A VPN client can go same interface on the Pix 515

Similar Questions

• VPN client can get the gateway?

  I have a question for a long time.

  Cisco vpn client will find a gateway to the remote vpn server address.

  There are many situations in which we need a gateway assigned to the vpn client. If the customer can freely access all private networks.

  PIX of Cisco router has this feature?

  Why the customer would need a bridge tunnel?

  The customer already has a gateway of the ISP.

  Once the tunnel is up, if not to do split tunneling, all customer traffic will be sent on to the CONCENTRATOR's IPSec tunnel. So, indeed, the HUB is the default gateway.

  If you use the split tunneling, then your ACL will say what customer traffic must be encrypted on the tunnel on the hub. All other traffic is sent clear for the ISP. So, indeed, the HUB is the gateway for the LAN within the tunnel.

  There is a featur default on the 3000 gateway Tunnel, but that's for a different purpose

  http://www.ciscotaccc.com/security/showcase?case=K81543933

• Remote vpn client can't access outside networks

  I configured a remote vpn ASA 5510 the wizard remote vpn. Users are able to get the vpn connection and access the internal network; but IMPOSSIBLE to

  access the outside network. (For the internal network, I want to talk about network behind the vpn to ASA, outside networks refers to society outside the ASA).

  In short, the external network of the company has default route to the ROUTER1 points. The ROUTER1 has road for access network and a default route to the internet. The ASA has a default route to the ROUTER1 points. the ROUTER1 also has a route to the address of the user remote vpn refers to the ASA.

  Hope it wise.

  But I don't know if my nat statement is correct. below is my statement of nat, is there something obvious lack? There is no translation network here, routable internet addresses.

  NAT (inside) 0-list of access inside_nat0_outbound

  public static 111.1.0.0 (Interior, exterior) 111.1.0.0 netmask 255.255.255.0

  public static 111.1.1.0 (Interior, exterior) 111.1.1.0 netmask 255.255.255.0

  public static 111.1.2.0 (Interior, exterior) 111.1.2.0 netmask 255.255.255.0

  networks outside the company (111.1.3.0/24; 111.1.4.0/24)

  |

  |

  the user remote vpn <-------------->internet <--------------------->ROUTER1 - ASA - Cat6509 - inside the network

  Any suggestion is appreciated.

  Thank you

  have you enabled "same-security-traffic intra-interface.

• Cisco ASA 8.4 (3) remote access VPN - client connects but cannot access inside the network

  I have problems to access the resources within the network when connecting with the Cisco VPN client for a version of 8.4 (3) operation of the IOS Cisco ASA 5510. I tried all new NAT 8.4 orders but cannot access the network interior. I can see traffic in newspapers when ping. I can only assume I have NAT evil or it's because the inside interface of the ASA is on the 24th of the same subnet as the network interior? Please see config below, any suggestion would be appreciated. I configured a VPN site to another in this same 5510 and it works well

  Thank you

  interface Ethernet0/0

  Speed 100

  full duplex

  nameif outside

  security-level 0

  IP x.x.x.x 255.255.255.240

  !

  interface Ethernet0/1

  Speed 100

  full duplex

  nameif inside

  security-level 100

  IP 10.88.10.254 255.255.255.0

  !

  interface Management0/0

  Shutdown

  nameif management

  security-level 0

  no ip address

  !

  permit same-security-traffic inter-interface

  permit same-security-traffic intra-interface

  network of the PAT_to_Outside_ClassA object

  10.88.0.0 subnet 255.255.0.0

  network of the PAT_to_Outside_ClassB object

  subnet 172.16.0.0 255.240.0.0

  network of the PAT_to_Outside_ClassC object

  Subnet 192.168.0.0 255.255.240.0

  network of the LocalNetwork object

  10.88.0.0 subnet 255.255.0.0

  network of the RemoteNetwork1 object

  Subnet 192.168.0.0 255.255.0.0

  network of the RemoteNetwork2 object

  172.16.10.0 subnet 255.255.255.0

  network of the RemoteNetwork3 object

  10.86.0.0 subnet 255.255.0.0

  network of the RemoteNetwork4 object

  10.250.1.0 subnet 255.255.255.0

  network of the NatExempt object

  10.88.10.0 subnet 255.255.255.0

  the Site_to_SiteVPN1 object-group network

  object-network 192.168.4.0 255.255.254.0

  object-network 172.16.10.0 255.255.255.0

  object-network 10.0.0.0 255.0.0.0

  outside_access_in deny ip extended access list a whole

  inside_access_in of access allowed any ip an extended list

  11 extended access-list allow ip 10.250.1.0 255.255.255.0 any

  outside_1_cryptomap to access extended list ip 10.88.0.0 255.255.0.0 allow object-group Site_to_SiteVPN1

  mask 10.250.1.1 - 10.250.1.254 255.255.255.0 IP local pool Admin_Pool

  NAT static NatExempt NatExempt of the source (indoor, outdoor)

  NAT (inside, outside) static source any any static destination RemoteNetwork4 RemoteNetwork4-route search

  NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork1 RemoteNetwork1

  NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork2 RemoteNetwork2

  NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork3 RemoteNetwork3

  NAT (inside, outside) static source LocalNetwork LocalNetwork static destination RemoteNetwork4 RemoteNetwork4-route search

  !

  network of the PAT_to_Outside_ClassA object

  NAT dynamic interface (indoor, outdoor)

  network of the PAT_to_Outside_ClassB object

  NAT dynamic interface (indoor, outdoor)

  network of the PAT_to_Outside_ClassC object

  NAT dynamic interface (indoor, outdoor)

  Access-group outside_access_in in interface outside

  inside_access_in access to the interface inside group

  Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1

  dynamic-access-policy-registration DfltAccessPolicy

  Sysopt connection timewait

  Service resetoutside

  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

  Crypto ipsec transform-set esp-ikev1 esp-md5-hmac bh-series

  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

  Crypto-map dynamic dynmap 10 set pfs

  Crypto-map dynamic dynmap 10 set transform-set bh - set ikev1

  life together - the association of security crypto dynamic-map dynmap 10 28800 seconds

  Crypto-map dynamic dynmap 10 kilobytes of life together - the association of safety 4608000

  Crypto-map dynamic dynmap 10 the value reverse-road

  card crypto mymap 1 match address outside_1_cryptomap

  card crypto mymap 1 set counterpart x.x.x.x

  card crypto mymap 1 set transform-set ESP-AES-256-SHA ikev1

  card crypto mymap 86400 seconds, 1 lifetime of security association set

  map mymap 1 set security-association life crypto kilobytes 4608000

  map mymap 100-isakmp ipsec crypto dynamic dynmap

  mymap outside crypto map interface

  crypto isakmp identity address

  Crypto isakmp nat-traversal 30

  Crypto ikev1 allow outside

  IKEv1 crypto ipsec-over-tcp port 10000

  IKEv1 crypto policy 5

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 1

  life 86400

  IKEv1 crypto policy 50

  preshared authentication

  the Encryption

  md5 hash

  Group 2

  life 86400

  IKEv1 crypto policy 60

  preshared authentication

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 70

  preshared authentication

  aes-256 encryption

  sha hash

  Group 1

  life 86400

  IKEv1 crypto policy 90

  preshared authentication

  aes encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  Console timeout 0

  management-access inside

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  internal BACKDOORVPN group policy

  BACKDOORVPN group policy attributes

  value of VPN-filter 11

  Ikev1 VPN-tunnel-Protocol

  Split-tunnel-policy tunnelall

  BH.UK value by default-field

  type tunnel-group BACKDOORVPN remote access

  attributes global-tunnel-group BACKDOORVPN

  address pool Admin_Pool

  Group Policy - by default-BACKDOORVPN

  IPSec-attributes tunnel-group BACKDOORVPN

  IKEv1 pre-shared-key *.

  tunnel-group x.x.x.x type ipsec-l2l

  tunnel-group ipsec-attributes x.x.x.x

  IKEv1 pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  !

  global service-policy global_policy

  Excellent.

  Evaluate the useful ticket.

  Thank you

  Rizwan James

• Win 7 VPN client cannot access remote resources beyond the VPN server

  I have a Win 7 laptop with work and customer Win 7 VPN set up, and through it that I can access everything allowed resources on the remote network.

  I built a new computer, set up the Win 7 client with the exact same parameters everywhere, connected to the VPN with success, but can not access any of the resources on the remote network that I can on my laptop.

  Win 7 64 bit SP 1

  I did research online and suggestions have already had reason of my new set up.  In addition, I have a second computer that I've set up the VPN client, and I'm having the same problem.  VPN connects successfully, but is unable to access the resources.

  Tested with firewall off the coast.

  Troubleshooting Diagnostic reports: your computer seems to be configured correctly, distance resources detected, but not answered do not.

  I created another VPN client on the new computer to another remote network and everything works perfectly.

  Remember the old VPN connection to the remote network that does not work on the new computer works perfectly on Win 7 64 bit laptop computer.

  So, what do I find also different between identical configurations "should be" where we work and two new machines is not?

  It must be something stupid.

  Hello

  This question is more suited for a TechNet audience. I suggest you send the query to the Microsoft TechNet forum. See the link below to do so:
  https://social.technet.Microsoft.com/forums/Windows/en-us/home?Forum=w7itpronetworking

  Please let us know if you have more queries on Windows.

• How my client can obtain an overview of the new site, I do it for him?

  Without taking the print screens. Is it possible that I could send him an 'intermediate' for his site address?

  Once published, you can keep the publication to the same URL with the updated changes to your site, and the client can access every time the same URL to see the site updated.

  See you soon

  Parikshit

• PIX of Concentrator VPN tunnel, can I NAT traffic before the tunnel?

  I have a tunnel IPSEC of PIX-to-VPNConcentrator.

  I have a localhost on my PIX inside interface with the IP 192.168.5.5 but the site on the end of the tunnel VPNConcentrator wants to see the IP 192.168.77.9 (because they use the 192.168.5.x network to an end for another use)

  I know how things NAT from inside out, but I never have NAT - ed before traffic tunnel.

  Can I NAT a local inside IP address BEFORE traffic hits the tunnel?

  Yes, it is possible. Please see the below URL for the configuration details:

  http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a00800949f1.shtml

  Kind regards

  Arul

• Amount of the ACLs on an interface of the PIX

  Hi all

  I just wanted to know how much group-access entry (s) that you can attached to a 515ER PIX interface? I wonder if it's the same rule as the router, IE 1 ACL/interface/direction. En thank you your help.

  Hi Vincent,.

  You can apply to a single group-access on any pix interface... is not like in a router in a router, you can apply groups of incoming/outgoing access... On a pix you can apply only inbound access-groups...

  I hope this helps... all the best...

  REDA

• Creating a new interface on the Pix 516F

  I've created and activated a new interface (DMZ) on a 516F Pix. In the MDP a default outbound rule was automatically created for this interface. I could get out to the internet without any problem. However, I need to open some ports in the DMZ to the inside interface. When I add a new access rule, the outbound rule disappears and I can no longer to the internet. I tried to recreate a similar rule to allow all tcp traffic to the external interface of the demilitarized zone. The MDP has accepted the rule, but when I went back to look at it, the rule has been changed from the outside to the inside.

  How can I maintain the default outbound rule and always open ports inside?

  Thank you

  Nick

  In General:

  allow access to your internal network (web servers, printers, regardless.) (BE SPECIFIC!)

  deny all access to your internal network (deny ip no matter what subnet)

  allow an ip

• RV082 VPN Client can connect only for 6 minutes

  Hello

  I have a RV082 with firmware 1.3.98 - tm.

  The problem I have is that a Client with Windows XP SP3 can connect only for 6 minutes exactly.

  In addition, a windows appears on the client saying that the remote system is not respoding and asking to wait or not.

  We have also applied fix for Windows XP described here:

  http://www.linksys.com/servlet/Satellite?blobcol=urldata&blobheadername1=Content-Type&blobheadername2=Content-Disposition&blobheadervalue1=text%2Fplain&blobheadervalue2=inline%3B+filename%3DQVPN%2BClient%2Bv1.2.11%2BRelease%2BNote.txt&blobkey=id&blobtable=MungoBlobs&blobwhere=1193800512161&ssbinary=true&lid=3723833685B09

  http://support.Microsoft.com/kb/889527/en-us

  I have restart the RV082. What can I do else?

  Thank you very much

  Oliver

  The problem was the NAT in the ADSL modem. I tryied changing the ADSL modem and the problem is solved.

  Thank you

  Oliver

• AnyConnect VPN client can be used for IPSec remote access VPN connection?

  I think I heard it somewhere that AnyConnect VPN can be used for connections SSLvpn IPSec VPN. Is this possible? Thank you!

  No, the Anyconnect software cannot be used to establish the framework for a VPN IPSEC IKE.

• Data type can be same base on the table source for blank column

  We have an employee as mentioned structure table.
  
  EMPNO NUMBER 4,
  ENAME VARCHAR2 (10),
  USE VARCHAR2 (9).
  MGR NUMBER 4,
  HIREDATE DATE,
  SAL NUMBER (7.2).
  NUMBER (7.2), COMM.
  DEPTNO NUMBER (2)
  
  I want to create a basic view on the length of data type of same/exact structure. So is it possible that when the view was created, we can define a data type.
  
  In fact, I need to create a view based on above structure but want get deptno and sum of the salary of emp table column, and the rest of the column will be blank.
  
  Thank you

  You can use CAST

  create or replace view vu1 as
  select cast(null as  VARCHAR2(10) ) as ENAME,
   ....
  

• Oracle apex 5.0: pass values from one page to the other as well save you can save same value in the table.

  I use oracle apex 5.0

  Issues related to the:

  (1) I created an application where I have a form on which I have a button named 'Add', now if I click on that button values need to be stored in table.how to create! I use the dynamic button that is created by the html tag < input type = "button" > need help with this.

  (2) if the value stored in the table how the same value will be on the agenda of the calling page. ?

  New to this world of Apex.

  concerning

  Pranav shah

  http://zderadicka.EU/Apex-dynamic-actions-with-report-region/

• I need some help please (Horizon View Client can) do not connect to the server of connection, invalid key license server connection

  Dear professionals

  I am trying to connect to connect to the server via the Client view Horizon but when I enter the IP of the server connection I got the error message indicating that

  connection to the server was not a valid license key (see attached photo)

  everything has been installed and configured correctly, I added the vcenter Server view Portal administrator and I also added new swimming pool inside

  See administrator portal, but I don't have the login server license key.

  should I really buy the connection to the license key server? is there any version of the elevation of the connection to the server?

  Please help me

  Thank you

  naoufl

  Yes you need a license key to use the view of the Horizon, there is a 60-day evaluation license if you register here:

  Try VMware view Horizon: Access virtual office

• Lab environment, IPSEC VPN works, but can't ping Interfaces

  Hi guys

  I'd appreciate a hand with a problem I have with the installation in a lab environment. I'm sure that there is something really simple, I missed... maybe you know what it is.

  The fundamental problem is, since a host in "Location A" I can ping any host in the 'Place B' interface through a vpn ipsec standard except the inside of the remote pix that I am logged in via vpn. I am unable to ping/open PDM inside the interface of a host 'site A' in 'Site B', I am also unable to ping/open PDM inside 'Site B' of a host interface in"location".

  Here is the structure of the network

  (THE HOST'S)-(PIX501)-(HOST B) (PIX515)

  If you could have a look at the configs would be great.

  http://users.TPG.com.au/roblyon/501.txt

  http://users.TPG.com.au/roblyon/515.txt

  Thank you

  Rob

  In earlier versions 6.3, the behavior you report was not authorized by its design. This follows the same logic that prevents you from ping the external interface of the PIX to the location from a host inside the PIX instead of A. In general, a package needs a different input and output interface. When you try clicking a remote interface on a PIX, the package never actually gets to the buffer to send to the remote interface. Therefore, it is denied.

  Now, having said that... we have a solution in version 6.3 code (as you may have guessed from my earlier statement). Take a look at the command "access management". This allows for certain functions on the inside interface of the remote PIX * if * the traffic comes through an IPSec tunnel.

  http://www.Cisco.com/univercd/CC/TD/doc/product/iaabu/PIX/pix_sw/v_63/cmdref/Mr.htm#wp1137951

  I hope this helps.

  Scott