A battery of 6 cells of a T60 will work in a T500

Similar Questions

• battery of 6 cells S10 (celxpert LE60_c)

  So I bought one of these 3rd party cell batteries 6 and it works fine, except that the S10 think it is in the battery 6 cells is used.

  I guess that's not a big deal, but someone has encountered this problem and found a solution or problem?

  Running on the factory to install XP.

  It would be good to know if anyone is having this problem?

  Thank you

  T.

  Actually I figured out with the help of some of the other forums s10, if someone else has a problem with the S10 recognizing the new battery test this:

  1. stop the laptop
  2. remove the a/c (plug) adapter
  3. remove the battery
  4. press on the power button for 30 seconds
  5. wait approximately 30 seconds more
  6. put the battery back into the laptop
  7. turn on the laptop

  Now the laptop should recognize the new battery properly.

  I hope this helps others out.

  T.

• I can not install Lightroom 6 on my laptop using 8.1 to WIN.  The installer asks me to connect and when I do after 20 sec freezes the computer and the battery needs to restart.  This prevents the work online help.  What can I do?

  I can not install Lightroom 6 on my laptop using 8.1 to WIN.  The installer asks me to connect and when I do after 20 sec freezes the computer and the battery needs to restart.  This prevents the work online help.  What can I do?

  Settle in the right forum.

• Battery life 8 cells

  Hey I just got my hp dv7-1245, and I noticed that my battery goes down pretty quickly. What is the battery life on this type of battery?

  Based on what you say, if you get anywhere near 2 hours you do well.

• Automatic switching of WiFi in the cell for the data not work, requires a restart of the phone

  The phone is a peak of Geeksphone, and the version of the operating system is 1.4. The problem is with the automatic switching of the WiFi to cell for my data. If I take the phone outside the WiFi range, it does not acquire the data (2 G, Edge, H or 3 G) signal and so I have no data. I left for hours without success. The only solution is to reboot the phone, then outside the configured WiFi connections and it will collect data signal. When I re - get the WiFi area, it captures the network and without problems.

  I also had this problem with version 1.1. I upgraded to think it could be fixed, but he did not.

  Thank you, Ralph. There was an update available which appear not yesterday. After the installation, I get the options that you quote, namely to turn the cell data in the notification area. Thanks a lot for the tip and the quick response.

• Why a formula will work in each cell of each other than A column?

  Just for appearances, I would like to see the result of a formula in A4 format. When I enter the formula in A4, it returns an error. However, when I copy and paste the formula (or drag the cell) into any other cell in any column that does not have one, the function works perfectly.

  I recheck the formula after its entry into the cell in column A and all the characters in the formula are exactly the same as in any other cell in all other columns.

  Note: I have header columns and lines disabled for this table. I use version 3.6.2 of numbers.

  What is going on? I'm going nuts. How can I fix it?

  Thanks for any help.

  We really need to see the formula you are trying to use. sounds like your formula can refer to A column, which would create a circular reference. (as = Sum(A:A) who would try to summarize each number in A, but trying to sum column A4 has again and again...)

  If you can give us this information, we may be better able to help.

  Thank you

  Jason

• Satellite battery click on Mini L9W - B keyboard will not charge

  My keyboard battery will not charge, I left it loads for more than 24 hours after the battery 1 reached 100%.

  I checked the version of the bios that is 1.70. I read the other posts on this particular issue but unfortunately nothing works for me.

  It shows the symbol of charge on battery 2, but it did not go above 0%. If I turn on the battery runs immediately battery 1.

  Please advise me on this point because otherwise I will have to return my satellite click mini. Thanks in advance

  You completely turned the device off?

  Do... Press and hold the power button / stop until the device turns off.
  In addition, you can stop the unit pressing and holding the key SHIFT and then choose SHUT OFF

  Then check the connection between the keyboard and Tablet docker... possibly disconnect and connect again.
  Once the unit turns on again and check the battery State of charge connection adapter to the device.

• IPhone 6 s fast battery draining not certified charge cords have stop working

  6 IPhone began to deplete the battery fast and all cords load uncertified leave support, message from apple on these cords has appeared on the screen. Did nothing to call in a month. OS 9.2 operating. Phone of the wiped twice. With cloud backup, and then as a new device. No change. Same problems. Read a few threads on iCloud being the problem, but my phone was working fine since 9.2 update. On my third wipe with restoration of the cloud, SLOWLY MOVING! No problem on my mini4. I see that there is a new update, 9.2.1, no of course. First time I had confidence that apple will update... any suggestions?

  Hi Mycheezmo,

  Thank you for using communities Support from Apple. I'm sorry to hear that you are having these problems with your iPhone. If you encounter unusual battery drain issues, you can find the information and steps on the insulation of use described in the following articles useful:

  On the use of the battery on your iPhone, iPad and iPod touch - Apple Support

  Batteries - maximize Performance - Apple

  Concerning

• T60 will not start

  One day, I tried to start my lenovo T60 IBM and it came with a black screen and wouldn't boot in what either.

  EDIT: The screen is broken

• Laptop battery will work for many years if I run the laptop without it?

  Hello

  Model No. - HP Pavilion dv6330ea laptop. Check out the link http://h10025.www1.hp.com/ewfrf/wc/product?cc=us&dlc=en&lc=en&product=3411896&

  My operating system is Vista Home Premium 32-bit with Service Pack 2.

  I use my laptop more than 20 hours a day. I have connected my laptop to the power adapter that connected to the ups (uninterruptible power supply) and from there it connects to the wall jack. Given that I have turn my laptop so long, so I removed my battery and put aside. Because I thaught if I have my battery is connected with my laptop, then life battery will decrease since I use my laptop for more than 20 hours a day. That's why I took off. I'm using this method for a few years.

  I use my PC laptop battery only when I travel I make much less.

  So I was wandering if it is good practice to remove the battery and run the laptop for power adapter?

  My battery will be coming for many years or it will get cuttings due to not use it for a long time?

  What is your opinion, to run the laptop with the battery or not - computer since I use my laptop more than 20 hours a day?

  Please reply as soon as possible.

  Bye,.

  Siva

  Hi Siva,

  It is certainly very well run Notepad on just the AC adapter.

  Regarding the battery once a month, reinsert the battery, turn the machine on and let the battery fully charged.  Unplug the AC adapter and let the unit run until you start getting a "low battery" warning  Completely load it again, then let the battery drain to about 40%.  Shut down the laptop, remove the battery and store it separately in a cool place.  Repeat this procedure each month will help you keep your battery in good condition.

  For more information on lithium-ion batteries, see link below.

  http://BatteryUniversity.com/learn/article/is_lithium_ion_the_ideal_battery

  Kind regards

  DP - K

• T60 will not boot receive the beep code 1-3-4-3 any suggestions on what this might be?

  Hi guys,.

  My T60, does not start all of a sudden. I can't access the BIOS. I received the following beep sequence: 1-3-4-3.

  I looked around and got as a message for phoenix BIOS beep code 'Test 512 K base memory '. Anyone has an explanation, and I should do or change?

  Thanks a lot for your support!

  Antoine

  I don't have one of them, but if it's a mistake of memory, the best way to test is to substitute known good memory. If you have two SODIMM modules installed, remove them and install one at the time and the test.

  Sometimes remove and reset of memory are sufficient to solve the problem.

  If this does not help, a good 'generic' method that I use on all laptops with a no boot situation is to remove all the drives and cards, then see if it will boot to the BIOS, or post at all. I've seen poor readers force a system not to post, so remove everything that is not required will be an easy way to identify the cause. Usually, if it will not always display, you'll have a system board failure.

• My Celler mass storage device will not work on Windows 7

  I have a storage device mass of Celler that has always worked with several computers, now on Windows7 home premium 64-bit, that it says it can't find the drivers. I had Windows search for drivers, but the attempt failed. All solutions? It's most basic 2.0 mass storage device.

  Contact the manufacturer of the device on the drivers for it.

  The manufacturer has written drivers for their products, not Microsoft.

  http://www.Microsoft.com/Windows/compatibility/Windows-7/en-us/default.aspx

  Windows 7 Hardware/Software Compatibility Center.

  http://www.SevenForums.com/tutorials/316-compatibility-mode.html

  How to run a program in Compatibility Mode in Windows 7 is at the link above.

  For any question on Windows 7:

  http://social.answers.Microsoft.com/forums/en-us/category/Windows7

  Link above is Windows 7 Forums.

  There is a list of the Windows 7 Forums at the link above to help you.

  You get the help you need there.

  You are in the Vista Forums.

  See you soon.

  Mick Murphy - Microsoft partner

• T60 will not pick up a valid ip address, driver seems ok, works fine without thread

  Hi I have a T60.

  In network device manager driver is showing that "Intel (r) PRO/1000 PL Network connection.

  but I can't get the machine to retrieve an IP address.

  I checked the network ports and they all check out ok, that is to say that they are certainly direct and giving valid ip addresses.

  I can't understand why its not working properly.

  has any one come across this before?

  I uninstalled and reinstalled the network device, but its still does not.

  Thank you

  Damien

  Hi Damien. I have a few questions for you here:

  (1) when you connect the ethernet cable, you see both the Green and orange lights flashing? If all goes well it is not a problem with the internal pins on your NETWORK card or a problem with the configuration of the router or the cable itself.

  (2) in addition, go to the shell (start-> Run-> CMD-> Enter) prompt and type the following for me:

  Ping 127.0.0.1

  Let me know if you see 4 answers with 0% loss

  Then, type the following at the shell prompt:

  ipconfig

  Type the shown static results. Need to see the IP address, subnet mask and gateway showing.

  I check to see if there are problems of configuration first. You can of course also use the release and renew orders and empty the DNS if necessary. Winsock reset possible too help?

  If everything looks normal and the problem persists, you want to consider getting the motherboard replaced. Systembords can act funny at times (especially with the integrated NETWORK card). This should solve the problem, Yes... but just do some it do not configure the questions first.

  Let me know if that helps you at all.

  Best,

  Mark

• Remove a switch in the stack and put on another battery, it will work

  Hello!
  I have two different batteries, in two different place

  Location01
  STack01-> with dial-up dell PC8164-01 and 02-PC8164

  Location02
  STack02-> with dell switched PC8164-03 and 04-PC8164

  On all switches, I use the same ports for stacking

  Now, assume that this scenario:
  If the switch PC8164-02, which is a member of stack01 located in Location01 is damaged and I remove switch 04-PC8164 of location02 and connect to location01, it will be normally function and configuration of the reception of the other switch in battery PC8164-01, and he will be a Member?

  Kind regards!

  Yes, the switch will operate normally. When the switch is connected to the other battery it will see that there is already a main switch, since it has only 2 switches, it will become the cutout of backup, synchronization configuration and become an active member of the stack.

  You will need to ensure that all switches are on the same firmware.

• T60 will not identify new 2 GB Dimm

  Just a quick question to the community: my thinkpad T60 comes with a module of 512 MB Dimm and I installed a new 2 GB Dimm (alongside the original 512 MB).  The "thinkvantage" information system says I have 1022 mb of installed memory.  Information system control panel windows says I have 2.5 GB.  I downloaded the fancy of the Lenovo Web site utility to tell me what is in each Dimm slot and it says: no support for memory, for the two slots.

  Any ideas on what is happening here?  I tried the DIMMs of switching between the two slots, which seemed to have no effect.  Also tried to Flash the bios, which had no effect.  Moreover, memory is the part number, genuine Lenovo correct (whatever it is worth).

  Thanks a bunch!

  Looks like your laptop is fine, just the ThinkVantage System Info cannot recgonize the memory.  Maybe a ThinkVantage System Info Update will solve your problem.

  The Bios reports 2.5 GB of ram?

  André