thank you

  Bryan Ray (Richmond, WILL)

  BTW, I just downloaded and installed the driver pack from this ftp location and it worked, even for Windows 8.1 - 64 bit.

  Thanks Steve!

  Roger

• T61 - no sound - Audio on High Definition Audio Bus with yellow exclamation point device

  Hello

  I don't know when it started, but suddenly my T61 has no audio/HiFi. I checked the Device Manager and saw the device on High Definition Audio Bus Audio with question mark (large) yellow with yellow exclamation superimposed on it. On Lenovo's Support site, I downloaded the 7ka114ww.exe, hoping to remedy this device to uninstall it reboot and re - install using the downloaded exe, but anything will do.

  Any suggestion or help is really appreciated. Thanks in advance

  PS. I also see the basic pop up system device after a reboot and ask to be installed? This pop-up had been there for some time before the sound/sound has been lost.

  Hi and welcome to the forum!

  What operating system do you use?

  When you say that you have installed the driver, do you also go to C:/drivers /... to run the .exe steup? The second Setup program must be run to install the driver correctly.

  Base system device is the card reader, to find the driver for your OS here:- http://www-307.ibm.com/pc/support/site.wss/migr-67853.html

  Kee we posted.

• loss of internet connection on windows 7 pro 64. Says connected but no internet access with yellow exclamation point! Help, please!

  I keep losing internet connection, I have windows 7 and every time I connect it to the wireless internet works for 5 minutes, then a little ytellow icon pop up and say its connected without internet access. Its happened to me before and recently started happening to my cpu. I did a FRESH install of windows to see if it can help, but it didn't. IM literally on the point of throwing my processor through the cause of wall, I can't find a solution to this anywhere. Whenever the yellow icon pops up that I have troubleshoot and it indicates the default gateway was unavailable and that fixed it, then I have internet again for about 2-5 minutes and it does the same thing. Ive never had this problem on my cpu and the network has not been changed or anything, so I don't know what that the * could cause this. I literally wiped everything on my cpu and then do a system image to restore too. Ive been messing around with the registry, deletion of things here and there missions that I read, but only thing that happens is losing internet alltogether and must restore from system image. I'm really running out of ideas. Help, please. I have an adapter netgear wn311b wireless pci-express with the latest drivers.

  to detect new updates for network based components on intel:

  http://www.Intel.com/p/en_US/support/detect/?IID=subhdr+dnlds_detect

  You will be asked to download and install active x components.

  After the installation of the small file, click on the "expand all" button

  You can choose to update your components wired network if necessary.

  then re-install your wireless network management software.

  assuming that your wireless network is intact (connected, permits), you can surf the net.

  If the problem persists, troubleshoot more away:

  When the computer is turned off, set again you netgear pci wireless adapter.

  set of antenna for optimal orientation.

  Check if your computer is authorized by your wireless router.

  check the signal strength of your wireless router and the wireless pci adapter.

• Qosmio F30-112: CONTROLLER of BUS SM with yellow exclamation point

  Hello

  Recently I reformat my win pc XP MC using the recovery CD, but I saw on the Device Manager CONTROLLER of BUS SM is to have yellow question mark.
  How could I solve this problem?

  Some time my pc froze (work stoppage) so I have to restart my pc.
  Is it because of the sm bus controller? I try to click on update, but there is a message (the hardware was not installed because the wizard cannot find the necessary software)

  An organization can guide me how to fix it?

  Thank you
  rtmasagca

  Hello

  In your case, I would recommend to day/reinstall the driver!
  F30 - 112 is a part of the PQF30E series.

  SM bus controller can be the SD card reader.
  That's why I recommend that you download the Texas Instruments Flash Media Driver v 2.0.0.4 Toshiba page pilot European and install it again.

  Welcome them

• I get an error of writeback failed after receiving updates or get new files yellow exclamation point in the icon 'son to the right of the screen.

  I must also click DELETE to restart the computer to retrieve the screen and the screen will show also 8-10 writing failure before going to the browser

  What update, the exclamation yellow on which icon, any error message.

  error message in Event Viewer can help.
  http://help.artaro.EU/index.php/Windows-XP/essential-administration-XP/Event-Viewer-XP.html

• Create new physical Link using RIDC element

  How to bind the new physical element with electronic document existing RIDC?

  Service, I used is CREATE_EXTERNAL_ITEM and it just to create a new physical element.

  What parameters are necessary for the creation of link?

  IdcClient client = getUCMConnection();

  DataBinder dataBinder = client.createBinder ();

  HdaBinderSerializer serializer = new HdaBinderSerializer ("UTF-8", client.getDataFactory ());

  dataBinder.putLocal ("IdcService", "CREATE_EXTERNAL_ITEM");

  dataBinder.putLocal ("dSource", "Physical");

  dataBinder.putLocal ("dSecurityGroup", "Public");

  dataBinder.putLocal ("xCategoryID", "one_day_disposition");

  dataBinder.putLocal ("dDocType", "Document");

  dataBinder.putLocal ("dDocTitle", "Test Example9");

  dataBinder.putLocal ("xAddLinkList", "CS:1:0:wwRenditionsCheckinName::");

  dataBinder.putLocal ("xLinkTypeValue", "1:0:wwRenditionsCheckinName");

  UserContext IdcContext = new IdcContext ("username");

  ServiceResponse response = client.sendRequest (userContext, dataBinder);

  DataBinder responseData = response.getResponseAsBinder ();

  }

  Try this code. It will create a new physical item and set it as "Renditions" relationship to an existing electronic record on the server.

  Thank you

  Srinath