AAM does not recognize the installed Apps CC

Similar Questions

• Photoshop does not recognize the installed fonts

  I installed the Aachen from Adobe fonts on my PC. Can I use these fonts in Illustrator, but Photoshop does not recognize them.

  If it is a policy that recognizes PS, you must close PS while you install new fonts.

  I don't use, so I have no way to test the CFF fonts.  I'm sorry.

  Nancy O.

• Install Windows 8 does not recognize the system drive

  I built a new machine (chart below). Since this is a new machine and not an upgrade, I bought Win 8 Pro 64 bit OEM to do a clean install. The SSD is my system disk that Windows 8 will be installed. Four data drives are mirrored, two for the other two. Construction went perfectly. The BIOS recognizes all six disks: 1 SSD, 4 HDD, 1 DVD.

  Insert and boot the disk of Windows 8. Accept the EULA, enter the product key. Arriving at the page "Where do you want to install Windows?", only four hard disks are listed. The SSD (installation to go) is not found by Win 8. ??? I tried to change ports SATA, cables, power supply - no difference. For each new change of hardware, the BIOS still sees everything. This isn't a hardware problem.

  The question remains: why the installation of Windows 8 does not recognize the SSD drive. All five disks are on AHCI. I'm not in RAID.

  I spoke with crucial technical support of all (manufacturer of the SSD). They were also surprised that the drive does not appear in the list.

  Does anyone have a solution? I spent all the money on hardware, as well as the new version of Windows and I cannot install it.

  This is the real kick in the teeth: Microsoft won't support me. The OEM of Windows 8 version is the same as manufacturers, such as Dell or HP. Support told me I had the support of the manufacturer. HA! I am the manufacturer. Either that or upgrade from an earlier version of Windows. This means that any that a new construction machine will get ZERO assumption of Microsoft. All just great.

  Thank you in advance for any assistance.

  Windows 8 Pro 64-bit (full version) - OEM
  Intel Core i5 - 3570K
  Card mother GIGABYTE GA-Z77X-UD5H
  Crucial Ballistix 2 x 8 GB DDR3 1600
  Crucial M4 2.5 "128 GB SSD (system disk)
  WD Green WD30EZRX x 4 (data readers) 3 TB drive
  Rosewill Challenger-U3 ATX Mid Tower Case
  SeaSonic M12II 620W 620 Bronze PSU
  ASUS DVD writer

  The DSS must be LOW LEVEL FORMATE.

  Once, there may be no other [HDDs] not connected to the SATA ports.

  Install Windows 8 Pro now.

  [Edit] Can someone please mark this as answered? I can't because I posted the question. Thank you.

• I am trying to install an older version of CS (CS 6). It does not recognize the serial number. What can I do?

  I am trying to install an older version of CS (CS 6). It does not recognize the serial number. What can I do?

  Hello

  Please see error "serial number is not valid for this product". Creative Suite and serial number incorrect error

  Hope that helps!

  Kind regards

  Sheena

• After you have installed Windows 10, I can no longer create a PDF of my program Pagemaker 7.0.1. Purchased Acrobat DC, but not joy. Apparently, Acrobat PDF maker does not recognize the .pmd extension. I get errors and various suggestions, but nothing work

  After you have installed Windows 10, I can no longer create a PDF of my program Pagemaker 7.0.1. Purchased Acrobat DC, but still no joy. Apparently, Acrobat PDF maker does not recognize the .pmd extension. I get errors and various suggestions, but nothing works. WHAT?

  Print to Adobe PDF? Why the * & ^ * & ^ V_ $ didn't pay a lot more money to Adobe for an Adobe program that does not work with another Adobe program? Oh, right--they want to move me up (buy) the new Adobe graphics programs. I'll keep sweating this point and will no doubt wind up forking over a thousand$ $$ or so for 'new' stuff I don't need.

• I have Digital Editions installed but when I try to download a book in my corner, it does not recognize the format of the CMHA

  I had to cancel and re - authorize my meal.  I removed my old version of Digital Editions and later installed.  I can open Digital Editions and see my latest library books, but I can't download new.  It does not recognize the format of the CMHA.  I tried to add in the file type, but it is not on the list. I checked my registry and Digital Editions is here.  I don't know what else to do here.  I'm running on Windows XP with a corner of torches and restarted my PC.  This used to work fine for me and now I can't use it at all!  Please help me!

  Thank you

  I tried both.  Actually, what I did to resolve this was to ADE 3 version to uninstall and reinstall version 2.  Not sure if it was uninstall and reinstall or version, but it works now.  Thanks for your respone!

• I just buy Photoshop and I'm going to download and Safari says it does not recognize the address

  I just buy Photoshop and I'm going to download and Safari says it does not recognize the address

  Hello

  If you purchased Photoshop CC, please go to https://creative.adobe.com/apps and log in here with your e-mail ID. If this is your first time plaese reset the password

  Search for Photoshop and start the download of Adobe Creative cloud.

  PS: Adobe creative cloud will be installed automatically

  Ankit

• Power mac g4 does not recognize the DVD/CD drive.  It has worked very well in Leapard

  I just newly installed Tiger on my PowerMac G4, and now it does not recognize the DVD/CD drive.  I did all the updates and it does not see the DVD in the DVD drive.  It works perfectly before a new clean install DVD of the Tiger.

  What is your indication that the DVD is not recognized?

  Run the utility disc with the disc in the optical drive.  The drive will appear in the sidebar of disk utility?

  I did all the updates and it does not see the DVD in the DVD drive.

  If you put another type of disc in the optical drive, as a music CD, it is recognized?

• Portege R700 - Autocad 2011 does not recognize the graphics card

  Hello

  I have toshiba Portege R700 with 64-bit win 7 installed.
  I need the computer for use with autocad 2011.

  For some reason any auocad does not recognize the graphics card installed on the computer.
  I suspect it because very little memory is allocated for the graphics card.

  How can I change with the memory allocated for the graphics card, or perhaps, can someone show me where can I find a driver that supports autocad.

  Thank you very much!

  Hello

  What Portege R700-xxx you have exactly?
  As far as I know the graphics memory cannot be assigned manually.
  Everything is controlled by the graphics driver and you have no influence on this

  You can try updating the graphics card driver maybe it would help.
  The most recent driver found on the page of the European driver Toshiba
  If not, you should check the manufacturer of the graphics chip driver

  Good luck

• Satellite 1900 (PS192E) - does not recognize the CD/DVD

  Hey all,.

  I just bought a Toshiba Satellite 1900 (PS192E) and place an old 20 GB HDD from an old laptop.

  When I boot, the screen is in VGA 16 color mode, it recognizes the DVD player, but does not recognize the CD/DVD when inserted. I tried to install and run the utility "driver robot" Toshibas, but the display is such that I see all of the screen to start the search.

  If there is someone out there who could give me some advice, I would be extremely grateful.

  Thank you very much

  James

  Hello

  OK, you have installed the disk HARD of another laptop but too format the HARD drive? I mean if the HARD drive performed from another laptop, you need to reinstall Windows because now you have other hardware installed.
  What version of Windows is it?

  If you want to install a driver for the graphics card go into Device Manager and select Update driver.

• Tecra S3: Installation of Vista does not recognize the HARD drive

  I try to install Vista Ultimate on my Tecra S3, but installation does not recognize the HARD drive.

  I tried to find the driver for Vista for my computer, but not found RAID.
  Tried it with XP drivers, but no longer works.

  Do you have an idea where I can download Vista drivers for RAID?

  THX

  Hello

  Your suggestion is good. The Tecra S3 supports the RAID, and the RAID driver is required to install the OS on the HARD drive.
  On the European driver Toshiba page I found a RAID for XP driver.

  I put t know if this driver will run under Vista, but I recommend to test.
  The RAID XP 1.3.8.0 driver version can be downloaded from this site:
  http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp?service=EU

  Please note; You can store the RAID driver on an external USB and Vista should recognize it!

  Good luck

• Satellite L30-105 does not recognize the 1 GB of additional RAM

  Hi there I hope someone can help me

  I have a Satellite L30-105 PSL33E, which came with 1 GB of ram installed (2 x 512 MB made by TeamViewer)
  and it's terribly slow with vista, not to mention programs.
  The toshiba website says max RAM is 2 GB, so I bought a Kingston 1 GB ram chip to increase the ram to 1.5 GB. I thought should try before moving to 2 GB

  However after installing memory vivid it's show still only 1 GB in windows and in the bios (894 + the rest for video). It has the latest available BIOS on the site 3.10, yet still does not recognize the chip.

  The chip is installed in the lower slot, including the original 512 at the top (closest to the keyboard)

  Are limited to only some of the Satellite of RAM?
  The old subjects indicate if kingston does not work try corsair.
  Other topics suggested to change slots
  Others suggest that it may have only two of the same ram chips in IE 2 x 512 or 2 x 1 GB, you may not have 1 of each

  Can anyone help? everyone knows about similar problems?

  I will not buy any more RAM to try different brands for the same issue to occur

  Hello

  The L30-105 is able to manage the 1024Mo modules in each location it should be able to update the RAM up to 2 GB.

  > Why the RAM 1 GB module cannot be recognized?
  Perhaps the two modules are not compatible with each other
  I would recommend using two identical modules of the same manufacturing
  I use Kingston modules, they are ok for me

• Tecra M1 does not recognize the DVD drive after replacement

  I am trying to install a new drive CD-RW/DVD-RW on a Tecra M1; However, when the computer does not recognize the drive.

  Is there a solution to this?

  Thank you

  Colin

  For me it s case.
  I would say that the BIOS can't handle the new player properly because of the wrong master/slave/c-salt settings
  Readers slim for computers laptops support setting master/slave/c-salt settings and these settings can only be changed by changing the rider as on desktop drives.
  So it is very important that you purchase a compatible player and supported because disks with incorrect settings will not work.

  Before buying a car, you should ask the service provider to Toshiba for a caught player supported and compatible

• Windows 7 64 bit does not recognize the USB external drive HARD Stor E art 3.5 "

  I buy the art external disk HARD Stor E 3.5 "and spend a few days in windows does not recognize the HARD drive. Try to connect the drive to other USB 2 ports and nothing happens. Use a USB to see if has been a problem with the USB ports, but all 3 are OK. Try it on the laptop Asus and windows 7 recognizes the HARD disk. I formatted the drive in NTFS FS. In managing records do not show the external HARD disk. What can I do to fix this?

  My laptop is a Qosmio F60

  This is a really silly situation. It can be recognized by other laptops but not your Qosmio.
  According to the description of your HARD drive when connected simply doesn t exist for your Qosmio laptop.

  Some other HDD is recognized correctly?
  What you can try is to reinstall the chipset driver, restart the laptop and test it again.

  Since when you have this problem? Some installed updates of the last days?

• Satellite A110-294 does not recognize the wireless card

  Hello

  the question is:
  Why my Satellite A110-294 does not recognize the wireless card?

  I re - install Xp PRO with all the drivers.

  I have try all the drivers Wireless: Wlan intel + proset intel atheros wlan + wlesscmgr

  I don't understand, can you help me?

  Thank you
  André

  Hello

  To my knowledge, the A110-294 uses the Atheros WLan card and therefore the Atheros Wlan dirver should be the right one.

  You can find the latest driver for Atheros WLan here:
  http://APS2.toshiba-tro.de/WLAN/

  Just a question;
  You see the local network card in Device Manager? I mean, you should see an Ethernet controller or an unknown device in the network adapters
  The driver is missing, then the device must be marked with a yellow exclamation point