Configure a router AAA TACCAS

Similar Questions

• How can I configure my router to a new modem?

  I changed my internet provider and I have a new modem. How can I configure my router to work with my modem?

  Hi @Belem,

  You can check out the link below and see if it helps.

  http://KB.NETGEAR.com/app/answers/detail/A_ID/22697

  Kind regards

  Dexter

  The community team

• Need help Configureing Netgear router so I can connect to Playstation Network.

  My playstation 3 says "Failure of Type NAT" and will not sign into the playstation network. I have a router Netgrear that connect PS3 to Internet, but times out when you try to connect to the PS network. How can I configure the router? I use a wired connection.

  Hello

  I suggest you to contact the manufacturer of the playstation for assistance on this issue.

  Thanks and greetings
  Umesh P - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  [If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message.] [Marking a post as answer, or relatively useful, you help others find the answer more quickly.]

• How to configure the router Linksys DD - WRT for WVC54GCA E4200

  I don't know how to configure the router Linksys DD - WRT for WVC54GCA E4200. DD - WRT is very complcated. Help, please! Also, I used the TZO.com to the DDNS. Can I set up the DDNS for DD - WRT router? I used the DDNS to my old model router before. Thank you.

  I followed the TZO supporter last night. I can watch my WVC54GCA outside. All solution links:

  http://tzodns.com/support/tutorials/188

  http://tzodns.com/support/tutorials/190

  Hi Majekho,

  Your domain name has decided to 99.245.xx.x. If you go to www.test.tzo.com from the location of the host, you must see this IP address. If these numbers are the same, then all with TZO works correctly. I guess that it is a simple problem with ports (80, 1024) is not open in the router and forwarded to the right internal IP address of the device (for example. 192.168.1.xxx).

  In addition, if you have a DSL, you will need to call your ISP and ask them to show you how to put your modem in "bridge mode". This will disable the firewall in the modem that blocks incoming connections even if you open ports in your router.
  In addition, during the test, it is best to test on your device remotely, this is due to a common problem called loopback with most routers. For more information about looping, take a look at:

  http://helpdesk.TZO.com/cgi-bin/KB.cgi?view=140

• I have Windows 8 and that you can't find the woreless icon to configure my router

  I have HP envy23, Windows 8 and that you do not find the wireless icon to configure my router.

  When you request support, please provide the complete product of the HP computer in question number. HP/Compaq made thousands of computer models which are all different. Without this information, it can be difficult, even impossible to help you solve your problem.

  The information requested above are at the bottom of your computer or inside the battery compartment.

  If you try to connect to a wireless network, type "connect to a network" on the new Windows 8 Office as shown in the following example.

  

  Please click the White Star of KUDOS to show your appreciation

• Configure the router Cisco E2000 wireless for my laptop HP with Vista, I can't work.

  Configure the router Cisco E2000 wireless for my laptop HP with Vista, I can't work.  I spoke with Cisco and they said that my Atheros AR5007 adapter does not work with Cisco E2000 and contact my computer vendor

  Hello

  HM... I guess that the Cisco people know what they're taking everything. The AR5005 is a b/g card and there should be a good reason to not work with a router that is able (the E2000 is able g) g.

  This is HP drivers for the card, http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?cc=us&lc=en&dlc=en&softwareitem=ob-55737-1

  If you can't make it work, you must decide between a new card or another router.

  Personally, if it's new and I could return it, I'd get a different router model. But YMMV

  ------------

  My posts reflect my understanding and experience. It does not necessarily reflect the opinion or the vision of Microsoft, or anyone else.

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Configure L3 routing with different suppliers

  Hello people, I am not used to work with layer 3 switches, so I need your help:  I have two different sites. Each site has one switch L3 and  networks like the example below:
  
  Switch A (power connect 6224):Network 192.168.0.0 /24
  
  Switch B (Cisco 3560)Network 172.19.16.0 /24network 10.10.10.0 /24
  
  I need to configure both sites to comunicate witch each other. I have the following idea:
  
  - Connect a Cable between two switches- Create a vlan on each switch and configure the ips like below:Switch A: interface ethernet 1/g1 - 10.0.0.2Switch B: interface gigabit 1 - 10.0.0.3- Configure static route on each switch like:Switch A: ip route 172.19.16.0 255.255.255.0 10.0.0.3     ip route 10.10.10.0 255.255.255.0 10.0.0.3Switch B: ip route 192.168.0.0 255.255.255.0 10.0.0.2
  
  Is this possible? Is this configuratios right? If so, do I need to improve something else?
  
  A appreciate any help.
  

  The decisive factor here is going to be if the PowerConnect and Cisco have different Broadcast domains from each other. If they have a separate broadcast domain, then the method you mentioned should work fine. If they share broadcast domains, then you want the physical connection to the two switches in general or Trunk mode, allowing the VLANS on the connection.

• Please help to configure the router for internet connection 871W!

  Hello world!

  I just started styding for CCNA, so I'm totally new to Cisco stuff. Recently bought a router 871W and spent two days in a row trying to configure internet connection with no luck! I use the port console for the configs and SDM/CCP. Would be greateful if someone could tell me how to do simple configs of internet connection. I googled everything but it's still confusing. I can't assing all-IP ports FA 0-3. I used instead of the VLAN. But all tutorials use FA0 and when I try to assign an IP address to FA0 it gives me some L2 cannot be assigned or something... :/ And I am also confused at what address IP use for WAN.

  I connected the cable between the Modem and the LAN of the PC port and copied some IP addresses which I think I have to use to configure the router for internet connection. And here they are:

  ISP IP: 76.114.54.255

  SUBNET: 255.255.248.0

  GATEWAY: 76.114.48.1

  DHCP: 69.252.97.4

  DNS: 75.75.75.75

  75.75.76.76

  If you can, please help! Thank you!

  Hi david,

  Looks like your 871w can not get a dynamic IP address: % unknown DHCP problem... No possible allocation

  you could ask your ISP to perform a reset/clear MAC add and try again?

  also, kindly post lastest "show run".

  Edit: just to see you've updated your screenshot. could you add command under 4

  Mac-add 0001.4af9.8b83

• I need to configure my router once I format my OS is Windows 7?

  I need to configure my router once I format my OS is Windows 7? Thank you! -EIB

  Original title: Windows 7.

  It is not necessary. If you use the WiFi for connectivity, you must type the password, if security is enabled, connecting the first time after reinstalling Windows.

• HP ps 5520 eprint configuration which router configuration is necessary?

  I need to configure on my ps hp eprint 5520, but it cannot download the firmware. The printer is properly installed via radio one by one 192.168.xxx.xxx local/static ip, dns is the high 8.8.8.8 and 8.8.4.4. the computer is on the same local area network and 7 64 home. the router is netgear dg 834. I tried to install the printer in the demilitarized zone, I tried to inbound and outbound on port 80 to 5347 and authorized installation service.  THERE IS NO WAY TO INSTALL EPRINT.

  Thanks for advantage

  Problem is actively debated the post below.

  Photosmart HP 5520. First installation cannot start configuration eprint. Could not be updated

• How to configure my router 700 minutes using a Macbook?

  I can't configure my MN-700 router to my macbook. How can I make this cd is not able to run on the computer.

  Hello cassiusmatthews,

  You run Windows on your Mac or you run the operating system provided with the Mac (OSX)?

  I suggest that to contact Apple to help configure your Macbook computer on a wireless network:

  https://discussions.Apple.com/index.jspa

• Configure the router WRT54G with the PUBLIC IP address and use the DHCP protocol for internal computers

  Hello

  I have a service online Internet with 5 public IP addresses.

  The router and the AP are connected to a switch.

  I would like to set up a WRT54G Router with a public IP address and use DHCP (with private ip address) for the computers that will connect to the AP.

  That the AP is connected to the switch, it is possible that the other wired computers that are connected to the same switch can get an IP from the DHCP?

  Thanks in advance

  In this case, the routing is automatic.

  WRT54G configuration:

  WAN:

  Internet connection: static IP address

  IP address: 180.X. X 170

  Subnet mask: 255.255.255.248

  Gateway: 180.x.x.x (Ex: 180.x.x.1)

  DNS: servers your ISP DNS

  LAN:

  The IP address of the router: 10.10.10.1

  DHCP range: 10.10.10.100 of-online 10.10.10.200

• Configure the router linksys on windows vista

  Recently I bought a linksys wireless router and have problems when configuring it on windows vista home.

  I have read many articles that while configuration that I need to connect the DSL modem (DSL in my case) to the router (WAN port) and also a thread more (that came with the router) to the laptop. If I connect my laptop with router then how is the wireless network or if it is required to do the installation?
  Do I need a PC/laptop always connected with wireless router and then only I can take advantage of being wireless (I hope not)? When can I disconnect the cable between the router and the laptop and use internet as well?

  The reason for asking this question, is that my laptop LAN port is not functional. If I use any other laptop for the initial setup and then use my laptop to connect to the router if it works without using b & w computer laptop and router connection?

  I'm really a beginner for this please help.

  Thank you

  Hi, thanks for your answers.

  I had a temporary cell phone to set up my wireless router. The question I m is that I can access internet from my lan from the dsl model cable but I can't access the internet when I connect the LAN to my wireless router and a join cable wireless router to my laptop.

  While the configuration of the wireless router from the cd that I got with router reached the last step to find the internet connection and then pop up msg this router is not able to find the internet connection. What should I do?

  I just saw a thread (http://forums.linksysbycisco.com/linksys/board/message?board.id=Wireless_Routers&thread.id=58742&view=by_date_ascending&page=2) and cloned my mac but coldnt able address to make it work.

  I'll post my ipconfig details in a moment.

  C:\Users\Chakrapani V>ipconfig /all
  
  Windows IP Configuration
  
     Host Name . . . . . . . . . . . . : ChakrapaniV   Primary Dns Suffix  . . . . . . . :   Node Type . . . . . . . . . . . . : Hybrid   IP Routing Enabled. . . . . . . . : No   WINS Proxy Enabled. . . . . . . . : No
  
  Ethernet adapter Local Area Connection:
  
     Connection-specific DNS Suffix  . :   Description . . . . . . . . . . . : Marvell Yukon 88E8040 PCI-E Fast Ethernet Controller   Physical Address. . . . . . . . . : 00-21-9B-F1-26-C4   DHCP Enabled. . . . . . . . . . . : Yes   Autoconfiguration Enabled . . . . : Yes   Link-local IPv6 Address . . . . . : fe80::71d3:2386:391a:3d9a%11(Preferred)   IPv4 Address. . . . . . . . . . . : 192.168.1.100(Preferred)   Subnet Mask . . . . . . . . . . . : 255.255.255.0   Lease Obtained. . . . . . . . . . : 22 October 2009 07:24:15   Lease Expires . . . . . . . . . . : 23 October 2009 07:24:15   Default Gateway . . . . . . . . . : 192.168.1.1   DHCP Server . . . . . . . . . . . : 192.168.1.1   DNS Servers . . . . . . . . . . . : 192.168.1.1   NetBIOS over Tcpip. . . . . . . . : Enabled
  
  Tunnel adapter Local Area Connection* 6:
  
     Media State . . . . . . . . . . . : Media disconnected   Connection-specific DNS Suffix  . :   Description . . . . . . . . . . . : isatap.{314241DB-C984-4A60-A127-7D9246A8A709}   Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0   DHCP Enabled. . . . . . . . . . . : No   Autoconfiguration Enabled . . . . : Yes
  
  Tunnel adapter Local Area Connection* 7:
  
     Media State . . . . . . . . . . . : Media disconnected   Connection-specific DNS Suffix  . :   Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface   Physical Address. . . . . . . . . : 02-00-54-55-4E-01   DHCP Enabled. . . . . . . . . . . : No   Autoconfiguration Enabled . . . . : Yes
  
  Tunnel adapter Local Area Connection* 17:
  
     Media State . . . . . . . . . . . : Media disconnected   Connection-specific DNS Suffix  . :   Description . . . . . . . . . . . : isatap.{A1DE9DAE-229D-4929-A91E-F208BB0DCA22}   Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0   DHCP Enabled. . . . . . . . . . . : No   Autoconfiguration Enabled . . . . : Yes
  

• Help to configure the router Cisco 1941

  Help!

  I just bought a router cisco 1941, I understand, it came with the Cisco CP, but I don't know how get you to the part where I can use it.

  Also, how can I connect to the router directly without using the HyperTerminal console, all I want to be able to do is configure the address IP of the ISP and my IP address so I can use it for surfing the internet.

  Help, please.

  Hello

  Thanks for the screenshots and show the output! You will need a few lines of command for CCP to work:

  Configure the terminal

  username username privilege 15 secret PASSWORD

  IP http server

  local IP authentication

  Sent by Cisco Support technique iPad App

• Need help with the configuration of the AAA

  I try to configure AAA on my network devices. I use GANYMEDE + with an ACS (3.2) server. I have groups of users of installation against two in the ACS, 1 voice server and allow privileges and the other without. I am able to get the AAA configuration to work when telnet in devices. However, when you connect in the port of the console, the user with privileges to activate Group do not go directly in the activation of the mode as do the users of telnetted. How to solve this problem?

  Hello

  You should not use the following command: -.

  authorization AAA console

  This command will not be displayed on the help.

  Kind regards

  Vivek