2xCisco 871, 2 tunnels, 2 PSI on second router

Similar Questions

• Use the second router to extend the network to Time Capsule

  I have a v7.6.7 running Time Capsule 1 TB and older airport. I'm hoping to add a second router in a new location, and I use an ethernet cable from the TC at the new router (TP Link Archer C5), updated to the latest version of the firmware. The IP address of the TC is 192.168.1.1.

  I have set up my router C5 as follows: allocation of IP 192.168.1.199, value DHCP = off, and I connect a cable between the TC ports and port WAN (not Internet) available on the C5. In the C5 wireless settings, I tried both using the TC SSID and pw and creating a new SSID and pw. In both cases, the network will work for a short time, but eventually the entire network, including the TC, stops working. I made no changes to the parameters of the TC on any trial.

  Is it possible to use a TC and a router not Apple on the same network? If so, what are the right settings for the TC and the secondary router? If not, is it better to have the not Apple as main router and add the TC to the network created by the non-Apple router?

  Is it possible to use a TC and a router not Apple on the same network? If so, what are the right settings for the TC and the secondary router?

  Yes. That would be the basis of a network of mobile type.

  The key for a roaming network parameters are:

  • The 'primary' router must be configured as a router. In other words, it must have active NAT and DHCP services.
  • All other routers used in a network of roaming must be reconfigured as a bridge.
  • All routers must broadcast a Wi - Fi network that uses the same network (SSID, aka) name, and the type of wireless security, and the password.
  • All routers must be interconnected by Ethernet. To provide Powerline adapters using an Ethernet connectivity should also work.

  If not, is it better to have the not Apple as main router and add the TC to the network created by the non-Apple router?

  Should not really which is the main in the roaming network.

  I think at this point, your current circuit line. To check that, I would suggest that you consider to bring back the router C5 in the same room as you have the TC. Then connect it directly to one of the LAN of the TC ports. Complete the entire upward to a mobile network and test it. If everything works, bring back the C5 in the desired location, and then try again.

  If it fails, then the circuit line will be tested to check that it provides a solid 'Ethernet' connection between the adapters.

• Connection with a switch EZXS55W or a second router WRT54G to my router network WTR300N home?

  I have a home office in my basement with my computer connected to a lan of my WRT300N router that is set up on the first floor and networking with three additional computers to the floor as well. I want to add 2 additional computers in my basement and wireless is not a good set upward because the signal strength is very low. I have great reception on the floor and even on the second floor where my children are connected from their rooms. My question is: I have an older WRT54G Router I use is more and want to know if I can connect it to my WRT300N using the lan line ran down in the basement which is connected to one of the Ethernet ports of the WRT300N? If so, how the connection and set up the second router? Also, I can use Ethernet cables to connect my three computers to the second router or what I need to use the wireless of the second router? I was looking at the switch EZXS55W at the Wal-Mart local and thought that was my answer, but after a search through all the answers of the basis of knowledge here, I'm confused on the approach to take and which one would be the best game for me. Here, any help would be great!

  With the EZX you extended your wired LAN. You can still use the WRT54G to add another point for other cable ports and wireless access. Just do these 4 steps as stated in my previous post.

  You can connect the WRT54G the WRT300N or the EZX. Basically, it's all the same. You don't have to turn off the switch before you connect a device.

  If you want to use the additional wireless WRT54G, you can try to set up a roaming wireless network. Implement the WRT with identical settings as on the WRT300N wireless, i.e. identical SSID and wireless security the same (preferably WPA2) personal with a good password. Do not turn off the SSID broadcast on either WRT. Only the allocation of channels should be different at a time to avoid any interference. Now the devices should be able to move from one access point to another without losing the network connection.

  However, if you perform this configuration test carefully. I don't know how it works if you have a N Router and a G. If this does not work, use different SSID on both. You can then choose which SSID to connect to on the client.

• Add WRT54G: second router / access point, unable to get to the outside network.

  Here is the prob:

  We just got cable internet the other day and the cable operator insisted on using their v1000 Belkin F5D7234-4 instead of my WRT54G V8. So I thought I'd use the WRT54G as a second router/AP (without wireless/LAN/WAN). I was eager to do this by running an ethernet in the WAN on the WRT54G port and plug it into the port of the client on the Belkin, place the wrt - 54 G at the other end of the House and have the WRT54G broadcasting the same SSID and require authentication even as the Belkin and use the Belkin to Linksys Wireless Bridge. In this way, it will extend my wireless network and all computers can access the internet and the other (wireline customers will keep at wire-speed, wireless is not authicate to two different networks.)

  I can't get the Linksys network based able to see all the other computers outside the WRT - 54 G, even for wireless clients. On the side of things Belkin network, I can't ping the router even if she pulls a DHCP in the Belkin address. All customers the Belkin side can meet and thin internet. I've fiddled with the WRT54-g for almost an entire weekend now with no result. The WRT54G can see the other router as a DNS as well as external DNS providers, but none of the client computers can. Basically, I'm wanting to extend the network of Belkin 4 as most cable customers and fill a few dead wireless, and make the visible computer on the same network of suggestions?

  Parameters of WRT - 54G:

  Automatic configuration - DHCP

  Same domain name like Belkin
  IP router set a tire to the DHCP server

  DHCPserver OFF

  Mode of operation: router

  Safe are disabled.

  Wireless SSID is the same as Belkin

  Wireless channel is the same as belkin.

  Method and auth. key is the same as belkin.

  Belkin:

  DHCP is on.

  15 IP addresses available.

  Wireless gateway is on with the WRT54G Wireless MAC address information.

  Ethernet cords are connected.

  I played with static routes for hours, tried the option routing dynamic, even tried DMZing of the WRT54G intellectual property in the belkin and still unable to connect to the internet. Tried the Belkin MAC address cloning. Nothing seems to work. When I plug the WRT - 54G directly in my digital/Modem/phone cable box, I get internet and everything. I'm at the point of throwing same DD - WRT on it.

  But beyond connection "wireless" I discovered really does not work if well (drops random wireless speeds seize up) with two different pieces of equipment running two different firmwares. So the thing connecting wireless set was out the window.

  I however knew what I had to do Linksys firmware:

  1.) DHCP clients forward.

  Customers of Belkin - network

  Linksys customers - network B

  The dhcp pool was not get transferred to the client computers. That is the 1-2 on network computer had XXX. XXX.100 - 102 for 3-4 computers on network B was YYY. YYY. YYY statically set by Windows. Even after changing to a static address on the network A dhcp scope I could still connect to the internet or to one of the computers on the network.

  The static routing table seemed not lead me anywhere either, and I've tried dozens of configurations.

  The way I got it Setup is with the customer enthernet of the Belkin ROUTER to THE Internet on the Linksys WRT54G port 1-4. Maybe I should have plugged the ethernet on the client side of 4 ports Linksys?

  Anyway DD - WRT redirect DCHP feature was what I need.

  Regarding the scenario wireless two routers have the same encryption method and key but different channels and ssid. Who, with DD - WRT for some reason when I jump on the wireless-B, Vista will be ID it as network A (B).

  I hope that it has not violated anything except the guarantee which was anyway. The reason for which I needed for my network up this way is because I do a lot of work using VM (of various operating systems), is simply easier to have two separate semi networks. (to different physical locations in the House)

• Adding a Second router to my LAN

  I have 4 devices on my network-

  1 surfboard cable modem

  2. router WRT160N wireless - 192.168.1.1

  3 Linksys 10 / 100 5 port switch wired

  4 WRT160Nv3 - 192.168.1.2

  My current setup is-

  1. first router modem. (WAN PORT)

  2 port LAN router for UPLINK port on switch

  The switch is located on the first floor, the router is down.  The router's wifi fails on the floor, so I bought another WRT160Nv3

  How can I add this to my installation?  I tried hanging the new router direct to a PC and configure it so that it is NOT a DHCP server and last slot the IP 192.168.1.1 to 192.168.1.2 and then sign a LAN switch port in a new router LAN port and the pc the new router cable.

  In the above configuration, NOTHING after the switch works.  I can't internet while the switch is wired to the router second on any computer of attatched to the switch.  Internet wifi won't get (from second router)

  Any help would be greatly appreciated.  I'm not trying to make a repeat using the same SSID, just try adding an access point on my current setup.

  Everything worked fine with 1 Router DHCP and then switch to the floor, but no wifi up there.

  I made myself, solved by removing the switch from the configuration.  I'm sure that I could add it back in after the 2nd router, but for some reason, it wouldn't work with her inbetween the two routers.

• How to connect a second router WRT54G

  I can't get a signal through my entire House so I bought a second router WRT54G, running that the Setup disk affects only the first router so how do the other work?

  To connect two routers together, go here.

• Setup VPN on WRV210 as second router

  I'm trying to set up a network containing two routers, a primary giving me access to internet ADSL (a 3CRWDR101A-75 3com) and a secondary router which has VPN (Cisco WRV210).

  The main router has the following parameters of LAN: 192.168.0.1 / 255.255.255.0 with active DHCP.

  WRV210 has the following parameters of LAN: 192.168.1.1 / 255.255.255.0 with active DHCP.

  The cable connection is LAN port of the first router to second router Internet port.

  In this way, I'm able to get the Internet on 2 laptops connected to WRV210

  I also have a Panasonic IP/PBX connected on the second language (WRV210)

  I need to configure VPN on WRV210 to be able to get SIP calls outside the local network (via internet).

  As I am a novice in networks, both routers are the DEFAULT setting.

  I learned a lot during the last 7 days can understand the concepts of network management, but was unable to put in place the appropriate configuration.

  For example if I change WRV210 router mode gateway mode, I won't be able to surf the internet despite the assistance that says "the mode in which this router will work. If this router is hosted your connection of networks to the Internet, select gateway. If another router exists on your network, select route. When the router is selected, dynamic routing is enabled'

  Also I am able to ping the LAN 192.168.0.x WRV210 first but not on the other side (from primary router WRV210).

  I am confused to use and combine different settings (NAT, routing, Ports,...)

  I really appreciate if someone could provide a step by step to configure the appropriate network and be able to reach my IP - PBX on the second language of anywhere.

  Thank you

  Hi, Ghassan, port forwarding must be configured on the WRV210 router. The 3com device is basically a non-facteurs. If you need assistance with the creation of port forwarding, please call the small business assistance Center.

  http://www.Cisco.com/en/us/support/tsd_cisco_small_business_support_center_contacts.html

  -Tom
  Please mark replied messages useful

• additional NIC connected to the second router interface does not have IP

  Hi I have an esxi5 running on the hp with two physical NICs micro server that is visible on esxi as vmnic0 and vmnic1. Initially, I was working with vmnic0 as a main network as the interface of management and also VM NIC that is connected to my internet. No problem here. Now, I plugged the second card which is represented as vmnic1 to another router in my house that has its own separate subnet by wire of physics. This second router has its own Dhcp and set up correctly as I connect my mobile phone and tablet that and gets its ip DHCP server. However vmnic1 receives not all IP address. Here is the configuration:

  Phys. netcard vmnic0 192.168.1.254 (obtained from internet router ip) no problems, related to the management network vSwitch0

  Phys. netcard vmnic1? any IP connected to separate vSwitch2, physical network is connected to the router with DHCP with the range 10.0.1.2 10.0.1.1 - 10.0.1.100

  To debug effort, I imported vmnic1 in the virtual machine running on that ESXi and static ip address assigned 10.0.1.101, whereas it falls in the same subnet as the second router and tried to ping router (10.0.1.1) however got "destination unreachable". Obviously ping can't the second router.

  So my question is why? Can anyone help on this?

  I put below the esxi Network Setup:

  Thank you!

  I just pointed it arbitrarily when I created vSwitch2, does not interfere the vSwitch0. 2nd router lacks any setting of vlan.  Should not do and leave the vlan by default? Thank you

• Site to site VPN tunnel - cannot ping the second interface of the firewall peer inside2

  I have two ASA 5505 firewall each with a basic license: FWa and FWb. currently there is a VPN tunnel between them work. I added a second (inside2) interface to the firewall, FWb, but I can't ping firewall FWa, so that I can ping the inside interface of FWa.

  I can ping the FWb inside interface 192.168.20.1 from the FWa inside 172.16.1.1 interface, but I can not ping to the 10.52.100.10 of the FWa FWb inside2 interface. I can not ping the gateway host FWa 10.52.100.1.

  I show the essential configuration of two firewalls as well as the debug icmp output on the two firewalls that I ping the internal interfaces and of FWa FWb inside2.
  =========================================================

  Here is a skeleton of the FWa configuration:

  name 172.16.1.0 network-inside
  name 192.168.20.0 HprCnc Thesys
  name 10.52.100.0 ring52-network
  name 10.53.100.0 ring53-network
  name S.S.S.S outside-interface

  interface Vlan1
  nameif inside
  security-level 100
  IP 172.16.1.1 255.255.255.0
  !
  interface Vlan2
  Description Connection to 777 VLAN to work around static Comast external Modem and IP address.
  nameif outside
  security-level 0
  outside interface IP address 255.255.255.240

  the DM_INLINE_NETWORK_5 object-group network
  network-object HprCnc Thesys 255.255.255.0
  ring52-network 255.255.255.0 network-object
  ring53-network 255.255.255.0 network-object

  the DM_INLINE_NETWORK_3 object-group network
  ring52-network 255.255.255.0 network-object
  network-object HprCnc Thesys 255.255.255.0
  ring53-network 255.255.255.0 network-object

  outside-interface of the access-list extended permitted Outside_5_cryptomap ip host object-group DM_INLINE_NETWORK_3
  inside_nat_outbound list extended access allowed inside-network ip, 255.255.255.0 DM_INLINE_NETWORK_5 object-group
  permit access list extended ip host 173.162.149.72 Outside_nat0_outbound aus_asx_uat 255.255.255.0

  NAT (inside) 0 access-list sheep
  NAT (inside) 101-list of access inside_nat_outbound
  NAT (inside) 101 0.0.0.0 0.0.0.0
  NAT (outside) 0-list of access Outside_nat0_outbound

  card crypto VPN 5 corresponds to the address Outside_5_cryptomap
  card crypto VPN 5 set pfs Group1
  VPN 5 set peer D.D.D.D crypto card
  VPN 5 value transform-set VPN crypto card
  tunnel-group D.D.D.D type ipsec-l2l
  IPSec-attributes tunnel-Group D.D.D.D
  pre-shared key *.

  =========================================================

  FWb:

  name 10.52.100.0 ring52-network
  name 10.53.100.0 ring53-network
  name 10.51.100.0 ring51-network
  name 10.54.100.0 ring54-network

  interface Vlan1
  nameif inside
  security-level 100
  address 192.168.20.1 255.255.255.0
  !
  interface Vlan2
  nameif outside
  security-level 0
  address IP D.D.D.D 255.255.255.240
  !
  interface Vlan52
  prior to interface Vlan1
  nameif inside2
  security-level 100
  IP 10.52.100.10 255.255.255.0

  the DM_INLINE_NETWORK_3 object-group network
  ring52-network 255.255.255.0 network-object
  ring53-network 255.255.255.0 network-object

  the DM_INLINE_NETWORK_2 object-group network
  ring52-network 255.255.255.0 network-object
  object-network 192.168.20.0 255.255.255.0
  ring53-network 255.255.255.0 network-object

  inside_nat0_outbound to access extended list ip 192.168.20.0 allow 255.255.255.0 host S.S.S.S
  inside2_nat0_outbound list extended access allowed object-group DM_INLINE_NETWORK_3 S.S.S.S ip host

  outside_1_cryptomap list extended access allowed object-group DM_INLINE_NETWORK_2 S.S.S.S ip host

  NAT (inside) 0-list of access inside_nat0_outbound
  NAT (inside) 1 0.0.0.0 0.0.0.0
  inside2_nat0_outbound (inside2) NAT 0 access list
  NAT (inside2) 1 0.0.0.0 0.0.0.0

  Route inside2 network ring51 255.255.255.0 10.52.100.1 1
  Route inside2 network ring53 255.255.255.0 10.52.100.1 1
  Route inside2 network ring54 255.255.255.0 10.52.100.1 1

  card crypto outside_map 1 match address outside_1_cryptomap
  card crypto outside_map 1 set pfs Group1
  outside_map game 1 card crypto peer S.S.S.S
  card crypto outside_map 1 set of transformation-ESP-3DES-SHA
  outside_map interface card crypto outside

  tunnel-group S.S.S.S type ipsec-l2l
  IPSec-attributes tunnel-group S.S.S.S
  pre-shared key *.

  =========================================================================
  I'm Tournai on icmp trace debugging on both firewalls and could see the traffic arriving at the inside2 interface, but never return to FWa.

  Ping Successul FWa inside the interface on FWb

  FWa # ping 192.168.20.1
  Type to abort escape sequence.
  Send 5, echoes ICMP 100 bytes to 192.168.20.1, time-out is 2 seconds:
  Echo request ICMP from outside-interface to 192.168.20.1 ID = 32068 seq = 23510 len = 72
  ! ICMP echo reply to 192.168.20.1 in outside-interface ID = 32068 seq = 23510 len = 72
  ....

  FWb #.
  Echo ICMP of S.S.S.S to 192.168.20.1 ID request = 32068 seq = 23510 len = 72
  ICMP echo reply 192.168.20.1 S.S.S.S ID = 32068 seq = 23510 len = 72
  ==============================================================================
  Successful ping of Fwa on a host connected to the inside interface on FWb

  FWa # ping 192.168.20.15
  Type to abort escape sequence.
  Send 5, echoes ICMP 100 bytes to 192.168.20.15, wait time is 2 seconds:
  Echo request ICMP from outside-interface to 192.168.20.15 ID = seq 50862 = 18608 len = 72
  ! ICMP echo reply to 192.168.20.15 in outside-interface ID = seq 50862 = 18608 len = 72
  ...

  FWb #.
  Inside outside:S.S.S.S ICMP echo request: 192.168.20.15 ID = seq 50862 = 18608 len = 72
  ICMP echo reply to Interior: 192.168.20.15 outside:S.S.S.S ID = seq 50862 = 18608 len = 72

  ===========================
  Unsuccessful ping of FWa to inside2 on FWb interface

  FWa # ping 10.52.100.10
  Send 5, echoes ICMP 100 bytes to 10.52.100.10, wait time is 2 seconds:
  Echo request ICMP from outside-interface to 10.52.100.10 ID = 19752 seq = 63173 len = 72
  ? Echo request ICMP from outside-interface to 10.52.100.10 ID = 19752 seq = 63173 len = 72
  ...

  FWb #.
  10.52.100.10 ID of S.S.S.S ICMP echo request = 19752 seq = 63173 len = 72
  10.52.100.10 ID of S.S.S.S ICMP echo request = 19752 seq = 63173 len = 72
  ....

  ==================================================================================

  Unsuccessful ping of Fwa to a host of related UI inside2 on FWb

  FWa # ping 10.52.100.1
  Type to abort escape sequence.
  Send 5, echoes ICMP 100 bytes to 10.52.100.1, wait time is 2 seconds:
  Echo request ICMP from outside-interface to 10.52.100.1 ID = 11842 seq = 15799 len = 72

  FWb #.
  Echo request ICMP outside:S.S.S.S to inside2:10.52.100.1 ID = 11842 seq = 15799 len = 72
  Echo request ICMP outside:S.S.S.S to inside2:10.52.100.1 ID = 11842 seq = 15799 len = 72

  =======================

  Thank you

  Hi odelaporte2,

  Is very probably the "access management" command is not applied in the second inside, only inside primary (see the race management) which will confirm.

  This command can be applied to an interface at a time, for example, if the law is now applied to the inside, it can not be applied to the inside2 at the same time.

  It may be useful

  -Randy-

• IPSec tunnel and join a LAN router

  I have to tunnel MikroTik IPSec Cisco ASA.

  Cisco WAN: xxx.xxx.xxx.xxx

  Cisco LAN: 172.27.0.0/20

  MikroTik WAN: .yyy

  MikroTik LAN: 172.27.128.0/20

  This acts to Cisco configuration:

  access extensive list ip 172.27.0.0 acl_encrypt allow 255.255.240.0 172.27.128.0 255.255.240.0

  access extensive list ip 172.27.0.0 acl_no_nat_inside allow 255.255.240.0 172.27.128.0 255.255.240.0

  NAT-control
  Global 1 interface (outside)
  NAT (inside) 0-list of access acl_no_nat_inside
  NAT (inside) 1 0.0.0.0 0.0.0.0

  Crypto ipsec transform-set esp-aes-256 ts_esp_aes_256_sha, esp-sha-hmac

  card crypto cm_outside 10 correspondence address acl_encrypt
  card crypto cm_outside pfs set 10 group5
  card crypto cm_outside 10 peers set.yyy
  card crypto cm_outside 10 transform-set ts_esp_aes_256_sha
  3600 seconds, duration of life card crypto cm_outside 10 set - the security association
  card crypto cm_outside 10 set security-association life 1048576 kilobytes

  cm_outside interface card crypto outside

  crypto ISAKMP policy 10
  preshared authentication
  aes-256 encryption
  sha hash
  Group 5
  life 3600

  tunnel - group.yyy type ipsec-l2l
  tunnel - group.yyy ipsec-attributes
  pre-shared-key *.

  Tunnel works fine, when I try to ping from a PC behind Cisco to another PC behind MikroTik.

  (e.g. 172.27.1.1 to 172.27.129.1), it works fine (except the first two lost packages which is OK
  due to the delay of its ISAKMP/IPsec negotiation).

  But I need to be able to access a PC behind Cisco's MikroTik.

  If I try for example

  ping 172.27.129.1

  Cisco, all packets are lost.

  I guess that Cisco does not use its LAN interface but the WAN interface.

  What can I do to make it work?

  Not sure why you want to do.

  Yes, ASA use the IP address on the outgoing interface as source IP address. So when you ping the remote of the SAA, it will WAN IP.

  You can add the following entry in your ACL to see if it works

  access-list allowed acl_encrypt ip xxx.xxx.xxx.xxx host 172.27.129.1

  Make the changes to the ACL on the remote site as well.

  You may or may not add a NAT 0 as well. I don't know because this traffic is started from ASA itself. You can check the log to see what's happening and then make the decision.

• Tunnel of RV042 V3 that routes all traffic to the VPN

  Hi all

  I use Cisco Linksys RV-042 with V2 hardware to set up a VPN tunnel that route all traffic to the remote gateway (a Cisco ASA 5510). This configuration works very well, and I can access the local router and other resources to the central site.

  I'm doing the same thing with Cisco RV042 with version V3 of the material, but I can't access the local router until the VPN breaks down. I can ' ping, SNMP the local router, or access but I can access the central site. Very strange.

  Do you know what can I do to access the router local (for example, hardware V2) with connected VPN?

  Thank you

  Rafael

  Just a hunch, but in the remote network you agree with what the network and subnet?

  I've seen this symptom before.

  LAN on the RV series.

  10.10.2.0 255.255.255.0

  Trust remote networks

  10.10.1.0 255.255.248.0

  It is traffic destined to the router on the 10.10.2.1 ip address is through the tunnel forward. So, for this purpose, you can only access the router LAN interface when the tunnel is out of service. I'm not sure why ping works but it does. I'm looking into this symptom on a different device, but the device has a similar graphical interface.

  I would like to know if you have a similar setup.

  Cisco Small Business Support Center

  Randy Manthey

  CCNA, CCNA - security

• ASA 8.4 (3) - applying NAT breaks my tunnel from site to site - "Routing failed.

  So I'm a few 5510 preconfiguration is before shipment to the site. I have my tunnel VPN from Site to Site and can ping of internal subnets between the sites. However, as soon as I configure NAT on my interface my pings die outside. I checked a guide very full config posted by TAC and I think the answer is to set up two times-NAT, which I believe I did. I don't always get no package in the tunnel.

  A hint, I found, is that I get the journaled message when NAT is applied & affecting routing "ASA-6-110003: routing could not locate the next hop for ICMP from Outside:10.56.8.4/512 to Internal:172.16.60.253/0.

  Output sh run object / run object-group sh / sh run nat / show the two ASA nat: -.

  SITE 1

  = sh run object
  network obj_any object
  subnet 0.0.0.0 0.0.0.0
  network of the BH-Asterisk object
  host x.x.x.x
  BG Hill Asterisk description
  network of the BH-Exchange object
  host x.x.x.x
  BG Hill Exchange Server description
  the DH - AV object network
  10.56.20.0 subnet 255.255.255.0
  Description AV DH
  the DH-Asterisk object network
  host x.x.x.x
  DH Asterisk description
  the object-Diffie-Hellman exchange network
  Home 10.56.1.253
  Description Exchange Diffie-Hellman
  the DH-guests object network
  10.56.8.0 subnet 255.255.255.0
  DH customers description
  the object DH ME network
  10.56.24.0 subnet 255.255.255.0
  DH ME description
  the DH-phones object network
  10.56.16.0 subnet 255.255.255.0
  Description phones DH
  network of the DH-security object
  10.56.32.0 subnet 255.255.255.0
  Description safety DH
  DH-internal object network
  10.56.1.0 subnet 255.255.255.0
  Description internal DH
  network object internally-BH
  10.60.1.0 subnet 255.255.255.0
  Description internal BH
  network of the BH-phones object
  10.60.16.0 subnet 255.255.255.0
  Description BH phones
  network of the BH-security object
  10.60.32.0 subnet 255.255.255.0
  BH Security description
  network of the BH - AV object
  10.60.20.0 subnet 255.255.255.0
  Description AV BH
  network of the BH-guests object
  10.60.8.0 subnet 255.255.255.0
  BH invited description
  network of the BH - ASA object
  host 1.1.1.1
  the DH - ASA object network
  host 1.1.1.2
  network of the BH-RAS object
  10.60.99.0 subnet 255.255.255.0
  the DH-RAS object network
  10.56.99.0 subnet 255.255.255.0
  network of the NETWORK_OBJ_10.56.99.0_26 object
  255.255.255.192 subnet 10.56.99.0
  network of the BH-UC560 object
  Home 172.16.60.253
  network of the DH-UC560 object
  Home 172.16.56.253

  = RJ5510-DOHA # sh run object-group
  the BGHill object-group network
  Description of subnets in BGHill
  BH-internal network-object
  network-object BH-phones
  network-object BH - AV
  network-object BH-security
  network-object BH-guests
  network-object BH-RAS
  BH-UC560 network-object
  object-group network DH
  Description of subnets in DH
  network-object DH - AV
  network-object DH-guests
  network-object DH ME
  network-object DH-phones
  network-object DH-security
  DH-internal network-object
  network-object DH-RAS
  network object-DH-UC560

  = RJ5510-DH # sh run nat
  NAT (AV, outdoors) static source DH DH static destination BGHill BGHill
  NAT (comments, outdoors) static source DH DH static destination BGHill BGHill
  NAT (inside, outside) static source DH DH static destination BGHill BGHill
  NAT (phones, outdoors) static source DH DH static destination BGHill BGHill
  NAT (safety, outdoors) static source DH DH static destination BGHill BGHill
  NAT (ME out) static source DH DH static destination BGHill BGHill
  !
  the DH - AV object network
  dynamic NAT interface (AV, outdoors)
  the object-Diffie-Hellman exchange network
  x.x.x.x static NAT (indoor, outdoor)
  the DH-guests object network
  dynamic NAT interface (comments, outdoors)
  the object DH ME network
  dynamic NAT interface (ME, outdoor)
  the DH-phones object network
  dynamic NAT interface (phones, outdoors)
  network of the DH-security object
  dynamic NAT interface (safety, outdoors)
  DH-internal object network
  dynamic NAT interface (indoor, outdoor)

  = HD-RJ5510 # see nat
  Manual NAT policies (Section 1)
  1 (f) (outdoor) static source DH DH destination static BGHill BGHill
  translate_hits = 0, untranslate_hits = 386
  2 (guest) (outdoor) static source DH DH destination static BGHill BGHill
  translate_hits = 180, untranslate_hits = 0
  3 (inside) (outside) static source DH DH destination static BGHill BGHill
  translate_hits = 0, untranslate_hits = 0
  4 (phones) (outdoor) static source DH DH destination static BGHill BGHill
  translate_hits = 0, untranslate_hits = 0
  5 (security) (outdoor) static source DH DH destination static BGHill BGHill
  translate_hits = 0, untranslate_hits = 0
  6 (ME) (outdoor) static source DH DH destination static BGHill BGHill
  translate_hits = 0, untranslate_hits = 0

  Auto NAT policies (Section 2)
  1 (outdoor) source static-Exchange Diffie-Hellman x.x.x.x (internal)
  translate_hits = 0, untranslate_hits = 0
  2 (internal) interface of DH-internal dynamics of the source (outdoor)
  translate_hits = 0, untranslate_hits = 0
  3 (comments) interface (outside) dynamic source DH-guests
  translate_hits = 2, untranslate_hits = 0
  4 (phones) to the dynamic interface of DH-phones of the source (outside)
  translate_hits = 0, untranslate_hits = 0
  5 (AV) to dynamic source DH - AV interface (outside)
  translate_hits = 0, untranslate_hits = 0
  6 (I) dynamic source DH-ME interface (outside)
  translate_hits = 0, untranslate_hits = 0
  7 (security) to DH-security dynamic interface of the source (outside)
  translate_hits = 0, untranslate_hits = 0

  SITE 2: -.

  = object # executed sh
  network obj_any object
  subnet 0.0.0.0 0.0.0.0
  network of the BH-Asterisk object
  host x.x.x.x
  BH Hill Asterisk description
  network of the BH-Exchange object
  Home 10.60.1.253
  BH Hill Exchange Server description
  the DH - AV object network
  10.56.20.0 subnet 255.255.255.0
  Description AV DH
  the DH-Asterisk object network
  host x.x.x.x
  DH Asterisk description
  the object-Diffie-Hellman exchange network
  host x.x.x.x
  Description Exchange Diffie-Hellman
  the DH-guests object network
  10.56.8.0 subnet 255.255.255.0
  DH customers description
  the object DH ME network
  10.56.24.0 subnet 255.255.255.0
  DH ME description
  the DH-phones object network
  10.56.16.0 subnet 255.255.255.0
  Description phones DH
  network of the DH-security object
  10.56.32.0 subnet 255.255.255.0
  Description safety DH
  DH-internal object network
  10.56.1.0 subnet 255.255.255.0
  Description internal DH
  network object internally-BH
  10.60.1.0 subnet 255.255.255.0
  Description internal BH
  network of the BH-phones object
  10.60.16.0 subnet 255.255.255.0
  Description BH phones
  network of the BH-security object
  10.60.32.0 subnet 255.255.255.0
  BH Security description
  network of the BH - AV object
  10.60.20.0 subnet 255.255.255.0
  Description AV BH
  network of the BH-guests object
  10.60.8.0 subnet 255.255.255.0
  BH invited description
  network of the BH - ASA object
  host 1.1.1.1
  the DH - ASA object network
  host 1.1.1.2
  network of the NETWORK_OBJ_10.60.99.0_26 object
  255.255.255.192 subnet 10.60.99.0
  network of the BH-RAS object
  10.60.99.0 subnet 255.255.255.0
  the DH-RAS object network
  10.56.99.0 subnet 255.255.255.0
  network of the BH-UC560 object
  Home 172.16.60.253
  network of the DH-UC560 object
  Home 172.16.56.253

  = # sh run object-group
  the BHHill object-group network
  Description of subnets in BH Hill
  BH-internal network-object
  network-object BH-phones
  network-object BH - AV
  network-object BH-security
  network-object BH-guests
  network-object BH-RAS
  BH-UC560 network-object
  object-group network DH
  Description of subnets in DH
  network-object DH - AV
  network-object DH-guests
  network-object DH ME
  network-object DH-phones
  network-object DH-security
  DH-internal network-object
  network-object DH-RAS
  network object-DH-UC560

  = # sh run nat
  NAT (inside, outside) static source BHHill BHHill static destination DH DH
  NAT (AV, outdoors) static source BHHill BHHill static destination DH DH
  NAT (comments, outdoors) static source BHHill BHHill static destination DH DH
  NAT (phones, outdoors) static source BHHill BHHill static destination DH DH
  NAT (safety, outdoors) static source BHHill BHHill static destination DH DH
  !
  network of the BH-Exchange object
  x.x.x.x static NAT (indoor, outdoor)
  network object internally-BH
  dynamic NAT interface (indoor, outdoor)
  network of the BH-phones object
  dynamic NAT interface (phones, outdoors)
  network of the BH-security object
  dynamic NAT interface (safety, outdoors)
  network of the BH - AV object
  dynamic NAT interface (AV, outdoors)
  network of the BH-guests object
  dynamic NAT interface (comments, outdoors)

  = # sh nat
  Manual NAT policies (Section 1)
  1 (inside) (outside) static source BHHill BHHill static destination DH DH
  translate_hits = 421, untranslate_hits = 178
  2 (AV) to (outside) static source BHHill BHHill static destination DH DH
  translate_hits = 0, untranslate_hits = 0
  3 (guest) (outdoor) static source BHHill BHHill static destination DH DH
  translate_hits = 0, untranslate_hits = 0
  4 (phones) (outdoor) static source BHHill BHHill static destination DH DH
  translate_hits = 0, untranslate_hits = 0
  5 (security) (outdoor) static source BHHill BHHill static destination DH DH
  translate_hits = 0, untranslate_hits = 0

  Auto NAT policies (Section 2)
  1 (outdoor) static source BH-Exchange x.x.x.x (internal)
  translate_hits = 0, untranslate_hits = 0
  2 (internal) interface of BH-internal dynamics of the source (outdoor)
  translate_hits = 0, untranslate_hits = 0
  3 (comments) interface (outside) dynamic source BH-guests
  translate_hits = 0, untranslate_hits = 0
  4 (phones) to the dynamic interface of BH-phones of the source (outside)
  translate_hits = 0, untranslate_hits = 0
  5 (AV) to dynamic source BH - AV interface (outside)
  translate_hits = 0, untranslate_hits = 0
  6 (security) at the interface of BH-security dynamic of the source (outdoor)
  translate_hits = 0, untranslate_hits = 0
  RJ5510-BH #.

  I admit that I am scoobied with this one, but I hope that someone will find the capture?

  Thank you

  In fact, the problem is with the NAT because because you use the same object on different States of NAT attached to different interfaces.

  The SAA can go crazy with it...

  I must leave now.

  As soon as I get back I'll explain this a little further.

  Kind regards

  Julio

  Note all useful posts

• Please help put in place the second router Wireless extender

  Morning everyone,

  I bought a Linksys WRT 1900AC recently to replace my Linksys E2500. The wi - fi signal is much stronger, but he can barely do in my room. As such, I would use my old E2500 as a range extender. I have already run the ethernet cable (cat 6) from the router WRT 1900AC main to the E2500.

  After spending 2 days by reading the documents, I still have the problem to connect two routers. My understanding of routers and networks is limited.  I would appreciate your help.

  Here's what I want to accomplish:

  1 cable connection to the internet is through (E2500 PC); OR

  2. connecting to the Internet via wifi

  3. If possible, using the same SSID for both routers

  Please give me instructions step by step, if you can. My understanding on this subject is poor.  Thank you for your help.

  Noos.

  PS. If you have a easier and/or a better way to extend my range, I'd like to hear it.

  see if the instructions here helps. Follow configuring lan lan step by step and you should be able to do work. http: http://www.linksys.com/us/support-article?articleNum=132275/www.linksys.com/us/support-article...

• As a second router WRT54G

  Hello

  In my home network, I have two routers connected LAN - LAN mode. My main router (not a Linksys router) is connected to the ISP by modem and my secondary router, which is a Linksys wrt54g, connected to the main router with wired connection. I followed the instructions here:

  http://www.Linksys.com/ca/support-article?articleNum=132275

  Everything works fine except that I can't access the administration page of the secondary router remotely. I tried to configure the VPN connection and redirect to the main router, but the administration of the port of the secondary router page is not accessible (while the accessible primary router administration page).

  My question is can I access the administration page of the secondary router remotely when two routers connected? If yes how do I configure the router of the secondary (VPN, port forwarding, etc.) and the first?

  Thank you in advance.

  Hi, topplenz. Possible reasons that you cannot remotely access the secondary router is because the DHCP server has been disabled through the installation of LAN to LAN and the secondary router depends on the IP address of the a main. We suggest to use the LAN to WAN cascading instead.

  Jay-15354

  Linksys technical support

• Using my Linksys BEFSR81 as a second router for Xbox

  Hello.  I bought an Xbox and you need conntect the game unit and a computer to the main router in another room.  There are no ports available so I used my old Linksys BEFSR81 router.  In order to get connectivity, I placed the cable that normally went to the back of the computer in the room where the Xbox is in an open port on the back of the router and then connected the computer and the Xbox of extra cables in two other ports on the back of the router.  It works well; However, we lose connectivity every night during the night.  To restore, I have to unplug my Netgear router and unplug the cable that goes to the Linksys, make my Netgear upward and run it again and THEN plug the Netgear cable which connects the room with the computer and Xbox.

  I was I need to disable DHCP on the router Linksys configuration page, but cannot be cannot access.  It is only to the top of my main Netgear router.  Default IP gateway is the same on both routers, I think.  I can't change because I can't access the Linksys configuration.  I tried to release and rescued by run/cmd/ipconfig/releaset, etc., but it keeps telling me that there is an error at the point of renewal.  Any suggestions how to get into the router configuration page?  Thank you!

  Well, that was the answer - THANKS!  He actually told me that my computer, called by his name, was now manage this computer through the network.  Forget the text, but it worked!

  You are the best - thanks!