Adding additional Ports Ethernet to the router EA6300

Similar Questions

• Re: Laptop not recognized on Ethernet to the router

  Hello

  I have a similar problem with an old book.

  HOST:
  -Laptop: Asus l3d
  -Equipped with a card: SiS 900 PCI Fast Ethernet Adapter
  -OS: Ubuntu server 14.04
  ROUTER:
  -Router: Netgear DGND3700v2 Firmware Version 1.1.00.24_1.00.24

  Parameters:
  -Laptop computer with the static IP.
  -Router with dhcp disabled.

  -----------

  QUESTION:
  The liaison between NB and Netgear ethernet works for some time. Exactly, the Netgear does not recognize the cable, plugged into the ethernet port on the router (called internal switch) of the ethernet of Brunswick.

  I'll try to explain it in a few steps:

  STEP 1: With everything well adjusted and connected the cable. If I start the NB and the router, the result is no connection, no ping and LED light for the no router port.
  Note: to the page web of the management of the router, I read that 4 ports (LAN1, 2, 3, 4) are not used.

  ... but...

  STEP 2: Now, with everything working, I play with one of the two ends of the cable (any of the two). Slowly, I Plug and unplug the cable into the ethernet port, a few times until the router port light. BRAVO! NB and Netgear are connected. There is a ping. All works until the next reboot of Netgear or NB
  Note: to the page web of the management of the router, I read that a port is used.

  STEP 3: While all the work normally. If I unplug the cable and I connect again, making this action at normal speed, the connection does not work as STEP 1. The only way to have a working link is to repeat the procedure in STEP 2.

  -----------

  I did a lot of testing, for example:
  -test NB, but work very well with other routers, AP NB, switch.
  -test the router, but the work of Netgear very well with the other PC.
  -change the cable.
  -on the NB to update the drivers.
  -on the NB, disabling auto-negotiation and manual setting.

  I think that in my case, the problem is the internal switch of the router. But it is a hypothesis.

  Thanks for any help.

  Hello Salvatore111

  Product Netgear do not officially support Linux so it could be just a strange problem with the drivers on the NB does not speak with the router.

  DarrenM

• How can I enable port forwarding in the router of the time capsule

  Does anyone know how to enable port forwarding in router Time Capsule Airport please?

  Port Mapping on the time Capsule airport cannot be enabled unless you have the right type of modem on your network.

  Thus, we need the number of brand and model of the device you're calling your "modem" before we can move forward. Please post back this information.  We do not need a series number... only the name of the manufacturer and model number of the modem.

• White LED of Ethernet to the router flashes constantly (to about 5 flashes per second)

  The Internet on my router Netgear (R7000 Nighthawk, AC1900) white LED flashes constantly (about 5 times per second), and it is originally the link on my modem light blinks constantly. All started about four days ago. I thought that my modem was defective, but I spoke with my ISP technical support who said it was the router that has been at the origin of the modem LED blink. I unplugged the power supply to the router, but when I plugged it in the problem has not been resolved. I also reset the router (using the reset on the back of the router) but that has not solved the problem. Any help would be most appreciated. Thank you.

  View that statistics is one of the purple buttons under the Internet Port pane.

  

• ENVY Phoenix Desktop - 850-065: Add the port ethernet on the desktop

  I want to add a second ethernet port on the desktop... any recommendations, the Gathas, the various factors to consider... I seem to have three ports of extension on the PCI bus... one of them would be the target (or what)... any recommendations on ethernet brand and model to consider...

  Any wisdom on the subject will be sincerely appreciated...

  Hello

  There are many models/products of ENVY Phoenix Desktop - 850-065 series. In any case, according to your description you can use a normal PCIe 1Gig card. There are a lot of cards around, 1 port, 2 ports or more. Please make sure that there are drivers CD or at least it shows you where to find driver (from the site of the manufacturer).

  Kind regards.

• WRT120N Wireless laptop connected to the router, but does not connect to internet

  I have a HughesNet HN9000 modem connected to a Linksys WRT120N router. I have two desktop computers, both running XP Home, connected to the router via ethernet .5e cables and work perfectly. I have a laptop running Vista Home Premium, I am trying to connect to the internet via the internal wireless card. According to me, the laptop connects with the wireless router, as it connects but says 'Local only' - it won't let me access the router IP/control panel. I tried to reset the router / modem as well as the parameters of the laptop, but I keep getting the same question.

  If I connect the laptop and the port #3 on the router via a cable .5e I can browse the Internet. But I need to be able to use the laptop throughout the House so electrician is not an option.

  I found this article which directed me to this download , which worked. If your help is most needed. Thanks anyway.

• Unable to connect to Homegroup Windows 7 between the Modem to the PC and the Modem to the router for PC users.

  I want to talk about WIRED computers, do not speak of wireless.

  I have 3 PC:

  -2 are connected via Modem directly to the PC.

  -1 is connected through router, and the router is connected to the modem.

  The problem, this is it, it cannot detect the homegroup that I created on the computer that is directly connected by modem.

  The 2 PC via modem are perfectly detected and connected to the homegroup, so I want to know what I would do to another PC (which is connected to the router via modem) detects the homegroup, I had already created?

  Help, please.

  A Modem can have only two ports, connect to the internet (Wide Area Network) and the second to a SINGLE local device. In most cases the internet Service Pwill provide with only an IP address so itself cannot connect to more than one at a time. In current solutions, it is very rare for a Modem to use. If as you say, you have several devices connected to this unit then he himself is a router but possibly with the Modem built in if you have ADSL ISP.

  If your second unit is also a router then that explains why you cannot connect all devices in the same residential group.

  Router 1 has created a Local Area Network including both PC and the WAN port on the Router 2. Router 2 has created another independent local network with the 3rd PC. It is very likely that the two local networks will be IPv4 and traffic can be routed between them correctly in both directions according to the two local networks subnet ranges.

  Even if they are properly configured to allow traffic that HomeGroup requires IPv6 that some home routers support fully and every Member of the residential group must be on the same LAN anyway, he will not support a routed connection.

  Remove the 3rd PC of the 2nd router and plug it into the direct 1 router, remove the router 2nd the 1st in order to free the port. 3 all PCs are now on the same local network and communicate both IPv4 and IPv6, and homegroup should work.

  If you need additional ports provided by the 2nd router for other devices is not part of this problem then consider replacing it with a switch. If you use Router 2 for other devices Wi - Fi irrelevant then you need a wireless access Point.

• Cannot add a permanent route to the routing table.

  Hello world
  I tried to add a routing table that for some reason I can't do a ping on the Internet of some windows xp machines and I was adding "see Pei add 0.0.0.0 mask 0.0.0.0 " and after you type this command, I was able to do a ping on and everything was going well until I rebooted. "." Whenever I reboot I am unable to ping but if I add "PEI route add 0.0.0.0 mask 0.0.0.0 it works again."

  It print my route continued under the road, but it doesn't seem to work when I reboot. Any help would be greatly appreciated.

  Persistent routes:
  Network gateway address mask network address metric
  0.0.0.0                                  0.0.0.0                                  1

  Any help would be greatly appreciated.
  Michael

  Original title: Windows XP adding a road permanent in the Routing Table (persistent route)

  Hi Michael Rodrigues of La Mancha,

  I wish you post your question in the TechNet Forums because it caters to an audience of it professionals.

  Check out the link-

  TechNet forums

  Hope this helps!

• I lost my router user name and the password and reset does not have without the router

  I haven't used my router wireless of Linksys WRT54G v5 for about 1 1/2 years and he needs now to a new place.

  I put a username and password I forgot for a long time for access to the web according to the security protocols for the modem and I lost the disc for the program control protocol.

  I tried pressing the reset button to clear the modem and it took the WPA Protocol off the power to the modem, so I can use it without any security, but this isn't a good thing.

  Help! How do unlock it so I can get to the security protocols and put back the security on my modem?

  StephanieD wrote:

  I haven't used my router wireless of Linksys WRT54G v5 for about 1 1/2 years and he needs now to a new place.

  I put a username and password I forgot for a long time for access to the web according to the security protocols for the modem and I lost the disc for the program control protocol.

  I tried pressing the reset button to clear the modem and it took the WPA Protocol off the power to the modem, so I can use it without any security, but this isn't a good thing.

  Help! How do unlock it so I can get to the security protocols and put back the security on my modem?

  To release your router to your previous settings.

  RESET the router the button is @ the back of it.

  Connect a computer to one of the ports numbered on the router.

  Access the UI of it http://192.168.1.1

  User name: (BLANK)

  Password: admin (all lower case)

  

• Compaq Presario CQ61-416sa and Atheros Ar 9285 connects to the router

  I have this laptop and wifi, it was working fine, now it won't connect to my router.  Before it would come with a list of all possible wifi (neighbors/shops etc.) connections now it doesn't.  My Iphone and blackberry connect to the wifi exactly the same as before.

  If I connect the laptop ethernet to the router I can get on the net

  Please can someone help

  Corrected, reinstalled windows 7 works perfectly again

• Port forwarding on the WAN IP unique vShield

  Hello, is it possible to do port forwarding "of the router outside the IP address' for the vShield Edge VM, or am I assume I have to add a second outside of the IP to perform port forwarding from a foreign port to worms a server in-house. Essentially, here's my problem:

  
  I want the vShield Edge IP, if I type the IP address of it on port 80, I want that it will to an internal server on this port. I am only able to do that if I add a SECOND outside address on the firewall. It is a problem because I don't want to burn two addresses by customer just to PAT. Any thoughts? It is an important situation. Thank you

  At the point where you need two survey periods to do this. Basically, the first IP address is dedicated to the NAT traffic.

  VCloud many users have requested to change this behavior, I hope that we will be able to use a unique IP address in the future. Even as a service provider with several available IPs, they are valuable, and it is a waste.

• Access to the network of a device ethernet via the ports of the router.

  I was wondering if someone can help me with a router configuration. I have an ethernet device, a built-in Digi Connect me stack ethernet. I put the IP, subnet, gateway, etc. on this device. It has a serverver web and telnet and FTP features. What I want to do, this is the device connected to a WRT54GS router to one of the ports on the back. Then I want to connect internet routers connecting to my local network. On the LAN, I have a PC I want to use to access the web page of the Digi device through the router. The LAN has affected the PC an IP address of 3.11.201.33 and assigns the router IP Internet of 3.11.201.32. The PC is set to dynamically set an IP address. I have configured the Digi device to have an IP address of 192.168.1.100. I want to open a web page on the PC and connect a digi device. I can't get this to work. I tried to add the IP address of the device Digi to the DMZ on the router, but that did not help. How can I get from the PC via the LAN, through the router, on the port that is connected to the Digi? Any help is apprecieated!

  Outgoing FTP for multiple devices behind the router need not any special installation... you will not need to pass all the ports for that.

  You can port forward more than a device with the stock firmware digi... I just forgot how port forwarding 'niche roles' it is on the page... the WRT54G V5 has 10, so assuming that no other device in transmitted port, you should be able to forward the ports ftp and telnet for 5 devices.

• Motherboard has 2 ethernet ports. both are connected to the router, only 1 is sending/receiving information.

  OK, my onderstanding I should be able to define a place for sending and one for receiving. How I do that... Both are connected to the router. If I unplug one, the other to rest and then work. But my? is how to work both for sending / and the reception. I have an ASUS Crosshair 590 MB, internet by cable that goes from router then to computer... the any 2 are connected to the router. SOMEONE HAS IT PLS! Can help to ya? THX, Nolan

  Hello

  Yes, this problem will cause a problem psychological too many users.

  Some vendors of motherboard put this second NETWORK card, because it cost them 30 cents to do this, and it seems not good for marketing.

  While users cannot let go of the poor port (30 cents) sitting there with nothing to do. (;_;)

  Jack, MVP-Networking. WWW.EZLAN.NET

• How to set up Time Machine via a HARD drive connected to the USB port on the router?

  Hi all

  I have an Arris Touchstone Data Gateway DG1670A/TW for my internet / wireless which was provided by my ISP.  There is a USB port at the back of the router and I was wondering if I could connect an external HARD drive to save the two Macbook Pro that I have in my house through Time Machine wireless?  If Yes, could someone provide me the details regarding how to set this up properly?

  I too, was thinking about making a 4 TB HARD drive - 2 and wanted to partition so that half of it would work for Time Machine and the other half I would be able to store photos that I take on my digital SLR and are in Lightroom.  Could this be a problem at all? I partition? or Time Machine just to use the available space and delete older backups to make room for additional photos?

  Thanks in advance for any help.

  A device third-party network attached storage (NAS) or a router is unsuitable for use with Time Machine.

  Apple has published a specification for network devices that works with Time Machine. No third party provider, AFAIK, does meet this specification.

  Apple does not endorse any device third-party network for use with Time Machine. See this support article.

  Network backup, use as destination an Apple Time Capsule or an external storage device connected to another Mac or a 802.11ac AirPort base station. Only 802.11ac base stations support time Machine, not older model.

• Ports Ethernet in router wireless set up as access point

  If I set up a wireless router as a wireless access point, can I still connect to the Ethernet ports on the router?

  Yes.