adding memory to a presario CQ57-489wm

Similar Questions

• Compac Presario CQ57-229WM: failure of Compac Presario CQ57-229WM Memory Module

  Compac Presario CQ57-229WM w / Windows 7

  I get the following text "Windows has recovered from an unexpected shutdown. A problem caused Windows to stop working correctly. Windows will notify you if a solution is available. »

  Followed by a crash dump

  Verification of results in the readers:

  Drive hard test Passed

  HDD SMART Passed

  Module memory failed

  1 732 608 bytes of memory tested system OK

  Fault memory test

  Any help would be greatly appreciated.

  One or maybe two sticks of memory failed. If it's not very common to have two fail - it wouldn't be a bad idea to replace both if you can afford it. You could also spend 4 GB of the 2 GB, you have now.

  Crucial is always a reliable source of memory and they have single sticks or a set. Click on 'Show memory more compatible upgrades' under the memory listed to see the simple sticks and sets:

  http://www.crucial.com/USA/en/compatible-upgrade-for/HP-Compaq/Presario-cq57-229wm

  You can remove a memory stick at a time and run the test to determine if one or both is a failure. Your interview Guide & shows how remove and replace memory:

  http://support.HP.com/us-en/product/Compaq-Presario-CQ57-200-notebook-PC-series/5091489/model/5111956/manuals?lang=en&cc=us

• Compaq Presario CQ57-104TU: upgrade Ram, memory (Ram Hynix PC3L-12800)

  Hello world

  I have a Compaq Presario CQ57-104TU. I recently decided to upgrade the ram (currently 1 x 2 GB Elpida PC3 - 10600 1333 Mhz). I bought 2 x 4 Gb Hynix HMT451S6AFR8A, PC3L-12800. Unfortunitely when I install the new Ram (Hynix)

  the computer does not start. Is there something I can do or the Ram is not compatible?

  Any help would be appreciated,

  André

  Here is the Service Manual:

  Manual

  See p.2. Specified memory is DDR3-1333 1.5 volt and you try to install low-voltage DDR3-1600. In addition, memory that you are trying to install is high density, because it has 4 blocks on each side, where I am betting that original memory was of low density (8 blocks). Long story short, it is not compatible. It do you no good to install DDR3-1600 by the way. Best of cases, it will anyway be downclock speed 1333.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• How can I upgrade my Presario CQ57 to make it faster?

  Hello

  My laptop is a bit slow, so I'd like to update some of the components to make it faster.

  Could you recommend me a better processor? & a RAM if you consider it necessary for this purpose?

  Compaq Presario CQ57 Notebook

  Intel (r) Celeron (r) CPU B800 @ 1.50 GHz 1.50 GHz

  2.0 GB OF RAM

  _ 64-bit Windows7

  Computer system product: 5CB21874YP

  Hewlett-Packard: 068C 110003204910000620100

  Thank you

  RAM is much easier updating. I recommend at least 4 gigs, and it will take up to 8. She takes DDR3-1333 SO-DIMM memory. CQ57-339WM seems to be your model.

  This is the service manual you need to swap processors:

  Manual

  The CQ57s equipped with a Celeron processor will accept only the Celeron processors. There are a couple more quickly available for your computer Celeron, but exchanging a Celeron for a another Celeron just doesn't seem worth it to me.

  If you want the computer to run more quickly install 4 GB of RAM and upgrade to a disk hard solid state. The speed improvement is actually more you'd get from opting for a faster Celeron processor. After the back if you want more specific suggestions.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• Computer laptop HP Presario CQ57 (Windows 7) will not start.

  Computer laptop HP Presario CQ57 (Windows 7) will not start.

  Memory test: past

  Smart Check: spent

  DST short: failure

  ID Q7PS33-5T76ND-MFKR5F-60VV03 failure

  Product ID: QE321UA #ABA

  Hard drive

  Hello:

  The failure of DST short is normally indicative of a hard drive that has failed and must be replaced.

  The operating system and the software can be reinstalled using recovery discs that you made or purchased from HP.

  In order to use the recovery disks, you need to replace the hard drive with one of the same storage capacity or more.

• Compaq Presario CQ57-339wm: I can swap different CPU into a model motherboard Celeron?

  Hey all,.

  I have a laptop Compaq Presario CQ57-339wm requiring a logic board replacement. According to the sticker on the Palm, it has an Intel Celeron processor clocked to Interior.

  According to the CQ57, the motherboard service manual I ordered (reference number: 646177-001) is "for use only with the computer models equipped with an Intel Core i5 or i3 processor processor and a graphics subsystem with UMA video memory.

  Since I have a Celeron CPU and motherboard instead, would replace this motherboard for the work of the Board of Directors i5? I think that the mobo, I ordered does not include a processor i5, just the current Board. I could swap the chip Celeron of the old Council to the Board of Directors i5, or that wouldn't work either? I have to install a compatible rod that matches the part number of the old mobo? (646174 001).

  If it won't work, I return to the Commission, as I have not yet opened and order a compatible card. Moreover, if the installation of the Board of Directors will work, and I just need the compatible CPU, I could order one that would correspond to the reference, like this eBay i3.

  "Violence is the last refuge of the incompetent." -Issac Asimov, from its roman Foundation.

  I think that you understood. The Celeron and Core Intel models use a different motherboard with a different chipset and processors cannot be exchanged.

• Presario CQ57 laptop: Compaq Presario CQ57 material

  Hello, I wanted to know if I could spend my processor Celeron in my Compaq CQ57 Notebook.

  In addition, Ram and graphics card can be improved?

  * I hope this is enough information *.

  Product name: computer laptop Presario CQ57

  Product number: QE264UA #ABA

  Serial number: [personal information]

  BIOS: F.38 - 17/12/2011 (068C 110003204910000620100)

  Review of keyboard: 23.4 A

  Total memory: 2.00 GB

  Processor name: Intel (r) Celeron (R) CPU B800 @ 1.50 GHz

  Hello

  Your computer supports up to 8 GB of RAM, as indicated:

  http://support.HP.com/RS-en/document/c03210811

  Please use the following manual to get the part # for CPU (page 82). The manual also shows you how replace/add RAM and CPU:

  http://h10032.www1.HP.com/CTG/manual/c02948186.PDF

  For graphics: no, the chip is soldered on the motherboard, it must be this new motherboard (= new computer).

  Kind regards.

• Black screen on startup, caps lock flashing - Compaq Presario CQ57 311SO

  I got this computer from a friend who owns a son.

  We do not know how or when it appeared first, but it's in this State for a few months now.

  It is a Compaq Presario CQ57-311SO and its a little more than 1 year, so store warranty has expired.

  What happens is that when you press the button power has nothing to display on the screen and you do not hear the sounds of typical start-up, the beep and the hard disk rotates upward.

  Instead of this, the Caps Lock key led flashes in the following model, 2 flashes pause 2 flashes.

  The computer is totally immune to any key, usb and cd entries.

  I tried the hard reset and memory sharing in different locations.

  But it seems that the bios itself is corrupt and failed.

  So my question is, can I Flash the bios somehow and make it work again?

  I tried a tutorial on how to do memory flash in FAT - 16 but no noticeable effect.

  Although the guide could be wrong or I could have done something wrong so I would really like to try again if I could get help with instructions from you nice people

  Thanks in advance.

  I solved the problem in dismembering the computer laptop everything and put back the battery CMOS.

  Thank you.

• The fan on a Compaq Presario CQ57 Windows laptop settings

  Hello, I have a Compaq Presario CQ57 and the fan runs all the time at full speed. I opened the laptop and did a fan and cleaning of the motherboard, I applied thermal paste, I changed in the bios the option #Fan always on # Enable to disable, I updated the Bios but still nothing... it sounds like a jet of fighter.should I change my fan? someone who has a Council?

  I already ordered the fan and I will keep you posted as soon as I get it and install it.
  Thank you very much

• Presario cq57: System to disable the code

  I have presario cq57 gives disable me the code 78432038

  Trying to access bios to remove passwords

  Try loader.

  67590018

  Use this code to go into the BIOS.

  Disable all passwords that are enabled.

  If demand for CURRENT password using this code.

  Request NEW password just press ENTER.

  If asked to hit just to CHECK password to enter.

  Save and exit.

  REO

  I must inform you that these services are not endorsed by HP, and that HP is not responsible for any damages that may occur to your system using these services. Please be aware that you do so at your own risk.

• adding memory cards

  Hello

  I want to improve my iMac, by adding memory cards.

  My problem is not sure about the maximum limit of memory can I add I m.

  Can you tell me if it's 32 GB or 16 GB or 12 GB?

  Each location must have the same value or if we can mix different sizes of memory?

  How is the maximum that iMac 11.3 with i7 processor supports? 32 GB, 16 GB or 12 GB?

  Thank you very much!

  Mariana

  System details:

  Model name: iMac

  Model identifier: iMac11, 3

  Processor name: Intel Core i7

  Processor speed: 2.93 GHz

  Number of processors: 1

  Total number of Cores: 4

  (By heart) L2 cache: 256 KB

  L3 Cache: 8 MB

  Memory: 4 GB

  Processor speed of interconnection: 4.8 GT/s

  Boot ROM version: IM112.0057.B00

  Version of the SCM (System): 1.59f2

  BANK 0/DIMM0:

  Size: 2 GB

  Type: DDR3

  Speed: 1333 MHz

  Status: OK

  Manufacturer: 0x80CE

  Part No.: 0x4D34373142353637334648302D4348392020

  Serial number: 0x792C8110

  BANK 1/DIMM0:

  Size: 2 GB

  Type: DDR3

  Speed: 1333 MHz

  Status: OK

  Manufacturer: 0x80CE

  Part No.: 0x4D34373142353637334648302D4348392020

  Serial number: 0x792C8112

  BANK 0/DIMM1:

  Vacuum

  BANK 1/DIMM1:

  Vacuum

  go to http://www.crucial.com/ basics and put in your mac details and they will show the compatible modules and configurations

• Need to "downgrade" my Compaq Presario CQ57 of Windows 8

  A few weeks ago, I upgraded my Presario CQ57 to Windows 8.  Well, I don't like her, and I now have a desktop computer that is anyway a touchscreen that works beautifully.  I thought about my computer limited knowledge that I had created the backup disks to restore my system to Windows 7 Home Premium, but it turns out it's a repair disc.

  Is it possible for me to order the right from HP disk to return my laptop for Windows 7?  I found something on the internet with this post: http://h30434.www3.hp.com/t5/Desktop-Operating-Systems-e-g/The-Cleanest-Install-Windows-7-Recovery-D...

  I don't know what to do.  Any help would be appreciated!  Thank you!

  Hello:

  Please read the info on the link below to see how to order for your PC recovery disc:

  http://support.HP.com/us-en/document/bph07143

  I believe that my instructions are easy to follow to make your own install of W7 media, if you do more like that.

  You can also make your own regular install of W7 disc and allows to reinstall windows 7 If you can read the product key 25 character microsoft on the COA sticker on the case of the PC. You will have none of the programs supplied with the PC using this method, however.

  If you can read the Microsoft windows 7 25-character product key, you can download simple Windows 7 ISO files to burn on a DVD for the version of windows that is installed on your PC, and which is listed on the Microsoft COA sticker on your PC case.

  Burn the ISO with the option to burn the ISO on your DVD burning program and burn it at the slowest possible speed that will allow your program. This will create a bootable DVD.

  Or use the installation of Windows 7 USB/DVD tool to compile the ISO file that you download from Digital River. Link and instructions below. You need a 4 GB flash drive to use the USB compilation method.

  http://www.microsoftstore.com/store/msstore/HTML/pbPage.Help_Win7_usbdvd_dwnTool

  Use 25 characters on the PC product key to activate the installation.

  The key will activate a 32 or 64 bit installation.

  Then go to the support of the PC and driver page to install the drivers you need.

  Link to downloads ISO of W7 is below.

  http://www.mydigitallife.info/official-Windows-7-SP1-ISO-from-Digital-River/

  Paul

• Compaq Presario CQ57: bios error 501

  What should I do to get rid of this problem?  Please help me someone.

  Welcome to the community of HP @ANAKONDA support,

  Thank you for joining on the HP's Support Forums! It is a great place to ask questions, find solutions and get help from others in the community! I read your post on the Forums of HP Support.

  I wanted to join you and help! I understand that you have a problem with an APPLICATION (501) BIOS ERROR on your Compaq Presario CQ57 laptop PC.

  Remove all USB devices. Disconnect all non-essential devices, because they can cause some problems.

  Try starting your laptop normally after having disconnected all. If that does not solve the problem, please continue with troubleshooting.

  The next step would be for you to try to restore the BIOS. You will see that the document says:

  If the BIOS of your laptop becomes corrupted, and a failure to upgrade the BIOS or damage caused by a virus, the computer can display all the following symptoms:

  • The computer displays the error message from the BIOS APPLICATION ERROR 501.

  After restoring the BIOS see if you can start the computer normally.

  Thank you for your participation in the Forums of HP where we want to help you as well as others who may encounter a similar problem that you have. Remember to mark this message as an acceptable Solution if it solves the problem for you.

  To show recognition for my efforts please click the Thumbs Up below.

  If you need assistance, I would be more than happy to continue to help you. Please re-post with the results of the resolution of the problems. Could you please also provide your model number (How can I find my model number or product number?)

  Have a wonderful day!

• which processors I've upgraded to I have a compaq presario cq57-339wm windows 7 64 bit

  which processors I've upgraded to I have a compaq presario cq57-319wm windows 7 64-bit like faster processor, I have a processor Intel Celeron B800 now.

  This will depend on whether or not your installed version of Windows 7 is Windows 7 Starter.

  The following processors are compatible with the motherboard of your laptop.

  Intel Core i5 - 2430 M 2.40 GHz processor
  (1333 MHz FSB, 3, 0 - MB L3 cache, dual core,
  35 W; not supported on computer models
  equipped with Windows 7 Starter 32-bit
  operating system)
  √
  Intel Core i3 - 2330 M 2.20 GHz processor
  (1333 MHz FSB, 3, 0 - MB L3 cache, dual core,
  35 W; not supported on computer models
  equipped with Windows 7 Starter 32-bit
  operating system)
  √
  Intel Core i3 - 370 M 2.40 GHz processor (1066 -
  MHz FSB, 3, 0 - MB L3 cache, dual core, 35 W;
  not supported on equipped computer models
  with Windows 7 Starter 32-bit
  operating system)
  √
  Intel Pentium P6300 2.26 GHz processor (3.0-
  MB L3 cache, dual core, 35 W)
  √
  Intel Pentium P6200 2.13 GHz processor (3.0-
  MB L3 cache, dual core, 35 W)
  √
  Intel Pentium 2.20 GHz processor (2.0-B960
  MB L2 cache, dual core, TJ85, 35 W; not
  pressed equipped computer models
  Windows 7 Starter 32-bit operating system)

  Intel Pentium 2.10 GHz processor (2.0-B950
  MB L2 cache, dual core, TJ85, 35 W; not
  pressed equipped computer models
  Windows 7 Starter 32-bit operating system)

• Compaq Presario CQ57: compaq Presario cq57 forgotten system password disabled code: 77564960

  Compaq Presario cq57 forgotten system password disabled code: 77564960

  At the password prompt, try 68442366