waveform record NI DAMA phase coherent multi-channel

Similar Questions

• How can I get multi channel audio via the HDMI port on an early 2015 MacBook Pro?

  I try to get the 7.1 audio channels to flow from my MacBook Pro to a cinema set up. The display works fine now I plug the HDMI in however the sound still Mac speakers. I checked the settings and no HDMI output is available. An airtime option is available, but that returns only two channels as a maximum to the receiver. When I go to the configuration of the source on the receiver it receives video at 1080 p 60herts however it is specifically stated No Audio from the Source.

  Also, I have connected my iPhone 6 s more using an Apple through the same HDMI cable adapter and it works perfectly. We also use HDMI with our PS4 occasionally and it works perfectly, even with the 3D.

  Thus, the MacBook Pro is early 2015 with an i5, the receiver is a Harmon Kardon AVR 2700 (we run 7.1 channels of this) and we are connecting via the HDMI port through a 50 ft HDMI before. The receiver sends the audio to a projector with 1080 p 60 hertz if it changes anything...

  Also if it helps the receiver supports dts - hd master audio decoding, Dolby True HD/Digital Plus decoding, HDMI 1.4 (HDMI is compatible 2.0), as well as multi-channel input and PCM and linear PCM.

  I use a "Behringer UCA202' audio device I bought on amazon.com for only $29.

  It works very well for the audio 5.1 or 7.2. Works connect optical toslink. Just plug it into a usb port on your Mac and a cable optical toslink to your AV receiver.

  My Yahmaha 7.2 audio/video receiver is measuring process the digital signal in THX, DTS, Dolby digital Pro logic, a cinema, etc.

  

• Question: BDP-S570 or BX57 internet multi-channel flow?

  Hi all, I noticed recently that when I listen to the audio or video content on the network as my BDP-S570 diffuse now as a multichannel surround sound instead of the 2 stereo channels.
  I don't know if this is caused by the latest firmware I installed or changed content providers (or the Sony Server site) in a recent past a few days to send their audio in 5.1 multichannel, now. Or finally if my BDP-S570 went buggy and it's stuck in the PCM multi-channel streaming mode.
  It broadcasts my network all music and video internet connections in multichannel sound, even if I put the BDP-S570 "Downmix" mode setting of stereo 2 channels. I swear before I made this latest firmware update, I always had that 2-channel stereo audio from the internet network connections.
  So I need to know and ask if someone else becomes sound mode of 5.1 channels of their Internet stream?

  Update: too bad people, I found my answer. The cause of constantly multichannel PCM streaming of all my network connections was because I had the BDP-S570 DTS parameter defined on ' Neo: 6 Music ' instead of 'Off' in the settings menu. I set this to "off" and all the music from the internet is now back to regular 2-channel flows. for info. case solved.

  I'm glad that you managed to fix the problem yourself. If you have additional questions, please let us know and we will be happy to help you.

• Cannot create the multi channels Tx two USRP-2943Rs Session with driver

  I have problems of implementation of several USRP-2943R devices in tranmist both of their channels at once.  Right now my configuration is a configuration of four chains composed of two devices of RIO.  I am only able to transmit at the same time successfully CH0 and CH1.  I'm creating a session using two devices and my aim is to perform Tx on CH0 via CH3.  In addition, my goal is to use the LabVIEW driver without any synchronization, because I test fix synchronization through post-processing and you want the VI be as simple as possible without the hassle of FPGA programming. I realize has the Simple models OR - USRP Streaming Sync in LabVIEW, but additional synchronization and FPGA programming is too much for such a simple project like mine which would require no synchronization USRP.

  My VI and some screenshots of the error messages resulting is attached.  I am able to succesfully implement multi-channel Rx deals and attached is my multichannel Rx VI.  My question is why I can open and operate a session of Rx mult-channel without problem, while a multi-channel Tx session will give me errors?

  My final goal is to merge my multichannel work Rx VI with a mult-channel Tx VI work for measurements in order to test some synchronization post-processing routines that are performed in Matlab.

  I think that I found a solution to my problem.  I thought to post it here to help others.  It is important to use some sort of device to synchronize several USRPs.  However. I found that you must reset the device by setting the node of reset function blocks that open and session Rx or Tx.  "" If it is not defined, then the ' niUSRP Signal.vi configurethe ID of the specified attribute is not valid for the scope specified (or channel)." error occurs, any circuits that you define.  After the node Reset true and place an empty string for my channels Enabled, all was fine.  Also, a full duplex system you will be only to first log of Rx with a reset of the device, followed by the opening of a session of Tx without a reset of the device.

  One more thing, it is that there seems to be a bug if you feed a Tx process a table whose number of lines does not match the number of channels Tx.  This will result in weird errors funny will disappear only after doing a hard reset of the units.  So, just something to take note of.

  I hope this information will help others and this message can be marked as resolved.

• BUG? Out of multi channel analog Flips which channel it sends

  I a program that channels acquires 4 analog inputs, 2 analog output channels to send and acquires 2 input channels of the counter (on a separate card)

  My problem is that the analog output flips which channel it outputs. I built a table and my waveform desired ao0 at the top of the table build entry, then I drag the table of construction down to make entry as a second entry and I plug my second wave this entry. I noticed strange things on the scope. The program worked correctly, but repeatbly.

  The analog output channels the following steps

  channel 0 is sent to a level of zero, then for 1 data point a level 5. It comes to trigger a signal generator to the output of a wave of fishing 1 Hz, 1Vpp, 2cyc

  1 channel is sent with a square wave to trigger a camera to take a picture for each pulse.

  Step 1: Open SLOSHTABLEV4.vi

  Step 2: run.

  Note: the channel impulse is sent the trigger generator waveform causing the waveform to generate each pulse
  the trigger channel ends as high. to 5 volts.
  Step 3: Run simpleao.vi and set both channels to zero

  Step 4: See Re running SLOSHTABLEV4.vi that flips out what channel it is sent!

  There are three forms of production,

  the right one
  one where the waveform relaxation is camerapulse
  one where the waveform trigger is activated from the beginning.

  The solution was to update the drivers. Ugh!

• AI trigger and measure multi channels

  Hi all

  I have a simple problem (using USB-6259).

  can repeat the measurement trigger of AI and measure multi channels, but not both at the same time.

  -DAQmxCreateAIVoltageChan(hd, "DEV1/ai0",...)                    define the ai0 as the trigger channel

  -DAQmxCfgSampClkTiming

  -DAQmxCfgAnlgEdgeRefTrig

  -DAQmxStartTask

  -DAQmxReadAnalogF64 (hd, "DEV / ai0:3 ', / / I want to measure more channels"ai0:3"not just"ai0")

  Thank you

  Hassan

  Hi Hassan,.

  If you use an analog trigger with several analog channels, you will need to use the APFI0 input as source of relaxation. See this KB: Why do I get error-200264 when running analog reference trigger? All you need to do is to connect your analog signal online 0 to APFI0 (Paperback 20 in your case) and set the source of relaxation at APFI0.

  The reason is that you don't have that an NOC on Board (series E or M) and she's going to have to switch between the different lines (see this KB: modes of sampling). This parameter collides with the idea of a trigger analog reference on a specific line (constant sampling of data in a ring buffer up to what a condition is met). The APFI0 line, however, has its own CDA. Therefore, it can run simultaneously.

  However, please note that the ADC is fast but has lower resolution to HAVE it sampling ADC. See these KBs: series E and M series Analog Input Trigger resolution, be aware of a possible error between the analog trigger threshold and the value of the first sample

  Hope this clarified the issue.

  Best regards

  Peter

• Simultaneous multi-channel Imaging NI PCI-1422 or 1424?

  We have an IMAQ 1408. We want to make simultaneous multi-channel imagery. However, 1408 has only 1 A/D converter, it cannot acquire multiple channels simultaneously. We are looking for possible upgrade.

  The NI PCI-1422 or 1424 seem to upgrade products of 1408. Can someone tell us if they can do simultaneous multi-channel Imaging?

  Sorry if this isn't the right forum for me to post this question. But I called the customer service OR. The guy doesn't really know acquisition cards. I think that there are more experts here.

  If you have analog signals, it is a little more difficult.  NEITHER ensures more hardware to read signals from analog cameras.  I don't remember all of their equipment, be capable of more of an analog input signal simultaneously.  They always alternate between the signals, a reading at the same time frame.

  Your best bet would be to get an analogue to digital converter which converts the formats I've mentioned.  You must make sure it is compatible (uncompressed, industry standard, etc.).

  Bruce

• Imaging multi channels using the acquisition card OR

  We have a 1408 IMAQ being controlled by LabVIEW 8.0.

  We want to install multi-channel of imagery. All the channels work individually. However, when I was trying to show two channels simultaneously, single channel works and I got the following error message:

  Error 1074397150 has occurred to IMAQ enter Setup.vi

  Possible reasons:

  NOR-IMAQ: A timeout error occurred while you wait for the specified event. If you expect a picture, make sure all the video data is acquired during the period. If you wait for a signal, check that the assertion of signal occurs within the period.

  Sometimes I get a different error message asking me to assign different buffers to both channels. I understand that IMAQ 1408 has only analog digital (ADC) converter to digitize the incoming video. It may acquire up to four different cameras, but only of a camera at a time.

  I don't mind do frame rate in half. I think to show only one channel at a time and do the two channels alternantly. But I need to know how config routes to get there.

  I've attached an example that should work.  I could not test it because I don't have the equipment, so it might need some settings.  I would test it with one channel by setting the channel # 1.  Once it works, define channels # 2.  I set the display to use snapshot mode so the same image can be used for all screens.

  The only reason that I can think of that would make multi-channel acquisition fail when single channel works is the lack of synchronization between signals.  The start of frame signal must be the same for all channels.

  Bruce

• Cannot get DTS/multi channel audio via HDMI

  Hello
  I'm trying to connect my VAIO SVT15112CXS to my Bravia HDTV via HDMI to get multi-channel audio (DTS/DD) from my Bravia HT (connected to the TV via optical) with no luck at all.

  I have the same setup for PS3 works well, is it cable or equipment.

  I have already updated all the drivers.

  When the TV is not connected I don't get an Audio HDMI option in the playback devices (I checked to show disconnected devices / disabled) and when it is connected I do not get an option to change the configuration of stereo speaker.

  This way I get only Stereo sound.

  I tried passthough HDMI via ffdshow config (installed K-Lite codec pack) and there is no sound in this way.

  Is there a solution? something escapes me?

  Thanks to all in advance,

  Thanks for your time and your response.

  I got it actually work! updated drivers audio and video (not Sony ones sugested, but later of Intel and Realtek) and now I have everything works as it should.

  The only minor problem is that Vaio Care now wants me to go back to the previous version of the driver, but I'll just ignore it.

  Everyone, try this if you experience this problem.

• Multi-channel acquisition - simultaneous Acquisition of sampling 1 & 2-channel single sample in a task

  I am able to get a multichannel simultaneous sampling on my acquisition of data (USB-6363) without problem. But what I want to do is make multi-channel acquisition in a single task where sampling requirements are different for each channel. For example, I want I want to acquire a total of 1000 samples on 3 channels in a single task with DAQmx as follows the characteristics of sample:

  • AI0: Analog Wfm 1Chan NSamp (998 samples)
  • AI1 + ai2: 1 d analog NChan DBL 1Samp (1 + 1 sample/channel)

  I know I could do just a regular multiple sampling multi-channel acquisition through all three channels then average down from channels 1 + 2, but I don't have that several samples to spare. AI0 is a bandwidth hog in my application and consumes all the samples of data acquisition (2. MECH / s), but I can save a few samples to make analog measurements further (for example, temperature, pressure).

  Ai0 takes place also permanently so additional analog measures on ai1 + ai2 need to be included in the same task.

  I don't know how to go on this matter or if it is still possible. Any ideas or thoughts would be greatly appreciated.

  Currently I use a second DAQ to read these additional channels at a lower rate but I need to pass a single data acquisition.

  How should continuous ai0 really be?  You of course can enjoy on ai0, and one of the other entries at the same time, then there would be some gap in your data.  In addition, if you want to go to the full 2 MHz, you may sample ai1 ai2 twice in order to allow entry to set (the maximum specified multi-channel rate is only 1 MHz due to compaction of the constraints on the MUX I believe).

  DAQmx sort of you lets set something up like that, if you "cheat" it by configuring each sample as a single channel in your task (see an example similar here).  If your 998 + 1 + 1 (or 996 + 2 + 2) becomes a task of channel 1000 (takes a bit more memory, but should still be feasible).

  I would consider a 2nd DAQ card a better option if ai0 really needs to be continuous.  You can go with a (9174 or 9178) cDAQ chassis a 9223 (only 1 MHz if) for quick entry and your choice of module for the slower entries.  On the cDAQ chassis a module can run a separate task of AI from other modules (up to 3 tasks HAVE by chassis) at different speeds.

  Best regards

• I'm trying to export multi-channel audio as apple pro res 422 HQ, but the tracks are all coming full joint rather than separately. I've implemented the multi Channel sequence already. What I am doing wrong?

  I'm trying to export multi-channel audio as apple pro res 422 HQ, but the tracks are all coming full joint rather than separately. I've implemented the multi Channel sequence already. What I am doing wrong?

  All 4 titles are coming as complete blends not divisions. I guess that's a problem with the entrenchment of the channels, but can't see how to fix. Andy

  Is what would you say to my quick thought without following through all the processes after the fact, the sequence settings? My thought is that the sequence settings must be multichannel as you show, but each Adaptive track, so this channel map is routed at your leisure. If this is not the case, already, it would create a new sequence with these settings.

  I try to upload the photo

  

• multi channels data acquisition, a single frequency, counter a pulse, two voltage inputs, a power meter (by USB) and an analog output spontaneous and recording

  Hello

  I have a power meter which provide the USB driver and a Labview program to get the data and NI USB-6221. The project I am currently working on the needs of:

  1 acquire two signals (inputs of simple tension), pressure frequency KHz

  2. acquire a flow signal, the output signal is 0 to 5V pulse, each pulse means 0.4 ml volume. So I use a voltage inflows to count impulses in certain period of time (in this case, 1 S) for water flow. ; KHz sampling frequency and the 1 Hz update rate

  3. acquire a signal of engine speed. The output signal is pulse square wave whose frequency is related to the speed. I use a REIT port to measure the frequency. Sampling rate: Auto

  4 give output voltage sine or square wave, I use AO do that.output rate: Auto

  5 acquiring by VISA electricity meter data.  Data update rate: every 50ms

  Currently, all the 5 tasks work well separately. But when I put them together, some signals are beginning to hang, for example, pressure signals sometimes give nothing.

  Another problem is the data record. I programmed the VI in such a way that whenever I press the button 'save start', he begins to record data and save them in a .cvs file. For some reason, I always get only the data in the first table. Coult someone help me? I download my code as follows

  Hello

  What I meant by open, write, close.  For any type of file you are using.

  Open the file, which produces a reference, then put the mention in a registry to offset.

  Write data, using the function write (for this type of file) and the reference.

  When you are finished, close the file reference.

  Writing in the spreadsheet opens, written, close all at once.  It is very good for this type of application.

  ***

  The issue of the loop is more general.  I would like to say first of all, I want to say that since each loop works on its own, it is own VI, and that this program has put all this into a single VI, which has a method to solve the problem is to disable all the loops and allow them one at a time to see if there is a culprit responsible for.

  Using multiple loops executes the code at the same time, and some loops would be cycle faster than others, especially if some of them are loops just as they are.

  Communication between the loops is a test to the address if necessary.

  Running all these signals through different loops DAQ must also be examined.  Don't know what questions are for read and write somewhat randomly in the channels.

• FFT waveform recorded

  Hi all

  I am fairly new to LabView and data acquisition. Sorry to bother you. I have a question:

  "I recorded a waveform distorted by using digital oscilloscope. The format of the file is .bmp i.e. photo brush. I want to perform the FFT of this waveform analysis. How can I do in Labview? I already have the magnitude spectrum using the FFT of the oscilloscope mode, but I need to get the spectrum in phase as well so that I get the angle of phase for each of the harmonics. Would you be very kind to guide me in this regard? »

  Thanking in anticipation.

  Best regards

  Hernu

  
  

• Generation of weather in TDMS for measures of multi channels channel

  Hello world

  I have to write an application with five measures will at the same time... then it must be saved in TDMS each channel being its own channel of time just after she... IE sequence of the canal as below

  Channel group

  Measurement1

  (EDT) 1

  GCA2

  TIME2

  Measurement3

  Time3

  Measurement4

  Years.4

  Approvisionnement5

  Neuve5

  Each time channel should have "dt" for its number of measure...

  So far, I m succesfull in the measuring channel recording only all the... But I have no idea how design for each measurement time line...

  I tried to get the time I receive the data using functions as below

  GetSystemDate (month & day, &year);)
  GetSystemTime (& hours, minutes & seconds);
  sprintf (timeStr, ' %d/%d/%d % 02d: % 02d: % 02d ", day, month, year)
  hours, minutes, seconds);

  This will generate the channels of chain of time... but my requirement is of data type ' Date/Time' used on larger scale of the axis in tiara...

  Any help

  Thank you

  HS

  HS,

  There are two ways to store calendar for a channel information in a PDM file.

  You can only use the first method if timing information is regular (spaced), which means that it can be described with the only values t0 and dt.  This method translates a single channel in tiara which contains data values and stores the calendar as properties on the channel information.  Note that in this case DIAdem will treat time as relative values with no basis of absolute time values. The properties you must set on the channel are:

  (1) wf_start_offset (mandatory), the type is TDMS_Double, contains the time value t0 of the first data point of some units that you use and can just be 0 if your t0 value has no meaning other than as a reference for all other values of time in this channel point

  (2) wf_increment (required), type is TDMS_Double, contains the dt in whatever units you use

  (3) wf_samples (mandatory), the type is TDMS_Int32, contains the number of samples in the waveform

  (4) wf_xname (Optional), type is TDMS_String, contains the name associated with the x-axis of time and will be used by the tiara to label the x-axis in tracing this waveform

  (5) wf_xunit_string (optional), type is TDMS_String, contains a string that describes the x-axis of time units and will be used by the tiara to label the x-axis when tracing of this waveform

  You can set the properties above using the TDMS_SetChannelProperty function.

  You can use the second method for regular or irregular (not also spaced) timing information.  This method translates a channel with your data values and a separate second channel which contains the absolute timestamp values. From your original post, more like what you want.  In addition to your data channel, you must create a channel of timestamp.  Call TDMS_AddChannel with a data type of TDMS_Timestamp to create your channel of timestamp.  Call TDMS_AppendDataValues with the values of type CVIAbsoluteTime to write the Timestamp values in this channel.  You can create individual type timestamp values CVIAbsoluteTime by calling the functions of absolute time in the ICB Utility Library, such as GetCurrentCVIAbsoluteTime and CVIAbsoluteTimeFromLocalCalendar.

  I hope this helps.

  -Jeff

  NEITHER

• FPGA target host DMA FIFO multi-channel

  Hi people,

  I have a little trouble to collect my FPGA application data. The control of my FPGA application loop is running and read data from set point between a host and target FIFO to a period of 50 uSec. I run a separate loop to write data collected form two channels in a target of FIFO host over a period of 1000 uSec. I'm taking the data from both channels and its reading on the host in bundles of 500 data samples. The first problem I have is that my method of reading times unless I put my data acquisition loop to run at a much slower pace. My FIFO depth host side is 60000, almost as large as the total number of data samples that I expect to collect in total.

  I have another problem when trying to write the data to a table. Even if my method of reading does not expire, I don't think that will record the first beam of data that are read. I've initialized an empty table outside my acquistion of the side loop host and used the table VI build to take the current data set and add it at the end of this table. I then store in a shift register and pass it in the next iteration where I try to join the new data set to the old and so on. I expected to get a table with all the data, but as I said I'm only collecting the first set of 500. I wonder if my program structure is correct. Any help anyone could offer would be greatly appreciated. I have attached a few pictures of my reference request. Thank you.

  Hi Daniel,.

  Thank you for your response. I think I found a solution to the problems that I had. Looks like it was a combination of a couple things. First, the data acquisition loop was running not until the movement was already over since I plugged the condition to stop the loop of writing deposit directly on the data read loop. This problem has been fixed by creating a shared variable for the stop condition and it wiring to two loops independently. This explains why I got only the first set of data, as it was stored in the FIFO until the end of the movement. However, the FIFO of feedback was still time. Before attaching the stop condition error, I placed a probe on the "items remaining" wire of the read method and concluded that there was only 1023 elements (the depth of the FIFO on the side FPGA) even if I set the FIFO depth host side to 60000. "» I realized it was originally due to the Read method not called for the first time until the end of the movement. Although the problem of break for most fixed condition this problem given that the Read method was now called during the movement, I decided to take a preventive measure and calling the 'Start' before the movement FIFO method is started just to make sure that the memory of PEP on the side host is available immediately.

  So yes, it turns badly I put sync settings have been well after all. Good call on the reversal of the order on the Array function to build. Oh, and I also had to move the waveform diagram to until the table is built so that it is not Replot the old data on top of all the new data it receives. On the same note, I moved to the indicator in table at the end outside of the loop of reading. Thanks again for your help.

  Kind regards

  John has