How to access internet throug a firewall of the Linksys router?

Similar Questions

• Why anyone cannot access a device of storage attached to the Linksys router?

  I have a Western Digital external hard drive connected to my Linksys WRT610N router.  It worked fine for months now.  When I set up the external hard drive I created a group assigned privileges and then accounts created in the Linksys router that my whole family could use, and then I had all my family use accounts that I created on the Linksys, for access.

  Today, I decided to disable one of the accounts (I was worried as the computer that may have been infected, and I didn't want any virus/malware/EC which - have - you to infect file sharing.)  After you determine that the PC in question was virus-free, I then went back into the menu for storage and reactive Linksys administration account.

  Now, no one can access the file share?

  I give up; Why has this happened?

  Try this:

  -Disable all existing users.

  -Create a new use

  -Give the Admin rights

  -Power cycle the router

  Now, check...

• How to access internet when the network is put in host-only mode

  I'm using workstation 6.5 version.

  I need to know if I change the network configuration of host-only bridge then what will be required on a virtual computer to access internet from VM parameters?

  If this is not possible using host only then there at - it an alternative for the same?

  Connect NAT instead of guest only network. Your virtual machine should now be assigned a local IP address of the NAT internal dhcp server.

  You can also connect to the Internet through this network and also your virtual machine will talk to the host on a private network.

• Unable to access Internet Explorer under two of the five profiles on the same computer

  I have 5 profiles set up on my computer, one for each Member of the family.  When I try to access Internet Explorer or Word in two of the profiles I am unable to run the command.  Both applications work as they always have under the other three profiles.  I double click on and 'Open with' dialog box appears with "Recommended programs."  The only option in this area is "Internet Explorer". I select the option and click on , but I find myself in a continuous loop with the "Open with" dialog box  When I finally click I get an another dialog asking me to save or run "ssvagent.exe." I am able to cancel out, but I can't even open either application.  If I select I can open the document in word, but I can't access Word from the options menu or the shortcut I used last year.  I ran a virus scan today and 5 cases have been detected and removed.  I ran the scan under 5 profiles, but now I can't access BitDefender (my virus scan) under either of the two affected profiles.  Please notify. Henry

  Hello

  Try scanning from the utilities included in the link, how to get rid of malware and let us know what happens.

  How to get rid of malware.

  http://social.answers.Microsoft.com/forums/en-us/vistasecurity/thread/ba80504b-61f1-4D71-960f-b561798b7b42

  Concerning
  Anthony.

• How to share Internet between a computer and the Windows Phone?

  How to share internet via pc windows for windows phone?

  Hi magali,.

  I suggest you to refer to the links and check if it helps.

  http://answers.Microsoft.com/en-us/WinPhone/Forum/wp8-wpnetwork/Internet-sharing-not-working-in-Windows-8-Lumia/8bf52b82-ebd8-47dc-B3FC-c1ee06abb6d5?msgId=f83df1c9-F186-495B-b16d-41c09578afdb

  http://Windows.Microsoft.com/en-GB/Windows/Connect-Internet#1TC=Windows-8

  http://Windows.Microsoft.com/en-us/Windows-8/mobile-broadband-from-start-to-finish

  Hope this information helps. If you have any questions, please let us know.

• How to access a view of database at the Complutense University of MADRID

  Hello

  I'm working on a project to migrate 10g and 11g.

  I migrated some views of the database to 10g to the ucm 11g schema schema.

  In 10g, I am able to access these objects to display in the Configuration Manager applet and I am not able to do the same thing in 11 g.

  Some can help me on how we get access to views of the DB in 11gUCM.

  Thanks in advance.

  Kind regards

  Vijay

  http://jonathanhult.com/blog/2013/11/use-database-view-WebCenter-content-schema-view/

  Jonathan

  http://jonathanhult.com

• Laptop does not connect to the internet, office. Both use the same router. Tried troubleshooting, does not. Help!

  I have a desktop computer and a laptop. Both use the same router. The laptop does not connect to the network, but the office has no problem. My wireless adapter on the laptop is on, I tried troubleshooting. I tried to turn it off for 30 seconds then restart him. But nothing is resolved the problem. Any ideas would be helpful! Thank you

  Hello

  Maybe this can help.

  These steps and tell us where is the breaking point.

  Check the Device Manager for the wireless card valid entry.

  http://www.ezlan.NET/Win7/net_dm.jpg

  If there is no valid entry, remove any entry from fake and re - install the drivers for the wireless card.

  Check network connections to make sure that you have a network icon/entry wireless connection, and that the properties of the icon (right-click on the icon) are correctly configured with the TCP/IPv4 protocol in the properties of network connections.

  http://www.ezlan.NET/Win7/net_connection_tcp.jpg

  Make sure that if there is Wireless Utility a utility vendor is not running with the native Windows wireless utility.

  ----------------

  Make sure you firewall No. preventing / blocks wireless components to join the network.

  Some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible set up the firewall correctly, otherwise totally uninstall and get rid of its remaining processes that permit the own local network traffic flow.

  If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  ---------------------------

  Stack TCP/IP work should look like.

  Right-click on the wireless network connection card, select status, details and see if she got an IP address and the rest of the settings.

  http://www.ezlan.NET/Win7/status-NIC.jpg

  Description is the data of the card making.

  The physical address is MAC of the card number.

  The xx must be a number between 0 and 255 (all xx even number).

  YY should be between 0 and 255

  ZZ should be between 0 and 255 (zz all the same number.)

  The date of the lease must be valid at the present time.

  * Note 1. IP that starts with 169.xxx.xxx.xxx isn't valid functional IP.

  * Note 2. There could be an IPv6 entries too. However, they are not functional for Internet or LAN traffic. They are necessary for Win 7 homegroup special configuration.

  ---------------------------------------------------

  A message in the small window that says connected wireless doesn't means that you are really a valid functional connection.

  Above everything is OK, you must be able to connect to the router.

  Connection to the router means that you can enter the IP of the router base in an address bar in one go, being able to connect and configure the router menus see.

  If it doesn't connect to the router, journal newspaper from any computer that can connect to the router wirelessly with a wire, disable wireless security, make sure that the wireless SSID broadcast is enabled and try to connect with no. wireless security.

  Enable security wireless after you eat to make a functional connection.

  
  

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• How to access and control my firewall

  I have Windows XP, SP3 with all updates installed on my computer.

  I have problems with a Web site - my browser find the URL and load the website, but the program never ask for my login details; and after a few seconds, the program displays the error message from the server from their site indicating the invalid client-server dialogue

  The web manager tells me to check MY settings, but not those who - I suspect that my firewall is causing the problem - how to manage the settings on MY firewall

  Hi Bob,

  1. have you done any hardware changes or software on your computer before this problem?

  2. what browser do you use?

  3. which site are you trying to access?

  If you use Internet Explorer, you can follow this link & check if the problem persists:

  You cannot view a secure in Internet Explorer 8 Web site

  Reference: You cannot connect to or connect to Web sites secured in Internet Explorer

  Hope the helps of information.

• Cannot access Internet and all programs on the start menu. How to get rid of a virus on windows xp

  I was recently given a hand computer (compaq I tthink) so I'm not clear about all the fancy stuff to the extent of the ect CPU... but I know it has windows xp pro. in any case, a friend used my computer and for some reason any felt the need to download a program called 7-zip. Now, my computer is screwed... In the start menu > all programs, everything has disappeared! And I can access the system restore in normal boot and safe mode, but the window remains empty, we never really gave me the opportunity to use it. Oh and I can't get online in normal or safe boot mod either, what can I do?

  Original title: how to get rid of a virus on windows xp proremove a virus from windows xp pro

  Hello

  1. Why do you think that the computer is infected with the virus? See you pop - unwanted ups or odd behavior of all programs?

  2 have you made any changes to the computer before the show?

  3. did you run any online scanners to remove infections?

  4. What is the antivirus installed on the computer program?

  Method 1: Run a scan antivirus on your computer.

  www.Microsoft.com/Security/Scanner

  Note: If infections are detected during the scan, there is a risk of data loss because infected files will be deleted.

  Method 2: Safe mode with networking

   

  Step 1: Check if you can browse the Internet with success in Mode safe mode with networking.

  Networking Mode safe mode starts Windows in mode safe mode and includes the network drivers and services needed to access the Internet or other computers on your network.

  A description of the options to start in Windows XP Mode

   

  Step 2: Put the computer in a State of boot is a way to know which application is causing this problem.

  To help resolve the error and other messages, you can start Windows by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  Put your boot system helps determine if third-party applications or startup items are causing the problem. If so, you need to maybe contact the manufacturer of the program for updates or uninstall and reinstall the program.

  Step 1: Follow the steps in the link below to do the same thing:

  How to configure Windows XP to start in a "clean boot" State

  Note: After troubleshooting, be sure to set the computer to start as usual as shown here:

  Step 2: To configure Windows to use a Normal startup state

  After you have used the boot is a way to solve your problem, you can follow these steps to configure Windows XP to start normally.

  1. Click Start and then click Run.
  2. Type msconfig and click OK. The System Configuration Utility dialog box appears.
  3. Click the general tab, click Normal Startup - load all services and device drivers and then click OK.
  4. When you are prompted, click on restart to restart the computer.

  Method 3:

  Create a new user account and verify if you are able to access the program in the start menu.

  Try to connect with a different user has administrator rights account and then create a new user account.

  For more information, see these links:

  How to create and configure user accounts in Windows XP

  How to copy data from a corrupted to a new profile in Windows XP user profile

  I hope this helps.

• How to access my settings to develop in the library for LR6 Module?

  I'm used to be able to do a right click on an image (s) in the library Module and access the LR and develop settings to apply to one or more images. Now, in LR6, these settings no longer appear in the right click menu. Anyone know where they went? Is this unique to my setup?

  It is no longer available via the contextual (right click menu).

  You can access develop presets via the Panel to develop fast in the library.

• How to access additional tools by mousing over the triangle

  I can't access additional tools by positioning the mouse over the triangle at the bottom of the icon of the tool unless I have order click on the triangle.

  If I remember, ctrl-click on a mac is the same as doing a right click on windows. To access the tools without using the CTRL key you should have pressed the button on the mouse for a few seconds for them to pop up. I never heard them poping when hovering, but then again I'm on windows, so...

• How to access a keypad to type in the email address, etc. in trying to put in place applications

  I am trying to activate (eprint) APPS for my new HP 6600 1.  You will need to enter the email address, password, etc. to use applications such as Google Docs., scanning reception, ebox.  Everything is all ready to enter on the screen of the printer, but no keyboard appears.  The implementation seems complete and correct, and I can immediately print items such as easy forms (HP), but do not need to add email, password, etc. to use.

  I use VISTA: IE9 and Firefox (latest issue) are my browsers.  Thank you.

  PS There is no error message: I can't simply complete the task without a keyboard characgter.

  I'm sorry that I understand your question now.  In order to get the keyboard for all what you need to bring is your finger in the area to be filled once the slider rises the keyboard should appear automatically.

• How to access vector < int > data passed to the function of iteration?

  So, basically, I have all the work by accomplished Supercomputing in the Render() function and threw a vector < int > (with all my final pixel already calculated and stored inside values) to the iteration function.

  However, when I go to assign: output-> red-> green, out-> blue, out-> alpha , result is a revamped image:

  My pixel processing function that I pass to the iteration inside the function Render() function looks like this:

  IM with the final pixel data in a vector < int > called given that present a size() of (width * height * 4) with values in rgba order.

  public static PF_Err

  () drawTriangles8

  void * Conref.

  A_long xL,

  A_long yL,

  PF_Pixel8 * inP,

  PF_Pixel8 * output)

  {

  PF_Err err = PF_Err_NONE

  TriangulateInfo * tInfo = reinterpret_cast<TriangulateInfo* > (Conref);

  if (tInfo) {

  Output->Red tInfo->data= [(int) ((xL * 4) + (yL * tInfo->width * 4))];

  Output->Green tInfo->data= [(int) ((xL * 4 + 1) + (yL * tInfo->width * 4))];

  Output->Blue tInfo->data= [(int) ((xL * 4 + 2) + (yL * tInfo->width * 4))];

  Output->alpha tInfo->data= [(int) ((xL * 4 + 3) + (yL * tInfo->width * 4))];

  }

  return err;

  }

  I tried just to save the values of the original image with no calculations done RGBA and try them back on the resulting image so that it remains unchanged and I get always the same the smeared image search. No idea what's going on?

  This is not the point of my last answer.

  my point was that you store in your vector, the pixels in this order:

  x0y0 x0y1, x0y2... x1y0, x1y1, x1y2...

  Maybe the way you shoot you pixels from the vector assume they are

  ordered:

  x0y0 x1y0, x2y0... x0y1, x1y1, x2y1...

  If that's true, which would explain the image being on his side, and the

  the offset to the line you see.

• no internet but not connected to the wireless router

  I have 400 SL with windows vista installed.
  Everything worked well for years, until a few days ago.
  It is the symptom, and what I've done:
  1. the laptop CAN connect to the wireless network, no problem, very strong, just signal has no internet.
  cannot ping google.ca.
  In network and sharing Center:
  Computer---> network---> Internet
  ^                   ^
  |                     |
  Red Cross OK
  2. all other devices (iphone, ipad, other laptops) can connect to the network and internet.
  3 did a system restore on the eve of this stoppped working. always the same.
  4A bought a wireless adapter, always the same. but it works fine on the other laptop
  5 tried to set a static IP, subnet mask, gateway, still the same problem.
  6. any other device can ping each other with the exception of this laptop...
  7. the seller cordless tool is uninstalled (Lenovo connection management tool)
  8 rebooted a million times between all the steps
  9 safe mode with network has the same problem.
  10 tried to use other wireless, still the same problem...
  need help...
  Thank you
  -Virginia

  Hi Virginia,

  Thanks for posting your query in the Microsoft Community Forums.

  After the description of the problem, I understand that you can not connect to a wireless network on windows vista computer.

  I appreciate your efforts on this issue, however no need for you to worry we are here to help and guide you in the right direction.

  Help me with the information below.

  -Don't you make changes on the computer before this problem?

  I suggest you to disable temporarily security software and then check if you are able to connect.

  Method 1

  You can also temporarily disable the security software and check if it works.

  http://Windows.Microsoft.com/en-us/Windows-Vista/turn-Windows-Firewall-on-or-off

  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

  If disabling the security software solves the problem, then contact the manufacturer of the specific security software to fix the problem.

  Important: These steps may increase your security risk. These steps may also make the computer or the network more vulnerable to attack from malicious users or malicious software such as viruses. We recommend the process that this article describes to enable programs to operate as they are designed for, or to implement specific program features. Before you make these changes, we recommend that you evaluate the risks that are associated with implementing this process in your particular environment. If you decide to implement this process, take additional measures to protect the system. We recommend that you use this process only if you really need this process.

  Method 2

  Reset the router and see if that helps.

  Note: to help you reset the router, you can consult the manual that came with the router or the router contact manufacturer.

  You can see this help article.

  Wireless and wired network problems

  http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-Vista&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Hope this information is useful.

  Let us know if you encounter problems under windows in the future. We will be happy to help you.

• How can I put in my # to bridge the wireless router?

  When I type in my browser the http://[default_ip_gateway] it gives me a few fake site to join.

  I have the cord hooked cable between my Dell Demension 310 and my V515W printer, but I can't Bridge # put in the router.  Is there another way in addition to call it up on top of the Web browser?

  Thank you

  Gerrel

  Hello

  The gateway is usually the base IP address of the router (192.168.xx.xx) x = IP address of your router.

  If you put the IP address in the browser, you get the opening of browser session (in most of the router it resembles a logon web page)...

  To make sure that you do it correctly read the manual of your router.