Add the second drive of my OPTIPLEX 7010

Similar Questions

• Add the second drive to ATC - 780

  I just purchased an ATC-780-UR61 with a 2.5 ssd "standard that I would add as a second disk as the startup disk and use the disk of 1 TB for storage. Now, I understand that there are only 2 SATA connectors on the motherboard - the one used by the 1 TB drive and 1 by the dvd player.

  Is it possible to add a second drive on this PC? I read some other models have a m2 connector to add a ssd drive to, but I don't see any documentation that the ATC-780.

  I can confirm:

  NGFFM1 m2 SSD connector

  It is on the right side of the motherboard near the SATA 2 ports.

• Available to add the second internal hard drive to 17-e117dx

  Hello

  Can you let me know, if there is provision to add the second internal hard drive for HP Pavilion e117dx 17.

  If so, one) is there requirments or the specifications of the hard disk (any make or model); (b) what equipment will be needed and where I can get to and c) Finally will be doing so make sure the warranty of my laptop HP Sub

  HP Pavilion

  Product: F9J38UA #ABA

  Model: 17-e117dx

  Thank you

  Not in the way you probably do. Here is the Service Manual:

  Manual

  See Page 50. Unlike the Envy 17 and Pavilion dv7, Pavilion 17 has that a single hard drive Bay. The only way to add a second hard drive is to remove the DVD (optical drive) and insert a DVD to the hard drive bay adapter. The manual shows how to remove the DVD player and you can buy the adapter at amazon.com or jacobsparts.com. Note that this is a 9.5 mm thick disc, not a 12.7 mm. Both types are available. I do not recommend the adapter DVD player solution because you lose the use of the optical drive, and also because the interface of optical drive is usually not as fast as the main hard drive interface. Always fast enough for simple storage and you can run a video of her, but you do not want to edit the video of this disc, for example.

  https://www.jacobsparts.com/items/HDDBAY-02/

  If you decide to go the route of adapter DVD I would buy a large capacity 5400 RPM SATA 2.5 inches wide and drive hard thickness 9.5 mm. No sense in buying a reader more expensive high-performance.

  http://www.Newegg.com/product/product.aspx?item=N82E16822178006

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• HP compaq 8200 elite sff: Add the second hard drive to 8200 elite sff

  I installed a second hard drive, but the system does not reqagnize it.  I connected the blue sata port.  Any help?

  Well shit, now I have to retype my response... I typed in Notepad, but it seems that I can't copy and paste into this box.

  I agree with DFBonnett, the second disc will only work on the BLACK, not BLUE light connector.

  The way I Win-10 to see the second drive was to go to the management of the computer, and then under storage, click Disk Management: the drive is presented as a disc 1 but not show the program explores until I received a letter from the disk drive... MAGIC, the player will now display as the letter assigned to the I gave him 'E' with a backup label.

  I tried what erico posted but has not worked, but I thank all of you who have tried to help.

  I give credit to Umbutu, he saw the drive without having to do anything myself.

  Hey Microsoft, look at what Linux can do... lol

• Adding a second drive to my Optiplex 755

  I bought an Optiplex 755 renovated a few months back that came with a floppy (really?). I decided to add a second drive, so I removed the disk and put a Seagate 750 GB drive in its place. I entered the program installation and active the drive, rebooted, went back into the Setup program to verify that the disc was recognized that it was. BUT now, whenever I restart the machine, I have the black screen with the following text:

  Replacing the HARD drive is not valid, continued use can lead to long-term reliability problems HDD please press that F1 in you want to continue.

  It also gives me the choice to press F1 to continue, F2 to enter setup or on F5 to run tests.

  I press F1 and it starts normally.

  My question is how or what I do to eliminate this black screen? Because if I restart and let the system is here and waiting forever.

  Thanks for your help.

  The DT, SFF, USFF systems REQUIRE specific Western Digital or SAMSUNG drive model. Replacing the HARD drive is not valid is specific to 745 and 755 SFF and ULTRA-COMPACT systems.

  The DT, SFF, USFF models will have a thermal message.  The model of the Tower does not care the drive Type.  This is due to "thermal considerations.

  

  Desktop Dell 755 is configured to reject anything but a hard drive Western Digital or Samsung, claiming that it is due to "thermal considerations.  This is for Desktop and SFF and ULTRA-COMPACT models.

  "HDD replacement is not valid" Message on a Dell Optiplex - Article KB - 329305 computer | Reference Dell

• Add the second disc

  I can add a second drive in a HP ENVY 17-J190NB

  Best regards

  lucvg

  Yes, and here is the part you are looking for:

  http://www.newmodeus.com/shop/index.php?Main_Page=product_info&cPath=2_5&products_id=542

  Here is a video showing how do:

  https://www.YouTube.com/watch?v=wx3dMGXrGCc

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• Pavilion 9408nr: Add a second drive for another main drive for laptops

  How can I add a second drive for another main drive of laptop computers. I took the car on the same cell type that crashed by the motherboard. I put it in drive Bay 2. Problems with starting. I sometimes want to boot from disc 2. Is there a MBR somewhere? Are there jumpers to make it slave. Sometimes it will install the software on 2 without any question. Is there a way to make a slave?

  Important-copy all data on the second hard drive you want to save on the first hard drive.

  MBR of Windows with the hard drive. Use Windows Explorer to locate the second hard drive. Right-click on it and format it.  Once this done, all what one is a storage device and not bootable until the operating system is installed to it.

  The BIOS will only see the hard drive as a bootable as it will now be the only drive with a MBR boot sector.

  The days of placement of the jumpers to determine master or slave on the disks hard is long gone. SATA drives have no jumpers slave\master like the old school IDE and Eide did.

• Can I add a second drive to an edition four dv7t-7000?

  The HP parts store said on a drive has been supported, but configuration options have shown

  several configuration with two drives.

  I had hoped that I could add a caddy and power/bus connector from the parts store.

  Only, I have configured the machine with a drive and add a second drive (from my dv7 dead 3085 dx).

  The machine is supposed to arrive June 18

  Thanks for the ideas...

  Jerry

  The answer is a qualified Yes.

  The kit suitable for the dv7t-7000 is ' 681976-001.  This kit comes with the

  Caddy and a power/bus short and long cable. It also has some screws

  the disk drive on the caddy.

  It contains also the 2 screws M2.5xL4 which will be attached the main drive caddy to the

  the computer chassis, but there is no screws to attach the second drive caddy to

  the framework.

  the recommended screws are 2.5 M x 9 L.

  I picked up two 2.5 M x 8L live in ACE hardware work fine.

  Jerry

• Advanced conditional action does not work when I add the second condition

  I use CP 8. I can't understand why I'm running on this problem. I have a series of If-Then conditional actions, but I am running into problems. I narrowed down it to this problem.

  It is a simple check box that must show either the box or not.

  

  As long as I have only one condition, it works fine. As soon as I add the second condition, it stops working.

  

  Any suggestions? I appreciate the help!

  Rick and I tried to explain that a conditional action is always executed completely. This is the reason that the second decision has been reset what had been done in the first in your first question. I have a lot of articles on my blog where I point out that bad sequence in the decision (or) is causing most of the problems with conditional advanced (shared) actions.

• Add the second NETWORK card to vSwitch

  I'm working on trying to add to install a second NIC physical to the vswitch which is installed by default when ESXi. I use the code below, but when I run it, it disconnects in fact the main physical network card and of course, I then lose connection. I tried different varients of this and even finished by adding a port of vmk, which I didn't do. I just want to add the second network card as a standby card network.

  #Add second NIC to the virtual switch
  $nic = Get-VirtualSwitch -VMHost $currentHost -Name "vSwitch0"
  Set-VirtualSwitch -VirtualSwitch $nic -Nic vmnic1
  

  The cmdlet Set-VirtualSwitch accepts a string array as the value of the parameter - Nic. So you should be able to:

  #Add second NIC to the virtual switch
  $nic = Get-VirtualSwitch -VMHost $currentHost -Name "vSwitch0"
  Set-VirtualSwitch -VirtualSwitch $nic -Nic vmnic1,vmnic2
  

  Best regards, Robert

• Add the second virtual disk at Vm

  Hey guys,.

  I just loaded ESXi 4 on a server and I created 2 virtual machines and I went to add a second drive to a virtual machine and it gave me an error message stating "there are not enough licenses to complete this operation. "Feature hotplug not approved, requires have have.

  Has anyone ever seen this error before?

  Thank you!

  You must now close comments to add an additional drive.

• RAID-1 failed, the second drive does not start in RAID

  I bought a Dell 531 running Vista with RAID1 set up on two 300 GB drives.

  And that works very well... but then the first disc got a bad place.

  Ideally, I could unplug this drive and run the other player;

  However, the second disc has a RAID boot sector!

  [he has a normal boot sector, so if I plug it into the unused (non-RAID) SATA-3 slot, it will start]

  Should be no problem, just start the recovery DVDs and let Vista install a good start...

  But NO!  The DVD version does not see the drive.  (I tried to load the sataraid drivers, no joy)

  Note: if I have the drive failed in the RAID and the second drive in SATA-3, it starts to SATA-3.

  If I put the two drives on the RAID, it starts on the failed disk.

  Now I have a replacement for the defective drive.

  How to make 'good' initialization as a RAID drive and rebuild the new drive?

  How can I get a boot sector capable of Vista/Raid on the disc?

  
  

• Add the second hard drive in the Dell Optiplex 780 SFF

  Hello

  I have dell Optiplex 780 SFF (Small Form Factor) PC. It has 3 options of SATA. I want to add 2nd hard drive in it, but I see no power for 2 hard drive cable.

  At the present time, I have a SATA Hard Drive and a SATA Super Combo. But the power cable from the SATA Super combo is very unique, I can not able to give the power of this cable to my 2nd hard drive.

  Is it possible to add 2 hard disk in the PC case?

  Best regards

  Dani

  Hi Dani,

  The SFF is using a drive slim lens that does not have a standard SATA power connection. You will need to buy an adapter or a SATA power cable splitter to power a second hard drive.

• Add the second hard drive to HPE-400Z

  I am trying to add a secondary hard drive to expand the storage space that I only have 10% of free space on the current.

  "Will buy one online" Seagate Desktop drive HARD 2 to 7200 tr / MIN SATA 6 Gb/s 64 MB Cache 3.5 "-drive retail Kit internal (STBD2000101)" enters the cage OK? Existing drive is Seagate 1 TB guess so, but do not get it and discover it doesn't work.

  This disc has new SATA data and power cables.

  It is clear that there is a free connection of motherboard "SATA2" for data, I can see it. Sounds easy.

  What I can't understand is where and how the POWER cable is connected to... or what might be able to be used which already exists for power connectors in the office. There is a certain and they all have beautiful marking... "P3,"P8",...".

  I found instructions on installing hard drive on HP site... everything is clear for me except for this problem of power cable.

  Did he help me with that?

  GWRootjr, welcome to the forum.

  This is an adapter 'Y' which should solve your problem:

  http://www.Walmart.com/msharbor/IP/24359037?wmlspartner=wlpa&adid=22222222227017782207&wl0=&WL1=g&WL2=t&WL3=40881390152&WL4=&wl5=PLA&wl6=78811224272&Veh=SEM

  You can connect a SATA power cable to do two on one.  This will allow you to connect the second HDD.

  Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

• Add the second hard drive to a desktop Pc HP Pavilion P6-2100

  I want to add a second hard drive to a HP Pavilion A1700n Pc desktop to a new HP Pavilion P6-2100 Desktop Pc, so I can transfer files.

  milehisb,

  Welcome on the user forums.  Section manuals PDF from HP did not offer a guide to upgrade and Service.

  There are several options, depending on your needs and your expertise with the internal components of a computer.

  If you goal is to simply get the data off the drive, then put it back in the A1700n, I would use #1.

  (1) use this external adapter for occasional use:http://www.newegg.com/Product/Product.aspx?Item=N82E16812232002

  (2) first search to find if you have a spare Sata power plug. Or you will need an adapter (molex 4pin to Sata).

  http://www.playtool.com/pages/psuconnectors/connectors.html

  http://en.Wikipedia.org/wiki/Serial_ATA

  As the player in question is VIsta, it does not start correctly and could delay the start of WIN7.