2012 R2 cluster without RDM

Similar Questions

• Migrate virtual machines from HP G7(single host) for HP G8 (Cluster) without shared storage

  Hello

  I have 2 esxi host (hp dl 380 G8) and put them in a cluster and other host esxi (dl 380 g7) and I have no shared storage and use local disks just now I must spend my VM G7 server a cluster of the G8 but I want to know I can join my cluster g8 g7 and migrate web vmware machines without any downtime?

  I want to know can migrate without downtime with localdisk? I have no shared storage

  Best regards

  BAbak

  can I join g7 to my cluster of the g8

  You can mix into clusters hosts all desired, even Intel and AMD at least that you enable EVC on the cluster (of course, HA or DRS require shared storage compatible/CPU). However, you need not to have even just cluster hosts to migrate virtual machines through vMotion between them.

  migrate web vmware machines without any downtime?

  Don't know what this "web vmware' but yes, because ESXi 5.1, you can use"enhanced vMotion"to live migrate virtual machines without service interruption from one host to another, even without shared storage:

  Migration with vMotion in environments without shared storage

  The usual vMotion requirements apply. Also you can only live migrate virtual machines from the old host to the new hosts because of different generations of CPU (and back as long as you don't have bike powered virtual machines on new hosts).

• Ripping a 4.1 host in a new 5.5 Cluster WITHOUT access 4.1 vCenter Server

  I have a client who has his 2 4.1 vSphere hosts in a cluster of vCenter 4.1 which is NOT under its control or access. vCenter server access is with a 3rd party that he is nervous on his account supported by a new provider. I'm looking for the safest method (preferable without interruption) to import these 2 hosts into a whole new vSphere 5.5 cluster with 2 new hosts and vCenter 5.5 server. He has access to individual hosts via the vSphere Client as well as its local based NAS storage where the virtual machine of the resident. The end result is vMotion and Storage vMotion, virtual machine on the new guests and new storage without interruption then remove the old hosts.

  This is possible without any downtime of the virtual machine. However, as you deploy new fresh vCenter again, you will need to reconfigure settings HA/DRS. Also, since you have no control over the old vCenter, given old vCenter performance you can't as well. If you don't care about performance data, you're good to go.

  Here's how you can make this migration:

  1. deploy the new vCenter: for your condition: vCenter device will work just fine: reference:http://www.virten.net/2013/09/vmware-vcenter-server-appliance-5-5-vcsa-limitations/

  2. create the cluster on new vCenter, set up the same.  first add your new ESXi 5.5 clustered host. Make sure that the shared on the old host ESXi storage is visible on the new host as well. If it is not possible, you can run without shared as well storage vMotion. Reference:VMware vSphere 5.1

  3. now you can add your old webhost to the new cluster, make sure that vMotion requirement are already configured:

  Documentation Centre of vSphere 5.5

  4. Add your old host to new cluster. Once you add these ESXi host in new vCenter, both will be disconnected automatically old vCenter. If your host processors are different, you must enable EVC: make sure you understand impact of the VCA, the same configuration.

  Reference: VMware vSphere 5.1

  VMware KB: Enhanced vMotion compatibility (EVC) support processor

  VMware KB: EVC and CPU compatibility FAQ

  VMware KB: Activation CVS on a cluster when vCenter Server is running in a virtual machine

  5. you can migrate your old Web host VMs to new host, once the migration is complete, you can keep your old Web host in maintenance mode and remove the same.

• Disk shared across hostsystems without RDM

  Hi all

  We use

  vSphere 4.0 U1 and I would like to set up a frontend with Linux cluster

  for one of our applications. That's why we need the capability of

  share a drive between two different VMs on two systems of different hosts.

  I found a book "Setup for Failover Clustering and Microsoft

  The cluster Service"which covers the subject of shared disk. Is it possible

  share a file of common instead drive a RDM LUN?

  There is also a KB

  Article:

  http://KB.VMware.com/selfservice/microsites/search.do?cmd=displayKC & docType = kc & externalId = 1002782 & sliceId = 1 & docTypeID = DT_KB_1_1 & dialogID = 83230062 & StateID = 0% 200% 2095753095

  Unfortunately, it does not give much information.

  Thank you

  your help.

  Hello

  If the VM disk is a clustered file system and that a clustered file system then it is perhaps possible to do what you want but only on a single host. In general, however, it is alleged that you use RDM to solve this particular problem, such as the blocking of VMFS does not come into play.

  The question that is below this, the ESX host running the VM locks write access to these blocks of storage in a given host. This allows to reduce the problems blocking and SCSI reservation conflicts. They are reserved only for this host. So if another host tries to access a drive that is already used by another host, that it will not work as the blocks on that VMFS are reserved for the first host that is running the virtual computer. When you use a RDM is NOT the case, as the WDR don't use VMFS but just present as a LUN.

  Another option is to have a VSA as the Celerra VSA, OpenFiler, FreeNAS iSCSI, etc. serve clustered volumes to each of the nodes in the cluster. This way you don't need a RDM.

  It is the nature of VMware ESX/ESXi locking and mechanisms to reduce the amount of scsi reservation conflicts.

  Best regards
  Edward L. Haletky VMware communities user moderator, VMware vExpert 2009, 2010

  Now available: url = http://www.astroarch.com/wiki/index.php/VMware_Virtual_Infrastructure_Security'VMware vSphere (TM) and Virtual Infrastructure Security' [/ URL]

  Also available url = http://www.astroarch.com/wiki/index.php/VMWare_ESX_Server_in_the_Enterprise"VMWare ESX Server in the enterprise" [url]

  Blogs: url = http://www.virtualizationpractice.comvirtualization practice [/ URL] | URL = http://www.astroarch.com/blog Blue Gears [url] | URL = http://itknowledgeexchange.techtarget.com/virtualization-pro/ TechTarget [url] | URL = http://www.networkworld.com/community/haletky Global network [url]

  Podcast: url = http://www.astroarch.com/wiki/index.php/Virtualization_Security_Round_Table_Podcastvirtualization security Table round Podcast [url] | Twitter: url = http://www.twitter.com/TexiwillTexiwll [/ URL]

• Add an element to a cluster without updating all users of the cluster

  I have a cluster that is sent to many different vi. Whenever I have added to this cluster, I need to change every vi that uses it to fix the various controls of input terminals and ungroup by names.

  I'm not change or remove existing items in the source cluster. just to add another element that one worries of the vi "shipwreck" for others, it is simply one don't care. Is it possible to avoid having to fix each "sink" vi when I do this? I would only need to update the vi that uses the new element (which of course, I do anyway).

  In C, I can update, add a member to a typedef'd struct and everything is fine - no problems; How can I do something similar in LV?

  If you branch out a cluster then all sinks must be the same. You should do your cluster a typedef and use the typedef on your screws in this way that you change only one place. Even with the a typedef in C.

  LabVIEW manual contains instructions on how to create and use of typedefs.

• Events unregistering on a cluster without Unregistering for all dynamic events

  Hello everyone

  I've been playing with dynamic event record but I hit a problem.

  Normally if I want to stop triggering events on a single control I will be wire constant ref with the correct type in the registry for block of events. This means that I don't have to use the unregister for events block and then rebuild the entire events list to registry when I only want to stop the events on a control.

  However, if I try to bring together a group of the refs (which cannot necessarily be of the same type) in a cluster then I can no longer cancel the events on this cluster registration from the register of events work a group of control constants.

  An alternative would be to use an array instead of a cluster, but this has two disadvantages: it does not create a case of dynamic event for each Member of the array and all controls must be the same type or they are co-erced to a more generic control class.

  I've attached an example VI (labVIEW 2011 SP1)

  I think I finally get the problem now.

  You need feed two references in separately.  You can cluster the registry OUT for events, I know, but I don't think that what you want will work.  You know that you can enter the tables in a table instead of a cluster, right?

  Shane.

  PS to be clearer.

  Register to activate your button separately from the rest.  Save all your "to be marketed" references - individually, not clustered - in a second 'register to events' and then together the two outputs (with the Save refnums event) before passing into the structure of the event.  You might have what you want.  So big cluster AFTER signing up, not before.

• Essbase cluster without stopping

  Hello

  I have implemented an active-passive cluster of Essbase via OPMN with (restart death = false) on v11.1.2.3.506

  However when I want to stop the Essbase agent on the Active Server using stopall opmnctl, the Essbase agent stops but then it starts on the passive server!

  So, I have to perform stopall opmnctl firstly on the passive server then on the Active Server to stop Essbase.

  = > Is this the right way? Since this is the user requesting the closure, it is not as a failure?

  Kind regards!

  Hello

  Go through the links below can useful

  1) Hyperion Essbase clustering on Linux

  2) Hyperion Essbase clustering on Linux

  Thank you

  Pratik

• VMotion of a HA cluster to another cluster without storage shared

  I was trying to vmotion that two hosts and clusters of data from a virtual computer store between HA (no shared storage). Web client gives me this warning, but the migration is successful.

  The warning message is:

  If this is done, the virtual machine will lose vSphere HA protection. If you proceed with this operation and it completes successfully, vSphere HA not will try to restart the virtual machine after a subsequent failure. vSphere HA protection is restored when network partitions or disk accessibility problems are solved.

  Is this a problem?

  given that your VM left cluster HA, warning to inform you that VM is not going to be protected by HA.

  If your target cluster where you moved your VM is also active HA then he will protect even by HA in this cluster.

  In short, this warning is more to inform you that your VM leaves HA protection. as long as you know what you do, no problems.

• How to install BDE cluster without software

  BDE 2.1, it is established that you can create a cluster hosts and let distribution management software (for example Ambari) install the cluster.

  We are looking to upgrade to 2.1, but for now on 2.0.  Is it possible to just create the virtual machine and then install the cluster of Ambari?  We tried to install the cluster, remove the software (RPM - clear), then by restarting the guests.  It seems that the BDE reinstalls the software when this happens.

  It is not the end of the world if we can not, as I said, let's go to 2.1 next week.  However, what I have above possible?

     Create a Cluster of basic with the Serengeti command-line Interface

  Yes, you can use BDE 2.0 or 2.1 to create a basic cluster in your environment of Serengeti. A basic cluster is a group of virtual machines configured and managed by Serengeti. Serengeti helps you plan and configure the virtual machines according to your specifications. You can use virtual machines to the cluster basis to install large data applications.

  The basic cluster does not install application of large data files used when you create a cluster Hadoop and HBase. Instead, you can install and manage applications data with tools for third-party such as Apache Ambari application or Cloudera Manager management in your environment of large Extensions of data and integrate with your Hadoop software. The basic cluster does not deploy a cluster Hadoop and Hbase. You must deploy software in virtual machines from the base of the cluster by using a third-party external application management tool.

  The Serengeti includes a cluster annotated sample specification file that you can use as an example, when you create your database cluster specification file. In the Serengeti Management Server, the specification sample file is located at opt/serengeti/samples/basic_cluster.json. You can change the configuration values in the cluster sample specification file to meet your needs. The only value, you cannot change is the value assigned to the role for each node group, which must always be basic.

  You can deploy a base with the data Extension plugin Big cluster by using a custom cluster specification file.

  To deploy the software on the basis of the VMS cluster, use the cluster list - command of detail, or runserengeti - ssh.sh cluster_name to get the IP address of the virtual machine. You can then use the IP address with applications such as Apache Ambari or Cloudera Manager to set up the virtual machine with the software of your choice. You can configure the management application using the serengeti of username and the password you specified when creating the cluster basis within large data Extensions when management tool requires a username and password for you to connect to the virtual machines.

• How to remove hosts in cluster without vCenter

  Hello
  a customer has a vSphere 5.0 U1 cluster with 2 host ESXi 5.0 U1.
  
  The vCenter VM is corrupt and there is no way to restore ( )no available backup ).
  Now I installed a new vCenter, how do I remove the old cluster hosts?
  

  
  

  Thank you
  Andrea

  Hello

  If vCenter is offline, I'll try to add hosts to the new vCenter. I'm sure it will connect.

• Cluster without a load balancer?

  Two interactive servers FMS can work this way:
  1. they both serve the same FLV VOD on both machines
  2. where a single server gets X users connected, next user (X + 1) is routed to the next server
  3. There is no hardware for load balancing
  
  Is this possible and if this is the case, how?

  Yes, that's possible, but there is nothing integrated FMS to cope. You must write your own application to do.

  I like to handle this by building a little app that queries the service of administration of each involved server once per second or more, and retrieves his stats on the instances of the application I need to keep track of (we'll call it the 'load swing app". In this application, I include functions to loop through the statistical data for each server and determine which makes the most sense to send the following to customer.

  Client side, I connect first to the load balancer app, providing an application ID that I want to connect to as an argument in the call to the connect() function. Load Balancing takes the best decision of server and returns the host name of the target server. Then, the client disconnects from the load balancer and connects to the target host.

• Microsoft Cluster in vSphere using RDM disks

  Gentlemen, I have doubts that sounds simple, but it is better to ask than to the hurt things.

  Here, in the company where I started work two weeks ago. We have two servers of files Windows Server 2012, both are part of Microsoft Cluster Services, these two servers are virtualized on VMware ESXi 5.5, each on a host, here we use vCenter HA and DRS.

  Well, these file servers 03 RDM disks connected to the fibre channel, storage only disks are online only on node 1, node 2 drives are present in the computer Manager, but marked offline.

  To my knowledge, my experience of simple Microsoft cluster, the disks must be online on all nodes for disaster recovery is quick, for example through cluster in Windows Server 2008 R2 and Hyper-V Server R2 of 2012 using iSCSI storage and always leave the disks online on all nodes.

  My question is: is there a reason why a node drives remain online and the other node is taken offline? Because of RDM technology?

  I can then do disks on node 2 as well as online without risk?

  I'm an environment that left another analyst configured, had never made Windows Server 2012 in virtualized VMware vSphere servers cluster using RDM disks, so made the questions, so instead of simply in clicking on node 2 of disks and makes them online it is better to ask before

  Thank you!

  Ivanildo, is the normal Windows Server Failover Clustering behavior, since it is an active/passive cluster architecture, where a single node read/write a disk at a time, and is not a problem due to the use of RDMS in vSphere environment.

  The bellow image show two discs a WSFC, where 6 disk Offline on that particular node and the 7 disc is online:

  

  And, do TRY not to put the disks as offline being online on another node through disk management, this task must be performed by using the Failover Cluster Management console.

• Mid 2012 Macbook Pro with or without retinal incredibly slow

  Hello, I'm typing this for my mother. It has a mid-2012 Macbook pro without the retina which is very slow. She has recently updated to 16 GB of ram, and we are all pretty sure she did her properly. He constantly beach balls and takes more than a minute to launch Safari. The fan is also strong enough now. He runs the El captain. Thank you in advance!

  Here's the EtreCheck:

  EtreCheck version: 3.0.3 (307)

  Report generated 2016-09-18 10:33:08

  Download EtreCheck from https://etrecheck.com

  Time 02:44

  Performance: Excellent

  Click the [Support] links to help with non-Apple products.

  Click [details] for more information on this line.

  Problem: Computer is too slow

  Description:

  The computer is very slow and beach ball

  Hardware Information: ⓘ

  MacBook Pro (13-inch, mid-2012)

  [Data sheet] - [User Guide] - [warranty & Service]

  MacBook Pro - model: MacBookPro9, 2

  1 2.5 GHz Intel Core i5 CPU: 2 strands

  16 GB expandable RAM - [Instructions]

  BANK 0/DIMM0

  OK 8 GB DDR3 1600 MHz

  BANK 1/DIMM0

  OK 8 GB DDR3 1600 MHz

  Bluetooth: Good - transfer/Airdrop2 taken in charge

  Wireless: en1: 802.11 a/b/g/n

  Battery: Health = Normal - Cycle count = 129

  Video information: ⓘ

  Graphics Intel HD 4000

  Color LCD 1280 x 800

  Software: ⓘ

  OS X El Capitan 10.11.6 (15-1004) - since startup time: less than an hour

  Disc information: ⓘ

  HTS545050A7E362 disk HARD APPLE disk0: (500,11 GB) (rotation)

  EFI (disk0s1) < not mounted >: 210 MB

  Recovery HD (disk0s3) < not mounted > [recovery]: 650 MB

  Macintosh HD (disk 1) /: 498,88 (Go 400,52 free)

  Encrypted AES - XTS unlocked

  Storage of carrots: disk0s2 499.25 GB Online

  HL-DT-ST DVD - RW GS41N)

  USB information: ⓘ

  Apple Inc. FaceTime HD camera (built-in)

  Apple Inc. Apple keyboard / Trackpad

  Computer, Inc. Apple IR receiver.

  Apple Inc. BRCM20702 hub.

  Apple Inc. Bluetooth USB host controller.

  Logitech USB receiver

  Lightning information: ⓘ

  Apple Inc. Thunderbolt_bus.

  Guardian: ⓘ

  Mac App Store and identified developers

  Kernel extensions: ⓘ

  / Applications/Parallels Access.app

  [loading] com.parallels.virtualhid (1.0.3 - SDK 10.9-2016-07-19) [Support]

  [loading] com.parallels.virtualsound (1.0.36 - 10.6 SDK - 2016-07-19) [Support]

  / Applications/Parallels Desktop.app

  com.parallels.kext.hypervisor [no charge] (11.2.0). 32581 - SDK 10.9 - 2016-07-10) [Support]

  com.parallels.kext.NetBridge [no charge] (11.2.0). 32581 - SDK 10.9 - 2016-07-10) [Support]

  com.parallels.kext.usbconnect [no charge] (11.2.0). 32581 - SDK 10.9 - 2016-07-10) [Support]

  com.parallels.kext.vnic [no charge] (11.2.0). 32581 - SDK 10.9 - 2016-07-10) [Support]

  Launch system officers: ⓘ

  [cannot] com.apple.gamed.plist (2015-08-23)

  [no charge] 7 tasks Apple

  [loading] 154 jobs Apple

  [running] Apple 76 jobs

  Launch system demons: ⓘ

  [no charge] 44 Apple jobs

  tasks of Apple 162 [loading]

  Apple 85 [performance] tasks

  Launch officers: ⓘ

  [loaded] com.adobe.AAM.Updater - 1.0.plist (2013-08-04) [Support]

  com.parallels.mobile.prl_deskctl_agent.launchagent.plist [running] (2016-07-19) [Support]

  [cannot] com.realvnc.vncserver.peruser.plist (2013-10-03) [Support]

  [loaded] com.realvnc.vncserver.prelogin.plist (2013-10-03) [Support]

  [loaded] com.teamviewer.teamviewer.plist (2015-03-02) [Support]

  [loaded] com.teamviewer.teamviewer_desktop.plist (2015-03-02) [Support]

  com.Trusteer.rapport.rapportd.plist [running] (2016-07-18) [Support]

  Launch demons: ⓘ

  [loading] com.adobe.SwitchBoard.plist (2013-05-15) [Support]

  [loading] com.adobe.fpsaud.plist (2016-06-13) [Support]

  [loading] com.microsoft.office.licensing.helper.plist (2010-08-25) [Support]

  com.parallels.mobile.Dispatcher.launchdaemon.plist [running] (2016-07-19) [Support]

  [loading] com.parallels.mobile.kextloader.launchdaemon.plist (2016-07-19)

  [loading] com.realvnc.vncserver.plist (2013-10-03) [Support]

  [loading] com.teamviewer.Helper.plist (2015-03-02) [Support]

  [loaded] com.teamviewer.teamviewer_service.plist (2015-03-02) [Support]

  com.Trusteer.rooks.rooksd.plist [running] (2016-07-18) [Support]

  User launch officers: ⓘ

  [loading] com. SoftwareSecure.goloader.plist (2015-11-23) [Support]

  [loading] com.adobe.AAM.Updater - 1.0.plist (2013-05-16) [Support]

  [loading] com.google.keystone.agent.plist (2016-07-12) [Support]

  com.parallels.mobile.startgui.launchagent.plist [running] (2016-09-18) [Support]

  Items in user login: ⓘ

  iTunesHelper Application (/ Applications/iTunes.app/Contents/MacOS/iTunesHelper.app)

  TomTomHOMERunner hidden Application (~/Library/Application Support/TomTom HOME/TomTomHOMERunner.app)

  Hidden Google Chrome application (/ Applications/Google Chrome.app)

  Plug-ins Internet: ⓘ

  SharePointBrowserPlugin: 14.0.0 (2012-12-31) [Support]

  FlashPlayer - 10.6: 22.0.0.192 - SDK 10.9 (2016-06-19) [Support]

  QuickTime Plugin: 7.7.3 (2016-08-03)

  AdobeExManDetect: AdobeExManDetect 1.1.0.0 - SDK 10.7 (2013-08-04) [Support]

  Flash Player: 22.0.0.192 - SDK 10.9 (2016-06-19) obsolete! Update

  Default browser: 601 - SDK 10.11 (2016-08-03)

  Safari extensions: ⓘ

  Open in Internet Explorer - Parallels - http://www.Parallels.com/fr/ (2014-06-07)

  3rd party preference panes: ⓘ

  Flash Player (2016-06-13) [Support]

  Trusteer Endpoint Protection (2016-08-04) [Support]

  Time Machine: ⓘ

  Time Machine not configured!

  Top of page process CPU: ⓘ

  6% WindowServer

  5% mdworker (22)

  3% kernel_task

  1% fontd

  0% cloudpaird

  Top of page process of memory: ⓘ

  997 MB kernel_task

  508 MB com.apple.WebKit.WebContent (2)

  Mdworker (22) 393 MB

  180 MB Safari

  Mds_stores 147 MB

  Virtual memory information: ⓘ

  11.00 GB of free RAM

  used 5.01 GB RAM (2.48 GB being cached)

  Used Swap 0 B

  Diagnostic information: ⓘ

  September 18, 2016, 09:50:31 ~/Library/Logs/DiagnosticReports/gamed_2016-09-18-095031_[redacted].crash

  /System/Library/PrivateFrameworks/GameCenterFoundation.Framework/versions/A/GAM ed

  18 September 2016, 09:42:52 self-test - spent

  Sep 17, 2016, 10:51:06 PM/Library/Logs/DiagnosticReports/QuickTime Player_2016-09-17-225106_ [redacted] .hang

  / Applications/QuickTime Player Player.app/Contents/MacOS/QuickTime

  Sep 17, 2016, ash /Library/Logs/DiagnosticReports/softwareupdated_2016-09-17-143914_[redacted].cr 14:39:14

  / System/Library/CoreServices/Software Update.app/Contents/Resources/softwareupdated

  Sep 17, 2016, 09:02:02 ~/Library/Logs/DiagnosticReports/Mail_2016-09-17-090202_[redacted].crash

  com Apple.Mail - /Applications/Mail.app/Contents/MacOS/Mail

  Sep 17, 2016, ~/Library/Logs/DiagnosticReports/Mail_2016-09-17-090028_[redacted].crash 09:00:28

  Sep 17, 2016, 08:44:32 AM/Library/Logs/DiagnosticReports/Google Chrome_2016-09-17-084432_ [redacted] .hang

  / Applications/Google Chrome Chrome.app/Contents/MacOS/Google

  Sep 17, 2016, 08:41:41 AM/Library/Logs/DiagnosticReports/softwareupdate_download_service_2016-09-17-0841 41_ [redacted] .crash

  / System/Library/CoreServices/Software Update.app/Contents/Resources/softwareupdate_download_service

  15 sep, 2016, 10:50:56 AM/Library/Logs/DiagnosticReports/softwareupdate_download_service_2016-09-15-1050 56_ [redacted] .crash

  Sep 15, 2016, 10:46:46 /Library/Logs/DiagnosticReports/apsd_2016-09-15-104646_[redacted].crash

  /System/Library/PrivateFrameworks/ApplePushService.framework/APSD

  DeannaMarie,

  Uninstall the report following the instructions of suppliers: http://www.trusteer.com/support/uninstalling-rapport-mac-os-x

  

• Create a cluster through the serengeti without a Hadoop distribution installed?

  Hello

  Is it possible to have the Serengeti create a cluster without Hadoop? I know it sounds like a silly question but I'm wanting to know if I can use of the Serengeti and basically create a set of virtual machines and IPs with defined storage and RAM. Then, I want to install my own packages, not Hadoop but Serengeti can create the initial virtual machines is so good.

  Thanks in advance,

  Carl.

  It worked, thanks. So I guess it was sudo sed-i "/ 'hadoop_namenode' / a 'basic', '/ opt/serengeti/www/distros/manifest"

  FINISHED 100%

  Node group: worker, the instance number: 1

  roles: [Basic]

  STATUS NAME IP TASK

  --------------------------------------------------

  worker-Basic-0 10.100.12.128 Service ready

  Node group: master, instance number: 1

  roles: [Basic]

  STATUS NAME IP TASK

  --------------------------------------------------

  Master-Basic-0 10.100.12.129 Service ready

  basic cluster created

  Serengeti >

  So thank you. He placed two VMS in pools of different resources. What config file defines what I do not see that it referenced in .json models in/opt/serengeti/conf.

• Changing the settings of Cluster SWAP without the virtual machine downtime

  Hi all

  My question refers to the vSphere 5.0 version.

  I need to change the settings of my VMware Cluster swap file.

  It is set to "store the swap file in the data specified by the host store.

  I want to change it to "store the file in the same directory as the virtual machine.

  Can I do this without the VM downtime?

  Kind regards

  Martin

  You can change the setting in the cluster without affecting your running virtual machines, but virtual machines will not use this new setting until they have been rolled power.