Add LaserJet 1525nw to the wireless network

Similar Questions

• HP LaserJet Pro CM1415fnw color multifunction printer - cannot FIND the WIRELESS NETWORKS

  PRINTER: HP LaserJet Pro CM1415fnw color multifunction printer

  OS: Windows 7

  OWNER: More than 2 years without any problem

  LOCATION/SET-UP: To my personal residence. All-in-one router through the cable company.

  QUESTION: Suddenly, printer cannot find wireless networks. Nothing has changed recently in my service provider or equipment. I know that the router and the internet is not the problem because our 2 smart phones and three laptops still not connect. I triend manually configure the network using the SSID and key phrases, but still nothing.

  Help!

  I would like to perform a hard reset by removing the power of the whole machienethrough the power cord for 30 seconds. Depending on whether I have would reconnect the printer to the wireless network and set a static IP address.

  -Spencer

• Impossible to manually add the wireless network

  I need to manually add a wireless network to the laptop. When I click on add in the wireless connection properties window, however there is no pop-up window. If I try on a similar laptop windows wireless network properties appears. The Wireless Auto-Configuration service is started. How can I get the wireless network properties window?

  I was finally able to solve this problem and I posted the results on another forum, I used for this purpose.  Here is the text exactly as I posted on the other forum.  It answers some of your questions.
  Regarding other software that manages the wireless card, Yes, there are (Atheros), he was not managing the adapter (off a long time ago), however, to be sure, I removed it to run in the registry.

  Here is the text of how I solved the problem, I mentioned.  If you have more questions, feel free to post them.

  *****

  I am just posting this here because I could solve the problem and not able to find a reliable source on the internet on a fix for this and for a problem that is the result of my attempts to fix it.

  This is the situation and my landline.

  I was getting this error message

  "Impossible to migrate dependent packages.

  After trying to install a pacakage KB. It did not matter that one but they have been associated with the Wireless settings.

  I continued to try to install the newer packages.
  KB893357
  KB917021
  KB918997

  Each gave me the same message

  "Impossible to migrate dependent packages.

  I read online that I install KB937143 (update IE7) could help.

  I did this and still got the same message on dependent modules.
  I also had another problem occur.
  In the section my network places properties connection wireless adapters, whenever I clicked the Add button / PROPERTIES without window appears to allow me to change the settings, however, I was able to remove items from the preferred networks window.

  My Automatic Configuration Service wireless is running and took Windows to configure my wireless settings.

  I downloaded the updates for my driver Wlan (WiFiHP 500) and I still had the same problems.

  I restarted KB918997 using the/log option and read the log file. This is the last important lines:

  33.849: MigrateHotfix: hotfix migration KB937143
  34.129: migrating QFE KB937143 with command line: update.exe z q - B: sp2qfe
  36.783: failed 1603 Update.exe.
  36.793: MigrateHotfixes: KB937143 Migration failed
  36.793: DoInstallation: Migration failed
  36.933: failed to migrate dependent packages.
  39.597: message displayed to the user: cannot migrate dependent packages.

  I then uninstalled the KB937143 package and reinstalled KB918997 update with the newspaper of Pétion and he went along. I also tested the buttons add and PROPERTIES in the window of Favorites and those networks worked too.

  I checked the logfile KB918997 and he showed this:
  42.311: MigrateHotfix: hotfix migration KB932168 have
  42.511: migrating QFE KB932168 have with the command line: update.exe z q - B: sp2qfe
  88.768: MigrateHotfix: Hotfix KB932168 successfully migrated
  88.768: MigrateHotfixes: return code: 3010
  88.928: DoInstallation: Migration succeeded

  As a side note, I restarted the laptop frequently just to be sure.

  So, really, the option of running with the Ko log file helped me diagnose the problem.

• HP Laserjet 200 M276 Color MFP: HP Laserjer 200 color than MFP M276 found on the wireless network

  Printer is connected to the wireless network, but cannot be seen by the computers on this network.

  The printer has been installed on my home network for 6 months and works well.  Now it is found on the network.  Power cycle the printer, and he started to work for one night.

  The day after the printer is found on the network by PC, running Windows or Mac 8.1 on the network (under Leopard through Yosemite.

  Reset printer settings by default, in the wireless network data and verified that it is on the network (wireless diagnostics confirm the network name, config, port and switch Diagnostics).  Still cannot be found on the wireless network.  I know that it is on the network, because it can access internet functions.

  Repeated configuration via USB for settings wireless program.  Receive error message indicating the wireless settings have been communicated successfully to the printer, but the printer is not found on the wireless network.

  Not cool.  Looks like I have yet another broken HP printer.  I don't know the process.  I called the warranty and they are sending me a refurb printer.

  Returned to the HP after 10 years.  Looks like it was a mistake.

  Hello

  Try restarting your router by unpluggin power for a while, let him 3 minutes to start and restart the printer.

  Click the icon on the printer wireless - what is the listed IP address?

  Can happen that the intellectual property of the Explorer of your computer?

  You can see any difference after the reboot of the router?

• How can I add a printer to my wireless network

  How can I add a printer to my wireless network

  John

  I assume that you have a wireless printer. If so, the software is different from each manufacturer, but it is similar to this. Before starting the installation, make sure that you have a USB cable at your fingertips and you know your network name (SSID) and wireless key. Install the software and follow the prompts to set up the connection Wireless for the first time. Once it has been set up you can unplug the USB cable.

  The USB cable is not required on subsequent computers, simply install the software and follow the prompts on the screen of an additional computer (or similar wording). You may need to enter an SSID and Wi - Fi key, after which the printer must be accounted for.

• Unable to connect to the wireless network, error message "Windows could not finish repairing the problem because it is impossible to perform the following action. Renewal of your IP address.

  Original title: Unable to connect to the wireless network

  Unable to connect to the network wireless Toshiba Satellite A105 PC running Windows 7.  "Windows could not finish repairing the problem because it is impossible to perform the following action. Renewal of your IP address.  Works with Windows XP SP2, IE 8.00.6001.18702 file, I think that Version 3.  It has been installed on a disk provided by Microsoft after that old installation became corrupt (in the sense of Microsoft technical support.)  Before that, wireless network worked well.   (So unable to connect to the Internet for updates.)   Have tried to change the other settings and different messages acquired when it SHOWS that I am connected but cannot connect because of something to do with the certificate.  I don't remember what I did to try to solve this problem in the last days.

  I should add that I have tried the solutions of the previous forum on this topic, and none worked.

  Hi Marilynnla,

  Sorry to hear about the bad experience you encounter. Lets see if the network problem can somehow be archived.

  Read this article and follow the steps. Lets see if it helps in any way.

  How to troubleshoot wireless network connections in Windows XP Service Pack 2 (Works for Windows XP SP3 as well)

• Router E4200, cannot secure the wireless network

  When my E4200 wireless network appears on a discovery list of wireless networks, there a padlock beside him in devices (like my Xbox and iPhone) that who would use to show that it is a wireless network, requiring a password. When I use my Xbox to connect wireless now, he said: "you connect to an unsecured network. Are you sure you want to continue? »

  I used the web portal to select 'Factory Reset' of my router. I also told my iPhone to forget and not automatically connect wireless network. After factory reset, I went to the configuration section of the web page wireless network access router, put a new name for the wireless network, personal WPA2 enabled for 2.4 and 5 GHz networks, developed a completely new password for two I had never used before and then looked for the network on my iPhone. I chose it and it connected right away without asking for a password. Still once, the network does not appear with a padlock next to him in the list of devices to the network from my iPhone WiFi and my XBox says always that this is an unsecured network.

  When using my internet browser to access router, WiFi networks are both classified as WPA2 Personal and each has a password in the password box (and Yes, I recorded the changes - that's what it shows even if I disconnect and then reconnect to the router access.) I tried to remove the power cord for 30 seconds and plug in again and there is no change.

  It's quite a recent change, like maybe the last week or more. I don't know if there was a firmware update or what - my router is configured for auto updates and when I click to check the latest updates, it says that there are no more updates available.

  TL; Dr: said access my router my wireless security is turned on. None of my wireless devices see as secure WiFi networks and each of them can connect without having to type a password.

  Do a reset factory and set up from scratch.

  If this fails, try this:

  Manually download the FW file to the local office of PCs.
  Reset the router, use IE or FF with all security disabled add-ons, load the FW file and let you treat.
  Factory reset the router once more and set up from scratch.

• HP Photosmart B109: cannot connect the printer to the wireless network

  I have some setting wrong my printer for wireless printing. It has worked well in the past, but with my new macbook air - this isn't.

  I can't access the function where to add the printer to the wireless network (my router does not support WPS so his password WPA).

  I remember setting this up on a PC - easy with the driver provided by HP, but on the Mac, the configuration tool does not appear to be a function where I add the printer to the wireless network - and HP did not provide a driver, because it is supposed to work with the mac built-in software.

  The manual says only: "follow the instructions on the screen", but the printer does not have instructions on how to connect - on-screen tests, only that it is connected...

  Anyone who knows how to add the printer to a wireless network?

  Hello @Joahkim!

  Welcome to the HP community!

  I understand that you have a problem to set up all-in-one printer wireless HP Photosmart (B109n) with your new MacBook Air OS x 10.10. I want to help you with this.

  Have you changed your router or your password since the MacBook Air? If this is not the case, your printer can still be connected to the network and the trickiest part of that place will be done for us already.

  We will print a Network Configuration report to see if it is connected:

  • On the Control Panel, press the button next to Scan. The Scan/Wireless menu.

• ' Error' the settings saved on this computer for the network do not match the requirements of the network "while trying to connect to the wireless network

  Title: Cannot get an Internet connection!

  Connection Wi - Fi comes with a warning that 'the settings saved on this computer for the network do not match the requirements of the network"what should I do to get a connection?

  Hello

  -Did you do changes on the computer before this problem?
   
  Method 1: I suggest you follow the steps to run the troubleshooter from the
  link and check if the problem persists.
  Using the troubleshooter from network in Windows 7
  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7
   
  Method 2: I also suggest you to follow the steps from the link and check if it helps.
  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows
   
  Method 3: Follow the steps below to remove and add the wireless network.
  (a) click Start and select Panel.
  (b) select network and sharing Center and manage the networks without wire (on the left).
  (c) in the list, click on your network and Remove top.
  (d) you can then search for available wireless networks again and reconnect it to your network.
   
  Hope this information helps.

• C309g-m - unable to connect to the wireless network, touchpad hangs

  Hello.

  As PrintDoc has suggested, it's a new thread in the suite here, where I jumped in with a diversion to the station 23.  I'm sorry.

  Here are the details:

  (1) system:

  Router is Thomson TG585n provided by ISP O2/Telefonica.  Download high speed ADSL to ~ 9Mbps.

  3 devices connected and stable:

  -L' computer running XPSP3, connects to the router via homeplug (Ethernet on electrical wiring).

  -Laptop running Vista Home Premium, connects wirelessly with WPA2-AES.

  -Mobile phone runs Symbian 60, connect wirelessly in the same way.

  Router is configured to operate on channel 11 g wireless and accept new devices automatically with the appropriate security password.

  It is a House of 3 floors - router on the top floor has always worked. computer bureau on a middle floor with printer; laptop and the phone can be anywhere.

  So far so good.

  Now, I want to add the wireless printer and I'm really bad.

  (2) summary of symptoms:

  I bought the C309g-m on Amazon UK in January 2010.  USB connection with assistant easily.  Migrated to wireless via the front panel.  Easy. Then tried to add a 500 GB Freecom Network Drive (NAS device connected to the router) and has failed, because I didn't RTFM.  After removing the FND, I get an error message of HP to the effect that I have "tried to set the printer's IP address" and lost the connection to the printer wireless.  Have not seen this message since then, so I can't reproduce.

  As I said, I removed the FND, who never appeared on the network in any way.  However I still can't connect to the printer wirelessly.  The wireless connection wizard crashes after asking to specify a password.  The wireless network Test report that the radio works, but shows FAIL the entrance of 'No filter '.  I looked into the console of the router and there is nowhere to set the MAC address filtering, so I'm stumped.

  I tried to 'Add a device' CD, for network via USB settings.  It takes forever (30 minutes?) to come up with the same error "MAC address filtering.

  One last thing: if I leave radio turned on (the default lighting) will lock the touchpad after a few minutes to the home screen.  If I disable it, it's fine.  Once locked, the only way to stop is to unplug the power supply.

  Finally - all the base printer functions very well.  I can print and scan through the USB port and can take copies.

  Thoughts:

  (a) I think my router settings can be screwed.  I don't see a way to set limits to the DHCP pool, I should be able to.  However, since I was 3 devices that connect to the Internet I am reluctant to do a factory reset in case I lose those!

  (b) there's something wrong with the printer - but I don't know what.

  c) I could try temporarily move the printer to the i) door ii) within reach of hardwirable of CAT5 and wireless range

  (d) the fact that I can connect the printer (wireless) or DNF (cable) makes me suspect the router.  However, I have not received any support from O2: they said it was an internal problem of LAN/WLAN and nothing to do with broadband, therefore, were not willing to help.

  I spent hours on this and get nowhere.  Help, please!

  Tim.

  BTW - I'm in the United Kingdom.

  Well, I think that there are many more problems with 'atypical' routers and HP software as there are with HP printers.  I see not nearly as many problems with certified brand routers WiFi (like Linksys, Netgear and D-Link), as I do with large brands and Belkin.

  The worst offenders are rented modems/routers that your ISP provides.  For some reason, they have a lot of industrial property settings and firmware that simply don't play well with HP printers (may be others, but I would never buy another printer HP - I know way to much about printers after their design for 25 years).

  A reliable and good solution cheap is to go buy a $40 or $50 Linksys router and replace stuff not expensive you have (or paste according to your router/modem rented).   Time and time again, I've seen problems disappear just after installing a standard router.

  You can reserve an IP address for a wired connection, but because parts wired and wireless to the printer have separate MAC addresses, this IP address is not available for the wired connection.

  Read the thread if you wish.  Discover the solutions on this website if you want to, but I still think you have a defective printer.

• Satellite Pro A40 fell on the wireless network card; Damaged PCMCIA slot

  This morning my Satellite Pro A40 (Celeron 2.6) fell 40 cm. He fell right on the wireless network card that has been inserted. This card is still alive and so is the rest of the laptop, but the PCMCIA location is little damaged. I can insert PC cards almost completely, just the last piece (when the pins are) wrong.

  I removed the cover near the CPU, and there, I could see the inside PCMCIA slot; I could see the main part and the last part where the pins are. That little part as is pushed upward, as you can see in the pictures.

  I think I'd be able to fix myself this PCMCIA slot, but I can't remove it. I removed all the screws on the rear plate, but he is still blocked.

  Pics:

  PCMCIA slot

  The PCMCIA location; on the left, you will see the part with the pins, which is pushed upward. It's also what I see when I look at the pins in the PCMCIA slot. as they are pushed down, but I don't think they are folded.

  Wireless network card

  Wireless network card; It is a little damaged but it still works.

  Does anyone have an idea how I can remove the back plate, or another way to remove the PCMCIA slot and fix it?

  Hi Steve

  Well, I can give t well you not answer how you can just remove the PCMCIA slot.
  There are a lot of screws and to my knowledge, it is necessary to remove all covers and screws that are placed at the bottom of the unit and inside under the keyboard.
  Please check this specific device. Perhaps you have overlooked a few screws.

  But if it is impossible to remove the PCMCIA slot of the unit, I recommend to ask the service partner for a detailed instruction.

  Good luck

  Good bye

• Strangest thing: iPhones can't see the wireless network. Why not?

  Suddenly, an iPhone 5 and an iPhone 6 were not connected to the home network. I thought that the wireless router was to have a hiccup. Reset it and still no. Control a connected computer and internet. Thought that it was a wireless problem, but check the settings (I don't mess with) and they are fine. BUT, I realized my iPad is always connected to the network. IPhones don't even see the wireless network. SSID always broadcast on. I tried to enter the SSID and password manually, but iPhones say that the network does not exist. It's the strangest thing. What would make the invisible network for phones all of a sudden? Both phones are differnet OS running. One is the latest version, probably the previous version. It's a FiOS Actiontec router/router wireless. Everyone has heard of such a thing? I do not understand how it is possible...

  Try this on an iPhone. No matter which even with other iOS.

  Tap settings > general > reset > reset network settings

  You will need to enter the password for Wi - Fi.

• ProBook 4520 s - exchange of the wireless network card

  Hello everyone.

  I think the exchange of the wireless network card in my Probook 4520 s, due to the low flow.
  So I searched for a while a 5 Ghz supporting the card and found out that I am only able to get in the "white" cards list working. Then I looked at this page:

  http://h20000.www2.HP.com/bizsupport/TechSupport/document.jsp?lang=en & CC = US & objectid = c02487851 & jumpi...

  These cards can be any, that have been used in 4520 s. Mine (according to the Device Manager) is the Broadcom 4313 802.11b/g/n. This thing only supports 2.4 Ghz. Now, I looked at the list for a 5 Ghz supporting the card. I think that the 802.11A/B/G/N WLAN Intel HMC 572520-001 minicards can operate on 5 Ghz, because I read, that A appears only with maps of 2.4/5 Ghz. I read too, that maps of 2.4 / 5 GHz have 3 antennas, but on this card I only the slots for 2. Is this good? And this card would go into my 4520 s?

  Greetings,

  Colony

  Hi, colony:

  You are right about your statement about the cards being described as A/B/G/N dual-band.

  The best thing to do is look at Chapter 3 of your service manual.

  You can only order one of the cards listed as supported and it MUST have the HP reference on it or it won't work.

  I see only two possibilities for you...

  The 6200 Intel and Broadcom 4322.  Make sure you also get the part # that corresponds to what country you live.

  If your current Broadcom card has integrated Bluetooth, you will lose your Bluetooth capability if you order an integrated HP bluetooth module and probably the cable too.

  None of the dual-band cards have embedded bluetooth.

  Link to the service manual.

  http://bizsupport1.Austin.HP.com/BC/docs/support/SupportManual/c02439213/c02439213.PDF

  Then, you can order a card on the link below.

  If you do not live in the United States, you can change your country at the top of the page to yours.

  http://h20141.www2.HP.com/hpparts/default.aspx?mscssid=6857BCBBC4CD4470B9282F130A563697

  Paul

• Satellite Pro A200 cannot connect to the wireless network

  Hello

  I have a Satellite Pro A200 and Tuesday night I was able to connect to a wireless network. I received an update, rebooted and now it doesn t seem to work.

  I can see the wireless networks available via the Toshiba Radar but cannot connect to my usual wireless network.
  Also, the wireless network icon disappeared from my system tray and if I go to Control Panel/network connections, I can't even view available networks because there is no option to do so.

  Any ideas?
  the FN/F8 will work?
  Help! Please, I beg you!

  Have you tried using System Restore and restore the operating system on time earlier?
  Maybe this will remove the update installed, and you can again use the WLAN.

  Check it out.

• Sat Pro M30: Can't see the wireless network.

  In my work, we have the wireless network. When I search the network I don't see. the wireless signal is strong.my laptop Satellite Pro M30's.

  Could you please have the solution or know what the problem is.

  Hello

  Have you used the Atheros WLan or Intel WLan card?
  As far as I know if you unit has an Atheros WLan card you should always use the Atheros Client Utility to connect to some networks.
  In this case, the option use Windows to configure my wireless network must be disabled. If you the Intel card this option must be checked.

  Please visit this site and points.
  http://www.laptop.uwaterloo.ca/help/users_wireless_troubleshoot_list.html

  Good luck

  Good bye