Setup VPN on WRV210 as second router

Similar Questions

• Add WRT54G: second router / access point, unable to get to the outside network.

  Here is the prob:

  We just got cable internet the other day and the cable operator insisted on using their v1000 Belkin F5D7234-4 instead of my WRT54G V8. So I thought I'd use the WRT54G as a second router/AP (without wireless/LAN/WAN). I was eager to do this by running an ethernet in the WAN on the WRT54G port and plug it into the port of the client on the Belkin, place the wrt - 54 G at the other end of the House and have the WRT54G broadcasting the same SSID and require authentication even as the Belkin and use the Belkin to Linksys Wireless Bridge. In this way, it will extend my wireless network and all computers can access the internet and the other (wireline customers will keep at wire-speed, wireless is not authicate to two different networks.)

  I can't get the Linksys network based able to see all the other computers outside the WRT - 54 G, even for wireless clients. On the side of things Belkin network, I can't ping the router even if she pulls a DHCP in the Belkin address. All customers the Belkin side can meet and thin internet. I've fiddled with the WRT54-g for almost an entire weekend now with no result. The WRT54G can see the other router as a DNS as well as external DNS providers, but none of the client computers can. Basically, I'm wanting to extend the network of Belkin 4 as most cable customers and fill a few dead wireless, and make the visible computer on the same network of suggestions?

  Parameters of WRT - 54G:

  Automatic configuration - DHCP

  Same domain name like Belkin
  IP router set a tire to the DHCP server

  DHCPserver OFF

  Mode of operation: router

  Safe are disabled.

  Wireless SSID is the same as Belkin

  Wireless channel is the same as belkin.

  Method and auth. key is the same as belkin.

  Belkin:

  DHCP is on.

  15 IP addresses available.

  Wireless gateway is on with the WRT54G Wireless MAC address information.

  Ethernet cords are connected.

  I played with static routes for hours, tried the option routing dynamic, even tried DMZing of the WRT54G intellectual property in the belkin and still unable to connect to the internet. Tried the Belkin MAC address cloning. Nothing seems to work. When I plug the WRT - 54G directly in my digital/Modem/phone cable box, I get internet and everything. I'm at the point of throwing same DD - WRT on it.

  But beyond connection "wireless" I discovered really does not work if well (drops random wireless speeds seize up) with two different pieces of equipment running two different firmwares. So the thing connecting wireless set was out the window.

  I however knew what I had to do Linksys firmware:

  1.) DHCP clients forward.

  Customers of Belkin - network

  Linksys customers - network B

  The dhcp pool was not get transferred to the client computers. That is the 1-2 on network computer had XXX. XXX.100 - 102 for 3-4 computers on network B was YYY. YYY. YYY statically set by Windows. Even after changing to a static address on the network A dhcp scope I could still connect to the internet or to one of the computers on the network.

  The static routing table seemed not lead me anywhere either, and I've tried dozens of configurations.

  The way I got it Setup is with the customer enthernet of the Belkin ROUTER to THE Internet on the Linksys WRT54G port 1-4. Maybe I should have plugged the ethernet on the client side of 4 ports Linksys?

  Anyway DD - WRT redirect DCHP feature was what I need.

  Regarding the scenario wireless two routers have the same encryption method and key but different channels and ssid. Who, with DD - WRT for some reason when I jump on the wireless-B, Vista will be ID it as network A (B).

  I hope that it has not violated anything except the guarantee which was anyway. The reason for which I needed for my network up this way is because I do a lot of work using VM (of various operating systems), is simply easier to have two separate semi networks. (to different physical locations in the House)

• Adding a Second router to my LAN

  I have 4 devices on my network-

  1 surfboard cable modem

  2. router WRT160N wireless - 192.168.1.1

  3 Linksys 10 / 100 5 port switch wired

  4 WRT160Nv3 - 192.168.1.2

  My current setup is-

  1. first router modem. (WAN PORT)

  2 port LAN router for UPLINK port on switch

  The switch is located on the first floor, the router is down.  The router's wifi fails on the floor, so I bought another WRT160Nv3

  How can I add this to my installation?  I tried hanging the new router direct to a PC and configure it so that it is NOT a DHCP server and last slot the IP 192.168.1.1 to 192.168.1.2 and then sign a LAN switch port in a new router LAN port and the pc the new router cable.

  In the above configuration, NOTHING after the switch works.  I can't internet while the switch is wired to the router second on any computer of attatched to the switch.  Internet wifi won't get (from second router)

  Any help would be greatly appreciated.  I'm not trying to make a repeat using the same SSID, just try adding an access point on my current setup.

  Everything worked fine with 1 Router DHCP and then switch to the floor, but no wifi up there.

  I made myself, solved by removing the switch from the configuration.  I'm sure that I could add it back in after the 2nd router, but for some reason, it wouldn't work with her inbetween the two routers.

• How to connect a second router WRT54G

  I can't get a signal through my entire House so I bought a second router WRT54G, running that the Setup disk affects only the first router so how do the other work?

  To connect two routers together, go here.

• 2xCisco 871, 2 tunnels, 2 PSI on second router

  / * Style definitions * / table. MsoNormalTable {mso-style-name : Standardowy ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 cm 5.4pt cm 0 5.4pt ; mso-para-marge-haut : 0 cm ; mso-para-marge-droit : 0 cm ; mso-para-marge-bas : 10.0pt ; mso-para-marge-gauche : 0 cm ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ; mso-fareast-language : EN-US ;}

  I have a task to do.

  Two routers 871 work connected by tunnel by using the simple vpn configuration.

  On the second router is now 2 ISP connections, as a backup.

  How to configure routers to automatically switch VPN tunnel at a time where one of the ISP is down?

  First router:

  Apart from IP: 213.23.34.1

  Second router

  Out of isps1 IP: 58.34.5.225

  Outside ISP2 IP: 199.23.1.231 - backup

  For now I made the route-map for each ISP configuration automatically switch the outer harbour.

  Configured is 2 tunnels, but the other will not work.

  What to do next?

  On the router which has two ISP connections, the tunnel will be always using the primary link.

  That is to say

  If you disable the tunnel, but the main link is still active, then it will again create the tunnel using the primary link.

  If the second link is activated and you erase the tunnel, the tunnel should establish using the secondary link.

  A way to check what is happening is to use:

  Cree debugging isa--> for negotiations of phase 1

  Cree debugging ipsec--> for phase 2

  Federico.

• additional NIC connected to the second router interface does not have IP

  Hi I have an esxi5 running on the hp with two physical NICs micro server that is visible on esxi as vmnic0 and vmnic1. Initially, I was working with vmnic0 as a main network as the interface of management and also VM NIC that is connected to my internet. No problem here. Now, I plugged the second card which is represented as vmnic1 to another router in my house that has its own separate subnet by wire of physics. This second router has its own Dhcp and set up correctly as I connect my mobile phone and tablet that and gets its ip DHCP server. However vmnic1 receives not all IP address. Here is the configuration:

  Phys. netcard vmnic0 192.168.1.254 (obtained from internet router ip) no problems, related to the management network vSwitch0

  Phys. netcard vmnic1? any IP connected to separate vSwitch2, physical network is connected to the router with DHCP with the range 10.0.1.2 10.0.1.1 - 10.0.1.100

  To debug effort, I imported vmnic1 in the virtual machine running on that ESXi and static ip address assigned 10.0.1.101, whereas it falls in the same subnet as the second router and tried to ping router (10.0.1.1) however got "destination unreachable". Obviously ping can't the second router.

  So my question is why? Can anyone help on this?

  I put below the esxi Network Setup:

  Thank you!

  I just pointed it arbitrarily when I created vSwitch2, does not interfere the vSwitch0. 2nd router lacks any setting of vlan.  Should not do and leave the vlan by default? Thank you

• Use the second router to extend the network to Time Capsule

  I have a v7.6.7 running Time Capsule 1 TB and older airport. I'm hoping to add a second router in a new location, and I use an ethernet cable from the TC at the new router (TP Link Archer C5), updated to the latest version of the firmware. The IP address of the TC is 192.168.1.1.

  I have set up my router C5 as follows: allocation of IP 192.168.1.199, value DHCP = off, and I connect a cable between the TC ports and port WAN (not Internet) available on the C5. In the C5 wireless settings, I tried both using the TC SSID and pw and creating a new SSID and pw. In both cases, the network will work for a short time, but eventually the entire network, including the TC, stops working. I made no changes to the parameters of the TC on any trial.

  Is it possible to use a TC and a router not Apple on the same network? If so, what are the right settings for the TC and the secondary router? If not, is it better to have the not Apple as main router and add the TC to the network created by the non-Apple router?

  Is it possible to use a TC and a router not Apple on the same network? If so, what are the right settings for the TC and the secondary router?

  Yes. That would be the basis of a network of mobile type.

  The key for a roaming network parameters are:

  • The 'primary' router must be configured as a router. In other words, it must have active NAT and DHCP services.
  • All other routers used in a network of roaming must be reconfigured as a bridge.
  • All routers must broadcast a Wi - Fi network that uses the same network (SSID, aka) name, and the type of wireless security, and the password.
  • All routers must be interconnected by Ethernet. To provide Powerline adapters using an Ethernet connectivity should also work.

  If not, is it better to have the not Apple as main router and add the TC to the network created by the non-Apple router?

  Should not really which is the main in the roaming network.

  I think at this point, your current circuit line. To check that, I would suggest that you consider to bring back the router C5 in the same room as you have the TC. Then connect it directly to one of the LAN of the TC ports. Complete the entire upward to a mobile network and test it. If everything works, bring back the C5 in the desired location, and then try again.

  If it fails, then the circuit line will be tested to check that it provides a solid 'Ethernet' connection between the adapters.

• Connection with a switch EZXS55W or a second router WRT54G to my router network WTR300N home?

  I have a home office in my basement with my computer connected to a lan of my WRT300N router that is set up on the first floor and networking with three additional computers to the floor as well. I want to add 2 additional computers in my basement and wireless is not a good set upward because the signal strength is very low. I have great reception on the floor and even on the second floor where my children are connected from their rooms. My question is: I have an older WRT54G Router I use is more and want to know if I can connect it to my WRT300N using the lan line ran down in the basement which is connected to one of the Ethernet ports of the WRT300N? If so, how the connection and set up the second router? Also, I can use Ethernet cables to connect my three computers to the second router or what I need to use the wireless of the second router? I was looking at the switch EZXS55W at the Wal-Mart local and thought that was my answer, but after a search through all the answers of the basis of knowledge here, I'm confused on the approach to take and which one would be the best game for me. Here, any help would be great!

  With the EZX you extended your wired LAN. You can still use the WRT54G to add another point for other cable ports and wireless access. Just do these 4 steps as stated in my previous post.

  You can connect the WRT54G the WRT300N or the EZX. Basically, it's all the same. You don't have to turn off the switch before you connect a device.

  If you want to use the additional wireless WRT54G, you can try to set up a roaming wireless network. Implement the WRT with identical settings as on the WRT300N wireless, i.e. identical SSID and wireless security the same (preferably WPA2) personal with a good password. Do not turn off the SSID broadcast on either WRT. Only the allocation of channels should be different at a time to avoid any interference. Now the devices should be able to move from one access point to another without losing the network connection.

  However, if you perform this configuration test carefully. I don't know how it works if you have a N Router and a G. If this does not work, use different SSID on both. You can then choose which SSID to connect to on the client.

• Help! Setup Wizard cannot connect to the router!

  I tried several times to install this router wireless MO # BEFW11S4.

  I get an error message that Setup Wizard cannot connect to the router!

  I pressed the reset on the back button each time, it is turned off, check the cable connections between the modem cable to the router, then router to the computer.

  After dropping out of the router and connect the PC to the top with the modem, the PC is then connected to the internet once more.

  How to solve problems, or isolate the problem as a bad router?

  Please send me a PM for any suggestions or help.

  Thxx

  (Note to mod: Email address removed.)

  Thank you very much this has helped. You don't mention there was a button "generate" to create the password agorythm code to use as a password.

  Thank you! Problem has been resolved.

• VPN between ASA and cisco router [phase2 question]

  Hi all

  I have a problem with IPSEC VPN between ASA and cisco router

  I think that there is a problem in the phase 2

  Can you please guide me where could be the problem.
  I suspect questions ACL on the router, but I cannot fix. ACL on the router is specified below

  Looking forward for your help

  Phase 1 is like that

  Cisco_router #sh crypto isakmp his

  IPv4 Crypto ISAKMP Security Association
  status of DST CBC State conn-id slot
  78.x.x.41 87.x.x.4 QM_IDLE 2006 0 ACTIVE

  and ASA

  ASA # sh crypto isakmp his

  ITS enabled: 1
  Generate a new key SA: 0 (a tunnel report Active 1 and 1 to generate a new key during the generate a new key)
  Total SA IKE: 1

  1 peer IKE: 78.x.x.41
  Type: L2L role: initiator
  Generate a new key: no State: MM_ACTIVE

  Phase 2 on SAA

  ASA # sh crypto ipsec his
  Interface: Outside
  Tag crypto map: Outside_map, seq num: 20, local addr: 87.x.x.4

  Outside_cryptomap_20 ip 172.19.209.0 access list allow 255.255.255.0 172.
  19.194.0 255.255.255.0
  local ident (addr, mask, prot, port): (172.19.209.0/255.255.255.0/0/0)
  Remote ident (addr, mask, prot, port): (172.19.194.0/255.255.255.0/0/0)
  current_peer: 78.x.x.41

  #pkts program: 8813, #pkts encrypt: 8813, #pkts digest: 8813
  #pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0
  compressed #pkts: 0, unzipped #pkts: 0
  #pkts uncompressed: 8813, model of #pkts failed: 0, #pkts Dang failed: 0
  #send errors: 0, #recv errors: 0

  local crypto endpt. : 87.x.x.4, remote Start crypto. : 78.x.x.41

  Path mtu 1500, fresh ipsec generals 58, media, mtu 1500
  current outbound SPI: C96393AB

  SAS of the esp on arrival:
  SPI: 0x3E9D820B (1050509835)
  transform: esp-3des esp-md5-hmac no
  running parameters = {L2L, Tunnel}
  slot: 0, id_conn: 7, crypto-card: Outside_map
  calendar of his: service life remaining (KB/s) key: (4275000/3025)
  Size IV: 8 bytes
  support for replay detection: Y
  outgoing esp sas:
  SPI: 0xC96393AB (3378746283)
  transform: esp-3des esp-md5-hmac no
  running parameters = {L2L, Tunnel}
  slot: 0, id_conn: 7, crypto-card: Outside_map
  calendar of his: service life remaining (KB/s) key: (4274994/3023)
  Size IV: 8 bytes
  support for replay detection: Y

  Phase 2 on cisco router

  protégé of the vrf: (none)
  local ident (addr, mask, prot, port): (172.19.209.0/255.255.255.0/0/0)
  Remote ident (addr, mask, prot, port): (172.19.194.0/255.255.255.0/0/0)
  current_peer 87.x.x.4 port 500
  LICENCE, flags is {origin_is_acl},
  #pkts program: encrypt 0, #pkts: 0, #pkts digest: 0
  #pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0
  compressed #pkts: 0, unzipped #pkts: 0
  #pkts uncompressed: 0, #pkts compr. has failed: 0
  #pkts not unpacked: 0, #pkts decompress failed: 0
  Errors #send 0, #recv 0 errors

  local crypto endpt. : 78.x.x.41, remote Start crypto. : 87.x.x.4
  Path mtu 1452, ip mtu 1452, ip mtu BID Dialer0
  current outbound SPI: 0x0 (0)

  SAS of the esp on arrival:

  the arrival ah sas:

  SAS of the CFP on arrival:

  outgoing esp sas:

  outgoing ah sas:

  outgoing CFP sas:

  protégé of the vrf: (none)
  local ident (addr, mask, prot, port): (172.19.194.0/255.255.255.0/0/0)
  Remote ident (addr, mask, prot, port): (172.19.209.0/255.255.255.0/0/0)
  current_peer 87.x.x.4 port 500
  LICENCE, flags is {origin_is_acl},
  #pkts program: encrypt 0, #pkts: 0, #pkts digest: 0
  #pkts decaps: 8947, #pkts decrypt: 8947, #pkts check: 8947
  compressed #pkts: 0, unzipped #pkts: 0
  #pkts uncompressed: 0, #pkts compr. has failed: 0
  #pkts not unpacked: 0, #pkts decompress failed: 0
  Errors #send 0, #recv 0 errors

  local crypto endpt. : 78.x.x.41, remote Start crypto. : 87.x.x.4
  Path mtu 1452, ip mtu 1452, ip mtu BID Dialer0
  current outbound SPI: 0x3E9D820B (1050509835)

  SAS of the esp on arrival:
  SPI: 0xC96393AB (3378746283)
  transform: esp-3des esp-md5-hmac.
  running parameters = {Tunnel}
  Conn ID: 29, flow_id: Motorola SEC 1.0:29, card crypto: mycryptomap
  calendar of his: service life remaining (k/s) key: (4393981/1196)
  Size IV: 8 bytes
  support for replay detection: Y
  Status: ACTIVE

  the arrival ah sas:

  SAS of the CFP on arrival:

  outgoing esp sas:
  SPI: 0x3E9D820B (1050509835)
  transform: esp-3des esp-md5-hmac.
  running parameters = {Tunnel}
  Conn ID: 30, flow_id: Motorola SEC 1.0:30, card crypto: mycryptomap
  calendar of his: service life remaining (k/s) key: (4394007/1196)
  Size IV: 8 bytes
  support for replay detection: Y
  Status: ACTIVE

  outgoing ah sas:

  outgoing CFP sas:

  VPN configuration is less in cisco router

  access-list 101 permit ip 172.19.194.0 0.0.0.255 172.19.206.0 0.0.0.255 connect
  access-list 101 permit ip 172.19.206.0 0.0.0.255 172.19.194.0 0.0.0.255 connect
  access-list 101 permit ip 172.19.194.0 0.0.0.255 172.19.203.0 0.0.0.255 connect
  access-list 101 permit ip 172.19.203.0 0.0.0.255 172.19.194.0 0.0.0.255 connect
  access-list 101 permit ip 172.19.194.0 0.0.0.255 172.19.209.0 0.0.0.255 connect
  access-list 101 permit ip 172.19.209.0 0.0.0.255 172.19.194.0 0.0.0.255 connect

  access-list 105 deny ip 172.19.194.0 0.0.0.255 172.19.206.0 0.0.0.255 connect
  access-list 105 deny ip 172.19.206.0 0.0.0.255 172.19.194.0 0.0.0.255 connect
  access-list 105 deny ip 172.19.194.0 0.0.0.255 172.19.203.0 0.0.0.255 connect
  access-list 105 deny ip 172.19.203.0 0.0.0.255 172.19.194.0 0.0.0.255 connect
  access-list 105 deny ip 172.19.194.0 0.0.0.255 172.19.209.0 0.0.0.255 connect
  access-list 105 deny ip 172.19.209.0 0.0.0.255 172.19.194.0 0.0.0.255 connect

  sheep allowed 10 route map
  corresponds to the IP 105

  Crypto ipsec transform-set esp-3des esp-md5-hmac mytransformset

  mycryptomap 100 ipsec-isakmp crypto map
  the value of 87.x.x.4 peer
  Set transform-set mytransformset
  match address 101

  crypto ISAKMP policy 100
  BA 3des
  md5 hash
  preshared authentication
  Group 2
  ISAKMP crypto key xxx2011 address 87.x.x.4

  Your permit for 105 ACL statement should be down is changed to match because it is the most general ACL.

  You currently have:

  Extend the 105 IP access list
  5 permit ip 172.19.194.0 0.0.0.255 (18585 matches)
  10 deny ip 172.19.194.0 0.0.0.255 172.19.206.0 0.0.0.255 connect
  30 deny ip 172.19.194.0 0.0.0.255 172.19.203.0 0.0.0.255 connect
  50 deny ip 172.19.194.0 0.0.0.255 172.19.209.0 0.0.0.255 connect

  It should be:

  Extend the 105 IP access list
  10 deny ip 172.19.194.0 0.0.0.255 172.19.206.0 0.0.0.255 connect
  30 deny ip 172.19.194.0 0.0.0.255 172.19.203.0 0.0.0.255 connect
  50 deny ip 172.19.194.0 0.0.0.255 172.19.209.0 0.0.0.255 connect

  IP 172.19.194.0 allow 60 0.0.0.255 (18585 matches)

  To remove it and add it to the bottom:

  105 extended IP access list

  not 5

  IP 172.19.194.0 allow 60 0.0.0.255 any

  Then ' delete ip nat trans. "

  and it should work now.

• setting up a vpn ssl to a netgear router

  I have setup a router netgear FVS336G at a customer and you have configured a vpn ssl to the customer. I can cinnect on a win xp machine, but not on my machine which is running Vista 64 bit. I get narrations of error message cannot install the vpn tunnel.

  Hi Jluequi,

  The issue of Windows 7 you have posted is better suited for the IT Pro TechNet public. Please post your question in the TechNet Windows 7 networking forum.

  Concerning
  Joel S
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• AnyConnect VPN on ASA behind Internet router

  I have script like below and that you need assistance please

  Switch 10.10.1.1/30---> (10.10.1.2/30 inside the Interface) of base ASA (10.10.2.2/30 outside interface)---> public INT router (30.30.30.30/30) (10.10.2.1/30 LAN).

  I have configured the VPN but it needs more setup in the router and the VPN should be the public ip address so outside users can access.

  Fix.

  --

  Please do not forget to select a correct answer and rate useful posts

• Tunnel VPN IPSEC Gre of the router in the branch office by Pix to the router HQ

  Hi all

  I tried to get this scenario to work before I put implement but am getting the error on router B.

  

  01:05:38: % CRYPTO-6-IKMP_MODE_FAILURE: fast processing mode failed with the peer to 83.1.16.1

  Here are the following details for networks

  Router B

  Address series 82.12.45.1/30

  fast ethernet 192.168.20.1/24 address

  PIX

  outside the 83.1.16.1/30 interface eth0

  inside 192.168.50.1/30 eth1 interface

  Router

  Fast ethernet (with Pix) 192.168.50.2/30 address

  Loopback (A network) 192.168.100.1/24 address

  Loopback (Network B) 192.168.200.1/24 address

  Loopback (Network C) 192.168.300.1/24 address

  Is could someone please tell me where im going wrong as I read the explanation of the error and it points to political unmaching. This has confused me like the two counterparts seem to have the same settings.

  Config router B

  ======================

  name of host B
  !
  Select the 5 secret goat.
  !
  username 7 privilege 15 password badger badger
  iomem 15 memory size
  IP subnet zero
  !
  !
  no ip domain-lookup
  IP - test.local domain name
  !
  property intellectual ssh delay 30
  property intellectual ssh authentication-2 retries
  !
  crypto ISAKMP policy 5
  md5 hash
  preshared authentication
  Group 2
  ISAKMP crypto key VPN2VPN address 83.1.16.1
  !
  86400 seconds, duration of life crypto ipsec security association
  !
  Crypto ipsec transform-set esp - esp-md5-hmac VPN
  !
  crypto map 5 VPN ipsec-isakmp
  defined by peer 83.1.16.1
  PFS group2 Set
  match address VPN
  !
  call the rsvp-sync
  !
  interface Loopback10
  20.0.2.2 the IP 255.255.255.255
  !
  interface Tunnel0
  bandwidth 1544000
  20.0.0.1 IP address 255.255.255.0
  source of Loopback10 tunnel
  tunnel destination 20.0.2.1
  !
  interface FastEthernet0/0
  Description * inside the LAN CONNECTION *.
  address 192.168.20.1 255.255.255.0
  IP nat inside
  automatic duplex
  automatic speed
  !
  interface Serial0/0
  Description * INTERNET ACCESS *.
  IP 88.12.45.1 255.255.255.252
  NAT outside IP
  VPN crypto card
  !
  interface FastEthernet0/1
  no ip address
  Shutdown
  automatic duplex
  automatic speed
  !
  Router eigrp 1
  network 20.0.0.0
  No Auto-resume
  !
  overload of IP nat inside source list NAT interface Serial0/0
  IP classless
  IP route 0.0.0.0 0.0.0.0 Serial0/0
  no ip address of the http server
  !
  !
  NAT extended IP access list
  deny ip 192.168.20.0 0.0.0.255 192.168.200.0 0.0.0.255
  deny ip 192.168.20.0 0.0.0.255 192.168.300.0 0.0.0.255
  deny ip 192.168.20.0 0.0.0.255 192.168.100.0 0.0.0.255
  ip licensing 192.168.20.0 0.0.0.255 any
  list of IP - VPN access scope
  permit ip host 20.0.2.2 20.0.2.1
  !

  Config PIX

  ====================

  PIX Version 7.2 (4)
  !
  pixfirewall hostname
  names of
  name 20.0.2.2 B_LOOP
  name 88.12.45.1 B_WANIP
  !
  interface Ethernet0
  Description * LINK to ISP *.
  nameif outside
  security-level 0
  IP 83.1.16.1 255.255.255.252
  !
  interface Ethernet1
  Description * LINK TO LAN *.
  nameif inside
  security-level 100
  IP 192.168.50.1 255.255.255.252
  !
  passive FTP mode
  the ROUTER_LOOPS object-group network
  network-object 20.0.2.0 255.255.255.252
  access allowed extended VPN ip host 20.0.2.1 B_LOOP list
  access-list extended SHEEP permit ip host 20.0.2.1 ROUTER_LOOPS object-group
  Access ip allowed any one extended list ACL_OUT
  pager lines 24
  Outside 1500 MTU
  Within 1500 MTU
  no failover
  ICMP unreachable rate-limit 1 burst-size 1
  don't allow no asdm history
  ARP timeout 14400
  Global (1 interface external)
  NAT (inside) 0 access-list SHEEP
  NAT (inside) 1 192.168.50.0 255.255.255.252
  NAT (inside) 1 192.168.50.0 255.255.255.0
  Access to the interface inside group ACL_OUT
  Route outside 0.0.0.0 0.0.0.0 83.1.16.2 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set esp - esp-md5-hmac VPN
  86400 seconds, duration of life crypto ipsec security association
  VPN 5 crypto card matches the VPN address
  card crypto VPN 5 set pfs
  card crypto VPN 5 set peer B_WANIP
  VPN 5 value transform-set VPN crypto card
  card crypto VPN 5 defined security-association life seconds 28800
  card crypto VPN outside interface
  crypto isakmp identity address
  crypto ISAKMP allow outside
  crypto ISAKMP policy 5
  preshared authentication
  the Encryption
  md5 hash
  Group 2
  life 86400
  Telnet timeout 5
  SSH timeout 5
  Console timeout 0
  tunnel-group 88.12.45.1 type ipsec-l2l
  IPSec-attributes tunnel-group 88.12.45.1
  pre-shared-key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !

  When you create a GRE tunnel between two routers, there should be a routing decision to reach the Remote LAN through local (rather than exit directly the physical interface) tunnel interface.

  This could be accomplished by EIGRP, but you can check if the adjacency is built.

  As a test, what happens if you add a static route saying (reach remote LAN, sending traffic to the tunnel interface).

  Check if the GRE tunnel comes up with sh interface tunnel

  Federico.

• VPN - cannot subnets behind 2nd router internal access. Help.

  Hi guys,.

  Looking for a little help after a day of frustration. I'm really new to this and student so I know I'm doing something stupid. In any case, I bought an ASA 5505 and placed it between my cable Modem and router Cisco 3745. The external interface on the ASA is dhcp, the inside interface is 192.168.100.1. The external interface of the 3745 is 192.168.100.2 and inside is 192.168.1.1. The VPN pool is 192.168.200.10 - 192.168.200.10.

  These are the problems...

  1. when I set up a VPN to ASA session, I can ping and access resources dierectly connected to interfaces of the ASA and the 192.168.100.0 internal ASA network. However, I can't access any resource behind the 3745. I can't even ping 192.168.1.1.

  2. Although I believe I sent split tunnel, I can't turn to the internet when connected to the VPN.

  Here's my network and my config ASA topology and router config...

  ASA...

  ASA Version 8.2 (5)

  !

  poog-fw1 hostname

  Poog domain name

  activate the password * encrypted

  encrypted

  names of

  name 192.168.100.2 RouterWAN

  internal name 192.168.100.0

  name 192.168.200.0 VPN

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 192.168.100.1 address 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP address dhcp setroute

  !

  boot system Disk0: / asa825 - k8.bin

  passive FTP mode

  DNS lookup field inside

  DNS domain-lookup outside

  DNS server-group DefaultDNS

  Server name 167.206.245.129

  Server name 167.206.245.130

  Poog domain name

  permit same-security-traffic intra-interface

  object-group, VPN network

  the RouterWAN object-group network

  object-group network RouterWAN-01

  object-group network RouterWAN-02

  object-group network RouterWAN-03

  object-group network RouterWAN-04

  object-group network RouterWAN-05

  the obj_any object-group network

  network of subject-group obj_any-01

  object-group network obj - 0.0.0.0

  object-group network iphone

  object-group Protocol TCPUDP

  object-protocol udp

  object-tcp protocol

  outside_access_in list extended access permitted tcp VPN 255.255.255.0 everything

  Comment from outside_access_in-Telnet access on the router list

  outside_access_in list extended access permit tcp any interface outside eq telnet

  Comment from outside_access_in-access IP cameras list

  outside_access_in list extended access allowed object-group TCPUDP any interface apart from 1021 1022 range

  outside_access_in list extended access permit tcp any interface outside eq www

  Comment from outside_access_in-list of FTP access to NAS

  outside_access_in list extended access permit tcp any interface outside eq ftp

  Comment from outside_access_in-VNC server WX access list

  outside_access_in list extended access permit tcp any interface outside eq 5900

  outside_access_in list extended access permit tcp any interface outside eq https

  Comment from outside_access_in-Telnet access on the router list

  Comment from outside_access_in-access IP cameras list

  Comment from outside_access_in-list of FTP access to NAS

  Comment from outside_access_in-VNC server WX access list

  AnyConnect_Client_Local_Print list extended access permit tcp any any eq lpd

  Note AnyConnect_Client_Local_Print of access list IPP: Internet Printing Protocol

  AnyConnect_Client_Local_Print list extended access permit tcp any any eq 631

  print the access-list AnyConnect_Client_Local_Print Note Windows port

  AnyConnect_Client_Local_Print list extended access permit tcp any any eq 9100

  access-list AnyConnect_Client_Local_Print mDNS Note: multicast DNS protocol

  AnyConnect_Client_Local_Print list extended access permit udp any host 224.0.0.251 eq 5353

  AnyConnect_Client_Local_Print of access list LLMNR Note: link Local Multicast Name Resolution protocol

  AnyConnect_Client_Local_Print list extended access permit udp any host 224.0.0.252 eq 5355

  Note access list TCP/NetBIOS protocol AnyConnect_Client_Local_Print

  AnyConnect_Client_Local_Print list extended access permit tcp any any eq 137

  AnyConnect_Client_Local_Print list extended access udp allowed any any eq netbios-ns

  AnyConnect_Client_Local_Print deny ip extended access list a whole

  Note AnyConnect_Client_Local_Print of access list IPP: Internet Printing Protocol

  print the access-list AnyConnect_Client_Local_Print Note Windows port

  access-list AnyConnect_Client_Local_Print mDNS Note: multicast DNS protocol

  AnyConnect_Client_Local_Print of access list LLMNR Note: link Local Multicast Name Resolution protocol

  Note access list TCP/NetBIOS protocol AnyConnect_Client_Local_Print

  inside_nat0_outbound to access extended list internal ip 255.255.255.0 allow VPN 255.255.255.0

  standard access-list internal split tunnel permit 255.255.255.0

  host of standard splitting allowed access list 192.168.1.0 tunnel

  pager lines 24

  Enable logging

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  local pool VPNPOOL 192.168.200.10 - 192.168.200.20 255.255.255.0 IP mask

  IP verify reverse path to the outside interface

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm - 647.bin

  don't allow no asdm history

  ARP timeout 14400

  NAT-control

  Overall 101 (external) interface

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 101 0.0.0.0 0.0.0.0

  public static tcp (indoor, outdoor) interface telnet RouterWAN telnet netmask 255.255.255.255

  static (inside, inside) tcp 5900 5900 RouterWAN netmask 255.255.255.255 interface

  public static tcp (indoor, outdoor) interface ftp RouterWAN ftp netmask 255.255.255.255

  1021 RouterWAN 1021 netmask 255.255.255.255 static interface tcp (indoor, outdoor)

  static (inside, inside) tcp 1022 1022 RouterWAN netmask 255.255.255.255 interface

  Access-group outside_access_in in interface outside

  !

  router RIP

  internal network

  default information are created

  version 2

  No Auto-resume

  !

  Route inside 192.168.1.0 255.255.255.0 RouterWAN 1

  Route inside VPN 255.255.255.0 192.168.100.1 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  Enable http server

  http internal 255.255.255.0 inside

  http VPN 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  Telnet internal 255.255.255.0 inside

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  dhcpd outside auto_config

  !

  dhcpd address RouterWAN-RouterWAN inside

  dhcpd auto_config outside interface inside

  dhcpd allow inside

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  allow outside

  SVC disk0:/anyconnect-macosx-i386-2.4.1012-k9.pkg 1 image

  enable SVC

  tunnel-group-list activate

  attributes of Group Policy DfltGrpPolicy

  value of server DNS 167.206.245.129

  Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn

  Split-tunnel-network-list value split tunnel

  internal Clientless group strategy

  attributes without Group Policy client

  VPN-tunnel-Protocol webvpn

  WebVPN

  the value of the URL - list VPN_Book_Marks

  internal AnyConnect group strategy

  attributes AnyConnect-group policy

  Welcome To My Network Banner value

  value of server DNS 167.206.245.129

  VPN-tunnel-Protocol svc webvpn

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list no

  Poog value by default-field

  WebVPN

  the value of the URL - list VPN_Book_Marks

  SVC Dungeon-Installer installed

  SVC request no svc default

  username ogonzalez encrypted password privilege 0 0VrbklOhGRHipw79

  username ogonzalez attributes

  Clientless VPN-group-policy

  username ymcpO334smdskkpl encrypted password privilege 0 jgonzalez

  jgonzalez username attributes

  AnyConnect VPN-group-policy

  type tunnel-group RAVPN remote access

  attributes global-tunnel-group RAVPN

  address VPNPOOL pool

  tunnel-group RAVPN webvpn-attributes

  enable RAVPN group-alias

  allow group-url https://69.121.142.156/RAVPN

  tunnel-group AnyConnect type remote access

  tunnel-group AnyConnect General attributes

  address VPNPOOL pool

  strategy-group-by default AnyConnect

  tunnel-group AnyConnect webvpn-attributes

  enable AnyConnect group-alias

  allow group-url https://69.121.142.156/AnyConnect

  tunnel-group type Clientless Remote access

  tunnel-group Clientless General attributes

  Clientless by default-group-policy

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  !

  global service-policy global_policy

  context of prompt hostname

  no remote anonymous reporting call

  call-home

  Profile of CiscoTAC-1

  no active account

  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

  email address of destination [email protected] / * /

  destination-mode http transport

  Subscribe to alert-group diagnosis

  Subscribe to alert-group environment

  Subscribe to alert-group monthly periodic inventory

  monthly periodicals to subscribe to alert-group configuration

  daily periodic subscribe to alert-group telemetry

  Cryptochecksum:7d91e2ad8d7a86c40860fa8a1b117271

  : end

  Router...

  Current configuration: 1922 bytes

  !

  version 12.3

  horodateurs service debug uptime

  Log service timestamps uptime

  no password encryption service

  !

  hostname poog_rtr1

  !

  boot-start-marker

  boot-end-marker

  !

  no set record in buffered memory

  no console logging

  no logging monitor

  enable secret 5 *.

  !

  No aaa new-model

  IP subnet zero

  !

  !

  IP cef

  no ip domain search

  DHCP excluded-address IP 192.168.1.1 192.168.1.150

  !

  IP dhcp DHCP1 pool

  import all

  network 192.168.1.0 255.255.255.0

  default router 192.168.1.1

  DNS-server 167.206.245.129 167.206.245.130

  !

  !

  !

  !

  !

  !

  !

  !

  !

  !

  !

  !

  username * password privilege 15 0 *.

  !

  !

  !

  !

  interface Loopback0

  IP 1.1.1.1 255.255.255.255

  !

  interface FastEthernet0/0

  LAN description

  IP 192.168.1.1 255.255.255.0

  IP nat inside

  automatic duplex

  automatic speed

  !

  interface FastEthernet0/1

  WAN description

  DHCP IP address

  NAT outside IP

  automatic duplex

  automatic speed

  !

  router RIP

  version 2

  network 192.168.1.0

  network 192.168.100.0

  network 192.168.200.0

  No Auto-resume

  !

  IP nat inside source list 1 interface FastEthernet0/1 overload

  IP nat inside source static tcp 192.168.1.100 80 interface FastEthernet0/1 80

  IP nat inside source static tcp 192.168.1.13 5900 interface FastEthernet0/1 5900

  IP nat inside source static tcp 192.168.1.12 1022 interface FastEthernet0/1 1022

  IP nat inside source static tcp 192.168.1.11 1021 interface FastEthernet0/1 1021

  IP nat inside source static tcp 192.168.1.100 21 interface FastEthernet0/1 21

  IP nat inside source static tcp 192.168.1.1 23 interface FastEthernet0/1 23

  IP http server

  local IP http authentication

  IP classless

  IP route 192.168.200.0 255.255.255.0 FastEthernet0/1

  !

  !

  Remark SDM_ACL category of access list 1 = 16

  access-list 1 permit one

  not run cdp

  !

  !

  !

  !

  !

  !

  !

  Dial-peer cor custom

  !

  !

  !

  entry door

  !

  Banner motd ^ C

  UNAUTHORIZED ACCESS IS STRICTLY PROHIBITED! *****^C

  !

  Line con 0

  line to 0

  line vty 0 4

  local connection

  !

  end

  "192.168.100.0---> 192.168.1.0 I DO NOT get ping responses."

  Please add "inspect icmp" in politics of inspection_default class as shown below.

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  inspect the icmp

  I hope this helps.

  Evaluate the useful ticket.

  Thank you

• VPN - Pix 515e for Cisco router

  I have the following Setup and I can't seem to get the next tunnel. My end is a PIX 515e race 7.2 (4). The other end is a Cisco router-not sure of the model or version of the IOS.

  PIX:

  90 extended access-list allow ip host a.a.a.a host b.b.b.b

  NAT (inside) - 0-90 access list

  correspondence address card crypto mymap 20 90
  card crypto mymap 20 peers set x.x.x.x
  map mymap 20 set transformation-strong crypto
  mymap outside crypto map interface
  ISAKMP crypto identity hostname
  crypto ISAKMP allow outside
  crypto ISAKMP policy 8
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400

  tunnel-group x.x.x.x type ipsec-l2l
  tunnel-group ipsec-attributes x.x.x.x
  pre-shared key 12345

  Router:

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-margin : 0 ; mso-para-marge-bottom : .0001pt ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;} / * Définitions de style * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-margin : 0 ; mso-para-marge-bottom : .0001pt ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}

  SDM_5 extended IP access list

  permit ip host b.b.b.b host a.a.a.a

  ISAKMP crypto key 12345 address y.y.y.y no.-xauth

  map SDM_CMAP_1 5 ipsec-isakmp crypto

  Description vpn for laboratory

  defined peer y.y.y.y

  game of transformation-ESP-3DES-SHA

  match address SDM_5

  I'm running him debugs following:

  Debug crypto ipsec enabled at level 1
  ISAKMP crypto debugging enabled at level 1

  I get the following debug output:

  August 16-04:16:10 [IKEv1]: IP = x.x.x.x, counterpart of drop table counterpart, didn't match!
  August 16-04:16:10 [IKEv1]: IP = x.x.x.x, error: cannot delete PeerTblEntry

  Isa HS her

  IKE Peer: x.x.x.x
  Type: user role: initiator
  Generate a new key: no State: MM_WAIT_MSG2

  Any ideas?

  Thank you

  Dave

  If you see the MM_WAIT_MSG2, which means that her counterpart (the other side) does not answer and this side where you can see the status MM_WAIT_MSG2 sent the first message IKE, however, did not hear of the peer.

  You can check if UDP/500 is stuck on the way between the 2 sites.

  Try running traffic on the other side and see if you also get the same status of MM_WAIT_MSG2. If you do, that confirms 100% 500/UDP is blocked on the way between the 2 sites.