4000 TL is not detection of the bands write, which is design protected?

Similar Questions

• Satellite U500 - 1 DR series Notebook is not detected by the TOSHIBA site

  Hey,.

  My Toshiba Satellite U500 - 1DR Series notebook (Serial No. 1A058758R) is not detected by the automatic detection of TOSHIBA online system. When trying to get portable detected manually on the site, I stopped fingd the model (Satellite U500-1 DR) is listed in the list of available templates or models. I'm unable to download software/updates on the site.

  Hello

  If the work of autoetection doesn t you can find manually but not not using the name model but the model reference number. Your DR U500-1 has part number PSU9ME-xxxxx then please check under http://eu.computers.toshiba-europe.com/innovation/download_drivers_bios.jsp Toshiba download page and look for Satellite U500 with reference number or model number short PSU9ME.

  Can find you it?

• Satellite M30x + Win7: DVD not detected by the CD/DVD drive

  Hello

  I use a M30x since 2004 with its CD/DVD drive * a S mat. DVD-RAM UJ-831
  When I was with Windows XP, I have never had problems to read or write on CD, CD - R, DVD, DVD - R or DVD - RW. But recently I installed windows seven, and since that day the drive won't recognize the DVD. I can still read and burn CDs and CD - R. I'm burning the same Virgin DVD-+ R/RW as before, but the drive won't detect them. Those I have already burn are not detected or the other.
  My computer says that the CD/DVD drive work properly and drivers are up to date.
  I tried to clean the lens, but nothing has changed. And I tried to reinstall the drivers, but I could not found for windows seven.

  Thanks for the help.

  Hello

  Have you tried to delete the upper and lower registry Filters >
  Pleas check it!
  http://support.Microsoft.com/kb/270008/en-us

  You will find the registry key where filters must be removed.

• HARD drive not detected in the BIOS on Satellite A215

  Hi all

  I could use to solve this problem: bought this laptop computer without a disk of the auction. Installed again 2.5 inches HDD SATA 250 GB, which was not detected in BIOS and also not detected when using a MS Vista installation disc. When trying to install Vista, get a message no drive seen HARD and demand for pilots.
  I flashed the BIOS with version (2.0) of lates without problem through the CD drive, but still no detection of HARD drive.

  The drive partitioned and formatted NTFS without problem by using another computer and USB SATA adapter using the command line method. Just for additional verification, I went on the new HARD drive to an extra 2.5 "SATA HDD used for backups, but that the HARD drive has also not been detected.

  It is not a "compatibility" option in CMOS to select SATA or Auto, etc..
  There is not a second HDD, so this isn't a question of slave/primary. There are no jumpers on the new HARD drive.
  Set the CMOS settings 'by default' does not solve the problem.

  The SATA connectors on the HARD drive and laptop computer are in perfect condition.
  Also, the drive is not detected on the laptop connected via USB to SATA Adapter, but of course there is no OS installed to support this connection.

  In any case, I just can't come up with any more ideas to try.
  Any suggestions would be really appreciated!

  Best,
  Glenn

  Hello

  The BIOS should recognize the HARD disk even if the SATA mode would be compatible or AHCI. This should not affect the recognition of the HARD drive.

  You said that you have tested the condition of the HARD drive and it's ok, so I guess that it s no disc HARD question.
  Hmm, you could try to format the HARD drive once more and then connect the portable computer HARD drive.

  Another idea: Remove/Disconnect the CD/DVD drive and then connect the HARD drive to the SATA connector.
  If it does not, then I recommend to test another HARD drive, otherwise if the new HARD drive would not work, then a SATA controller may be defective.

• Digital mp3 player is not detected on the computer.

  Original title: my phone dosnt recognize my drive digital mp3. When I plug it into the usb port do not get an icon. so I can't load music can help you

  MY LAPTOP DOES NOT RECOGNIZE MY MP3 DIGITAL PLAYER. WHEN I PLUG IT INTO THE USB PORT I DON'T GET THE USUAL ICON. SO I CAN'T DOWNLOAD MUSIC ON IT. CAN YOU HELP ME PLEASE

  Hello

  Thanks for posting your question in the Microsoft Community Forums!

  If I understand the question, digital mp3 player is not detected on the computer. Please let me know if this is not correct.

  Before I continue with the troubleshooting steps I may need a few more details to better understand the issue.
  1. what operating system do you use?
  2. do you receive any error messages?
  3. are you having the same problem with other USB devices?
  4. have you tried plugging the machine into the other USB Ports?
  5. did you of recent changes on the computer before this problem?
  6. What is the serial number and model of the MP3 player?
  Method 1:
  We will first try to plug in other USB Ports and on another computer to make sure that there is no problem with the digital mp3 player.
  Method 2:
  If the first method does not resolve the problem, run the hardware and devices Troubleshooter and check if it helps.
  Hardware devices do not work or are not detected in Windows
  http://support.Microsoft.com/mats/hardware_device_problems/en-us
  For more information, please see the link.
  Tips for solving problems of USB devices
  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-solving-problems-with-USB-devices
  Respond with the required information so that we can help you solve the problem.

• DVD rom not detected in the Bios & windows

  Mr President, in my computer the dvd rom is not detected in the Bios & windows. Send me a PSE with solution please.

  Hello

  1. which version of the windows operating system is installed in the computer?

  2. What is the brand and model of the computer?

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  http://support.Microsoft.com/kb/982116

  Important this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  322756

  (http://support.microsoft.com/kb/322756/)

  How to back up and restore the registry in Windows

  I also suggest you to connect with the computer manufacturing and update drivers for BIOS.

• Need still restarts desktop Acer Aspire - keyboard not detected at the login screen

  Hello

  I have Acer Aspire ATC-605-UR13.

  In the course of the last 4 weeks, suddenly the keyboard is not detected at the login screen. The mouse works.

  Still, I have to restart to make the keyboard work.

  Any idea of what caused it? Perhaps any software installed that do?

  P.S.: Btw, I tried a new keyboard, the same behavior. I have concluded that this is not the keyboard.

  Thank you!

  This problem has been reported after that install some recently released update of windows... Currently the ability to perform a restore of the system to an earlier date. You can also try to uninsatlling updates of windows manually from Control Panel > windows update.

• HP X 360: hardware virtualization enabled in the BIOS but not detected by the installation of Intelhaxm.exe

  Hi all

  I'm trying to get Android studio works on my 360. Everything is fine until you try to run virtual device/emulator.

  This does not work because the Virtual Machine is required. When I looked in the BIOS I was surprised to see this small handbook has the functionality that has been disabled.

  I now activated but still not detected by the software. Can anyone help with this?

  See you soon

  The problem was Avast antivirus. I uninstalled and hey presto, intelhax went very well.

• Video card GeForce GTX 660 not detected by the motherboard Windows 7

  I recently upgraded my PC with an Asus z97 - a motherboard and processor Intel i5 4. After the reinstallation of Windows 7, I was able to get a signal from my video card 660 geforce gtx for a few hours. After Windows install several updates, however, I am unable to use my video card without receiving an ENTRY NOT FOUND both of my monitors. My video card is also not appearing in Manager devices, or BIOS and use rather Intel HD Graphics. Cause of the undetected video card, I am unable to install the latest drivers for my card and I have no idea what to try next. I also made sure my current diet provides enough power for the card. Is powered without a doubt the map because the fans spinning, I'm positive that I've attached all required power cables, and the card is inserted completely into the motherboard. I tried all PCI-E ports in my motherboard, but it continues to not display. I tried to install the drivers manually, but the video card should be detected before this is possible. Any help would be greatly appreciated.

  My specs:

  ASUS card mother Z97 - A

  Videocard GeForce GTX 660

  Intel i5 processor 4

  8 GB RAM

  700W ATX power supply

  I should point out that I have tried almost every technical troubleshooting that I have met, with the exception of disabling Intel HD Graphics. I fear that if, due to there not being any trace of my video card in the BIOS and Device Manager, if I disable this will also lose signal from the motherboard of DVI and HDMI, ports that are what I currently use.

  Hello

  As the graphics card is not detected by the motherboard, you will need to contact Asus for more help on this issue. You will need to check if the graphics card is detected in the BIOS or not, if not then contact the computer manufacturer is the right point of support.

  Support from Asus: http://www.support.asus.com/

  Please do not hesitate to visit our Web site for any help with the Windows operating system.

• "Setup could not detect all the printers.

  I've recently set up a new computer and the network.  The host computer is running Vista.  I have connected a Deskjet 6940 via an ethernet cable into the Linksys router and can print from the host computer.

  I have a laptop which is under XP Pro, and who has a connection with the network.  I downloaded the driver from HP on the laptop to try to connect with the 6940, but during the install process, I get the message "Printer not found - Setup could not detect all the printers on the network."

  Firewalls on both computers is disabled.

  When I type the IP address in the address of the host computer or on the portable bar, I page of the printer, including its SSID.

  I tried to type the IP address in the field suitable for the installation of HP on the portable routine, however and always got the "printer not found."

  Ideas?  TIA

  The Deskjet 6940 being on the network, we will try to add the printer manually. Here is the sequence to XP:

  1. Click on the button 'Start'--> Printers and fax machines.
  2. Under print jobs, click on "Add Printer".
  3. Click 'Next' in the Add Printer Wizard window.
  4. Select " printer local to this computer. Deselect "automatically detect and install my Plug and play printer." Click "next".
  5. Under Select a printer Port option, select "Create a new port" and choose "Standard TCP/IP Port" and click "Next".
  6. In the "Welcome to the Add Standard TCP/IP printer port Wizard" make sure that the printer is turned on and connected to the same network that your computer is connected to. click on the button "next".
  7. Under "Add Standard TCP/IP printer Port", enter the host name of the printer . You can also use the IP address of the printer if it is static. Click 'Next' and then click 'Finish '.
  8. Now, select HP in the manufacturers list, select your printer from the printer model list and click the button "next".
  9. If you can't find your printer, you will need to find the installation CD and use the 'Disc' option to select one of the files hp*.ini. You can also select another model of the same type HP printer.
  10. Add the name of print spooler and click on "next".
  11. Click "next".
  12. Click "Next" and "Finish."

• Create a disc of the Encyclopedia Britannica, which is designed for up to Windows XP with Vista work. Is this possible?

  Create a disc of the Encyclopedia Britannica, which is designed for up to Windows XP with Vista work. Is this possible?

  Hi Silas Martin,

  I have not used Britannica for many years now, but I suppose there is a program of "installation"? If so, try compatibility mode.

  1 / locate the setup.exe (or install file) for the program of Britannica

  2 / right click on the file setup.exe or install.exe, and in the drop-down menu, select Properties.

  3 / in the Properties window, click the Compatibility tab

  4 / on the Compatibility tab place a 'TICK' in the box beside the box "run this program in compatibility mode for", then select the operating system Windows XP (Service Pack 3). This should automatically appear in the box under the run this program in compatibility mode for option. If Windows XP is not visible, then click on the arrow down to see a selection of the available operating system options.

  5 / click OK

  6 / the installation program will now begin to install the program in compatibility mode for Windows XP

  7 / once done, you should be able to run the program as if you were using Windows XP

  This forum post is my own opinion and does not necessarily reflect the opinion or the opinion of Microsoft, its employees or other MVPS.

  John Barnett MVP: Windows XP Expert associated with: Windows Desktop Experience: Web:http://www.winuser.co.uk;  Web: http://xphelpandsupport.mvps.org;  Web: http://vistasupport.mvps.org;  Web: http://www.silversurfer-guide.com

• Tecra S3 - HDD was not detected during the intallation of win7

  Hello

  I have Tecra S3 PTS30E, serial No. is 17023153 H.

  Now installed windows xp, I want to install Win7, but the HARD drive is not detected during installation. Windows xp works with this HARD drive.

  Why this problem?

  Please help me on this problem.

  Hello

  Tecra S3 supports RAID. Therefore, you need to install the RAID driver
  When installing XP, you will need to press F6 to add the RAID driver.

  Here the driver I found on the page of the European driver Toshiba

  [Driver RAID Tecra S3 | http://eu.computers.toshiba-europe.com/innovation/download_driver_details.jsp?service=EU&selCategory = 8 & selFamily = 195 & selSeries = 335 & selProduct = 596 & STAS hortMod = 431 & language = 13 & selOS = 10 & selType = 262 & yearu pload = & monthupload = & dayupload = & useDate = null & mode = a llMachines & search = & action = search & macId = & country = al l & selectedLanguage = 13 & type = 262 & page = 1 & ID = 43966 & OSI D = 10 & driverLanguage = 42]

• Satellite M40-276 - memory not detected in the Bios upgrade

  Hi people!

  New kid on the block!

  I have a client with a toshiba Satellite m40-276. I've updated his memory to give it a little more to play with...

  Went into the bios to see if everything was OK but no projected additional memory. I removed the new and old memory and put in the new 1 GB module and restart the computer.
  The bios has not yet changed the size of the old memory?

  Went to windows and of course that the memory has been detected it normally?
  I added the other memory module and went into the bios again, but no change it?

  Windows, however, recognized that the two modules?

  His computer is the same bios to factory and has never been updated.

  My questions are... why the bios doesn't recognize the upgrade memory? It will help in upgrading the bios?

  Enjoy all the suggestions I can get on this issue.

  Thank you

  bookie56

  Generally, if you upgrade RAM using tested compatible modules, that should be recognized correctly.
  We do not know what modules you use, and I guess that there is a compatibility issue.

  RAM on Satellite M40 276 can scale up to 2 GB of RAM and compatible modules are:
  DDR2 400/533 256 MB (PA3389U - 1 M 25)
  512 MB DDR2-400/533 (PA3412U - 1 M 51)
  1 GB OF DDR2 400/533 (PA3411U-1M1G)

• IMac-formatted external hard drive is not detected in the window computer

  I had formatted my drive external hard seagate new with the imac. now the problem is that it is detected in the iMac and not in my computer window. kindly help me in the detection of seagate in my computer window

  What format do you have selected?

  Ciao.

• IPhone 6 is not detected by the Pc and itunes...

  I'm suffering from a strange problem, my iphone 6 is not detected by my laptop or even itunes, but its loading... I'm trying to connect to my old iphone 5 and 6 and its works very well...

  Could you please help me on what I can do with this phone, I already searched a lot and try every thing like restarting the laptop etc etc, but nothing works at all...

  Appreciated your kind reply...

  It may depend on your OS of the computer. What computer OS do you use? The latest version of iTunes works with some versions of OS X. either way, you can see this support document. If iTunes does not your iPad, iPhone or iPod - Apple Support