A new facility to clean impossible Yosemite (France)

Similar Questions

• MacBook pro 2009 with new SSD try to clean install Yosemite or TM disaster restoration.

  Hello.

  I think this is going to be a difficult discussion.

  Unibody MacBook Pro 2009. Original Apple HDD with Yosemite 10.10.5.

  Two months ago, that my HARD disk is dead.

  I installed a new SATA II Toshiba 1 TB HARD drive and through the recovery of TM all went well.

  A couple of weeks, my 'new' SATA II Toshiba 1 TB HDD started to scratch a little (I mean literally zero while reading/writing), so I thought he would die soon again. This time, I decided to buy an SSD in order to have better performance and superior durability.

  So I bought a Toshiba 248 Gb SSD. I'm not a big fan of Toshiba, but where I live, it's the SSD only I found in the store.

  I removed the old HDD, I installed the new SSD and where my nightmare starts.

  First of all, I tried with a new Installation of USB from Yosemite. I followed all the passages and the installation completed in about 9 days. Yes you read that right: 9 days. The progress bar runs for 9 DAYS.

  At the beginning I obviously interrupted the first couple of facilities when the progress bar was like "12 minutes at the end" for three or four hours, but then I read in many articles and support threads that it is quite usual installation seeks stuck for hours or days, but if you open the log console computer is always something. So I gave him his time and the third or the fourth installation I waited my NINE DAYS to be finished.

  Then when the installation ended the restarted mac of himself and is stuck at the loading screen with his beautiful Apple and the progress bar frozen at about 50%.

  I froze for about 4 or 5 hours of average.

  I found a few articles that sometimes happens, and all you have to do is to force the computer to shut down and start again. So I tried to force the shutdown by holding down the power button and after the reboot it just keeps starting with and stuck at first infinite progress bar.

  So I reboot on CMD + R to get a clue, if I got in trouble on the SSD or what. I run disk utility and found that on my SSD were about 290,000 files and many files as the Yosemite was finally installed. I tried to check the permissions, but it says less than a minute and then got stuck at halfway to complete 15 minutes, so I stopped it.

  After that I think 4 or 5 attempts to start new fresh install on my Yosemite and clean, I reset the SSD erase decided to start all over again.

  I died a little inside while doing it. Same as the erasure was so f * king quick to finish! (about 50 seconds, sonofa 'byte').

  Then I tried to not reinstall Yosemite again (the nightmare of 9 DAYS still has me) but I have tried a new way: recovery of TM.

  Just to say my original TM backup was about 340 GB and my new SSD is 248 only while it was quite clear he wasn't.

  I connect my external TM drive to another computer and I worked the ' delete all backups of * file * ' to get a smaller backup TM.

  Now, I moved a lot of things outside the TM backup and the new dimension of the TM backup is about 90 GB (I want to say that the whole folder backups.backup is about 90 GB), in fact I moved the other stuff was also inside the external Western Digital drive and is now free space Go 910 (, hence the content of the WD is just the TM backup folder this weight about 90 GB), but I still have the 'this drive doesn't have enough space to restore your system.', it's totally A LIE.

  Never mind. I accepted the idea that sometimes even computers are ashamed of themselves and begin to tell lies. I can handle. There was a holy man in the history without any sin. So, ok, no problem. I'm not upset or anything. I can get over it (mf you little liar!).

  Think of manually restore the files that I needed once I have a BONE in my new SSD, I used the same external disk to create a new backup from another computer, my Mac Mini TM. Everything went well and I got a new Mac Mini TM backup about 60 GB (it's much less than 248 GB of my new SSD).

  I reboot the Macbook again to try to restore the backup, Time Machine of Mac Mini and everything seems to work, except for:

  -progress initially said about 650 hours needed to complete the restoration ago.

  -I went to sleep and let the machine itself working together on the restoration and when I woke up this morning I found that the rest of the time was "fair" 52 hours.

  -J' was a little happy to see this, until the Rainbow rolling ball appears. Everything got stuck again. I force shutdown and then try to restore it.

  Now it works again and the remaining time is close hours 672 (and growing). I'll give it another chance. We'll see.

  Now, I have four questions to ask you:

  1. you have an idea (with the exception of a curse or a matter of black magic) WHY all this happened? And of course if there is something wrong and I can work to fix it otherwise?

  2 are there special settings to enable/disable/configuration/whatever to create works faster still to understand that it doesn't properly before discovering this NINE DAYS or 672 HOURS right now?

  3. when we agreed that something like that was acceptable? I used to be a project leader in the world of ICT and in 20 years I NEVER, I say NEVER, released a product/app/site Internet/solution that considers that an option taken 9 DAYS to install or something like that. NEVER. Do not forget that we are talking about Apple and an operating system. I think Windows is laughingly taking revenge.

  4. do you think that for me it is time to let Apple and go back WIN + PC? It's quite frustrating and I use the computer to WORK, not to play games video and this is not the kind of operativity expect after paying a little more for material, a little more for software, a little more to be part of what it is supposed to be the one that had the best choice (index not be not it kills me).

  I thank in advance for any help/tip, you can provide.

  Alberto

  This is a fairly long post. What I would say is:

  1. the next time get a hard drive from a company with a good reputation like Samsung (best SSD ever, I have several internal parts and a laptop EVO). I get them shipped.

  2. as you use the Mini, the recovery partition allows you to install a new copy of Mac OS X, and then use the Migration Wizard to move your stuff.

• I had a copy of Windows 7 Ultimate SP1 for quite awhile and discovered that I need a new facility (the computer refuses to Windows to run at all).

  Hello!

  I had a copy of Windows 7 Ultimate SP1 for quite awhile and discovered that I need a new facility (the computer refuses to Windows to run at all). I picked up my installation disc and everything, only to find out that someone stole completely he reapply. I am unsure weather or not it is enabled or whatever it is. I tried to call Microsoft technical support and they said to go to the retailer I bought since then, but the retailer in question no longer exists. I'm just screwed?

  Thanks for your help!

  You can retrieve the product key, and then use it to re-download a new copy:

  Here are four utilities, which can display your product keys if they are still there:
  Belarc Advisor: http://www.belarc.com/free_download.html
  (He did a good job of providing a wealth of information.)

  Also: http://www.magicaljellybean.com/keyfinder.shtml
  and: http://www.nirsoft.net/utils/product_cd_key_viewer.html
  and RockXP: http://www.majorgeeks.com/download4138.html which has additional features

  Go to the recovery of the software Page and then enter your key:

  How to: What are my options for Windows 7 reinstall media?

  Make sure you scroll down and read the section:

  What to do if you cannot get your manufacturer recovery media, refuse to use or to buy it or the Microsoft Software Recovery Website does not work?

  If you plan to upgrade to Windows 7, see:

  Task of pre-required

  When you make significant changes to your computer for example updated operating system, you must always back up. See the links to resources on the backup by clicking the link for each version of Windows you are using: Windows XP, Windows Vista, Windows 7, Windows 8/8.1

  • How to back up and restore your files manually
  • How to free up disk space in Windows
  • How to: 10 tips before installing Windows 10
  • How to: determine if a device application or hardware is compatible with Windows 10
  • Will remain the documents and applications, or install app must

  then

  • How to download official Windows 10 ISO files
  • How to: upgrade previous versions of Windows using the file ISO for Windows 10

  then

  • Turn off (preferably uninstall) your Antivirus utility before you perform the upgrade.
  • Reboot several times, and then try again.
  • Disable the general USB peripherals (for example - smart card reader).
  • If you are using a SCSI drive, make sure you have the drivers available for your storage on a thumdrive device and it is connected. During the installation of Windows 10, click on the advanced custom Option and use the command load driver to load the driver for the SCSI drive. If this does not work and the installer still fails, consider switching to an IDE based hard drive.
  • Perform a clean boot, restart, and then try again.
  • If you upgrade to the. ISO file, disconnect from the Internet during the installation, if you are connected in LAN (Ethernet) or wireless, disable both, then try to install.
  • If you are updated through Windows Update, when download reaches 100% disconnect from the LAN (Ethernet) Internet or Wi - Fi, then proceed with the installation.
  • If this does not work, try using the. ISO file to upgrade if possible.
  • If you are connected to a domain, go to a local account.
  • If you have an external equipment, attached to the machine, unplug them (example, game controllers, USB sticks, external hard drive, printers, peripherals not essential).

• "Adobe Creative Cloud is necessary to solve this problem. However, it is missing or damaged. Please download and install a new copy of the creative cloud "."    Then on the new facility to download. the process stops and repeats this message...

  I get the error message ' Adobe Creative Cloud is necessary to solve this problem. However, it is missing or damaged. Please download and install a new copy of the creative cloud '.    Then on the new facility to download. the process stops and repeats this message...

  

  Hi Jory,

  Run the first CC cleaning tool to remove Adobe Creative cloud completely from your machine.

  Use the CC cleaning tool to resolve installation problems. CC, CS3 - CS6

  Once it is completely removed, you can download the installer from the help below document:

  https://helpx.Adobe.com/creative-cloud/help/creative-cloud-desktop.html

  Kind regards

  Sheena

• Can I transfer my old regsitry to a new installation of clean boot of windows 7

  Can I transfer my old register to a new installation of clean boot of windows 7?  If so, how this is done?  Without a transfer, it is necessary to reinstall all my software and it is very time consuming.

  You will not be able to transfer all the registry settings. Unfortunately, you will need to reinstall everything.

• Windows 7 64 bit, new facility - choppy video playback

  I have a quad core Intel I7 HP laptop with 8 GB of RAM, 160 GB of free disk space. ATI Radeon 5600HD graphics card, the latest video drivers ATI, all updates for HP laptop, including the BIOS. The machine should be able to play videos and do a Skype video chat. But in both cases, the video is choppy and not really usable.

  I've been to all updates installed, SP1 for Windows 7, the software I use, etc, etc, etc, so I can't go back to previous restore points, at least that would make a difference.

  I just watched a WMV video that I downloaded (not heard), Channel 9, and it was awful to watch. The video stops but the sound would continue, finally all caught up. But then it would start all over again.

  Video of Skype is similar, the video stops but the sound continues.

  Given that I have the latest video drivers from ATI, and everything else comes from a new facility from 2 days ago. I'd appreciate any help to solve this problem.

  Thank you

  All companies (Dell, HP, Acer, Toshiba etc.) put things on their systems.

  Most of them pre-install programs such as Mcafee or Symantec / Norton. Both are hopeless and cause probs

  And most likely have some sort of trial version. What is the point of having this. It runs

  This is one of the reasons why I build my own desktop computers. I can put what I want on this subject, NOT what they think I need.

  No wonder so many of them have probs. It's the stuff they install on it.

• I've just updated my LR, but still can not read the new RAW files of my brand new Sony a6300. said 'impossible to read these files' is Adobe should update it program with new firmware to manage these new folders? Or something escapes me?

  I've just updated my LR, but still can not read the new RAW files of my brand new Sony a6300. said 'impossible to read these files' is Adobe should update it program with new firmware to manage these new folders? Or something escapes me?

  You updated Lightroom to version 6.5? This is the version you need. What is the exact wording of the message you receive?

• I allowed to CS2, I contact Adobe support for new link and new key for the new facility for the computer updated. In the installation, I have inserted the key from ADobe that I got Adobe support, but when I open programms CS2 it will not work and gives me

  I allowed to CS2, I contact Adobe support for new link and new key for the new facility for the computer updated. In the installation, I have inserted the key from ADobe that I got Adobe support, but when I opened any CS2 program it will not work and gives me the invalid key error. What should do?

  CS2: Error: unavailable activation server | CS2, Acrobat 7, hearing 3 -.

  l http://helpx.adobe.com/x-productkb/Policy-Pricing/Creative-Suite-2-activation-end-Life.htm

  https://helpx.Adobe.com/Creative-Suite/KB/CS2-product-downloads.html

• VSAN showing license key have expired on a brand-new facility.

  Currently have a test laboratory of the three hosts Vsphere implemented.

  With each host with a brand new facility, from magnetic today ESXi 5.5 and at least an SSD and one of the hard drives.

  I was able to initially configure the vsan through the command line on the first host, and then once I had imported the latest version of the standalone version of VCenter and added the two remaining hosts on the VCenter server. It would allow me to add additional disks to the cluster vsan because of a vsan expired license key error. I found this rather curious because everything is the oldest in its facility in four hours.

  If you help me to find a way to get the vsan on trial license once again, would be great.

  After having play with VCenter apparatus and ESXi hosts, looks like it was a problem syncing after all. Not so much the time set in the BIOS, as well the ignition when the VCenter unit is initially configured.

• Insert the Vision demo database in the new facility

  Hi gurus!
  
  I recently did a new install of EBS 12.1.1 in my linux. But I want to have a database of demonstration Vision (SCREW). Where can I download the data creation for the demonstration of Vision database? ...
  
  Thank you!!
  
  Pablo. -.

  PabloArroyo wrote:
  Yes I know, but I have a fresh install now. You tell me that if I run the rapidwiz now and I chose 'Vision démo Database' this would replace the new facility and will be doing an installation "Vision demo Database?

  Thank you very much!!

  Pablo. -.

  No, you must do the installation (new instance) again and choose to install the demo of vision database.

  If you do not use the fresh database that you have already installed, you must remove it and then again to install the demo of vision.

  Thank you
  Hussein

• How to make a "new facility" of Mac OS x

  I'm always under Yosemite 10.10.5 on my iMac 21.5 "because I met a complete disaster after my first attempt to ElCapitan November last year and restored Yosemite with the help of my TimeCapsule. (you can refer to my support community question "can Apps interfere with Keychain" November 5, 2015, if you're curious about what happened.) It's still not answered!)

  Since there is still some remaining problems since that mishap, I want to do a full OSX reinstall when I ultimately ElCapitan, I don't want to do just an upgrade.

  I read in the help files how to do this and got really scared! Help files seems to indicate that I need to recover files after a "new installation" as the process includes the total slate of HD!

  It's impossible! I have about 100,000 points on the disc!

  There must be a smooth way to have a gentle ElCapitan OSX installed have all my files on the HDD as before, but how?

  Back up your data, erase or repartitioning the internal drive, install El Capitan on the volume of the vacuum and then migrate your data from the backup when you install the new system.

  (138750)

• Updated Windows 8 do not install on restored factory new facility.

  I recently factory to restore a computer, which was installed with Windows 8. I tried repeatedly, apply updates Windows 8 to be able to install Windows 8.1

  What baffles me, is how installs it fail on a computer 'brand new '. It is without anything installed after the factory restore. Whenever I try to apply the updates, I get the message "failed Windows Setup updates. Restoration of the changes. Do not turn off your computer. »

  I tried to install updates by using the boot option, ran the update problems (claims the problems have been fixed), with and without the (Norton) antivirus running, tried sfc/scannow (no problem), chkdsk /r (no problem), memory (memory tested fine) test, drivers updated, deleted the software AMD catalyst without success.

  All by performing the updates, only the mouse and software (wire, wireless not) are connected to the computer. I tried all the possible solutions I found in the forums to find a solution. I don't understand how a facility, which is supposed to be direct from the factory, can not install updates. Is it possible to apply all updates, such as service packs earlier, or install Windows 8.1 without having first apply updates?

  If it helps, it's a HP Pavilion 20, with a processor AMD E1-1200, 4 GB RAM, 64-bit Windows 8.

  I recently factory to restore a computer, which was installed with Windows 8. I tried repeatedly, apply updates Windows 8 to be able to install Windows 8.1

  What baffles me, is how installs it fail on a computer 'brand new '. It is without anything installed after the factory restore. Whenever I try to apply the updates, I get the message "failed Windows Setup updates. Restoration of the changes. Do not turn off your computer. »

  The problem is the 8.1 Windows deployment by the Windows store is just buggy, leading to problems during installation and reduced performance. Also, you are using an HP printer, and therefore its probable that the original image has a lot of bloatware pre-installed which does not help. The particular system you have purchased must have also taken some time to sell because most of the systems were sold with Windows 8.1 opposed to 8 for some time.

  You are advised to clean the Windows 8.1 with 1 update installation directly, ignoring all the hassle of upgrading to Windows 8.1 via the Microsoft Store. To prepare a Windows 8.1 with 1 FAT32 USB Bootable update a UEFI BIOS and GPT partition scheme, see here:

  http://dellwindowsreinstallationguide.com/download-Microsoft-Windows-and-Office/Download-Microsoft-Windows/download-Windows-8-1-retail-and-OEM-ISO/

• After a clean install, Yosemite Mail crashes at launch

  I have re-installed Yosemite and upgrade 10.10.5 three days ago. Yesterday, I recreated 11 non-iCloud email accounts. I launched Mail and proceeded to uncheck the option "automatically detect and maintain the parameters" and to replace the port numbers incoming and outgoing according to the instructions of the ISP, I consulted in order to avoid the main Contacts and issues of mail in the course of the two months since my original Yosemite clean install - issues that have worsened to the point where I was advised in these forums to re - install. If I had known everything uncheck this option, perhaps none of these problems would be developed?

  After unchecking the option and change the port numbers for the incoming server and outgoing 11 IMAP accounts, I took all online accounts. Mail seems to be stable. I quit Mail and relaunched it five minutes later, just to be sure. He froze immediately on launch; There is not enough time to click on anything before spinning beachball appears and never goes away. I checked the Sys Prefs/Internet accounts: no problem.

  Here are the logs from Console for today attempted launch of Mail:

  06/07/2016 6:24:16.318 PM Mail [1318]: AllSignatures.plist: read plist error: error Domain = NSCocoaErrorDomain Code = 260 "the file 'AllSignatures.plist' could not be opened because there is no file of this type." UserInfo = 0x60800066c640 {NSFilePath=/Users/mother/Library/Mail/V2/MailData/Signatures/AllSignatures.pli st, NSUnderlyingError = 0x608000650ce0 "the operation could not be completed. No such file or directory"}

  06/07/2016 com.apple.xpc.launchd [1 6:24:16.379 PM]: (com.apple.imfoundation.IMRemoteURLConnectionAgent) the _DirtyJetsamMemoryLimit key is not available on this platform.

  06/07/2016 com.apple.xpc.launchd [1 6:24:17.853 PM]: (com.apple.imfoundation.IMRemoteURLConnectionAgent) the _DirtyJetsamMemoryLimit key is not available on this platform.

  06/07/2016 6:24:18.409 PM Mail [1318]: dnssd_clientstub DNSServiceProcessResult called with DNSServiceRef without ProcessReply function

  06/07/2016 6:24:18.409 PM Mail [1318]: dnssd_clientstub DNSServiceProcessResult called with DNSServiceRef without ProcessReply function

  06/07/2016 6:24:18.410 PM Mail [1318]: dnssd_clientstub DNSServiceProcessResult called with DNSServiceRef without ProcessReply function

  06/07/2016 6:24:18.410 PM Mail [1318]: dnssd_clientstub DNSServiceProcessResult called with DNSServiceRef without ProcessReply function

  06/07/2016 6:24:18.410 PM Mail [1318]: dnssd_clientstub DNSServiceProcessResult called with DNSServiceRef without ProcessReply function

  06/07/2016 6:24:18.410 PM Mail [1318]: dnssd_clientstub DNSServiceProcessResult called with DNSServiceRef without ProcessReply function

  06/07/2016 6:24:18.410 PM Mail [1318]: dnssd_clientstub DNSServiceProcessResult called with DNSServiceRef without ProcessReply function

  06/07/2016 6:24:18.410 PM Mail [1318]: dnssd_clientstub DNSServiceProcessResult called with DNSServiceRef without ProcessReply function

  06/07/2016 6:24:18.477 PM Mail [1318]: dnssd_clientstub DNSServiceProcessResult called with DNSServiceRef without ProcessReply function

  06/07/2016 6:24:18.477 PM Mail [1318]: dnssd_clientstub DNSServiceProcessResult called with DNSServiceRef without ProcessReply function

  06/07/2016 6:24:19.059 PM Mail [1318]: [IMAP] should untagged first response box495.bluehost.com

  06/07/2016 6:24:19.146 PM Mail [1318]: [IMAP] should untagged first response box495.bluehost.com

  06/07/2016 6:24:19.532 PM accountsd [336]: cannot find executable for CFBundle < /System/Library/Accounts/Notification/CloudDocsAccountNotificationPlugin.bundl e > 0x7fc1e9d159f0 (unloaded)

  06/07/2016 6:24:19.756 PM fontd [296]: BUG in client libdispatch: dispatch_mig_server: mach_msg() has memory invalid (ipc/send) - 0x1000000c

  06/07/2016 6:24:19.756 PM Mail [1318]: CoreText CopyFontsForRequest received mig CPI error (FFFFFFFFFFFFFECC) font server

  06/07/2016 6:24:19.756 PM Mail [1318]: CoreText CopyFontsForRequest received mig CPI error (FFFFFFFFFFFFFECC) font server

  06/07/2016 6:24:20.351 PM accountsd [336]: enter ShareKitAccountEnabler - didChangeWithType - type = 2 for the [email protected] (843792E4-0915-4FE8-BD0F-D1018E23DF1F) account.

  06/07/2016 6:24:20.372 PM accountsd [336]: AIDA Notification plugin running

  06/07/2016 com.apple.xpc.launchd [1 6:24:20.404 PM]: (com.apple.imfoundation.IMRemoteURLConnectionAgent) the _DirtyJetsamMemoryLimit key is not available on this platform.

  06/07/2016 6:24:20.592 PM icbaccountsd [1326]: error in connection verifying Apple Internalness. Error: Domain = NSCocoaErrorDomain Code 4099 = "could not connect with a helper." (The connection to the service named com.apple.CrashReporterSupportHelper has been invalidated.) UserInfo = 0x7f9e40e0a160 {NSDebugDescription = the connection to the service named com.apple.CrashReporterSupportHelper has been invalidated.}

  06/07/2016 6:24:20.630 PM sandboxd [393]: ([1326]) icbaccountsd (1326) deny com.apple.CrashReporterSupportHelper mach-search

  06/07/2016 6:24:22.825 PM Mail [1318]: [IMAP] should untagged first response box495.bluehost.com

  06/07/2016 6:24:22.920 PM Mail [1318]: [IMAP] should untagged first response box495.bluehost.com

  06/07/2016 6:24:25.409 PM Mail [1318]: [IMAP] should untagged first response box495.bluehost.com

  06/07/2016 6:24:25.503 PM Mail [1318]: [IMAP] should untagged first response box495.bluehost.com

  06/07/2016 com.apple.xpc.launchd [1 6:30:09.116 PM]: (com.apple.mail.3156 [1318]) Service was released due to the signal: completed: 15

  06/07/2016 6:30:12.835 PM spindump [533]: report of hang Saved mail version 8.2 (2104) at /Library/Logs/DiagnosticReports/Mail_2016-07-06-183012_MacBookPro.hang

  06/07/2016 6:31:29.425 PM Console [1336]: unable to connect (_consoleX) out of (NSApplication) (ConsoleX): missing setter or instance variable

  If the problem is still there, try to start safe mode using your usual account.  Disconnect all devices except those necessary for the test. Shut down the computer and then put it up after a 10 second wait. Immediately after hearing the startup chime, hold down the SHIFT key and continue to hold it until the gray Apple icon and a progress bar appear. Startup is considerably slower than normal. This will reset some caches, forces a check for directory and disables all start-up and connection, among other things. When you restart normally, the initial restart may be slower than normal. If the system is operating normally, there may be 3rd party applications that pose a problem. Try to delete/disable the third-party applications after a reboot using the UN-Installer. For each disable/remove, you need to restart if you do them all at once.

  Safe mode - subject

  Safe mode - Yosemite

• Windows Update crashed my laptop and after a new facility could not activate

  Hi after a windows update crashed my pc I did a clean install and tried to activate once again (the first installation was adopted by w.g.a and I got the essentials pack to) no joy forced then to a person who says my product key is a license key for volume and then blocked it forwarded to someone else , they said it wasn't, but wanted more money to send me a disk and Reports I have found the old windows still on my laptop when I drive cleanup to my prob is that nobody knows what they cannot cross to anyone talking to e-mail, or anything they don't understand me very well and visa versa I ran the diagnostic tool as seen in a previous post on the forum so I copy it here as you will see it is retail and spirits half microsoft cannot see this please I need help from someone that I will not part with a penny more Diagnostic (1.9.0027.0) report:

  -----------------------------------------

  Validation of Windows data-->

  Validation code: 0

  Validation caching Code online: n/a, hr = 0xc004f012

  Windows product key: *-* - 9DMXM - D9PYG-V37W4

  Windows product key hash: Q3WGqGGPEN7oeBvTdMNbohEHKBU =

  Windows product ID: 00426-067-8684484-86608

  Windows product ID type: 5

  Windows license type: retail

  The Windows OS version: 6.1.7600.2.00010100.0.0.001

  ID: {85D6A796-6393-492C-91F8-1C9E28A5553C} (1)

  Admin: Yes

  TestCab: 0x0

  LegitcheckControl ActiveX: N/a, hr = 0 x 80070002

  Signed by: n/a, hr = 0 x 80070002

  Product name: Windows 7 Ultimate

  Architecture: 0 x 00000009

  Build lab: 7600.win7_gdr.100618 - 1621

  TTS error:

  Validation of diagnosis:

  Resolution state: n/a

  Given Vista WgaER-->

  ThreatID (s): n/a, hr = 0 x 80070002

  Version: N/a, hr = 0 x 80070002

  Windows XP Notifications data-->

  Cached result: n/a, hr = 0 x 80070002

  File: No.

  Version: N/a, hr = 0 x 80070002

  WgaTray.exe signed by: n/a, hr = 0 x 80070002

  WgaLogon.dll signed by: n/a, hr = 0 x 80070002

  OGA Notifications data-->

  Cached result: n/a, hr = 0 x 80070002

  Version: N/a, hr = 0 x 80070002

  OGAExec.exe signed by: n/a, hr = 0 x 80070002

  OGAAddin.dll signed by: n/a, hr = 0 x 80070002

  OGA data-->

  Office status: 109 n/a

  OGA Version: N/a, 0 x 80070002

  Signed by: n/a, hr = 0 x 80070002

  Office Diagnostics: 025D1FF3-364-80041010_025D1FF3-229-80041010_025D1FF3-230-1_025D1FF3-517-80040154_025D1FF3-237-80040154_025D1FF3-238-2_025D1FF3-244-80070002_025D1FF3-258-3

  Data browser-->

  Proxy settings: N/A

  User Agent: Mozilla/4.0 (compatible; MSIE 8.0; Win32)

  Default browser: C:\Users\bigworm\AppData\Local\Google\Chrome\Application\chrome.exe

  Download signed ActiveX controls: fast

  Download unsigned ActiveX controls: disabled

  Run ActiveX controls and plug-ins: allowed

  Initialize and script ActiveX controls not marked as safe: disabled

  Allow the Internet Explorer Webbrowser control scripts: disabled

  Active scripting: allowed

  Recognized ActiveX controls safe for scripting: allowed

  Analysis of file data-->

  Other data-->

  Office details: {85D6A796-6393-492C-91F8-1C9E28A5553C}1.9.0027.06.1.7600.2.00010100.0.0.001x 64*-*-*-*-V37W400426-067-8684484-866085S-1-5-21-1530103319-2218184202-3224238718Sony CorporationVGN AR71MPhoenix Technologies LTD.R2090J820080226000000.000000 + 000D2B93607018400F808090409GMT Standard Time(GMT+00:00)03SonyVAIO109

  Content Spsys.log: 0 x 80070002

  License data-->

  The software licensing service version: 6.1.7600.16385

  Name: Windows 7 Ultimate edition

  Description: operating system Windows - Windows (r) 7, retail channel

  Activation ID: a0cde89c-3304-4157-b61c-c8ad785d1fad

  ID of the application: 55c92734-d682-4d71-983e-d6ec3f16059f

  Extended PID: 00426-00172-067-868448-00-2057-7600.0000-0072011

  Installation ID: 003762179656672381174892533605042623272672513292480572

  Processor certificate URL: http://go.microsoft.com/fwlink/?LinkID=88338

  The machine certificate URL: http://go.microsoft.com/fwlink/?LinkID=88339

  Use license URL: http://go.microsoft.com/fwlink/?LinkID=88341

  Product key certificate URL: http://go.microsoft.com/fwlink/?LinkID=88340

  Partial product key: V37W4

  License status: initial grace period

  Time remaining: 23280 minute (s) on (16 day (s))

  Remaining Windows rearm count: 3

  Trust time: 01/07/2011-17:46:49

  Windows Activation Technologies-->

  HrOffline: 0x00000000

  HrOnline: n/a

  Beyond: 0 x 0000000000000000

  Event time stamp: n/a

  ActiveX: Registered, Version: 7.1.7600.16395

  The admin service: recorded, Version: 7.1.7600.16395

  Output beyond bitmask:

  --> HWID data

  Current Hash HWID: NAAAAAEABAABAAEAAAACAAAAAgABAAEA6GHSwxKGBgzW5NrrRoOuhRwT8mE4VZZwihZGyg ==

  Activation 1.0 data OEM-->

  N/A

  Activation 2.0 data OEM-->

  BIOS valid for OA 2.0: Yes

  Windows marker version: 0x0

  OEMID and OEMTableID consistent: Yes

  BIOS information:

  ACPI Table name OEMID value ValueOEMTableID

  SonyVAIO APIC

  FACP SonyVAIO

  HPET SonyVAIO

  START SonyVAIO

  MCFG SonyVAIO

  SLIC SonyVAIO

  Document TMOR SonyVAIO

  SonyVAIO APIC

  SSDT SonyVAIO

  SSDT SonyVAIO

  SSDT SonyVAIO

  SSDT SonyVAIO

  "Bear PA MS MVP" wrote in message News: 289 d 6602-862c-432c-9284-a5281f0a59f4...

  Right Church wrong Pew.

  Start a new thread in the following Microsoft Genuine Advantage forum and paste the results of the diagnosis of MGA tool in your post, and a clear description of your problem:

  http://social.Microsoft.com/forums/en-us/genuinewindows7/threads

  Troubleshooting specialist will analyze the data and recommend an appropriate solution.

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

  :)
  FWIW, applies the following...
  Windows product ID: 00426 -067- 8684484-86608 - MSDN key
   
  http://social.Microsoft.com/forums/en-us/genuinewindows7/thread/a2444f34-0AFF-4f29-a8ac-67e28b0c0285
   
  http://social.Microsoft.com/forums/en-us/genuinewindows7/thread/06698c46-8668-4ccd-A544-a88969265a6b
   
   
  
  --

  Noel Paton | Nil Carborundum Illegitemi | CrashFixPC | The lazy three fingers

• Upgrade Windows Vista Home Premium for Windos Pro 8 on HP laptop by way of a new facility.

  I tried upgrading to Windows 8 but experienced a problem and Windows Vista has been re-installed automatically. Now, I intend to do an install clean and bought a new disc of hard for it. Then I discovered that the previous version of Windows must be running on the PC before you can perform an upgrade to Windows 8. Suggestions how to go? Thank you.

  The link listed here is a web site of Dell but the download ISO (after burning a bootable DVD)
  works on any PC if you have a valid product key.

  ISO Vista: http://en.community.dell.com/support-forums/software-os/w/microsoft_os/3317.2-3-microsoft-windows-vista-official-iso-download-links-digital-river.aspx

  32-bit ISO: http://www.heidoc.net/joomla/technology-science/microsoft/57-windows-vista-direct-download-links

  After you download the .iso file using ImgBurn or gear to create a DVD ISO bootable.

  ImgBurn - in addition to supporting the creation of CD/DVD of. ISO files,
  It supports a wide range of image file formats, and it's free.
  (BIN, CUE, DI, DVD, GI, IMG, MDS, NRG, PDI and ISO)
  http://www.ImgBurn.com/

  Projectiles help you to use ImgBurn to screen: http://www.imgburn.com/index.php?act=screenshots
  Burn the ISO Images with ImgBurn article: http://neosmart.net/wiki/display/G/Burning+ISO+Images+with+ImgBurn
  (The steps are the same, except that you do not create a repair disk but complete an installation DVD)

  Note: Always use high quality DVD + R media and slower burning (4 x or 6 x) speed is offered a choice.

  After installing Vista activate using your Vista product key and then run the upgrad Windows 8.

  J W Stuart: http://www.pagestart.com