Adding a firewall in a Multinetted router

Similar Questions

• How to access internet throug a firewall of the Linksys router?

  Recently, I went to the ADSL2 + Internet broadband.

  So bought router "CISCO Linksys WAG120N" as my hardware firewall (FortiGate60) had no any port to connect to ADSL.

  Now I am accessing internet throug the Linksys router above and do not use the firewall because I don't know how to configure the firewall to get access to the internet through the firewall of the router.

  My previous broadband service was directly connected to the WAN port on the firewall because it was compatible.

  Please help me to configure the firewall to access the internet from the router through the firewall.

  Thank you

  You must configure the WAG120N in Bridge mode and then configure your firewall to your (probably PPPoE) internet connection.

• Adding a laptop computer to this router

  I'm not at all techminded and need help. We have a BESFR41 router and want to add our laptop (wireless). Can it be added to this router?

  Thank you!

  Yes, you have two choices for the BEFSR41 has no built-in support for wireless.

  (1) If you want to connect your laptop's wireless the BEFSR41 and on the Internet, you must purchase a "access point" wireless network that will carry out the connection of your wired LAN (ports on the BEFSR41) and your wireless laptop.  Consider a Linksys WAP54G, relatively cheap and easy to hang your BEFSR41 was.  This is what I have at home (a wired router, two WAP54G).

  or,

  (2) connect to your laptop through a wired connection (ethernet).  Get a cable, connect a LAN to the laptop and the BEFSR41 port.  Not as convenient and you will be tied by the length of the cable, but it will be faster than a wireless G connection.

  Or you could the BEFSR41 of pit and get a router that took both wired and wireless support.

  Hope this helps,

  Russ

• Adding a firewall for the MC FW which is located on the outside area

  Hi all

  Is it possible to add a firewall for the FW MC that is located on the external interface of the firewall? If so, what commands do you need on the firewall?

  Thank you and best regards,

  Hello

  In principle might be possible, what need the VMS Svr (FW MC) is a communication channel to the target, the outside Firewall (firewall EXTERNAL) device.

  You can try the following, to confrm.

  Your topology/flow very probably as follows:

  inside intf: EXTERNAL Firewall: ouside intf<->INTERNET CLOUD<->internet router<->router internet<->outside intf:PERIMETER Firewall: inside intf<->VMS:FW MC

  A. for the EXTERNAL firewall, configure:

  1 activate https & ssh access to/from the server of virtual machines. Access to the Svr VMS must be via a public IP address that mapped to the firewall's PERIMETER server.

  2. open access HTTPS & ssh (tcp 443 & 22). SSH may be optional, but you can activate it as well. HTTPS is required to communicate with the virtual Svr computers.

  Enable http server

  255.255.255.255 out http

  2. for ssh, generate a key for the firewall. The condition is as follows:

  -set the host name: "abc123 hostname.

  -define the domain name: "domain name xyz".

  -generate the key: "ca generate rsa key. The button of the module is between 512 and 768, 1024, 2048

  -Save the key: "ca save all."

  B. for the PERIMETER firewall, configure:

  1 static machines card virtual FW MC Svr to address external public IP for firewall mgt traffic

  public static xx.xx.xx.10 (Interior, exterior) aa.aa.aa.50 netmask 255.255.255.255

  2. open the ACLs on the external interface to the public IP address of external firewalls VM FW MC

  outside permit tcp host yy.yy.yy.100 host xx.xx.xx.10 eq https access list

  access-list outside allow host yy.yy.yy.100 host xx.xx.xx.10 eq ssh tcp

  outside access-group in external interface

  * yy.yy.yy.100 is an EXTERNAL firewall outside interface IP

  3. by default, the configuration of the VMS OPR statically with a public IP address, it should be able to go internet. But if you have ACLs on the inside interface, you need to enable access to the EXTERNAL firewall via https and ssh (tcp 443 & 22).

  inside permit tcp host xx.xx.xx.100 host yy.yy.yy.10 eq https access list

  access-list inside allow host xx.xx.xx.100 host yy.yy.yy.10 eq ssh tcp

  group-access to the Interior in the interface inside

  Also, enable/add ICMP on the two outside & inside to test accessibility for both devices. If you have ACLs on internet router, make sure that you allow the two firewall EXTERNAL and VMS Svr pass-through.

  It is a purely theoretical Setup. It may not work or need some changes.

  Rgds,

  AK

• Adding multiple Airport Express to a router/network Apple no?

  Hi all

  You are looking for assistance.

  Until yesterday, I had an Internet ADSL connection and home network WiFi connection that consisted of a base no routing modem, connected to a time Capsule. The extended wireless network had 3 Airport Express connected.

  My ISP (TPG in Australia) past my ADSL to the new NBN yesterday and have sent me a new HUAWEI Modem/wireless router. That's why I need is no longer my Time Capsule for routing.

  My question is now; Can I connect my A-Express to the router not Apple to create a large network similar to what I had before? I did a little reading and apparently not!

  Thanks in advance.

  Can I connect my A-Express to the router not Apple to create a large network similar to what I had before?

  Sorry, but no.  Feature of "extend" Apple owns. The Express devices can only wireless "extend" the signal from another router from Apple.

  You can still use the time Capsule to provide a network... wireless signal and the expresses may 'extend '.

  You could use the wireless of the Huawei product for "guest", or disable wireless on the device if you do not need two wireless networks.

• Adding additional Ports Ethernet to the router EA6300

  Friends,

  I have a setup of typical network with a cable modem in progress of execution to an EA6300 wireless router. The EA6300 also has a cable ports but I have 4 of those filled and I would like to extend it. I have an older Linksys ethernet hub, but it does seem like one of the entries EA6300 to plug in the supply plate works. Is there a way that it works, or do I need another piece of equipment?

  Greg

  But of course the without wire in this particular book didn't work for a long time, so I had to revisit this issue and found out that the ethernet hub works very well except for port 1. I am logged in ports 4 & 5 and all is well. This solution should work perfectly for the foreseeable future and thank you for all the support and assistance with this!

• password re: ADDING A COMPUTER to MY Cisco router connect

  When I add a computer to my Cisco connect Router that they can see the password - or key to connect to my internet. Y at - it anyway to hide this information from a computer, I add to my router.

  There is nothing of this nature in the parental controls, which means that they can add this wireless connection to another device.

  Thank you for your help

  Nowadays wireless device have the functionality to show for the wireless password, they are configured for. Nothing you can do about it unfortunately.

  What you can do, is use the MAC address wireless filtering to limit the devices which can connect to your wireless network.

• Dynamic routing for VPN Failover L2L

  Hello

  Can someone offer me some advice on this please?

  I have attached a simple diagram of our EXTENSIVE referral network.

  Overview

  • The firewall is ASA 5510 running 8.4 (9)
  • Basic to the Headquarters network uses OSPF
  • On ASA static routes are redistributed into OSPF
  • On ASA for VPN static routes are redistributed into OSPF with 130 metric so redistributed BGP routes are preferred
  • Basic network has a static route to 10.0.0.0/8 to Corporate WAN, which is redistributed into OSPF
  • Branch Office WAN uses BGP - routes are redistributed into OSPF
  • The branch routers using VRRP for redundancy of the IP for the default gateway of local customers.
  • Branch router main past off VRRP IP to router backup when the WAN interface is down
  • BO backup router (. 253) contains only a default route to the internet
  • In normal operation, the traffic to and from BO uses Local Branch Office WAN
  • If local BO WAN link fails, traffic to and from the BO uses IPSec VPN via public Internet

  I try to configure dynamic routing on our network for when a branch switches to the IPsec VPN. What I want to happen (not sure if it is possible) is for the ASA announce the subnet to the remote end of the VPN in OSPF to Headquarters.

  I managed to get this working using IPP, but for some reason any VPN stay up all the time when we are not in a failover scenario. This causes the ASA added the table as a static route is the remote subnet in it and do not use the announced route of OSPF from the core network. This prevents the BO customers access to the Internet. If I remove the IPP on the VPN setting, ASA learns the route to the subnet via the WAN BO - resumes normal operation.

  I have configured the metric of the static routes that get redistributed into OSPF by ASA superior to 110. This is so that the routes redistributed by the WAN BO OSPF BGP, are preferred. The idea being that when the WAN link is again available, the routing changes automatically and the site fails to WAN BO.

  I guess what I need to know is; This design is feasible, and if so where I'm going wrong?

  Thank you

  Paul

  Hi Paul,.

  your ASA maintains the tunnel alive only because this path exists on ASA.  This is why you must use IP - SLA on ASA to push network taffic "10.10.10.0/24" based on the echo response, using the ALS-intellectual property

  Please look at the example below, in the example below shows that the traffic flows through the tunnel, only if the ASA cannot reach the 10.10.10.0/24 network via the internal network of HQ.

  This configuration illuminate ASA.

  Route inside 10.10.10.0 255.255.2550 10.0.0.2 track 10

  (assuming 10.0.0.2 ip peering from inside the ip address of the router to HO)

  Route outside 10.10.10.0 255.255.255.0 xxx.xxx.xxx.xxx 254

  (value of 254 is a more expensive route to go via IPSec tunnel and x = the bridge by default-ISP)

  ALS 99 monitor

  type echo protocol ipIcmpEcho 10.10.10.254 inside interface

  NUM-package of 3

  frequency 10

  Annex monitor SLA 99 life never start-time now

  track 10 rtr 99 accessibility

  Let me know, if this can help.

  Thank you

  Rizwan James

• Firewall

  Firewall - I have a router which has its own built-in firewall and configure it to be safer.

  OSX has its own firewall which I lit mode health.

  I'm wasting my time having and which would effect the speed of the internet?

  The active firewall in stealth mode.

• Cannot add a permanent route to the routing table.

  Hello world
  I tried to add a routing table that for some reason I can't do a ping on the Internet of some windows xp machines and I was adding "see Pei add 0.0.0.0 mask 0.0.0.0 " and after you type this command, I was able to do a ping on and everything was going well until I rebooted. "." Whenever I reboot I am unable to ping but if I add "PEI route add 0.0.0.0 mask 0.0.0.0 it works again."

  It print my route continued under the road, but it doesn't seem to work when I reboot. Any help would be greatly appreciated.

  Persistent routes:
  Network gateway address mask network address metric
  0.0.0.0                                  0.0.0.0                                  1

  Any help would be greatly appreciated.
  Michael

  Original title: Windows XP adding a road permanent in the Routing Table (persistent route)

  Hi Michael Rodrigues of La Mancha,

  I wish you post your question in the TechNet Forums because it caters to an audience of it professionals.

  Check out the link-

  TechNet forums

  Hope this helps!

• Linksys WRT160n SPI Firewall

  I recently installed a Linksys WRT160n mainly to its advantage as a hardware firewall. I chose the wireless router because I intend to buy a laptop later. In the meantime, since I don't need wireless, I disabled the it. This router always provide firewall protection to my PC with the wired connection until I SPI Firewall Protection enabled?

  Thanks for help.  Alton

  The WRT is NAT that will make your inaccessible since the internet LAN unless you configure port forwarding, port triggering, DMZ or compatible UPnP host. The SPI Firewall protects especially the router.

• Close the port 455, is it necessary? I have windows firewall IT and using Windows Essentials.

  How to close port 445?  Should it be closed? What effect will have open/closed? I am a novice user and understand many uses and ways to configure certain parts of my computer. This open port sparked yet another in the functioning of my PC. Thank you Jerome.

  I can't imagine why you would want to do and I have no intention of frelling with any of my Windows machines to try it for you. If you feel better close your port 455, simply use the Windows Firewall to do. You must take the advice of Steve Gibson with a grain of salt. If your computer is clean, you have a good antivirus installed, you are using a firewall, are behind a router and practice "Safe Hex" then find something else to worry about. But that's just my opinion.

  Safe Hex:
  http://www.getsafeonline.org/
  https://www.mysecurecyberspace.com/
  http://www.GetNetWise.org/
  http://www.Microsoft.com/protect/default.aspx
  http://www.elephantboycomputers.com/staying-safe.PDF

  MS - MVP - Elephant Boy computers - don't panic!

• Removing static route get % corresponding to any error no route to remove

  I'm trying to remove a static route, I added:

  -------------------------------------------------------------------------------------------------

  R2 #show ip route
  Code: C - connected, S - static, mobile R - RIP, M-, B - BGP
  D - EIGRP, OSPF, IA - external EIGRP, O - EX - OSPF inter zone
  N1 - type external OSPF NSSA 1, N2 - type external OSPF NSSA 2
  E1 - OSPF external type 1, E2 - external OSPF of type 2
  i - IS - Su - summary IS, L1 - IS - IS level 1, L2 - IS level - 2
  -IS inter area, * - candidate failure, U - static route by user
  o - ODR, P - periodic downloaded route static

  Gateway of last resort is not set

  172.168.0.0/29 is divided into subnets, subnets 1
  S 172.168.0.0 [1/0] via 192.168.2.2
  C 192.168.1.0/24 is directly connected, FastEthernet0/0
  192.168.2.0/30 is divided into subnets, subnets 1
  C 192.168.2.0 is directly connected, Serial0/0
  R2 #conf t
  Enter configuration commands, one per line.  End with CNTL/Z.
  R2 (config) #no ip route 172.168.0.0 255.255.255.0 192.168.2.2
  % Corresponding to any no route to remove
  R2 (config) #r2 #show ip route

  ----------------------------------------------------------------------------------------------------

  I was training establishment of a static routing on three routers r2 (2600xm) connected to r1 (2600xm) via maps module T1 on the serial ports. connected to r1 is a router 2500 old called PC.

  I removed the static routes off r2 and PC but when I get to r2 I connect to 2500 another console cable that I use to access a server I get the above error.  all IP addresses are just generic subnets that I created to play with static routing.   I can't remove someone has any ideas?

  you use the subnet mask different than the one you used. According to the route table entry mask is 29

  Try this,

  1] r2 (config) #no ip route 172.168.0.0 255.255.255.248 192.168.2.2

  or 2] another easy method would be to check the working config and copy stick with 'no' at the beginning.

  See the race | include the ip route

  Copy the static route statement and paste this what with 'no' in the global configuration and check the routing table.

• SG300-52. Prefer to send traffic to the default gateway rather than static route? Network stops if I disable ICMP redirects.

  I have 4 switches, each act as their own with a 26 subnet mask. They have static routes for every other switch. The firewall has a static route to each switch. If I unplug the LAN of the Firewall interface, traffic stops the flow of the switches. If I block the side LAN firewall, ICMP redirects, traffic stalls outside.

  So if you are connected to this switch, say that you pull an ip address of 192.168.122.20. Your front door is the 192.168.122.62 switch. If you try to access a server 192.168.127.142, the SG300 sends your traffic to 192.168.127.254 to get an ICMP redirect, rather than simply to communicate directly with 192.168.127.50.

  My network 'basic' is 192.168.127.0/24 vlan1 and the firewall is 192.168.127.254

  This is the route of one of my switches table (which has 192.168.122.0/26 and ports run on vlan122)

   Maximum Parallel Paths: 1 (1 after reset) IP Forwarding: enabled Codes: > - best, C - connected, S - static S 0.0.0.0/0 [1/1] via 192.168.127.254, 73:48:13, vlan 1 C 192.168.122.0/26 is directly connected, vlan 122 S 192.168.123.0/26 [1/1] via 192.168.127.123, 73:48:13, vlan 1 S 192.168.124.0/26 [1/1] via 192.168.127.124, 73:48:13, vlan 1 S 192.168.125.0/26 [1/1] via 192.168.127.125, 73:48:14, vlan 1 C 192.168.127.0/24 is directly connected, vlan 1 

  In any case, what gives? Why the switch would first try to send the stream to the firewall?

  EDIT: Here is the server routing table:

   [email protected]/* */:~$ ip route show default via 192.168.127.254 dev eth0 192.168.122.0/26 via 192.168.127.122 dev eth0 192.168.123.0/26 via 192.168.127.123 dev eth0 192.168.124.0/26 via 192.168.127.124 dev eth0 192.168.125.0/26 via 192.168.127.125 dev eth0 192.168.127.0/24 dev eth0 proto kernel scope link src 192.168.127.142 

  Hi Jonathan,.

  I'm sorry. I misunderstood the routing table you want to accomplish. Your concern seems relevant given that the matching rule more will be selected instead of one: page 275 http://www.cisco.com/c/dam/en/us/td/docs/switches/lan/csbms/sf30x_sg30x/...

  ... "When the routing of traffic, the next hop is decided based on the longest match on the prefix (LPM algorithm). A destination IPv4 address might match several routes in the IPv4 static routing Table. The device uses the matching route with the higher, subnet mask that is, the longest match on the prefix. "...

  So go ahead and report it to the support team so the guys can make the laboratory, confirm it and declare additional:

  http://www.Cisco.com/c/en/us/support/Web/TSD-Cisco-small-business-suppor...

  Kind regards

  Aleksandra

• Failure to register SPA-3102 on "DSL-2750E" D-Link router

  Hi team

  I guess I'm able to clarify this here since its associated VOIP Cisco device. This SPA-3102 works fine with my old router. I wanted to have a WiFi router better and I installed D-Link router to "DSL - 2750th". Internet, everything works normally through this router but SPA3102 is does NOT record. I have a debug trace attached SIP & don't know why it's a failure of registration. Not any other filtering or firewall configured in the router and it works in accordance with all the default settings. Would you be able to give advice on this please?

  Debugging is nice, but it discloses the contents of INTERNATIONAL packages only. No responses. Intercept (incoming and outgoing) SIP packets.

  I have the average time - do not use the names in the proxy configuration. Use the IP address.