3510 printer: direct internet windows wireless printer

just to check: on my WIN 7 PC, I cannot not BOTH

Print via direct wireless (WD) on my 3510


internet access on my network (WHN) wireless home

i unless:

(using WIN 7) switch between the WD network and the network WHN


manually disable WD on the 3510?

This is inherent in the implementation of WIN7/WD?  Yes/No?


Indeed by connecting to the Direct wireless network you will have no access to the internet, it is an expected behavior:

Wireless connection issues > How do I print wirelessly without a wireless router? > Downsides to peer-to-peer networking:

Your computer can only connect to one wireless network at a time. When it is connected to your printer, it cannot also connect to a wireless router (for Internet access, for example).


To obtain the complete network features, need you a router to connect to the printer and the internet.


Tags: HP Printers

Similar Questions

  • I have windows 8 and can had a 651 error trying to connect to my Internet verizon wireless. Any ideas on how to solve this problem?

    I have windows 8 and can had a 651 error trying to connect to my Internet verizon wireless. Any ideas on how to solve this problem?

    This response may be a sound-end 2015 years.

    But in the case where some people have this problem I had.

    Correction on wireless W8.1 as follows,

    Find/locate connection network in "charms."

    Right click on Wi Fi - select DISABLE-wait a minute then

    RT click on Wi - Fi to ACTIVATE.

    Connect to your internet service provider when you see your SSID.

    Also a note if your printer or the wireless on cpu receiver

    Activate Bluetooth.

    I hope this helps.

  • enable windows wireless connection manager

    I am installing a new wireless router, the installation disc tells me to activate windows wireless connection manager, how can I do this? Thnks


    What is the brand and model of the computer?

    Follow these steps and check.

    a. click Start and then click Control Panel.

    b. click on network connections and Internet.

    c. click on network connections.

    d. right click on the wireless connection icon and choose Activate. (If already activated, proceed to the next step)

    e. right click on the wireless network connectionicon, and then click Properties.

    (f) at the top of the window, click the wireless networks tab.

    g. check Use Windows to configure my wireless network.

  • How to install a windows wireless connection?

    I have a Dell with a dell wireless connection. I bought a cisco linksys e1500 modem works with a windows wireless connection. How to install a windows wireless connection?


    -What exactly happens when you try to connect to the internet?
    -Do you get any error message or error code?
    To fix your problem, try the following methods one by one.

    Alternatively, you can check the link for more information on this below.

    Method 3: here is a link that gives you more information about the router E1500.

    I hope this information helps you!
  • I can't seem to Windows wireless on Lenovo laptop to recognize a USB connection and turn on the wireless radio.

    I use a USB connection to my mobile phone for my internet connection. I want to use wireless mobile radio to connect other devices, but the window wireless services does not recognize that I am connected to the internet. What can I do here, gurus?


    Please contact Microsoft Community.

    1 have you checked the State of the wireless autoconfiguration WLAN service in the services window?
    2. do you have any security software installed on the computer?
    3. have you made changes on the computer recently?
    We will first try to manually start the wireless service, i.e. the WLAN AutoConfig service. To do this, connect to the computer as an administrator.
    1. Click Start, type services.msc and press to enter.
    2. Locate the autoconfiguration WLAN service, double-click to open its properties window.
    3. on the general tab, change the startup type to automatic and click on the Start button.
    4. click on apply, then ok.
    Try to connect to the wireless connection and check the result.
    If the service still does not start, run the System File Checker tool to scan the computer for the corrupt system files and automatically correct. To run a sfc scan, try the steps mentioned in this link: http://support.microsoft.com/kb/929833
    For more information on the wireless settings, see this link: http://technet.microsoft.com/en-us/library/bb878035.aspx
    Let us know the result of the above troubleshooting steps so that we can discuss in detail and help you further.

    If the problem persists, proceed from the link below to fix this problem


    Reply to the post with an up-to-date report of the issue so that we can help you further.

  • Wireless connection error - error 193:Oxc1 - Windows wireless service does not work

    I have a Dell Studio XPS until yesterday worked fine. I plug in a memory (USB) card and that's when the problem occurred.

    Today when I started, it connect to internet via WiFi. The map shows in Device Manager and are passed through controls to enable the automatic. Wired connection is not a problem that's just a very long Ethernet run and WiFi was better. I have other computers on the network, there is a problem with what I think is that the registry is corrupted. It seems that the Wireless LAN and audio are butting heads as the audio is displayed as an X when I try to fix the connection.

    On the bottom bar on Windows 7, it shows a signal with an X on it. Help, please!

    Windows Wireless Service is not running

    Error 193:Oxc1

    Thank you


    Please perform a clean boot mode, press Windows key + R on your keyboard and type services.msc. Access to services that are defined as disabled and edit them in the manual.

    Restart your computer (stay in a clean boot) and return to services.msc. Do not open any other application or browser. Any device that is set to automatic, but it is not started, change its startup type to manual. Any application that is manual, but is started, the change automatically.

    I also recommend that run you check disk, to check for any errors/bad hard disk sectors.

    How to run the disk check


    Thank you



    My Sony VAIO E Series windows wireless service does not

    the computer says that

    Hi Isabel,.

    1. Exactly when you receive this message? It's trying to access wireless internet?
    2. What is the exact model of your PC laptop Sony Vaio E series?

    Make sure that the laptop wireless switch is turned on.

    Method 1:

    Please follow the steps to start the WLAN service.

    1. Press the Windows key and R together to open run prompt and type services.msc
    2. Select the autoconfiguration WLAN service in the list, right-click on properties
    3. Change the startup type to automatic
    4. Click the Start button
    5. Click on apply, Ok.
    6. Restart the computer and check if it works.

    If the problem persists, proceed from the link below to fix this problem.

    Wireless and wired network problems.


    Reply to the post with an up-to-date report of the issue so that we can help you further.

  • Windows 7 Premium: windows wireless services does not

    I am running Windows 7 premium. When I try to connect to the internet it says that windows wireless service does not not need help solve the problem...


    1. What is the full error message?

    2. who is the antivirus installed on the computer program?

    I suggest you to perform the steps mentioned by ' Waseemulla Shariff said on February 11, 2010' a similar discussion.»

    Windows wireless service is not running on this computer


    Note: It is for Windows 7.

    Hope this information helps. Response with status so that we can help you.

  • No access access/Limited - no access Internet (Windows 7)


    I was lucky enough to win a laptop in a competition and I'm having a problem connecting to the internet.

    All I ever get is a limited access (which is basicallly no access) and need help.

    If I enter the comnad prompt and type ipconfig I get

    • Autoconfiguration IPv4 address:
    • subnet mask:

    I know that the addess ip of my router is, then I tried to set it as a default gateway but it makes no difference.

    I have three cards. Connection mobile broadband (Qualcomm Gobi 2000), Wi - Fi Connection Netwrok (Atheros AR9285) & 2 wireless network connection (Microsoft Virtual Wifi). Of the three on the Atheros seems to try to connect (it shows an excellent signal strength) so I have that he has updated the driver and it does.

    I don't know what else I can try. Can anyone suggest anything?

    Thanks in advance.



    There is something that is blocking the connection to the router.

    Please follow this process.

    There is an inherent Catch22 to attempt to repair a computer wireless through wireless. Given that the without wire is not connected to the source, there is no interaction between the wireless source and the Wireless Client and no frame of reference to find what works and what does not.

    As a first step, I will temporarily move the computer to a place close to the wireless router and plug with a wire.

    When he works with a wire, switch Off the Wireless Security in the router, disconnect the wire and try to make wireless work. This must be done when the computer is always close to the wireless router to compensate for the weak, and or blocked the signal that could be part of the problem in the new suite spot work.

    In the computer itself.

    Most laptops have a physical switch for the wireless card. Read the manual of the computer and make sure that the wireless adapter is on.

    Check the Device Manager for the wireless card valid entry.


    If there is no valid entry, remove any entry from fake and re - install the drivers for the wireless card.

    Check network connections to make sure that you have a network icon/entry wireless connection, and that the properties of the icon (right-click on the icon) are correctly configured with the TCP/IPv4 protocol in the properties of network connections.


    Make sure that if there is Wireless Utility a utility vendor is not running with the native Windows wireless utility.

    Make sure you firewall No. preventing / blocks wireless components to join the network.

    Above everything is OK and it connects to the wireless router. Log in from any computer which is, or can be connected to the router with a wire wireless, disable wireless security, make sure that the wireless streaming is enabled and try to connect with no. wireless security.

    When the work turns on the Wireless security.

    Note * people sometimes make mistakes in writing and retype the password for security.

    Another way is to copy in the menu of the router and then paste it when asked of the wireless card.

    Jack-MVP Windows Networking. WWW.EZLAN.NET

  • Unable to connect to internet via wireless router

    Original title: router Question through the network


    Basically, I use NET connection of type PP - Poe, that requires a user name & password to connect. I have 1 Mbps plan of development. recently, I bought a D-link wireless router.
    Connectivity is as---> main internet cable in this way will my internet port of the router. One cable goes on my desk from the LAN1 router lan port. I have configured my router with all the necessary parameters saved & now when I start my computer I dnt need to put the user name and password to connect to the internet.
    I is automatically connected to my network using the router I think.
    Now, the problem is that I use it more than 3 to 4 months. but now, when I start my pc, the network icon on the keep the taskbar on the search for the network all the time.
    Oh, I can't do something, or I can use my cursor also because I move my cursor, but cannot use it. Thus, in this condition I vigorously shutdown my pc, the turnoff to my router & then I start my pc. so if I want to connect to the network, I remove the mains cable and the plugin on my office lan and evrything port works fine. in this State I put the user name and password to connect to the internet.
    SO the thing is these days each time, I keep my router IT and start my pc to the Dungeon of the taskbar, the network icon on the turning points for an unlimited period.
    then, when I am facing this problem I keep my pc WE & the turnoff to my router, then after some time the icon bar of the tasks of the network stop (research or rotation) and it's yellow exclamation point. then use the internet I remove the cable main network from the router and connect to my office. He asks username and password then the connection works fine.
    I am using windows 7 ultimate 64-bit.
    still a very strange thing is when I'm dealing with this network icon turning question I connect my cell phone to my wi - fi router & it works well, but the scenario with my office is the icon itself keep turning. I use a basic wireless router. model No.:. DIR-524.
    I hope, I tried my best to explain my problem.
    waiting for the answer.


    First of all, make sure that you have the latest drivers installed for the network card.

    I can suggest you to run the network troubleshooter and check.

    Using the troubleshooter from network in Windows 7


    Method 2:

    Windows wireless and wired network connection problems


    Method 3:

    Why can't I connect to the Internet?


    Hope this helps and keep us posted.

  • The WLAN button ' does not ' Windows Wireless config does not either

    I just reinstalled Windows XP on the PC of the client after a hard disk failure, but I can't get the laptop to work wireless. I installed the adapter of Intel 2200BG correctly & wireless windows zero configuration "works" according to control panel/admin tools/services, but the Windows wireless configuration icon isn't there & free Toshiba config utility tells me to "change the wireless adapter", but neither the switch on the left side of the laptop or the function & F8 key makes no difference.

    I got probably a thousand or more PC, but I am baffled by this. Any suggestion would be appreciated gratefully.

    Regards, Alan.

    > I correctly installed the adapter Intel 2200BG & wireless windows zero configuration "works" according to control panel/admin tools/services, but the Windows wireless configuration icon isn't there

    You are two possibilities to configure the WiFi network;
    (1) you can use the clean windows zero configuration settings
    (2) you can use the Intel ProSet utility

    When you use the Intel Proset, you must turn off the clean windows zero configuration settings.
    You can do this in the network-> connection WLan network connections

    In the WLan network connection properties, you can enable the option called display the icon in the notification area when connected.
    This would enable the WLan icon in the taskbar.

    PS: What laptop do you have?

  • Cannot get my Satellite Pro to work with internet access wireless

    I have a Satellite Pro L20 - who has wireless network adapter. Bought a BT Voyager 2110 Wireless ADSL router. Connected to my broadband router. Used Toshiba config to find router on my laptop - it looks like I have then drag the icon of the laptop to the router but it says I can't do because the router is used by another owner?
    Should I do anyting - Inter adapter card in my laptop says activated - the router is connected - but nothing works.
    Please help but I'm pretty useless on these things so keep it clear
    Thank you


    Is this the result even when you use the settings Windows wireless?

  • Internet OK wireless access in public libraries, but not at home with Telus V1000H

    My laptop Toshiba Satellite A10 makes Internet connection wireless, no problem, when I use it in our Edmonton public library. But at home where we service Telus high speed, I need to plug the V1000H (Telus modem?) to make it work. A Tech. TELUS tried his laptop home, his has worked.

    I tried the solution in the Toshiba Web site but cannot go very far! The laptop model is PSA 10 C - 05 HVM.

    I would be grateful for any suggestion, thank you.


    Update the NIC drivers and check:


  • Can I use xbox 360 Wireless & the windows wireless receiver so that I can use two controllers in Windows?

    Original title: Wireless 360 controller.

    I bought the gamepad 360 Wireless for windows and it works fine. I also have an xbox for xbox 360 wireless controller. Can I use with the receiver windows wireless so I can use two controllers in windows? When I click on the Green x button it keeps just Charlotte. Is it possible to connect to windows?

    Thank you. In fact, I installed this software already, but thanks for the tip. It turns out that I had to click the button of synchronization on the top of the controller AND the usb thing. I think I was just clicking on the USB thing. Now, it works fine. It's never the best stick for windows. THX.  :)

  • I unchecked the "notify me when this connection is limited or no connectivity" for my windows wireless and LAN connections, but the icons still appear in sys tray when it is disconnected.


    I use my Intel client to manage my wireless network connection in Windows XP Pro SP3. (I need to use the Intel client because it supports protocols wireless not supported by the Windows client).

    I would like to remove the icon from the system tray/notification area Windows wireless network connection and cannot find a way to do it.

    I opened the network connections, right click and choose 'properties' and in the general tab at the bottom there are two check boxes "Show icon in notification area when connected" and "notify me when this connection is limited or not connectivity ' which I disabled (I did it for my local network also), but the icons still appear in the status bar when it is disconnected.

    Any suggestions?
    Thank you

    I found a registry change that removes the icon in the systray.  One needs only to remove these keys (save the first):

    [HKEY_CLASSES_ROOT\CLSID\ {7007ACCF-3202-11D1-AAD2-00805FC1270E}]

    [\DefaultIcon HKEY_CLASSES_ROOT\CLSID\ {7007ACCF-3202-11D1-AAD2-00805FC1270E}]

    [HKEY_CLASSES_ROOT\CLSID\ {7007ACCF-3202-11D1-AAD2-00805FC1270E} \InProcServer32]

Maybe you are looking for