Activation of SSH on N2000

Similar Questions

• Difference between Shell ESXi and active with SSH PuTTY?

  Hello

  We used to activate SSH and PuTTY to connect to 5.5 ESXi host.

  However, a consultant suggested allow ESXi Shell and access it via DCUI.

  Would just like to ask you what is the difference between these 2 methods of access?

  Thank you

  Accusing Shell of ESXi is available by using two different ways.

  (1) local access to the shell of ESXi is available turning and by using directly from DCUI (Alt + F1), safer, since it is connected locally

  (2) remove access to the shell of ESXi is available by activating SSH Shell and using the SSH Client such as PUTTY etc to access. Since it is remote access, security is a bit of a cause for concern.

  This is the reason, the suggestion to use locally DCUI is given.

• Active but cannot access SSH

  I activated the SSH on ESXi 5.1.0 host, but I can't access it. No open port 22 is visible via nmap unlike other hosts I can access. Is any other how to activate SSH? I can't restart the host in the moment.

  Hope that you enable ssh as mentioned below

  Enable SSH and ESXi ESXi 5.1 Shell host ~ VMware Arena

  -Assane

• Did you come out ssh and now cannot use ssh - this had to happen one day

  Pro2 OS6 v 6.4.0

  SSH

  I logged in ssh [email protected]

  No files were open, but before I "exit" the session that the unit did a stop/delayed. I had completely lost track of time.

  Now, I can't ssh in. I've disabled the ssh, rebooted, activated the ssh and tried again.

  It happens just to expire without asking for my password.

  Is there one solution other than a reset of the OS or the factory re - install?

  Thank you very much

  David

  I don't know if everybody looked at it but he came good again after a few days.

  I have no idea why he decided to ask for a password... but it works.

  David

• SSH...

  Hello

  I activated the ssh ver 1 to my router, and when I run the command "sh ip ssh" is the result:

  Active SSH - version 1.5

  Authentication timeout: 20 seconds; New authentication attempts: 5

  I now use "putty" to access the router. His request to connect as and password. My understanding is that password is the one I've settled on vty lines, is not? What should I use in the connection like? If anyone can help please? Thank you.

  You have configured the following on your VTY lines: input ssh transport

  You can also check your config with the example here: http://www.cisco.com/en/US/tech/tk583/tk617/technologies_tech_note09186a00800949e2.shtml

  I hope this helps.

  Steve

• Creating a Clone VM of model VM using SSH console error DiskLib_Check()

  Hi all

  I'm now using ESXi 3.5 u4 and I activated the SSH connection.

  in a PuTTY console, I run the following command:

  1. vmkfstools-i/vmfs/volumes/datastore1/WinXPProSP3vmxp00_ md3000i/vmfs/volumes/MD3000iVMFS/WinXPProSP3_vmxp01_

  to copy the virtual directory WinXPProSP3vmxp00_ in my SAN-VMFS, but then I got this error:

  * DiskLib Check() has failed for disc source the specified file is not a virtual disk (15). * _

  is there a best way to do without vCenter license?

  or just use ishall

  _CP - r

  / vmfs/volumes/datastore1/VM_Templates /& lt; SOURCE & gt;

  / vmfs/volumes/datastore1 /& lt; DESTINATION & gt; _

  Instead?

  Thank you.

  Kind regards

  AWT

  vmkfstools only work with the drive.

  The best solution is using VC.

  Converter also works very well.

  But if you use the copy of files (like cp) you MUST regenerate vMAC address (when you turn on the computer virtual don't say keep!).

  The virtual machine should be also customized (new name, new IP, new SID), but in any case.

  André

  * If you found this device or any other answer useful please consider awarding points for correct or helpful answers

• Impossible to download the package to the ASDM

  Hello team,

  I have an ongoing problem here. Initially when I bought the Cisco ASA 5505 other guys IT registered who on their own ID of ORC. Now that they have left the company and person have no contact with them.

  I activated the SSH and I am able to login via putty/tera term, but when I access my device IP that is https://192.168.35.1 it gives me an error which and the page does not load. After continued research, I found that it has no ASDM package in flash player. When I went to downloads on Cisco's Web site, he asked me the Cisco ID and I have created a new and attached the device S/N and the device was attached to my CCO login. When I download it after that, it shows that I don't have a "valid service contract.

  Is there a way I can download it?

  Or I'm sued for my life by my boss?

  Thank you

  Buxant

  You can try to look on some of the biggest Web retailer sites like CEP, but unfortunately I have no idea about the cost.  It can vary according to the statements of the feature and the level of support you are looking for.

• How can I disable telnet on AIR-AP1242AG-E-K9?

  I activated the SSH with user name and password, but I noticed that when I type a username he accepts, as I have to disable the telnet, while I am using SSH

  Configure these commands in your AP

  !

  block-telnet extended IP access list

  permit tcp any any telnet neq

  !

  line vty 0 4

  block telnet access class in

  !

  Ragards

• ASDM does not work in the external interface

  Hello

  I'm new to ASA. I have ASA 5510 and strives to enable ASDM access through the external interface. but is not working for me... not. I set up a public ip address on the external interface and activated the ssh and asdm. SSH works but asdm does not work. This is a test environment, so I have not yet set up an ACL.

  VPN-TEST # show version

  Cisco Adaptive Security Appliance Version 8.2 software (1)

  Version 6.2 Device Manager (1)

  Updated Wednesday, 5 May 09 22:45 by manufacturers

  System image file is "disk0: / asa821 - k8.bin.

  The configuration file to the startup was "startup-config '.

  VPN TEST up to 4 hours and 33 minutes

  Material: ASA5510, 1024 MB RAM, Pentium 4 Celeron 1600 MHz processor

  Internal ATA Compact Flash, 256 MB

  BIOS Flash Firmware Hub @ 0xffe00000, 1024 KB

  Hardware encryption device: edge Cisco ASA - 55 x 0 Accelerator (revision 0 x 0)

  Start firmware: CN1000-MC-BOOT - 2.00

  SSL/IKE firmware: CNLite-MC-Smls-PLUS - 2.03

  Microcode IPSec:-CNlite-MC-IPSECm-HAND - 2.04

  0: Ext: Ethernet0/0: the address is d0d0.fd1d.8758, irq 9

  1: Ext: Ethernet0/1: the address is d0d0.fd1d.8759, irq 9

  2: Ext: Ethernet0/2: the address is d0d0.fd1d.875a, irq 9

  3: Ext: Ethernet0/3: the address is d0d0.fd1d.875b, irq 9

  4: Ext: Management0/0: the address is d0d0.fd1d.8757, irq 11

  5: Int: not used: irq 11

  6: Int: not used: irq 5

  The devices allowed for this platform:

  The maximum physical Interfaces: unlimited

  VLAN maximum: 50

  Internal hosts: unlimited

  Failover: disabled

  VPN - A: enabled

  VPN-3DES-AES: enabled

  Security contexts: 0

  GTP/GPRS: disabled

  SSL VPN peers: 2

  The VPN peers total: 250

  Sharing license: disabled

  AnyConnect for Mobile: disabled

  AnyConnect for Linksys phone: disabled

  AnyConnect Essentials: disabled

  Assessment of Advanced endpoint: disabled

  Proxy sessions for the UC phone: 2

  Total number of Sessions of Proxy UC: 2

  Botnet traffic filter: disabled

  This platform includes a basic license.

  VPN-TEST # http see race

  Enable http server

  http 0.0.0.0 0.0.0.0 outdoors

  VPN-TEST # display running asdm

  ASDM image disk0: / asdm - 621.bin

  enable ASDM history

  Could someone please help me know what Miss me?

  Kind regards

  Praveen

  That's it, please add any combination of encryption by using the command "ssl encryption" algorithms, please add them in one line next to each other, and you can use '? ' to check available combinations.

  Kind regards

  Mohammad

• VMware Esx 5.1 close Script

  Hi guys.

  I wonder if someone could help me.

  We have several power outages here in South Africa and I am faced with having to close our servers regularly.

  I had all our windows servers stop automatically via our software UPS (Riellio)

  I tried to download the Vmware software from our support UPS page but they say that it won't work on the free version of Esx 5.1.

  In turn what I've done is to create a script that runs through Plink and I'm hoping to use it on another machine to windows as a shuhtdown script.

  Thus, when the windows box stops he will run the script and closed to turn the ESX I anime.

  I activated the SSH on the Esxi server and when I run the stop script it stops the server very well but I read that the server must be in Maintenance mode during extinction.

  I want to just make sure that it stops the Esx server with elegance.

  The script is below:

  Any help would be appreciated.

  Text of script as follows:

  Plink - ssh [email protected] - pw mypassword poweroff d 10

  Plink - ssh [email protected] - pw mypassword poweroff d 10

  Hello

  While studying the possibility to do it via the device, you can change your order to do the following:

  Plink - ssh [email protected] - pw MyPassword "esxcli system set to true maintenanceMode EI; . poweroff d 10 "

  in this way the host will enter first mode of maintenance and the next order via; will be stopped.

• VMware Vsphere Client "Error unexpected envio" no puedo connect

  Hola a todos,

  I have an al servidor me conecto through VMware Vsphere Client. Hoy al try connect me salta este error:

  vSphere client could not connect to xx.xx.xx.xx a unknown connection error has occurred. (The client may not send a request to the server. (Se ha terminado la conexión: erreur inesperado de envío))

  If hago UN ping an IP the well esta responde y las maquinas office alojadas in el servidor estan well running. Intento connect desde a Windows 8 y otras veces conectado has no sin problemas, pero ahora no puedo. ¿Algun Consejo? MUCHAS gracias.

  Hola,

  El activated HE SSH, he accedido via consoled y ejecutado he:

  services.sh reboot

  Y el problema is ha solved. Este comando're valido para VMWare ESXi 4.x

  A greeting

• P2v Converter Linux

  Using Vm Converter 5.0 to P2V a linux server. But get a read only file system on VmLinux file after conversion. I was wondering if anyone knows an m.o. to convert physical Linux vmware using converter 5. I looked, but everything I've found using Converter 4.0 + using Boot CD. For converter 5.0 can I us still need to boot CD or activation of SSH on linux... etc. If anyone can help with a step by step procedure really appreciated.

  Thank you

  Hello

  Option 1

  (1) save the file/etc/fstab

  (2) try to re-create the file/etc/fstab without additional options for.

  LABEL = / / ext3 defaults 0 0

  Try restarting the server.

  Option 2

  Edit the /etc/rc.local

  and add the line at the end

  Mount o remount, rw-/ dev/sda2.

  Let me know if you still have questions

  See you soon

• HOW TO TRANSFER FILES FROM WINDOWS MACHINE FOR ESXI

  Hi I want to transfer files from windows to ESXi 3.5 machine, I have a tool winscp. but I am unable to connect via winscp. I activated the SSH too. Sugest me how to transfer files to ESXi

  some links of usful for the same query

  http://www.bhcblog.com/2008/10/18/HOWTO-transfer-files-and-VMS-to-ESXi-Server/

• ESXi console - how to get there?

  If I do not have a KVM - how do to the ESXi 5 console, set a password?

  I activated the SSH and also the "shell of ESXi" (what the hell is that?), but when I PuTTY the server, I just... get a bash as thin shell.

  I need to access the current remote host console - how can I do?

  Ted

  PS - just for now, I just need to set a password for the host. If there is a way to define in vCenter, please share!

  I need to access the current remote host console - how can I do?

  Assuming that mean you the yellow-grey console, type dcui on the command prompt and press the Enter key.

  ... and also the "shell of ESXi.

  It is the command-line (Tech Support Mode) you get by pressing ALT - F1 on the console.

  André

• vSphere cannot connect after time on the host change

  I am a relative noob when it comes to virtualization.  I did a lot of research for the response, but can't find it.  Maybe you guys can help.

  Connected to the host (VMWare vSphere for ESXi 4.0) management console, I changed the time on the host because he was distant.  After that, the vSphere console has become very slow, and when I clicked on another tab it has expired.

  I closed vSphere and tried to reconnect and now I have a message that says:

  vSphere could not connect with the server vCenter Server "[host IP address] '.

  Details: A connection failure has occurred (unable to connect to the remote server)

  I went directly to the physical console machine and press F2 to enter the system setup.  I restarted the management agent.  I can ping the IP address.  I can not connect via puTTy, but I do not think that I never activated the SSH access.

  Has anyone ever encountered this?  What should I do?  I can't restart the host right now because the production servers are running on the VMWare.  If I have to restart later, what is the correct procedure for this? (close the BONES of the VM, and then restart the host?)

  I had this happen before. I was unable to restart the services or navigate from the console. I waited until hours off-peak and connected directly in the less critical guest OS and stop them. I had to stop several before I could get access again vcenter. Once I had access i vMotioned the rest of the guests to other hosts and restarted the ESXi host. It's a risk, because if you cannot close machines you have to powercycle. You seem to have access, so you can be able to stop them from the CLI on the host.