2012R2 server unable to RDP when it is specified to specific computers

Similar Questions

• 2012r2 Server PowerEdge 320 - can't find the drive

  I try to install windows Server 2012r2 to a PowerEdge 320.  The computer has a card mini-310 of PERC with two drives configured in a RAID1 array.  When I get to the disk selection window in the Windows installation, he sees disk 0 Partition 3 as "unused" and size = GB 1840,9.

  When I try select this option to have the target, the Setup program indicates that "we could not create a new partition or find an existing one."  For more information see the installation log files. »

  I tried formatting the partition, which works without error.  Windows still not install to it.

  I looked for a driver to download and nothing found for Windows 2012r2.  There is a driver for 2008r2.

  I have several R220 PowerEdge systems with the same PERC controller.  2012r2 Server installs to them without any problem at all.

  What Miss me?  How can I get Windows Installer on this server?

  Thanks - Bill Gee

  Hi Bill,

  Here is the driver for 2012 R2 http://www.dell.com/support/home/us/en/04/Drivers/DriversDetails?driverId=5382X&fileId=3460828789&osCode=W12R2&productCode=poweredge-r320&languageCode=EN&categoryId=SF Server

  What other partitions are listed? You can also try the following steps to activate the partition

  Once the installation program is unable to find the partition, close the settings window (the upper-right-side red X does the job).

  From this point, you should be brought back to the initial Setup screen. Choose 'Repair' then go to the advanced tools and start the command line.

  Run DISKPART.

  Type LIST DISK and identify your number (from 0 to n disks) SSD drive.

  Type SELECT DISK where is your SSD drive number.

  Type OWN

  Type CREATE PARTITION PRIMARY

  Type ACTIVE

  Type FORMAT FS = NTFS QUICK

  Type ASSIGN

  Type of OUTPUT twice (one for out of DiskPart, the other to exit the command line tool)

• Œuvres SQL query to MS SQL Server 2008, but not when you use the database kit

  I have this SQL query:

  DECLARE TABLE (@DataTypeTable)
  Name varchar (128).
  TypeID INT)

  -Add comma delimeted type data in the temporary table names
  INSERT INTO @DataTypeTable (name)
  SELECT * from WhatWeShouldDoRead.func_Split (@DataTypeTrimmed, ',')

  SELECT the name OF @DataTypeTable

  That takes a comma delimited by the string and returns the string as a table.  It works correctly in Microsoft SQL Server Management Studio.  When I run this as a stored procedure I return nothing.  There are no errors, SQL or otherwise.  I checked that I am connected to the correct database and the stored procedure is responsible without changing any error chain which is reported of this stored procedure (that code is not shown in the example above).  Has anyone seen this problem before, or have experience with SQL/Labview interfaces to tell me what I am doing wrong?

  Thanks in advance.

  
  

• Why remove the Terminal Server on Windows Server 2008 Standard Server HKEY_USERS\S -? When one connects users off?

  Why remove the Terminal Server on Windows Server 2008 Standard Server HKEY_USERS\S -? When one connects users off?

  I have a setting wrong?
  I can't find a setting that relates to this in either Terminal Server Config or Terminal Server Manager...
  Any help would be much appreciated.

  Hi Richard,

  Thanks for posting your question on Microsoft Community!

  I suggest you to ask your question in the section service Terminal Server TechNet forums for assistance.

  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

  I hope this helps.

• Error code: 800ccc0d, the server is not found, when I try to connect to servers using Windows Live Mail 2011 news

  Original title: 800ccc0d ERROR FIX

  Hi people, I am getting an error ("the server is not found") when trying to connect to my news server. Œuvres mail (hotmail) ok, but I can't connect to one of my two news servers I use (teranews and broadstripe). I've included the error code I have in the title above. I use Windows Live Mail 2011.

  Anyone has any ideas for patches?

  Hi kb3jlc,

  If this problem occurs only with Windows Live mail, you can post the question in the Windows Live community:

  http://windowslivehelp.com/product.aspx?ProductID=15

  Hope this information is useful.

• C# examples fail with "Failed to recognize the type of server or the version when connecting to the host"

  I am currently submitting work for P2V conversion from a c# application. I tried to run the application remotely and on-site, but I get this error message (here is the full error):

  "< detail > < InvalidArgumentFault xmlns =" urn: Converter ' xsi: type = "vim25:InvalidArgument" xmlns:vim25 = "urn: vim25" xmlns: xsi = "http://www.w3.org/2001/XMLSchema-instance" > < vim25:faultCause > < vim25:fault xsi: type = "ConverterNotSupportedConnection" > < hostName > RSMITH < / hostName > < / vim25:fault > < vim25:localizedMessage > impossible to recognize the type of server or the version when connecting to the host "RSMITH". " < / vim25: localizedMessage > < / vim25:faultCause > < / InvalidArgumentFault > < / details >

  RSMITH is the name of the machine with the VCenter Converter Standalone (5.0) and where I wan the VM to go. It's a Windows 7 SP1. I'm under .net 4.0 winform.

  Any suggestions? I'm pretty much run the sample out of the box, except for wrapping a winform around it instead of an application console.

  Cannot you telnet from your Converter machine on the source IDE oucederomsurlesecondport 9089 machine?

• How can I configure Messenger to record my conversations, record them and send them to a location I can read and save when you use Messenger on other computers than mine?

  How can I configure Messenger to record my conversations, record them and send them to a location I can read and save when you use Messenger on other computers than mine?

  original title: Live Messenger

  Hi Nicoliani,

  To start saving your Conversations in Windows Live Messenger

  1. connect to your window Live Messenger and click on 'Tools' or click on your display name.

  2. scroll down to "Options", a window should appear. When he does very well and click on "Messages".

  3. locate "historical Message". After that, check the box that says, "automatically keep a history of my conversations.

  4. below that you will see "save my conversations in this folder."

  5. to side of her you will see change, make sure that it is a file that you can access and watch later.

  6. If you are on a network, you can save it in a directory which you have access, or you can save it to a location and later mailed to yourself and access it later.

  Where chats are saved is given below.

  1. to access the Conversations go to the start bar and click My Documents. Then click on "my received files."

  2. There should be a folder with your name on it. Click the folder, then you will be in another folder called history. Continue

  3. by clicking on the folder, now you should see all your saved conversations.

  Hope this information is useful.

  Amrita M

  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• CP can send a pass mark for the LMS when the user reaches a specific slide?

  I use CP 6.1 and I was wondering if there is a way I can set my parameters of reports to send a pass mark for the LMS when the user reaches a specific slide?

  

  I don't want to 'pass' to be determined by a Quiz. I want to be determined by slide views or the number of slides. I want a "pass mark" to pass to the LMS only when the user reaches a SPECIFIC slide. Is this possible?

  Not with the views of the slide. It would not be acceptable to have an object on this slide, the user should click on? And then require a score equal to one set to this object (button, button shape, click box or even a text entry box)?

• Cannot use RDP when replace the esx esxi 5.5 4.1 Server

  Hello

  We have a new environment with vsphere 5.5 and device vcentre 5.5 5.5

  I've converted a few VM vsphere 4.1 to vsphere 5.5 there is between two servers that I can not open the RDP session to those servers somewhere else.

  No idea how that can happen? It works fine when I turn the machine on vsphere 5.5 and start again from the old environment vsphere 4.1.

  Thanks in advance...

  Sohrab

  Have you configured VLAN even that you have in your old Web host in your new? Any other server on the same VLAN / subnet works at your 5.5 ESXi host?

• User logged on the server over the RDP session - Small Business Server 2011 x 64

  We have a Small Business Server 2011 standard x 64.  We have the configuration of the remote desktop on port forwarding in the firewall to allow a user to connect to this server using RDP remote desktop.  This isn't a server terminal server.  No, there are no available Remote Desktop Manager settings.

  When the user connects through the RDP application and connects to the server.  If the users session is idle for 15 minutes, the user is connected to the server (not disconnected the RDP session, just to connect to the server).  The user must log into the server every time that happens.  We tried adjusting the Remote Desktop Session Host settings and changed the Session time limits, but this isn't the parameter we are looking for.  We have looked extensively through the default domain group policy and see nothing active to this behavior.  We examined local group policies and studied the session time limits in the user and computer configuration > policies > models Admin > RDP >... session host and it is has anything configured here which could trigger this behavior.

  Yet once, it connects the disabled user, not closing the remote session.  We have also examined the user account for this user and looked for resume posting require logon settings (although with SBS, it is not even there to adjust the display settings).  I had partner Microsoft supports focus on this during one hour (he didn't use too much of my time to support) and they have been unable to resolve within an hour.

  Help, please!

  Thank you.

  This issue is beyond the scope of this site and must be placed on Technet or MSDN

  http://social.technet.Microsoft.com/forums/en-us/home

  http://social.msdn.Microsoft.com/forums/en-us/home

• Windows SBS 2008 - user is unable to RDP in even through that it's in the appropriate groups

  Hi guys,.

  Problem: A user has been accidentally deleted from a Windows SBS 2008 server running Active Directory and we have been unable to grant him the rights of RDP - the error message indicates that the account must be granted "logon through Terminal Services right.

  The installer: A single Windows SBS 2008 server running hyper-VM with a unique virtual machine on it which manages the TS licenses

  Tried to bugs/more information:

  Things that we tried to do to solve the problem (all done via Active Directory users and computers)

  • He added to the administrators and remote desktop users groups
  • He added to the users group to the remote desktop on the virtual machine (the account can now connect to the virtual machine at least)
  • Cloned an existing account on the primary server
  • Removed and added the account through the SBS console and added to the admin and RDP groups (on the dedicated server and virtual machine)

  None of them seems to have solved the problem. There are currently 2 free licenses of TS, so I don't think it's a licensing issue.

  It's almost as if there is a top group policy setting or similar which replaces the user groups is added to, but I don't know where to look for here.

  I've already made sure that the user do not have TS access turned off in the settings of the user's

  Any suggestions?

  Hello

  Your question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the Server on TechNet. Please post your question in the Technet forums. You can follow the link to your question:

  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

• BI server does not start when the deployment improved SPR

  Hello
  I'm new to OBIEE 11 g. In my project I have a RPD 10 existing g HT. I upgraded to version 11g.5. I restarted all services. When I deploy improved SPR, biserver is a descendant. But if I deploy SampleAppLite.rpd (oracle supplied), all services begin. only for my bi Server RPD is going down.
  
  I don't know where it might be the problem...
  Pls help.
  
  Thank you
  Smita

  Hello

  This is a change in behavior when we have 10g and 11g. In BI EE 10 g, there was no Oracle Client delivered with BI EE. Thus, BI EE will use your Oracle DB client host to connect to the database. Usually not a problem in this case. But in BI EE 11 g, the software itself contains a client of 11.2 DB. Thus, when you try to connect to the database using the repository or the BI server, it will try to find the tnsnames entry in the customer Oracle of BI EE 11 g instead of your database. There are 2 options to work around this problem

  1. copy your tnsnames.ora {Oracle_BI1} \network\admin directory & {oracle_common} \network\admin directory (only the first is necessary because it is the ORACLE_HOME)

  2. or instead of the source tnsnames.ora entry, use the full expanded tnsnames as shown below

  (DESCRIPTION = (ADDRESS = (PROTOCOL = TCP) (HOST = 172.16.66.173)(PORT = 1521)) (CONNECT_DATA = (SERVER = DEDICATED)(SERVICE_NAME = orcl)))

  Both of the above will work.

  For more information:

  Unable to connect to the database of the OBIEE 11g improved SPR

• Tried all your suggestions and always receive "Unable to connect" when using ANY search engine.

  Can't use any search engine of FF 40.0.3 on Macbook Pro model with 10.8.5 OS 9.2. Receive "Unable to connect" message when you try to use a search engine. Other than the search engine and Mozilla Web sites to connect properly. 40.0.3 on another Mac FireFox works fine without any problems.

  In addition, I can not access the FF "Get modules" page or the home page of Mozilla. Search engines will connect not their home page or the search bar. Problem just started. I had previously been upgrade and have resorted, FF 40.0.3 without problem when it was issued. Solutions of attempts included refresh FF, launch FF in safe mode, run with all plugins disabled, graphics hardware acceleration disabled. None of these fixed the issue.

  Had already tried your suggestions, without success, but has once again to be sure. Without success. However, I made a further exploration of my own and found out that IPv6 is set to "Link Local" only in my router. I have reset on 'Automatic', the router reset to update, and my problem was solved. So it was the IPv6 setting (unlikely) or the router reset (probably) that solved the problem, or it is your suggestions I tried and did not work, COMBINED with the router reset which solved the problem (quite possible).

  Thanks for the comments!

• Flag fox module by default, a server of the Ireland when I go to amazon, it should stay in the United States.

  I have the add-on for Mozilla, FlagFox it tells me where the server I'm on now. When I go to the Amazon site that is immediately a flag of the Ireland. Information Flagfox gives me on this server is as follows. www.Amazon.com 176.32.98.166 Ireland. I'm a bit skeptical to connect to my account because of this. Can you help me with this? This happens on 2 systems of Ubuntu and Linux Mint 1 System. I'm under Fire Fox 17. Thanks Clyde

  The add-on you have shows you the location of the server of the Web site - it also provides much more. You can disable or remove modules to see if it helps. You can also contact the developer of the addon to the [email protected]

• My default download folder is on my server at work, so when I'm at home the download window does not open and I can't change my settings to download.

  I tried to reset my default download folder, but it just goes back in the download folder on my server to work that I won't be able to connect to the next month. When I try to select a different download folder, does not have the button "Browse". I also tried to select the option to ask me where to save every time, but nothing appears when I try to record something.

  You can also double-click the preferences that I mentioned in connection: config and manually add a custom - path C:\ for example will be the root folder of your hard disk the new default download location.

  and in case the settings are not saved after restarting firefox please see How to fix the preferences that will not save