Access-list command not supported in the 2.2 FWSM (1)

Similar Questions

• WebVPN - error: access method is not supported for the capture of WebVPN

  I'm watching a capture of webvpn on the SAA. I start the capture:

  test type webvpn user capture (entering a valid user name)

  Then I connect to the ASA to try to see track with "Using a browser to capture displayed data" as described in the setup guide.

  https:// / admin/capture/test/OCAP

  After login, I get this message in the browser:

  "Error: access method is not supported for WebVPN capture."

  If I stop the capture (capture test) before you try to connect, the error in the browser is:

  "404 not found".

  The/admin/capture/test/OCAP requested URL was not found on this server. "

  Any ideas greatly appreciated. Thank you!

  After some research, I finally found it

  DOC: Webvpn catches are recorded only in zip format

  
  

  CSCtg79320

  Symptom:

  WebVPN captures are only saved in zip format.

  Conditions:

  According to the following doc:

  http://www.Cisco.com/en/us/docs/security/ASA/asa82/configuration/guide/WebVPN.html#wp1153077

  WebVPN captures can be recovered in the pcap format using the browser, which is incorrect. The document must be corrected.

  Workaround solution:

  N/A

  Thank you for your time and cooperation

  Portu.

  In case you have any other questions please note all useful messages and mark this question as answered

• vmrun return "this operation is not supported with the current permit.

  Hello

  I just installed the 5.1 esxi and I have 2 vm windows works well.

  I use the vSphere client to manage the hypervisor.

  I have not installed vCenter stuff, so it is just bare hypervisor os.

  When I ran the following:

  «vmrun t h 10.10.0.9:443 u vpxuser Pei xxx list esx»

  He returns with "this operation is not supported with the current permit.

  In fact, I have installed esxi5 on hypervisor licensing, do not know why I get this error message.

  Access the esxi5 through the sphere client works very well (I could create vm, take snapshots, etc.).

  Please let me know if I missed any steps. Thank you

  -antony

  Welcome to the community,

  with the free license of the hypervisor, access to vSphere API is restricted, which is most likely causing this issue. To unlock the API, you must have a paid license. Unless your host has already exceeded the 60-day evaluation period, you could try to revisit the evaluation mode to see if the command works as expected.

  André

• File compressed using a codec that is not supported by the player

  I use Director of windows. I can't import audio my cd or i tunes = reason "file compressed using a codec that is not supported by the player", how to fix this? What are the options?

  Thanks for your help.

  Hello

  To check the file type, follow the steps below:

  (a) access the location where the file is stored

  (b) right click on the file

  (c) click Properties in the drop-down list

  (d) under the general tab check the listed file type.

  File types supported by Windows Media Player 12 and Windows Media Center

  http://Windows.Microsoft.com/en-us/Windows-Vista/file-types-supported-by-Windows-Media-Center

  For more information about iTunes contact Apple support in the below given link.

  http://www.Apple.com/support/iTunes/

  Windows Media Player cannot play the file. The player might not support the file type or does not support the codec used to compress the file. You may encounter this error message for the following reasons:

  1. the file type is supported by the drive, but the file was compressed by using a codec that is not supported by the player.

  2. the file might have been encoded with a codec that is not supported by Windows Media Player. If this is the case, Windows Media Player cannot play the file.

  Hope the helps of information. Please post back and we do know.

• Ipv6 access list does not apply autonomous Aironet 3602I-E

  As you can see in the attached config I configured two SSID (2G & 5 G) for a third (2G only) SSID and PEAP WPA2-Ent on the vlan 2 for 'poor team access as guest '.

  Basically I forced the Dot11Radio0.2 interface in the Group of deck 1 to get all three SSIDS on vlan 1 (since I want just a quick way and dirty to allow its customers access to the internet, without having to configure a vlan separate everywhere).

  The guest SSID (XX COMMENTS) allows tkip in addition to BSE and uses a PSK rather than PEAP. Access lists configured on Dot11Radio0.2 IPv4 allows clients connected to this SSID get an IP by DHCP, use the DNS servers on the local network and access the internet. All other traffic for the local network is blocked by access lists guest_ingress and guest_egress.

  This all works very well, ipv4 is blocked for guests invited as expected. However, ipv6 is something different. For some reason, the ipv6 access list is completely ignored.

  Because I don't need ipv6 for guest access, I thought that I have completely block and do with it. As you can see I have this set:

  interface Dot11Radio0.2
  guest_ingress6 filter IPv6 traffic in
  guest_egress6 filter IPv6 traffic on

  and these ipv6 access lists have a rule of "refuse a whole" only. Yet, the XX COMMENTS SSID connected client gets an ipv6 address of the server on the LAN DHCP6 and has full connectivity. For ipv4, that I had to explicitly allow DHCP packets to the client not even get an IP, so the ipv6 access lists are not clearly applied.

  No matter if I move the access interface Dot11Radio0 instead lists, they don't do anything. I thought that maybe I should add a "enable ipv6" on the Dot11Radio0.2 interface (even if ipv6 traffic was very good, even where it shouldn't), but when I set "enable ipv6" Dot11Radio0 or Dot11Radio0.2 the radio goes into a sort of infinite loop of reset:

  000261: Sep 23 2016 22:32:50.512 it IS: % DOT11-5-EXPECTED_RADIO_RESET: restart Radio Dot11Radio0 interface due to the reset of the interface
  000262: Sep 23 2016 22:32:50.516 it IS: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to down
  000263: Sep 23 2016 22:32:50.524 it IS: % LINK-5-CHANGED: Interface Dot11Radio0, changed State to reset
  000264: Sep 23 2016 22:32:51.516 it IS: % LINEPROTO-5-UPDOWN: Line protocol on the Interface Dot11Radio0, state change downstairs
  000265: Sep 23 2016 22:32:51.560 it IS: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to
  000266: Sep 23 2016 22:32:51.568 it IS: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to down
  000267: Sep 23 2016 22:32:51.576 it IS: % LINK-5-CHANGED: Interface Dot11Radio0, changed State to reset
  000268: Sep 23 2016 22:32:52.608 it IS: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to
  000269: Sep 23 2016 22:32:53.608 it IS: % LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed State to
  000270: 22:32:53.608 Sep 23, 2016 it IS: % DOT11-5-EXPECTED_RADIO_RESET: restart Radio Dot11Radio0 interface due to the reset of the interface
  000271: Sep 23 2016 22:32:53.612 it IS: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to down
  etc.

  In addition, when creating a list like this ipv6 access:

  guest_egress6 IPv6 access list
  refuse an entire ipv6

  The other is automatically created:

  IPv6-guest_egress6 role-based access list
  refuse an entire ipv6

  A deletion also removes the other.

  What is happening with these ipv6 ACLs, why they are not blocking all traffic? Why do I get an acl "role-based" too? Is associated it with?

  Is there a another way to kill just any ipv6 on the SSID of COMMENTS XX traffic while leaving alone on others? That's all I need at this stage. If the ipv6 ACL do not work, perhaps this can be done (ab) using a service-policy or policy routing? I'm ready to creative solutions :)

  PS. I know this is not the recommended method to configure a guest SSID, but it should still work IMO.

  You have encountered a bug I discovered a few months ago (CSCva17063), in your case, the workaround is to apply the ACL on the physical rather than the void interface interface (because you want to completely block IPv6 in any case). I write (more) my conclusions regarding the traffic that refusal on autonomous APs in a blogpost, might be interesting for you to read as well.

  Remember that the access point used as a bridge between the wired infrastructure and wireless, not as a router. There's some IOS routing of commands (like the "enable IPv6" command you pointed out) , but these are not the characteristics that should be used or need to be enabled on an access point.

  Because the networks internal and customer spend somewhere else, I would perform filtering on this device instead. Also sub gi0.2 interface is missing from your configuration, so I do not think that access as a guest is currently working at all?

  Please rate helpful messages... :-)

• While the iPhone overseas requires a reactivation, which sometimes works, but more often does not work. At the beginning he said that my SIM card was not supported by the activation policy assigned by the activation server.

  iPhone 6

  Network: Verizon

  iOS 9.3.3

  Twice now, once in Costa Rica in April and, more recently, in Ireland, while that phone overseas warning reads as follows:

  "your iPhone could not be activated because the activation server is not reachable. Try to connect your phone to the iPhone to activate it, or try again in a few minutes. If the problem persists contact Apple Support to Apple.com/support. »

  or:

  "The SIM card that you have currently installed in the phone is a carrier that is not supported in the title of the activation policy that is currently assigned by the activation server. This isn't a problem with the hardware with the iPhone. Please insert another card from a supported carrier SIM or ask this iPhone be unlocked by your operator. Please contact Apple for more information. »

  My carrier is Verizon and I replaced the SIM card on my return from Costa Rica end of April despite the fact that the card is unlocked and good, in theory, for international travel,

  Before you activate the phone is locked and I can't access applications like camera, that, when I travel, I need over the phone.

  Apple says call Verizon. Verizon said, you guessed it, call Apple.

  When I return to the States, everything works fine. I thought that the replacement of a SIM card would do the trick, so you can imagine my dismay when the activation warning came after I took the phone off airplane mode after I landed in Dublin and the activation warning came new.

  What is going on?

  kennypg wrote:

  iPhone 6

  Network: Verizon

  iOS 9.3.3

  Twice now, once in Costa Rica in April and, more recently, in Ireland, while that phone overseas warning reads as follows:

  "your iPhone could not be activated because the activation server is not reachable. Try to connect your phone to the iPhone to activate it, or try again in a few minutes. If the problem persists contact Apple Support to Apple.com/support. »

  or:

  "The SIM card that you have currently installed in the phone is a carrier that is not supported in the title of the activation policy that is currently assigned by the activation server. This isn't a problem with the hardware with the iPhone. Please insert another card from a supported carrier SIM or ask this iPhone be unlocked by your operator. Please contact Apple for more information. »

  My carrier is Verizon and I replaced the SIM card on my return from Costa Rica end of April despite the fact that the card is unlocked and good, in theory, for international travel,

  Before you activate the phone is locked and I can't access applications like camera, that, when I travel, I need over the phone.

  Apple says call Verizon. Verizon said, you guessed it, call Apple.

  When I return to the States, everything works fine. I thought that the replacement of a SIM card would do the trick, so you can imagine my dismay when the activation warning came after I took the phone off airplane mode after I landed in Dublin and the activation warning came new.

  What is going on?

  I think it's a problem with Verizon.

  Our company is on AT & T - and our lawyer have travel all over the world, Africa, London, South East Asia and they have never complained to me than before.

• Firefox 3.6.3 is not supported by the Google Font API

  I have Firefox 3.6.3 on my Macbook, but is only detected as 3.0.1on this form. When I have the link to the Google fonts site, he said, "we're sorry, but your browser is not supported by the Google Font API. To browse the fonts in the fonts directory Google please switch to a browser more modern. "I have to use Safari to access the page.

  URL of affected sites

  http://code.Google.com/WebFonts

  Maybe this article will help you - sites say that Firefox is obsolete or incompatible, even if it's the latest version

• Calibration error SMU-4141 niDCpower version 1.8, "calibration function is not supported by the device."

  Dear Sir.

  Nice to meet you.

  When I run the SMU-4141 "Adjust voltage Leve.vi niDCPower Cal" calibration function niDCpower version 1.8.

  It shows an error "function of calibration is not supported by the device." (false cae)

  But if I run the calibration function SMU-4141 "niDCPower Cal Adjust voltage Measurement.vi", (real deal)

  It will work.

  See attachments.

  My equipment list:

  Windows XP SP3

  LabVIEW 2011

  niDMM 3.0.5

  niDCpower 1.8

  PXI-1073 case with 2 cards.

  SLOT2: SMU-4141

  slot6: PXI-4071

  Could someone tell me the solution?

  Hi Peter,.

  The calibration process indicates that the call of the function of voltage adjust NI - DCPower Cal calibrates both the output level of the device as well as the ability to measure of the device.  It is even for the Cal of NOR-DCPower function adjust a current measurement.

  You must perform a calibration automatic on the device prior to the initial audit of the device, before the adjustment process and before the final verification process.

  I'm not sure I understand your question very well.  Please let me know if I have not responded sufficiently.

• EtherCAT: "found a module not supported on the slave device"?

  Hello

  I have a CompactRIO system that uses of slave hunts EtherCAT (cRIO-9081 + cRIO-9144) when I tried to deploy my settings, I got this message:

  Found a module not supported on the device slave address 0: 32445 slot

  What does that mean? (I have several slaves Garland, but of course, I don't have that many slot machines!) The chassis that has been reported with a red exclamation point contains these modules:

  • NI9201
  
  
  • NI9203
  
  
  • NI9265
  
  
  • NI9421
  
  
  • NI9481

  Is one of them unsupported on EtherCAT? If so, is there a list of modules taken into charge/no supported somewhere?

  Thank you!

  Hey there,

  I think you'd find this knowledge base, http://digital.ni.com/public.nsf/allkb/CA3A1D2166A4591386257514007A0F9C?OpenDocument , useful. It would be better to check what version of DAQmx you use and check the readme associated for compatibility or verify this DeveloperZone, http://www.ni.com/white-paper/10462/en. I hope this helps.

• recovery disk will not load error message pc not supported by the system recovery disk.

  had a virus that has taken possession of my PC and wanted the money order to the for free, so I install the recovery disk and chosen in advance and restored the pc at the time, he removed the hold and the system worked very well for a few days. then the system kept to self-extinguish. tried loanding the recovery disc and gave me the message pc not supported by the recovery disc, and now when start received bios award phoenix instead of the hp logo.

  attempted to run antivirus software but before he could finish short scan the pc shuts off I tried in safe mode and the same situation. I downloaded several antivirus programs, but it would still be closed the pc. I tried to install the recovery disk, and it gave me an error message pc not supported by the system recovery disk. now when I start up instead of the blue screen with HP logo, I get a bios award phoenix and other information that I can't copy down it goes too fast. Since I couldn't get rid of the virus, he took to a pc using store, they have removed the virus and loading of operating system vista, problem is I had the word and excel. Now, I can not get my desktop to factory oem computer. I really need my word that I have all my passwords for the accounts listed, I saved them to analyze the drive, but now I have not any other readers like drive j. Any suggestion on how to solve the problem, so I can load the recovery disc.

  Thank you very much

  Frenchquarter, welcome to the forum.

  I suggest that you download and install OpenOffice.  It is FREE and is open to all documents created in MS Office.  If it doesn't, at least it costs you nothing to try.

  I used OpenOffice for years.  Believe me when I say that he will do everything that will make MS Office and in some cases, the better.  At least, you will have to use in the future and you'll be amazed to see how they can do it for FREE.

  Please click on "BRAVO", if I helped you and click on "Accept as Solution" If your problem is resolved.

• Debugging is not supported on the selected Blackberry Simulator

  I just installed the plug-in for Visual Studio. Installed simulators are Torch 9800 (v6.0.0.534), the Torch 9800 (v6.0.0.313), 9930 (v7.0.0.318), they all give me the same message. I have a simple HTML web page, set to debug, when you click on play, I get the message, "debugging is not supported on the selected Blackberry Simulator. Only the loading and the launch of WebWorks Applications currently available. Please select a different Simulator if you need.

  Any ideas?

  Adam

  I think that the debugger works with the simulators that have v5.0.x BONES.  All those you listed are 6.0 or more.

  Try a simulator to v5.0x.

  The visual studio plugin is removed in October I think.  The new test environment is the emulator of the ripple.

  http://ripple.tinyhippos.com/

• Question of access list for Cisco 1710 performing the 3DES VPN tunnel

  I have a question about the use of access lists in the configuration of a router Cisco 1710 that uses access lists to control traffic through the VPN tunnel.

  For example the following lines in a configuration on the remote router. My question is whether or not the traffic that matches the definition of list access-130 (something other than 192.168.100.0/24), cross the VPN tunnel or go directly to the Ethernet0 interface.

  My understanding is that traffic that matches the access list 120 would be encrypted and sent through the IPSec tunnel. If there was "ban" set out in the statements of 120 access-list, the traffic for those would be sent through the IPSec tunnel but not encrypted (if possible). And finally, given that the definition of crypto card reference only "adapt to 120", any traffic that matches 130 access list would be sent Ethernet0 but not associated with the card encryption and thus not sent through the IPSec tunnel. "

  Any input or assistance would be greatly appreciated.

  Map Test 11 ipsec-isakmp crypto

  ..

  match address 120

  Interface Ethernet0

  ..

  card crypto Test

  IP nat inside source overload map route sheep interface Ethernet0

  access-list 120 allow ip 192.168.100.0 0.0.0.255 10.10.0.0 0.0.255.255

  access-list 130 refuse ip 192.168.100.0 0.0.0.255 10.10.0.0 0.0.255.255

  access-list 130 allow ip 192.168.100.0 0.0.0.255 any

  sheep allowed 10 route map

  corresponds to the IP 130

  He would go through the interface e0 to the Internet in clear text without going above the tunnel

  Jean Marc

• SRM5.1 / midsize V7000 6.4.1.4 command not supported: [discoverArrays]

  Hi all

  Production site:

  IBM midsize V7000 and FW level: 6.4.1.4

  SRM worm: VMware-srm - 5.1.1 - 1082082

  SRA: IBMSVCSRA_v2.2.0.130422

  IP: 192.168.70.50

  vCenter 5.1 U1

  Recovery site:

  IBM midsize V7000 and FW level: 6.4.1.4

  SRM worm: VMware-srm - 5.1.1 - 1082082

  SRA: IBMSVCSRA_v2.2.0.130422

  IP: 192.168.70.60

  vCenter 5.1 U1

  When I try to add the table then this error has occurred

  SRA command 'discoverArrays' failed. Invalid ID Array.

  Refer to IBM SAN Volume Controller troubleshooting

  And the SRM journal is attached.

  But I see this part of the newspaper.

  Sorry for the bad English.

  --> < name > discoverArrays < / name >

  --> < OutputFile > C:\Windows\TEMP\vmware-SYSTEM\sra-output-12-119 < / OutputFile >

  --> < StatusFile > C:\Windows\TEMP\vmware-SYSTEM\sra-status-13-225 < / StatusFile >

  --> < LogLevel > verbose < / LogLevel >

  --> < LogDirectory > vCenter Site Recovery Manager\Logs\SRAs\IBMSVC C:\ProgramData\VMware\VMware < / LogDirectory >

  --> < connection >

  --> < login id 'primary' = >

  --> < address >

  --> < code address = 'spA' > 192.168.70.50:5989 < / address >

  --> < code address = "spB" > 192.168.70.60:5989 < / address >

  --> < / book >

  --> < username > * < / username >

  --> < password > * < / password >

  --> < / connection >

  --> < / connections >

  --> < / order >

  2013 06-20 T 14: 34:33.395 + 03:00 [02020 'SysCommandWin32' verbose opID = 258F28AC-0000001 has] from process: "C:\Program VMware vCenter Site Recovery Manager\external\perl-5.14.2\bin\perl.exe" "C:/Program Files/VMware/VMware vCenter Site Recovery Manager/storage/sra/IBMSVC/command.pl.

  2013 06-20 T 14: 34:33.395 + 03:00 [02020 'SraCommand' verbose opID = 258F28AC-0000001 has] reset SRA command timeout for '300' seconds in the future

  2013 06-20 T 14: 34:33.395 + 03:00 [02020 'SraCommand' verbose opID = 258F28AC-0000001 has] listening to updates to the file 'C:\Windows\TEMP\vmware-SYSTEM\sra-status-13-225 '.

  2013 06-20 T 14: 34:33.395 + 03:00 [02020 verbose "PropertyProvider" opID = 258F28AC-0000001 has] ASSIGN RecordOp: info.progress, dr.storage.StorageManager.createArrayManager1

  2013 06-20 T 14: 34:33.441 + 03:00 [02444 'DrTask' verbose opID = 258F28AC-0000001 has] created task VC 'com.vmware.vcDr.dr.storage.StorageManager.createArrayManager:task - 3901'

  2013 06-20 T 14: 34:34.065 + 03:00 [01496 info 'SraCommand' opID = 258F28AC-0000001 has] stdout of discoverArrays:

  -> discoverArrays

  -> By Haz 20 14:34:33.909: [Info] the execution Module [constant] Inatall path: [C:\Program VMware vCenter Site Recovery Manager\storage\sra\IBMSVC\]

  -> By Haz 20 14:34:33.909: name of SRA for the [constant] runtime [Info]: [IBM System Storage SAN Volume Controller adapter for VMware vCenter Site Recovery Manager] uuid: version [38295F72-F7D0-4A0F-B8D4-FF9821AB2675]: [2.2.0.130422]

  -> By Haz 20 14:34:34.19: file commandName for the runtime [SRARunner] [info]: [discoverArrays]

  -> By Haz 20 14:34:34.19: runtime [SRARunner] logLevel [verbose]: [comments]

  -> By Haz 20 14:34:34.34: Module enforcement [verbose] [SRARunner] output file: [C:\Windows\TEMP\vmware-SYSTEM\sra-output-12-119]

  --> 14:34:34.34 by Haz 20: [fatal] runtime [SRARunner] command not supported: [discoverArrays]

  ->

  2013 06-20 T 14: 34:34.065 + 03:00 [01496 error 'SraCommand' opID = 258F28AC-0000001 has] stderr of discoverArrays:

  -> com.ibm.cstl.hsg.sra.svc.SRAException: command unsupported: [discoverArrays]

  -> to the com.ibm.cstl.hsg.sra.svc.SRARunner.execute(SRARunner.java:100)

  -> to the com.ibm.cstl.hsg.sra.svc.SRARunner.main(SRARunner.java:173)

  ->

  2013 06-20 T 14: 34:34.065 + 03:00 [01496 "SraCommand" verbose opID = 258F28AC-0000001 has] Stopped listening to updates of file 'C:\Windows\TEMP\vmware-SYSTEM\sra-status-13-225 '.

  2013 06-20 T 14: 34:34.065 + 03:00 [01496 "SraCommand" verbose opID = 258F28AC-0000001 has] cancelling SRA command timeout

  2013 06-20 T 14: 34:34.065 + 03:00 [01496 info 'SraCommand' opID = 258F28AC-0000001 has] discoverArrays came out with exit code 0

  2013 06-20 T 14: 34:34.065 + 03:00 [01496 "SraCommand" verbose opID = 258F28AC-0000001 has] discoverArrays responded with:

  --> <? XML version = "1.0" encoding = "UTF-8"? >

  "--> < response xmlns ="http://www.vmware.com/srm/sra/v2">."

  --> < error code = "4" / >

  --> < / answer >

  I solved this problem.

  The problem was MRS. Server intalled on the regional settings of Windows Server 2008 R2.

  My locale of the server was Turkish, when I install MRS I changed to English and installed.

  Finally, I reinstall Windows Server 2008 R2 full English for the United States settings after installed SRM.

  It has been worked.

• Adobe flash plugin not supported in the e bike 2nd gen (xt1506)

  fix Adobe flash plugin not supported in the bike e 2nd gen (xt1506) please.

  Nothing for Mozilla to difficulty. The phone uses a quad-core processor, in which the discontinuous old Adobe Flash player 11.1.x does not support because he can't stand of the ARMv7 processor.

• SIM card is not supported in the activation

  I have a question about activating my iPhone with a different SIM card. I have an unlocked iPhone and I tried to use another (of another carrier) SIM card with it. However, the phone will not turn on and I got an error message indicating that the SIM card is not supported by the initial activation and it isn't a hardware problem. He advised me to call my carrier. So I called my operator and the customer support agent has confirmed that my iPhone is indeed open. Now I'm really confused as to why the other carrier's SIM card is not supported. All SIM cards I've tried with my current provider works with my iPhone. All other SIM cards from other telecommunications companies does not work (I tried 3 others).

  Then the phone is not unlocked. Have you asked an unlock of your carrier and they gave him? If Yes, do restore you the phone to factory with iTunes and receive a "congratulations, your phone is now unlocked" message? If this isn't the case, then the unlock code is not complete. You must restore the device with iTunes at the factory, not a backup. When you get the message "Congratulations", you can restore your backup.