AAA

Similar Questions

• How to access the AAA columns and later using ExcelRowColToRange.vi

  Hello

  I have a huge database that I need to write on Excel in the first row, so I need to access the columns AAA, AAB...

  But using ExcelRowColToRange.vi I'm able to go up to column ZZ. Can someone please suggest a way to modify this VI to meet my need.

  Thank you

  Hi panka.

  try this one...

• measurement of voltage battery pinout 1.5 V AAA DC with acquisition of data USB-6009

  Hello, I have a very basic question with pinout when measuring 1.5 V voltage on a USB DAQ 6009, using an AAA battery. Is it okay to connect (+) to AI0 and (-) to such AI4 suggested in MAX?

  Nothing else required?

  (attached pinout)

  Thank you

  Hi feanorou,

  Yes, you have the Terminal configuration as award-winning, then using the 0 pine as AI (GOT 0 +) and using PIN 4 HAVE (I - 0) is a good setup for measuring the AAA battery.

• EEM to circumvent AAA

  Dear all,

  I'm running into a problem with an old script IOS and EEM like I can't do work around the AAA.

  So I have a script that needs to log config mode and close an interface if an event occurs. Write the scenario is not a problem.

  But to make it work! We have Ganymede + and to make it work on the router, I need a user authenticated. Or I have to log in to a router in a way that the Ganymede + is bypassed.

  The config does not support the feature known EEM 3.1 - event manager applet work around auth...

  I did the script and the ring road, by putting in place a the indicated below:

  !

  local EEMScript AAA authentication login

  activate the default AAA authentication no

  EEMScript AAA authorization exec no

  AAA authorization commands 0 EEMScript no

  AAA authorization commands 1 EEMScript no

  AAA authorization commands 15 EEMScript no

  !

  username secret privilege 15 EEMScript 5 XXXXXXXXXXXXXXXXXXXXXXXXXXX

  !

  line vty 0 2

  exec-timeout 1 0

  privilege level 15

  authorization controls EEMScript 0

  authorization controls 1 EEMScript

  authorization controls EEMScript 15

  exec authorization EEMScript

  authentication of the connection EEMScript

  length 0

  nun entry transportation

  transport of output no

  4

  Event manager session username EEMScript cli

  However, in this case, the problem is that if I connect to this router I either connected to the vty 0 - which means I can't be authenticated by the GANYMEDE as not his vty lines 0-2 set. Which means the router becomes unmanageable...

  On the other hand the solution works! Because if I'm not connected on the script will use the vty 0 by default, which as you see is 'proper' installation do not use AAA - but I need a little modification.

  That's the real question:

  Can I force my EEM script to use a specific vty line? as Vty 20 I will never use?

  The best solution or ideas would be appreciated!

  "HW is 1841 - c1841-advipservicesk9 - mz.124 - 17.bin".

  Once attempts are deferred on the RADIUS server group, how can set you a timer on the method list to be restored in the local user database?

  A problem I see is that the ACS server crashes and is accessible by intellectual property, however, he don't respond with an accept or reject.  Therefore, no one is able to connect to all devices.

  Thank you!

• IPsec IKEV2 Cisco AAA server

  Nice day

  Is it possible to configure the VPN Ipsec IKEv2 without AAA server? Or the use of any the less the ASA 5508 x as an AAA server for VPN users?

  Hello

  I have attached the screenshot ASDM to do LOCAL authentication and assignment of DHCP addresses for VPN users.

  Kind regards

  Aditya

  Please evaluate the useful messages and mark the correct answers.

• AAA authorization command console

  Hello

  I don't really understand the need of the command ""console permission aaa "."

  In fact we often set up these lines, which I already ar Editions by default VTY, Console, etc... :

  AAA authorization exec default group Ganymede + authenticated if

  AAA authorization commands 15 default group Ganymede + authenticated if

  Am I wrong? Or these lines only apply to the VTY linse?

  Thank you in advance

  In the IOS default Cisco does not permit on the console. When you configure aaa authorization, it is applied to vty but not to the console. Basically, it's to make it harder for lock you to in the router or switch. If you want permission to apply on the console then you must explicitly configure (and be very very careful that it is configured correctly, or you can wind up being locked out of the router - think especially how it will work when you can't get to the external aaa server that normally makes the authorization).

  HTH

  Rick

• AAA support on IPS modules

  Hello

  Anyone know if/when the aaa support will be added to the IPS software?

  Thank you

  Andrew.

  Not a technical reason; just a matter of resources.

  Not enough engineers to do the features both features should be a priority for each version. AAA has not made it to the top of the list of priorities at the moment.

• banner of AAA authentication

  I have configured the banner authentication aaa and aaa fail message on a router running 12.1 (15) - authentication is done by ACS 3.0.2 which works very well.

  Problem - the banner of authentication does not appear (nothing is outside of "username:"-don't not even 'check' user access) If you enter a wrong password, but the failure message. If I console in and unplug the interface while the two messages very well.

  Workaround solution - if I set up a connection "banner" then everything works fine too, but I can't work out why does not display the "banner of aaa authentication."

  I suspect ACS prevents the message, but I can't work out how - can anyone suggest a solution?

  Thank you very much!

  By the way that the command "radius-server administration '? It doesn't seem to be documented, and it has no effect or not.

  The banner command does not work if you make the RADIUS authentication, it will not work if you do a RADIUS/local/etc. This is normal, cause with Ganymede you can have the sending server banner and guests down (even if with all I don't think that you can do) and so if you have configured authentication GANYMEDE the router does not take into account the banner command and waits to see if she gets a new one from the server RADIUS itself. If it is not it will simply display the usual guests.

  As for the 'radius-server admin' command, honestly, I have no idea, never seen anyone use. Online help says "start the daemon of Ganymede management administrative messages", but what really I don't know, maybe someone else can help.

• LEAP authentication fails; that means this exit "debug aaa VAC?

  I'm trying to authenticate from laptop (client of JUMP) and I do not succeed. Can you help me understand what the problem is?

  Comment: Please find attached out of "debug aaa authentication" starting from the journal of Cisco Aironet and 'ACS failed attempts' respective.

  Please note that the ACS 3.3, "Network Configuration", "Devices-> installation of the AAA Client to the AP1", I entered a value for the field "key". However, I found this 'key' in my configuration of gateway as indicated in the attached file. Can you please confirm if I should set up such "Key" and what is the command to do this in access point?

  Thank you very much!

  Marlon

  Marlon,

  at the end of this command:

  RADIUS-server host 163.77.93.83 auth-port 1645 acct-port 1646

  You can add a 0 and the key you defined on the AAA server.

• AAA of VPN3k authentication for accounts of Mgmt

  I see that I can implement CS - ACS to authenticate the accounts of administration for my VPN3k (ver 4.x). A few questions if anyone knows.

  1. What is the behavior if no AAA server is available? Access to the consoles of the is the only option, or it will revert to the accounting configured locally on the hub?

  2. is there another way other than the restriction of access to the CS - ACS to limit admin? In other words, it seems that all those configured in CS - ACS with the level of privilege at an appropriate level and shell permissions will be able to administer VPN concentrators.

  The level of privileges assigned to the user of the CSA must match the VPN3000 user privilege level, so that the user gets some privilege assigned in the GUI of 3000.

  The configuration example is somewhat misleading for this, I've been after them to change it for a while. Basically, as soon as you add an AAA Admin Server in the config of 3000, then the 3000 will use this external server. The names of users on the 3000 (admin, config, isp, GIS, user) at this stage now mean nothing. The only thing that is checked is the privilege level assigned to the title of each of these users, and it is compared the level of privilege assigned on the RADIUS server. So basically, you go under the "admin" user 3000 and set the privilege level of say, 15 and the "config" user gets say, 11 and the user gets "div" say, 9. Then the server RADIUS configure you your users with permissions Exec (shell), and the privilege level of say, 15. When this user logs in the 3000, it gets the rights that the user "admin" has, because his level of privileel is the same. If on the RADIUS server, you set the level of privilege to 9, then he would get the rights available to the user 'div '. The username on the 3000 is meaningless, the only things that are being matched are the privilege level and from there, the permissions are affected accordingly.

  Hope that makes sense. The sample configuration shows a user "admin" being added to the ACS server, but it is misleading because it makes people think that the GANYMEDE username must be equal to 3000 username, this is NOT the case. The GANYMEDE username can be anything, and that the user will get the permissions through the hub based on what the user 3000 has the EXACT same privilege level set in place.

• Issue of AAA - Line Con 0 = login authentication (password)

  Good afternoon everyone,

  A simple nice for someone I am sure... I only of remote access to the network kit and therefore cannot test access to the Console.

  I have a switch with the following configuration (excerpt)

  !

  Password username Admin Password123

  !

  AAA new-model

  AAA authentication default login group Ganymede + local

  !

  Line con 0

  Cisco connection authentication (where cisco is representative of a password)

  NOTE: I have not username cisco password Admin in global config

  My question is: with this current config access Console will stop using the configuration of default Ganymede for authentication and don't allow access to the line of the console if the cisco password is specified? In this case that the password is not defined in a global access, would be denied?

  I've seen it before where you have exactly the same set up, but instead of referring to a value of password on the console line, you specify a list of names.  For example, authentication of connection local CONSOLE_USERS, which would make sense, because you would be referring to a group on the Ganymede server named CONSOLE_USERS and only users defined in this group could access through the console, while the ACS server is running!

  Any assistnace appreciated as I really want to get my head around ACS unconditionally

  Thanks in advance

  David

  Yes, David, you can safetly delete this "authentication to connect cisco" line con 0.

  About radius server take a look on:

  http://www.shrubbery.NET/tac_plus/

  On the radius server, I recommend freeradius for these tests.

  (there much capacity of fever, then cisco ACS, but it can allow you easy test of the basic functions)

  ---

  Michal

• LDAP AAA for VPN configuration

  Preface: I'm all new to Cisco Configuration and learn as I go.

  I'm at the stage of configuration LDAP to configure a VPN on ASA 5520, software release 8.3 (1).  Previously the programme installation and RADIUS authentication successfully tested, I tried to use similar logic to implement the LDAP authentication/authorization.  I have acquired a service account that queries the pub for the identification of the registered user information.  My main resource was the following Manual: Cisco ASA 5500 Series Configuration Guide using the CLI Software Version 8.3.  I did initially configurations by using ASDM, but could not get tests to succeed.  So I amazed the ASDM configs and went to the CLI.  Here is the configuration.

  AAA-server AAA_LDAP protocol ldap
  AAA-server host 10,20,30,40 (inside) AAA_LDAP
  Server-port 636
  LDAP-base-dn domain.ad
  LDAP-scope subtree
  LDAP-naming-attribute uid
  LDAP-login-password 8 *.
  LDAP-connection-dn cn = commonname, OU = ou01, or = ou02, dc = domain, dc = ad
  enable LDAP over ssl
  microsoft server type
  LDAP-attribute-map LDAP_ATTRIB

  ---

  type tunnel-group ASA_DEFAULT remote access
  attributes global-tunnel-group ASA_DEFAULT
  authorization-server-group AAA_LDAP

  ---

  LDAP attribute-map LDAP_ATTRIB
  name of the MemberOf IETF Radius-class card
  map-value MemberOf "VPN users' asa_default

  ---

  I tested all the naming-attribute ldap alternatives listed with the same results.

  When I test the authentication using this configuration, I get the following error: ERROR: authentication server does not: AAA Server has been deleted

  When I test authorization using this Setup, I get the same error (except for the word permission instead of authentication).

  I am at a total loss.  Any help would be appreciated.

  I would use ldp.exe to see if you can make sure that the sytnax of your ldap-connection-dn is just as you have in your config, it really helps just copy and paste.

  The problem I see is the following:

  [210] link as st_domadm
  [210] authentication Simple running to st_domadm to 10.20.30.30
  [210] simple authentication for st_domadm returned credenti invalid code (49) als
  [210] impossible to link the administrator returned code-(1) can't contact LDAP er

  I suppose your ldap-connection-dn is st_domadm and you try to test with the administrator account?

  Thank you

  Tarik

• ACS 5.4 ASA 8.2.5 disable AAA for the particular user

  Hello!

  I want to disable journaling Ganymede + for the particular user. This user is used only for automated (python script) pooling of vpn tunnel ASA (limited command set - permission on ACS) group to verify the number of users authenticated via VPN. The problem is that this user generate a bunch of logs according to authentication authorization and accounting on ACS. Is there a solution, disable Ganymede + newspapers on ACS for this particular user? Maybe it is possible to modify the AAA on ASA to not connect this particular user?

  Thanks in advance.

  Hi Pawel,

  You can create filters collection for that specific user. When you configure monitoring filters & Report Viewer does not record these events in the database.

  Navigate to: Configuration of the analysis > System Configuration > filters Collection > add a filter

  What follows is the attributes that can be used. You must use the user.

  -Access service

  -User

  -Mac-add

  -Nas - IP

  Example: We get several hits of ASA by 'user' and we want ACS to ignore it. Create a filter by using the user. ACS must now ignore any attempt from the IP Address of the NAS.

  Jatin kone
  -Does the rate of useful messages-

• the AAA authentication enable default group Ganymede + activate

  I implement CSACS 4.0. First of all on the client, I will apply aaa authenticatio / authorization under vty. The issure if I use the followin command

  the AAA authentication enable default group Ganymede + activate

  What happens if I connect via the console? I need to enter a name of user and password?

  Here is my configuration

  AAA new-model

  Group authvty of connection authentication AAA GANYMEDE + local

  the AAA authentication enable default group Ganymede + activate

  authvty orders 15 AAA authorization GANYMEDE + local

  RADIUS-server host IP

  Radius-server key

  Ganymede IP source interface VLAN 3

  AAA accounting send stop-record an authentication failure

  AAA accounting delay start

  AAA accounting exec authvty start-stop group Ganymede +.

  orders accounting AAA 15 authvty power group Ganymede +.

  AAA accounting connection authvty start-stop group Ganymede +.

  line vty 0 15

  connection of authentication authvty

  authorization orders 15 authvty

  authvty connection accounting

  accounting orders 15 authvty

  accunting exec authvty

  Any suggestion will be appreciated!

  It should work because it is a guest message.banner whenever you try to connect (console/vty). I set it up on my router.

  If you have banner motd, it will appear as well (see below). So, I have to remove it to get only the aaa banner & prompt is displayed:

  ************************************************************

  Username: cisco, password: cisco (priv 15f - local) *.

  ************************************************************

  Any unauthorized use is prohibited.

  Enter your name here: User1

  Now enter your password:

  Router #.

  The configuration more or less looks like this:

  AAA new-model

  AAA authentication banner ^ is forbidden to use CUnauthorized. ^ C

  AAA authentication password prompt "enter your password now:

  AAA-guest authentication username "enter your name here:

  Group AAA authentication login default RADIUS

  local authentication AAA CONSOLE connection

  HTH

  AK

• Configure a router AAA TACCAS

  I have install ACS 4.0 server but I can't work with tricky ror swich can someone send a confiuracion for me on the server and the router works well.

  The missing part was 'aaa authentication login default group Ganymede + local', allow instead of connection (mixed-up...)

  For some devices (aaa authentication TELNET connection group Ganymede + local), while others default (aaa authentication login default group Ganymede + local).

• Need help with the configuration of the AAA

  I try to configure AAA on my network devices. I use GANYMEDE + with an ACS (3.2) server. I have groups of users of installation against two in the ACS, 1 voice server and allow privileges and the other without. I am able to get the AAA configuration to work when telnet in devices. However, when you connect in the port of the console, the user with privileges to activate Group do not go directly in the activation of the mode as do the users of telnetted. How to solve this problem?

  Hello

  You should not use the following command: -.

  authorization AAA console

  This command will not be displayed on the help.

  Kind regards

  Vivek